Professional Documents
Culture Documents
Instatec Sabana - DH1 - Z4
Instatec Sabana - DH1 - Z4
76
www.hilti.si
Company: Trimo d.o.o. Page: 1
Address: Prijateljeva cesta 12 Specifier: Primož Kozlevčar
Phone I Fax: | E-Mail: primoz.kozlevcar@trimo-group.com
Design: DH1_Z4 Date: 7. 04. 2022
Fastening Point: DH1 Z4
Specifier's comments:
1 Input data
Anchor type and size: HST3 M10 hef2
Return period (service life in years): 50
Item number: 2105713 HST3 M10x100 40/20
Effective embedment depth: hef,act = 68.0 mm (hef,limit = - mm), hnom = 76.0 mm
Material:
Approval No.: ETA 98/0001
Issued I Valid: 4. 05. 2021 | -
Proof: Design Method EN 1992-4, Mechanical
Stand-off installation: eb = 0.0 mm (no stand-off); t = 4.0 mm
Baseplate :
R lx x ly x t = 90.0 mm x 670.0 mm x 4.0 mm; (Recommended plate thickness: not calculated)
Profile: no profile
Base material: 2
cracked concrete, C25/30, fc,cyl = 25.00 N/mm ; h = 200.0 mm, User-defined partial material safety
factor gc = 1.500
Installation: hammer drilled hole, Installation condition: Dry
Reinforcement: No reinforcement or Reinforcement spacing >= 150 mm (any Ø) or >= 100 mm (Ø <= 10 mm)
no longitudinal edge reinforcement
Reinforcement to control splitting acc. to EN 1992-4, 7.2.1.7 (2) b) 2) present
R
- The anchor calculation is based on a rigid baseplate assumption.
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
1
Hilti PROFIS Engineering 3.0.76
www.hilti.si
Company: Trimo d.o.o. Page: 2
Address: Prijateljeva cesta 12 Specifier: Primož Kozlevčar
Phone I Fax: | E-Mail: primoz.kozlevcar@trimo-group.com
Design: DH1_Z4 Date: 7. 04. 2022
Fastening Point: DH1 Z4
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
2
Hilti PROFIS Engineering 3.0.76
www.hilti.si
Company: Trimo d.o.o. Page: 3
Address: Prijateljeva cesta 12 Specifier: Primož Kozlevčar
Phone I Fax: | E-Mail: primoz.kozlevcar@trimo-group.com
Design: DH1_Z4 Date: 7. 04. 2022
Fastening Point: DH1 Z4
N
NEd £ NRd,s = Rk,s EN 1992-4, Table 7.1
gM,s
y c · NRk,p
NEd £ NRd,p = EN 1992-4, Table 7.1
gM,p
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
3
Hilti PROFIS Engineering 3.0.76
www.hilti.si
Company: Trimo d.o.o. Page: 4
Address: Prijateljeva cesta 12 Specifier: Primož Kozlevčar
Phone I Fax: | E-Mail: primoz.kozlevcar@trimo-group.com
Design: DH1_Z4 Date: 7. 04. 2022
Fastening Point: DH1 Z4
N
NEd £ NRd,c = Rk,c EN 1992-4, Table 7.1
gM,c
0 Ac,N
NRk,c = NRk,c · 0
· y s,N · y re,N · y ec1,N · y ec2,N · y M,N EN 1992-4, Eq. (7.1)
Ac,N
0 1,5
NRk,c = k1 · √fck · hef EN 1992-4, Eq. (7.2)
0
Ac,N = scr,N · scr,N EN 1992-4, Eq. (7.3)
c
y s,N = 0.7 + 0.3 · 1.00 EN 1992-4, Eq. (7.4)
ccr,N £
1
y ec1,N = £ 1.00 EN 1992-4, Eq. (7.6)
1+ ( 2 · eN,1
scr,N )
1
y ec2,N = £ 1.00 EN 1992-4, Eq. (7.6)
1+ ( 2 · eN,2
scr,N )
y M,N =1 EN 1992-4, Eq. (7.7)
