Professional Documents
Culture Documents
Chapter 1. Disassembly & Assembly Guide: MS-1 Main Section Disassembly
Chapter 1. Disassembly & Assembly Guide: MS-1 Main Section Disassembly
Chapter 1. Disassembly & Assembly Guide: MS-1 Main Section Disassembly
1 Confidential
- Main Section -
MS-1 Main Section Disassembly
SZ Series
1.MS-1-D.2 Confidential
Battery Pack
Release Lever
Lock Lever
Slide the Lock Lever to the UNLOCK side. While Release Lever is slid in the left, remove the Battery Pack.
3) 4)
Eject Lever
Push the Eject Lever once, and the Eject Lever pops up. Push
Hook the finger on the Dummy Card (EXP) and remove it.
the Eject Lever once again, and remove the Dummy Card (PC).
SZ Series
1.MS-1-D.2(a) 4 [MA] Confidential
1)
SZ Series
1.MS-1-D.3 Confidential
Heatsink
1) 2)
Screw:B2 Cover (CPU)
While disengaging the detent (three places), remove the Cover (CPU).
Remove the four screws.
3) 4)
Heatsink
Screw:B2
Raise the Heatsink in the direction of the arrow1, and remove the Heatsink
Remove the two screws.
while removing the A portion diagonally upward (arrow2).
SZ Series
1.MS-1-D.4 Confidential
Cover (Memory)
1) 2)
Screw:B2
Detent
Cover (Memory)
SZ Series
1.MS-1-D.5 Confidential
Keyboard
1) 2)
Keyboard
2
Keyboard
Disengage the detent (two places), and release the Keyboard. Slide the Keyboard in the direction of the arrow 1 to release the detent
* Disengage the detent by pushing it by using a bamboo spatula. (five places), and turn it toward you and put it on the Plamrest.
3) 4)
Keyboard
FPC
FPC
Slide the lock lever in the direction of the arrow to release the lock,
Peel off the Sheet (MG KB5). disconnect the FPC, and then remove the Keyboard.
SZ Series
1.MS-1-D.6 Confidential
Palmrest
1) 2)
Screw:B1
FFC
Raise the lock lever to release the lock, and disconnect the FFC (two places). Remove the three screws.
3)
Palmrest
2
HDD
1) 2)
Tape (Common)
Screw:B2
Peel off the Tape (Common) and Filament Tape. Remove the three screws.
3) Connector
3 [ADD]
1
D
HD
FPC
Convex
Disconnect the FPC, and remove the HDD while taking out it from
under the convex portion (one place).
* When disconnecting the FPC, be sure to remove it from the
direction of the arrow 1. SZ Series
1.MS-1-D.8 Confidential
Sheet
HDD
D
HD
Bracket
Remove the four screws, and then the Bracket (two places). Peel off the Sheet from backside of the HDD.
3) 4)
HDD
Filament Tape
HDD
FPC
Hood (Keyboard)
1) 2)
Button (WLAN)
Detent
Detent
SZ Series
1.MS-1-D.10 Confidential
SWX-214 Board
1) 2)
3) 4)
Screw:B5
SWX Board
SWX Board
Harness
1) 2)
IFX Board
FFC
Screw:B5
Remove the one screw, and then the IFX Board. Pull out the FFC vertically and disconnect it.
3)
IFX Board
FFC
Reserve Battery
1)
Reserve Battery
Harness
SZ Series
1.MS-1-D.13 Confidential
Coaxial Cable
1) 2)
Screw:B5 IFX Board
Coaxial Cable
Escutcheon (L)
SZ Series
1.MS-1-D.15 Confidential
LCD -1
1) 2) 3 [ADD]
Screw:B13
Lug Terminal
Sheet (Paste Cable) Harness (LCD)
Remove the one screw. Peel off the Sheet (Paste Cable).
* It secures the Lug Terminal.
3) 4)
Camera Model
Harness (Microphone)
Harness (LCD)
LCD -2
5) 6)
Camera Model Camera Model
Tape (Harness)
Harness (Camera)
7)
Screw:B8
LCD
Cap (Hinge)
Harness
SZ Series
1.MS-1-D.18 Confidential
1) 2)
Connector
Bluetooth Module
Tape (Harness)
3) 4)
Bluetooth Module
Coaxial Cable
8 [CHG]
Disconnect the coaxial cable.
Peel off the Sheet (Paste Cable).
* Pull out it vertically.
SZ Series
1.MS-1-D.19 Confidential
ANL-66 Board -1
1) 2)
Screw:B2
FPC
Remove the two screws. Raise the lock lever to release the lock, and disconnect the FPC.
3) 4)
FFC
A
Notch
Harness
ANL-66 Board -2
5) 6)
ANL Board
Speaker (L)
SZ Series
1.MS-1-D.21 Confidential
Chassis (MG)
1) 2)
Screw: Red-B8 / Blue-B9
FPC
3)
Chassis (MG)
Screw:B5
FPC
8 [CHG]
SZ Series
1.MS-1-D.23 Confidential
Screw:B2
Connector
Remove the one screw. Remove the Optical Disc Drive while disconnecting the connector.
