Professional Documents
Culture Documents
CNET Communication Error (ERR - CNET - SYNC)
CNET Communication Error (ERR - CNET - SYNC)
[Meaning] When DPRAM communication is not possible between CLN[C-NET LON] [Actions to take]
and 1960 for 3 or more consecutive cycles(240ms). 1. Check LED6[Green]-CNL in DOC-200 PCB for flickering status.
(Normally, flickers at 500ms interval)
2. Turn Off and On MAIN contactor.
[Diagram] 3. Replace DOC-U50(CNL) ROM in DOC-200 PCB.
4. Replace DOC-U22 EEPROM in DOC-200 PCB.
LonDpramCntl.sync_ok[CNET] +1 err_count 5. Replace DOC-U12,13 FLASH ROM in DOC-200 PCB.
0 err_count
C-NET
LON Reset
※Communication between 1960 and CNL[C-NET LON], a kind of data communication(DPRAM WRITE)
is made through DPRAM in a TOKEN exchanging way by the TOKEN possessed side. So if TOKEN
is missed by any side, DPRM communication becomes impossible.
[Symptoms]
[Meaning] When DPRAM communication is not possible between GLN[C-NET LON] [Actions to take]
and 1960 for 3 or more consecutive cycles(240ms).
1. Check LED5[Green]-CNL in DOC-200 PCB for flickering status.
(Normally, flickers at 500ms interval)
[Diagram] 2. Turn Off and On MAIN contactor.
3. Replace DOC-U44(GNL) ROM in DOC-200 PCB.
LonDpramCntl.sync_ok[GNET] +1 err_count 4. Replace DOC-U22 EEPROM in DOC-200 PCB.
5. Replace DOC-U12,13 FLASH ROM in DOC-200 PCB.
0 err_count
G-NET
LON Reset
※Communication between 1960 and GNL[C-NET LON], a kind of data communication(DPRAM WRITE)
is made through DPRAM in a TOKEN exchanging way by the TOKEN possessed side. So if TOKEN
is missed by any side, DPRM communication becomes impossible.
[Symptoms]
ON
*Cage_Node_Down(0x7814)
Bit 7 6 5 4 3 1 2 0
[Meaning] Front Sub OPB( OPB ID = 2 ) CAR LON Communication Error [Actions to take]
1. Check the flickering status of LED6[GREEN]-CNL in
DOC-200 PCB. (Normal at 500ms interval)
2. Check the flickering status of LED-LD1in FRONT SUB OPB
side DCL-240 PCB. (Normal at 300ms interval)
[Explanation]
3. Check the input voltage between No. 4 and 3 pin of
DCL-240 PCB CCN1 connector on the side of Front SUB OPB.
(DC22V)
*Cage_Node_Down & 0x02 4. Verify if connectors for C-NET LON communicator are
S
TCD 203 connected well.
0x7814 Measure the resistance between Pin 1 and Pin 2 of Y1
connector.(If the resistance value is beyond 10±4 Ohm,
check for disconnection)
5. Check the terminal resistance (DIP SW8) setting in the
OPB side DCL-240 PCB.
(Refer to terminal resistance setting criteria)
※ CNL(C-NET LON) sends the results of communication with CLON board in each OPB to 1960 through
DPRAM, and 1960 checks the CLON board responding status by referring OPB installation SPEC and 6. Verify if OPB ID is 2(DIP 2 ‘ON’).
stores them by bit. The variable is *Cage_Node_Down(0x7814). (Refer to OPB ID setting criteria)
OPB for each Bit is shown as below. The OPB is normal if the bit is ‘0’ and is abnormal if the bit
1 2 3 4 5 6 7 8
is ‘1’.
ON
*Cage_Node_Down(0x7814)
Bit 7 6 5 4 3 2 1 0
ON
*Cage_Node_Down(0x7814)
Bit 7 6 5 4 3 2 1 0
[Meaning] Wheel Chair Sub OPB( OPB ID = 4 ) CAR LON Communication Error [Actions to take]
1. Check the flickering status of LED6[GREEN]-CNL in
DOC-200 PCB. (Normal at 500ms interval)
2. Check the flickering status of LED-LD1in WHEEL CHAIR SUB
OPB side DCL-240 PCB. (Normal at 300ms interval)
[Explanation]
3. Check the input voltage between No. 4 and 3 pin of
DCL-240 PCB CCN1 connector on the side of WHEEL CHAIR
SUB OPB. (DC22V)
*Cage_Node_Down & 0x08 4. Verify if connectors for C-NET LON communicator are
S
TCD 205 connected well.
0x7814 Measure the resistance between Pin 1 and Pin 2 of Y1
connector.(If the resistance value is beyond 10±4 Ohm,
check for disconnection)
5. Check the terminal resistance (DIP SW8) setting in the
OPB side DCL-240 PCB.
