Professional Documents
Culture Documents
ZKD Series: EN DE ES FR IT
ZKD Series: EN DE ES FR IT
ZKD Series: EN DE ES FR IT
ZKD SERIES
INSTRUCTIONS MANUAL EN
HANDBUCH DE
MANUAL DE INSTALACION ES
MANUEL D’INSTALLATION FR
MANUALE D’INSTALLAZIONE IT
When pressed during the pump operation phase, it cyclically displays the programmed values on the
display; When pressed at the same time as the keys, it increases or lowers a value
dependent on the selected operating mode. During programming it carries out an “enter” function,
meaning that it confirms entry to the various menu levels and modifications within the same.
Starts and stops the pump. In the event of a level alarm (alarm function only), flow alarm and active
memory alarm, it deactivates the signal on the display.
Used to “exit” the various menu levels. Before definitively exiting the programming phase, you will be
asked if you wish to save any changes.
Used to run upwards through the menu or increase the numerical values to be changed. Can be used
to start dosage in Batch mode
Used to run downwards through the menu, or decrease the numerical values to be changed.
Electrical connections
1
Output relay
2
3
Not connected
4
9
Flow sensor input
10
You can access the programming menu by pressing the key for over three seconds. The keys can
be used to run through the menu items, with the key being used to access changes.
The pump is programmed in constant mode in the factory. The pump automatically returns to the operating mode
after 1 minute of no activity. Any data entered in these circumstances will not be saved. The key can be used
to exit the various programming levels. Upon exiting programming, the display will show:
Exit Exit
No Save ∇ Δ Save to confirm the selection
PROG
-‐ +
Paus
Paragraph 12
Main
Paragraph 6 N.Open
Paragraph 11
Paragraph 7 Menu
Paragraph 10
Paragraph 8
Paragraph 9
Configuration
Pump Funtions
-‐ +
Paragraph 4
Setting
Menu
Paragraph 5
N.Open
Pump Functions
Paragraph 1
Manual <-
-‐ +
Functions
Menu
Pump Functions Pump Functions
Paragraph 2 Weekly Timer Paragraph 3
Timer
Pump Functions Makes it possible to select the language. The pump is set in
-‐ English in the factory.
Max flow rate
-‐
P100%
Changes can be made by pressing the key, then using
Alarm Relay
the keys to set the new value. Press to
-‐
N.Open
confirm and return to the main menu
Language
-‐ +
-‐
English
-‐
Configuration The pump operates in constant mode and the flow can only be regulated
Pump Funtions
Configuration
Pump Funtions
- +
Pump Functions
Weekly Timer
- -
1)
-
2)
Weekly Timer PROG01 MTWTFSS PROG01 hh.mm
00.00 _______ + + +
-
Time 00.00
ESC
-
3)
PROG01
+
-
Q.ty 0ml
-
4)
PROG01
+
- -
Dos.Time 0 s
-
5)
PROG01 PROG01
+
-
Rel.Off Rel.Off
6)
PROG01
Weekly
MTWTFSS
_______ - +
Clock
Wed 08:00 - + - + - +
It is possible to programme 10 dosages for the whole week. Press in the “weekly timer” mode in order to
programme the dosages.
1) The programme number can be modified using the keys and confirmed by pressing the key.
2) The dosage time can be modified using the keys and confirmed by pressing the key.
3) The dosage quantity can be set in “ml” using the keys and confirmed by pressing the key
4) The dosage time, that is to say the time (in seconds) during which you wish to dose the set quantity, can be set
5) The values of the relay connected to dosage can be modified using the keys and confirmed by
pressing the key; in “Off” mode, the relay is not switched off (open), and in “after” mode the relay closes when
dosage is activated and remains closed once dosage is completed for the time (in seconds) set using the
keys and then confirmed by pressing the key. In “before” mode, the relay closes before the dosage activation
time, for the time (in seconds) set using the keys and then confirmed by pressing the key.
6) Day activation, or rather the days on which you want the set programme to be active (start time, quantity,
dosage duration and relay operating mode). Press the key to make changes, then press the key to
activate/deactivate dosage and the key to change the day of the week. Press to confirm and move
automatically to the next programme.
Repeat the whole procedure if you need to programme the new programme, or press to return to the main
menu.