SZ Series
1.MS-1-D.24 Confidential
IFX-435 Board -1
1) 2) 4 [MA]
Sheet (USB Upper)
WAN Model
Tape (Harness)
Peel off the Sheet (USB Upper). Peel off the Tape (Harness).
3) 4) 4 [MA]
Sheet (ODD)
WAN Model
FFC
Lock Lever
IFX-435 Board -2
5) 6)
Screw:B5
FPC
Remove the two screws. Raise the lock lever to release the lock, and disconnect the FPC.
7)
IFX Board
Harness
FPC
IFX Board
SZ Series
1.MS-1-D.27 Confidential
1)
DDC Board
Connector
Convex
Disconnect the connector, and remove the DDC Board while pulling it
out from under the convex portion.
SZ Series
1.MS-1-D.28 Confidential
Cover (BATT)
1) 2)
Screw:B2
Cover (BATT)
Remove the two screws. While disengaging the detent (two places), remove the Cover (BATT).
SZ Series
1.MS-1-D.29 Confidential
Mother Board -1
1) 4 [MA] 2) 3 [ADD]
4 [COR]
Busteraid(CPU Upper)
Peel off the Sheet (FPC EMI). Peel off the Busteraid (CPU Upper).
3) 3 [ADD] 4)
FPC
Tape (Harness)
Mother Board -2
5) 6) Screw:B5
A B
Harness
FPC FPC
Lock Lever
Disconnect the FPC (two places). Remove the one screw, and disconnect the Harness.
*A : Pull out it in the direction of the arrow. * The screw secures the lug terminal.
B : Raise the lock lever to release the lock, and disconnect the FPC.
7) 8)
Screw:B2
Mother Board
1) 2)
A
FFC FFC
Coaxial Cable
Disconnect the coaxial cable coming from the WAN Antenna (Base Unit).
Remove the three screws and the WWAN Unit.
* Disconnect the coaxial cable vertically.
SZ Series
1.MS-1-D.30(b) 4 [MA] Confidential
5)
WWAN Unit
SZ Series
1.MS-1-D.31 Confidential
Screw:B8
FPC
FPC
Remove the two screws, and then the FPC. Pull out the FPC vertically upward, and disconnect it.
3) 4)
Screw:B5
Card (Modem)
Harness
Card (Modem)
Remove the two screws, and then the Card (Modem). Turn over the Card (Modem), and disconnect the Harness.
SZ Series
1.MS-1-D.32 Confidential
Card (Modem)
SZ Series
1.MS-1-D.33 Confidential
CNX-349 Board
1) 2)
Screw:B5
Filament Tape
9 [ADD]
Peel off the Filament Tape (two places) and the Shield Tape (C). Remove the two screws.
FPC
Lock Lever
Escutcheon (R)
Escutcheon (R)
1) 2)
Screw:B5
Cover (Modem)
3)
Escutcheon (R)
1) 2)
Adhesive Tape (Cover BATT)
Sub Plate (WAN Antenna)
Remove the WAN Antenna (Base Unit). Remove the Sub Plate (WAN Antenna) while disengaging the
*The Adhesive Tape (Cover BATT) is attached on the bottom of it. detent (one place).
3)
Coaxial Cable
Sheet (DC)
Harness (DC)
Peel off the Sheet (DC). Remove the Harness (DC) by lifting it up vertically.
3) 4)
Cover (Modem)
Harness (RJ45/11)
Remove the Harness (RJ45/11) by lifting it up vertically. Remove the Cover (Modem).
SZ Series
1.MS-1-D.36 Confidential
CNX-348 Board
1) 2)
Screw: Red-B8 / Blue-B5 Bracket (Dock-L)
Gasket
Peel off the Gasket, and remove the three screws. Remove the Bracket (Dock-L).
3) 4)
Connector CNX Board
FPC
Escutcheon (L)
Remove the CNX Board while removing the connector portion from
Pull out the FPC vertically.
the Escutcheon (L).
SZ Series
1.MS-1-D.37 Confidential
Bracket (VGA)
SZ Series
1.MS-1-D.38 Confidential
Escutcheon (L)
1) 2)
Screw:B5
Escutcheon (L)
3)
Sheet (USB-F)
PC Card Connector
1) 2)
Screw:B5
Sheet (PCMCIA)
3) PC Card Connector
Convex
FPC
SZ Series
1.MS-1-D.41 Confidential
Screw:B18
Adhesive Tape
3) 4) 5 [ADD]
Bracket (OPT-R)
2006.04.26 5 [ADD] Logo of Model Specification (Page 17) / Parts (Page 41) 2.00
2006.07.06 8 [CHG] Attachment (Page 18) / Screw (Page 22) 2.30
2006.08.23 9 [ADD] Attachment (Page 33) 3.00
2006.10.04 11 [ADD] Screw (Page 30) 3.20
SZ Series