(Refer to terminal resistance setting criteria)
※ CNL(C-NET LON) sends the results of communication with CLON board in each OPB to 1960 through
DPRAM, and 1960 checks the CLON board responding status by referring OPB installation SPEC and 6. Verify if OPB ID is 4(DIP 4 ‘ON’).
stores them by bit. The variable is *Cage_Node_Down(0x7814). (Refer to OPB ID setting criteria)
OPB for each Bit is shown as below. The OPB is normal if the bit is ‘0’ and is abnormal if the bit
is ‘1’. 1 2 3 4 5 6 7 8
ON
*Cage_Node_Down(0x7814)
Bit 7 6 5 4 3 2 1 0
ON
*Cage_Node_Down(0x7814)
Bit 7 6 5 4 3 2 1 0
[Meaning] Rear Sub OPB( OPB ID = 6 ) CAR LON Communication Error [Actions to take]
1. Check the flickering status of LED6[GREEN]-CNL in
DOC-200 PCB. (Normal at 500ms interval)
2. Check the flickering status of LED-LD1in REAR SUB OPB
side DCL-240 PCB. (Normal at 300ms interval)
[Explanation]
3. Check the input voltage between No. 4 and 3 pin of
DCL-240 PCB CCN1 connector on the side of REAR SUB
OPB. (DC22V)
*Cage_Node_Down & 0x20 4. Verify if connectors for C-NET LON communicator are
S
TCD 207 connected well.
0x7814 Measure the resistance between Pin 1 and Pin 2 of Y1
connector.(If the resistance value is beyond 10±4 Ohm,
check for disconnection)
5. Check the terminal resistance (DIP SW8) setting in the
OPB side DCL-240 PCB.
(Refer to terminal resistance setting criteria)
※ CNL(C-NET LON) sends the results of communication with CLON board in each OPB to 1960 through
DPRAM, and 1960 checks the CLON board responding status by referring OPB installation SPEC and 6. Verify if OPB ID is 6(DIP 2,3 ‘ON’).
stores them by bit. The variable is *Cage_Node_Down(0x7814). (Refer to OPB ID setting criteria)
OPB for each Bit is as shown below. The OPB is normal if the bit is ‘0’ and is abnormal if the bit
is ‘1’. 1 2 3 4 5 6 7 8
ON
*Cage_Node_Down(0x7814)
Bit 7 6 5 4 3 2 1 0
[Meaning] When at least one HLON board communication is failed. [Actions to take]
1. Check errors for the SIDE, calling bell, and floor HLON board
communication by means of ANN - A21E(Back-up Ram
Referring Mode).
※ Example
[Explanation]
Enter the followings on ANN board.
Group_Net_Err_Status->Hall_Node[fl_side][I][fl_zon] K: A21E
TCD 223
ADDR:DAT K : 1040E
0x1040 If 1040=x02(0000 0010),
SIDE1,K-type calling, absolute floor 2nd floor HLON board
※ CNL(C-NET LON) sends the results of communication with HLON on each HALL side to 1960 through fault.
DPRAM, and 1960 checks the HLON board responding status by referring OPB installation SPEC and If 1040=x30(0011 0000),
stores them by bit. The variable is Group_Net_Err_Status->Node[fl_side][I][fl_zon] (0x1040). SIDE1,K-type calling, absolute floor 5,6th floor button
HALL HLON board for each Bit is as shown below. The OPB is normal if the bit is ‘0’ and the OPB is
board fault.
abnormal if the bit is ‘1’.
To see 8th or higher floor, enter KEY-PAD ‘0’(INC) on the
Group_Net_Err_Status->Node[fl_side][I][fl_zon] ANN board.
Side Side1 Side2 2. Check the failed floor for DHL-2XX board LED-LD1 flickering
부름종 Floor Address Floor Address status.(Normally, at 300ms interval)
57~64 Floor 0x105F 57~64 Floor 0x107F 3. Verify that connectors for G-NET LON are connected well.
N종 ∫ ∫ ∫ ∫ 4. Check the voltage between No. 4 and 3 pin of DHL-2XX board
1~8 Floor 0x1058 1~8 Floor 0x1078 HA plug of the failed floor. (DC22V)
57~64 Floor 0x1057 57~64 Floor 0x1077 5. Check the terminal resistance(DIP SW1 No.4) setting of
M종 ∫ ∫ ∫ ∫ DHL-2XX board on the failed side.
1~8 Floor 0x1050 1~8 Floor 0x1070 (Refer to terminal resistance setting criteria)
57~64 Floor 0x104F 57~64 Floor 0x106F 6. Check the DHL-2XX board side, calling bell, and floor ID of the failed
L종 ∫ ∫ ∫ ∫ floor. (Refer to HALL ID setting criteria)
1~8 Floor 0x1048 1~8 Floor 0x1068 7. Measure the resistance between No. 1 and 2 pin of DHL-2XX
57~64 Floor 0x1047 57~64 Floor 0x1067 board HA connector of the failed floor. If the resistance value
K종 ∫ ∫ ∫ ∫ is beyond 6 ±0.5 Ohm, pulse transformer(PST) is judged to
1~8 Floor 0x1040 1~8 Floor 0x1060 be bad.
8. Replace DOC-U50 ROM of DOC-200.
9. Replace DHL-U2 ROM in DHL-2XX of the failed floor.
[Symptoms]
•LED-LD1 in DHL-2XX board on the side of the HALL does not flicker at 300ms interval.
• All output reset, input, or output control is impossible on the side of the HALL.
Date Prepared : 98/02/18
Revision No. : 0
[Meaning] When entire HLON board communication is failed in HALL. [Actions to take]
[Symptoms]
•LED-LD1 in DHL-2XX board on the side of every HALL does not flicker at 300ms interval.
• All output reset, input, or output control is impossible on the side of every HALL.