2 0 2 2
Ac,N [mm ] Ac,N [mm ] ccr,N [mm] scr,N [mm] fc,cyl [N/mm ]
35,088 41,616 102.0 204.0 25.00
Group anchor ID
1
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
4
Hilti PROFIS Engineering 3.0.76
www.hilti.si
Company: Trimo d.o.o. Page: 5
Address: Prijateljeva cesta 12 Specifier: Primož Kozlevčar
Phone I Fax: | E-Mail: primoz.kozlevcar@trimo-group.com
Design: DH1_Z4 Date: 7. 04. 2022
Fastening Point: DH1 Z4
V
VEd £ VRd,s = Rk,s EN 1992-4, Table 7.2
gM,s
0
VRk,s = k7 · VRk,s EN 1992-4, Eq. (7.35)
0
VRk,s [kN] k7 VRk,s [kN] gM,s VRd,s [kN] VEd [kN]
23.600 1.000 23.600 1.250 18.880 2.340
V
VEd £ VRd,cp = Rk,cp EN 1992-4, Table 7.2
gM,c,p
VRk,cp = k8 · NRk,c EN 1992-4, Eq. (7.39a)
0 A
NRk,c = NRk,c · c,N
0
· y s,N · y re,N · y ec1,N · y ec2,N · y M,N EN 1992-4, Eq. (7.1)
Ac,N
0 1,5
NRk,c = k1 · √fck · hef EN 1992-4, Eq. (7.2)
0
Ac,N = scr,N · scr,N EN 1992-4, Eq. (7.3)
c
y s,N = 0.7 + 0.3 · 1.00 EN 1992-4, Eq. (7.4)
ccr,N £
1
y ec1,N = £ 1.00 EN 1992-4, Eq. (7.6)
1+ ( 2 · eV,1
scr,N )
1
y ec2,N = £ 1.00 EN 1992-4, Eq. (7.6)
1+ ( 2 · eV,2
scr,N )
y M,N =1 EN 1992-4, Eq. (7.7)
2 0 2 2
Ac,N [mm ] Ac,N [mm ] ccr,N [mm] scr,N [mm] k8 fc,cyl [N/mm ]
35,088 41,616 102.0 204.0 2.670 25.00
Group anchor ID
1
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
5
Hilti PROFIS Engineering 3.0.76
www.hilti.si
Company: Trimo d.o.o. Page: 6
Address: Prijateljeva cesta 12 Specifier: Primož Kozlevčar
Phone I Fax: | E-Mail: primoz.kozlevcar@trimo-group.com
Design: DH1_Z4 Date: 7. 04. 2022
Fastening Point: DH1 Z4
V
VEd £ VRd,c = Rk,c EN 1992-4, Table 7.2
gM,c
0 Ac,V
VRk,c = kT · VRk,c · 0
· y s,V · y h,V · y a,V · y ec,V · y re,V EN 1992-4, Eq. (7.40)
Ac,V
0 a b 1,5
VRk,c = k9 · dnom · lf · √fck · c1 EN 1992-4, Eq. (7.41)
0,5
a = 0.1 · () lf
c1
EN 1992-4, Eq. (7.42)
0,2
= 0.1 · (
c )
d nom
b EN 1992-4, Eq. (7.43)
1
0 2
Ac,V = 4.5 · c1 EN 1992-4, Eq. (7.44)
c2
y s,V = 0.7 + 0.3 · 1.00 EN 1992-4, Eq. (7.45)
1.5 · c1 £
0,5
y h,V = (1.5h· c ) 1
³ 1.00 EN 1992-4, Eq. (7.46)
1
y ec,V = £ 1.00 EN 1992-4, Eq. (7.47)
1+ ( 2 · eV
3 · c1 )
y a,V = √(cos a ) + (10.5 · sin a )
V
2
V
2 ³ 1.00 EN 1992-4, Eq. (7.48)
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
6
Hilti PROFIS Engineering 3.0.76
www.hilti.si
Company: Trimo d.o.o. Page: 7
Address: Prijateljeva cesta 12 Specifier: Primož Kozlevčar
Phone I Fax: | E-Mail: primoz.kozlevcar@trimo-group.com
Design: DH1_Z4 Date: 7. 04. 2022
Fastening Point: DH1 Z4
a a
bN + bV £ 1.0
Concrete failure
a a
bN + bV £ 1.0
Comments: Tension displacements are valid with half of the required installation torque moment for uncracked concrete! Shear displacements
are valid without friction between the concrete and the baseplate! The gap due to the drilled hole and clearance hole tolerances are not
included in this calculation!
