Professional Documents
Culture Documents
Deogiri Institute of Engineering & Management Studies
Deogiri Institute of Engineering & Management Studies
M.S.P.M.'S
1 The line of intersection formed is straight line while two solids are intersecting the solids
may be ________
A prism, cone
B prism, cylinder
C pyramid, cone
D prism, pyramid
Ans D
2 The line of intersection formed is curve while two solids intersect the solids may be
____________
A cone, cylinder
B prism, cylinder
C pyramid, cone
D all of these
Ans D
3 Drawing straight lines on both the surfaces of solids and then pointing the points where
they intersect and drawing lines which forms the line of intersection this process of
finding the line of intersection is termed as ------------- method.
A assumption
B line
C removing material
D cutting- plane
Ans B
4 Selecting of a particular plane in a series of planes drawn cutting the solid either
parallel, perpendicular or oblique which cut the surface of one of the solids in straight
lines and that of the other in straight lines or circles. This is called ________method.
A assumption
B line
C removing material
D cutting- plane
Ans D
5 A prism and cylinder got intersected at 90 degrees the line of intersection will be ___
A straight line,
B curve
C combination of a and b
D none of these
Ans B
6 A vertical square prism is penetrated by a horizontal cylinder, it's top view would be ___
A circle and square
B square and triangle
C square and rectangle
D none of these
Ans C
7 If two cylinders of same sizes are penetrated at right angles to each other with their
axes intersecting, the curve of intersection would seem like_______
A letter c
B letter s
C letter x
D letter u
Ans C
13 If a hopper having the shape of a square pyramid is to be welded with the cylinder axially, the
intersec on would result in _____________
A curve of intersec on
B line of intersec on
C can be both A & B
D Can’t be predicted
Ans A
14 The por on of a solid which is inside an another solid is shown by thick con nuous line in the
orthographic drawing
A TRUE
B FALSE
Ans B
15 When two prisma c surfaces are intersec ng at right angles such that one being ver cal, the
lines of intersec on are seen in Top View
A TRUE
B FALSE
Ans B
16 A pentagonal pyramid would have _____ sides on base and ______ number of faces
A four, five
B five, five
C five, four
D five, one
Ans B
22 Drafters should use a ________ in a section view of a mechanical part that includes
the cylindrical view of a threaded hole.
A Center line
B Hatch line
C Poly line
D Dimension line
Ans A
23 The section view drawing in which one fourth of an object has been marked for
removal is known as a ________ section
A full
B half
C quarter
D none of the above
Ans B
26 This type of section is not in direct projection from the view containing the cutting
plane:
A Revolved section
B Removed section
C Broken-out section
D Full section
Ans B
28 In the section view, the areas that would have been in actual contact with the
cutting plane are shown with:
A A cutting plane line
B Section lining
C Visible lines
D Lines and arrows
Ans B
30 In architectural drawing ________ are often used to illustrate and detail structural
components.
A Foundation beam detail sections
B Wall sections
C Building sections
D All of the above
Ans D
31 When only a small section of an interior area needs to be revealed the drafter can
use a ________ section
A half
B quarter
C full
D broken out
Ans D
33 A ________ section allows the drafter to create a Cutting Plane line which is not in
a straight line across the part.
A Offset
B half
C whole
D broken out
Ans A
41 The angle of chamfer for hexagonal and square nut is ____ degrees as per standards.
A 30
B 45
C 60
D 90
Ans A
42 The angle through which the spanner will have to be turned to get next hold is ____
degrees in case of hexagonal shape.
A 30
B 45
C 60
D 90
Ans C
43 What is the name of the nut which can be easily operated by the thumb and a finger?
A Ring nut
B Wing nut
C Cap nut
D Flanged nut
Ans B
46 The pipe joint recommended for the system involving hot fluids like steam is
__________
A Flage joint
B Cotter joint
C Expansion joint
D none of these
Ans C
53 Which welded joint used in the circumferential joint of a cylindrical pressure vessel is
A Butt joint
B Lap joint
C Bevel joint
D none of these
Ans B
56 The name of the welded joint made by placing the plates edge to edge is called Lap
joint
A TRUE
B FALSE
Ans B
61 Drawing showing the position of each part with respect to each other is called _______
A assembly drawing
B part drawing
C machine drawing
D installation drawing
Ans A
66 Hatching lines are generally shown if cu ng plane is passing through standard parts like bolts.
A TRUE
B FALSE
Ans B
67 The part drawing must contain all the informa on required such as size and shape descrip on,
dimensions, notes, suitable material, etc.,
A TRUE
B FALSE
Ans A
69 To facilitate the manufacture of the unit, individual parts of the unit are to be produced first,
which requires the prepara on of
A assembly drawing
B part drawing
C machine drawing
D installation drawing
Ans B
70 Part list or Bill of material does not gives informa on about suitable material
A TRUE
B FALSE
Ans B
72 AUTOCAD SOFTWARE IS
A CLOUD BASED
B OFFLINE
Ans B
80 WHICH TOOL CAN BE USED TO REPEAT AN OBJECT IN NUMBER OF ROWS AND COLUMNS?
A POLAR ARRAY
B RECTANGULAR ARRAY
C CARTESSIAN ARRAY
D ALL OF THESE
Ans B
81 WHICH TOOL CAN BE USED TO JOIN LINE SEGMENTS TO MAKE A CLOSED POLYLINE?
A EXTEND
B PASTE
C BOUNDRY
D EXPLODE
Ans C
88
Which of the following workspaces are available in AutoCAD
A 3D basics
B 3D modelling
C Dra ing and Annota on
D All of these
Ans D
92 The View toolbar will position the view of the 3-D solid toward the ________.
A FRONT
B LEFT
C SE ISOMETRIC
D ALL OF THESE
Ans D
94 The default position of the UCS icon is positioned at ________ on the AutoCAD grid
A 0,0,0
B 10 , 10 , 10
C 0,1,0
D NONE OF THESE
Ans A
95 A cylinder can be created by drawing a rectangular shape then the ________ tool
A SWEEP
B REVOLVE
C EXTRUDE
D PRESS PULL
Ans B
97 In order to create one solid model from two or more separate solid shapes the dra er will need
to posi on them and then ________.
A use Union to join them
B use the Join command
C use the Add Parts tool
D none of the above
Ans A