The acceptable anchor displacements depend on the fastened construction and must be defined by the designer!
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
7
Hilti PROFIS Engineering 3.0.76
www.hilti.si
Company: Trimo d.o.o. Page: 8
Address: Prijateljeva cesta 12 Specifier: Primož Kozlevčar
Phone I Fax: | E-Mail: primoz.kozlevcar@trimo-group.com
Design: DH1_Z4 Date: 7. 04. 2022
Fastening Point: DH1 Z4
7 Warnings
• The anchor design methods in PROFIS Engineering require rigid baseplates per current regulations (AS 5216:2021, ETAG 001/Annex C,
EOTA TR029 etc.). This means load re-distribution on the anchors due to elastic deformations of the baseplate are not considered - the
baseplate is assumed to be sufficiently stiff, in order not to be deformed when subjected to the design loading. PROFIS Engineering
calculates the minimum required baseplate thickness with CBFEM to limit the stress of the baseplate based on the assumptions explained
above. The proof if the rigid baseplate assumption is valid is not carried out by PROFIS Engineering. Input data and results must be
checked for agreement with the existing conditions and for plausibility!
• Checking the transfer of loads into the base material is required in accordance with EN 1992-4, Annex A!
• The design is only valid if the clearance hole in the fixture is not larger than the value given in Table 6.1 of EN 1992-4! For larger diameters
of the clearance hole see section 6.2.2 of EN 1992-4!
• The accessory list in this report is for the information of the user only. In any case, the instructions for use provided with the product have to
be followed to ensure a proper installation.
• For the determination of the y re,v (concrete edge failure) the minimum concrete cover defined in the design settings is used as the concrete
cover of the edge reinforcement.
• Load transfer from supplementary reinforcement to the structural member shall be verified by the responsible structural engineer.
• With supplementary reinforcement and post-installed anchors, please ensure that in the jobsite the rebars are not drilled through.
• The characteristic bond resistances depend on the return period (service life in years): 50
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
8
Hilti PROFIS Engineering 3.0.76
www.hilti.si
Company: Trimo d.o.o. Page: 9
Address: Prijateljeva cesta 12 Specifier: Primož Kozlevčar
Phone I Fax: | E-Mail: primoz.kozlevcar@trimo-group.com
Design: DH1_Z4 Date: 7. 04. 2022
Fastening Point: DH1 Z4
8 Installation data
2 2
Baseplate, steel: S 235; E = 210,000.00 N/mm ; fyk = 235.00 N/mm Anchor type and size: HST3 M10 hef2
Profile: no profile Item number: 2105713 HST3 M10x100 40/20
Hole diameter in the fixture: df = 12.0 mm Maximum installation torque: 45 Nm
Plate thickness (input): 4.0 mm Hole diameter in the base material: 10.0 mm
Recommended plate thickness: not calculated Hole depth in the base material: 93.0 mm
Drilling method: Hammer drilled Minimum thickness of the base material: 108.0 mm
Cleaning: No cleaning of the drilled hole is required
Hilti HST3 stud anchor with 68 mm embedment, M10 hef2, Steel galvanized, installation per ETA 98/0001
-25.0
y
45.0 45.0
335.0
335.0
1
x
335.0
335.0
20.0 70.0
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
9
Hilti PROFIS Engineering 3.0.76
www.hilti.si
Company: Trimo d.o.o. Page: 10
Address: Prijateljeva cesta 12 Specifier: Primož Kozlevčar
Phone I Fax: | E-Mail: primoz.kozlevcar@trimo-group.com
Design: DH1_Z4 Date: 7. 04. 2022
Fastening Point: DH1 Z4
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
10
Hilti PROFIS Engineering 3.0.76
www.hilti.si
Company: Trimo d.o.o. Page: 11
Address: Prijateljeva cesta 12 Specifier: Primož Kozlevčar
Phone I Fax: | E-Mail: primoz.kozlevcar@trimo-group.com
Design: DH1_Z4 Date: 7. 04. 2022
Fastening Point: DH1 Z4
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
11