The next step in the main menu is programming the clock. This can be done by pressing the to make
changes, using the to set the required values and then confirming by pressing the key. You can set
the day, hour and minutes in sequence. Obviously, the set time and day are those that the programming will refer
to.
Hayward Flow Control www.haywardflowcontrol.com 1-888-INDL (1-888-429-4635)
ZKDIOM
Pg. 4 of 10
Display during Operation Display during Setting (MODE key)
FLOW Operating mode
sensor • Day of the week • Displays in sequence:
Operating mode status Displays the quantity during programme number, activation
• Weekly timer dosages time, quantity, dosage time,
relay status.
Weekly FF Mon •
Lev Stop 12.01 Day of the
Time P01:START Mon week
Alarms and statuses
• Displays hours 14.40 12.01
• Lev = Level alarm and minutes
• Flw = Flow alarm Pump status
• Mem = Memory alarm • Empty = pump in start
• Stop = pump stationary Time
• Displays hours and minutes
• Paus = pump in pause
PROG
Trigger Quantity
Configuration
Configuration
Pump functions
Delay Interv.
- +
By setting for example an Interval. time = 0, a system is
Pump functions
Time obtained in which the programmed quantity is dosed after each
TRIGGER signal (with any delay that has been set):
Time
- + Trigger Release
-
Quantity 100ml
Time g.hh.mm
- +
-
Delay 0.01.50
Time g.hh.mm
- +
Delay Ritardo
-
interv. 0.01.50
- Trigger Mode
Disable
The Trigger signal is locked during dosing (its receipt is neither
stored nor managed).
The Pause (Remote input) input cannot be programmed and
Relay
- +
its activation stops the dosing, while its further deactivation
-
Off makes the system wait again for the Trigger signal for a new
dosing.
Configuration
Pum functions
- + Delay Interv.
Pum functions
Tempo
The Delay and Interval times are in dd.hh.mm (days, hours, minutes)
Time
- +
-
Quantity 100ml
-
Freeze Time
Relay
- +
frequency or the keys to decrease it.
- The values of the relay connected to dosage can be modified using the
Off
for the time (in seconds) set using the keys and then confirmed
dosage activation time, for the time (in seconds) set using the
-‐
P100%
-‐ MANUAL – manually enter the cc value per strike using the
Pump Calibration
0,23 cc/stroke
keys and confirm by pressing the key
AUTOMATIC – the pump makes 100 strikes, which are
Pump Calibration
Manual
Pump Calibration
cc/stroke 0,23 -‐ + started by pressing the key. At the end of this process,
-‐ enter the quantity sucked up by the pump using the
Pump Calibration Automatic Cal.
Automatic Start 100 strok.
keys and confirm by pressing the key.
Automatic Cal.
ml 20 -‐ +
Paragraph 7 - Statistics
Programming Operation
PROG
-‐
-‐ The main menu displays the pump operation times. By
Statistic
Hours 10 pressing the key you can access other statistics:
- Strokes = number of strokes made by the pump
Statistic - Q.ty (L) = quantity dosed by the pump in litres; this figure is
Strokes 1000
calculated on the basis of the memorised cc/stroke value
-‐ - Power = number of pump starts
Statistic
-‐
Q.ty(L) 100
- Reset = use the to reset the counters (YES) or
Statistic
Power 10
otherwise (NO), then confirm by pressing the key.
-‐
Statistic
Reset
Statistic Reset
NO -‐ +
ESC
Pressing the key will take you back to the main menu.
Statistic
-‐
Hours 10
Paragraph 8 – Password
Programming Operation
P RO G
By entering the password, you can enter the programming
menu and see all the set values. The password will be
-‐ requested whenever you seek to modify them.
The flashing line indicates the number than can be modified.
-‐ Use the key to select the number (from 1 to 9), and the
P a ss w o rd
* * **
-‐
Flow Off
ESC
Alarms pressing the key. Press to return to the main
Level Alarm
-‐ menu
-‐ -‐
N.Aperto
using the keys to set the new value ( N. OPEN or
N. CLOSED).
For adjusting the display contrast keep the key pressed and within 5 seconds press the keys or to
increase or decrease the contrast.
Alarms
Display Cause Interruption
Fixed alarm LED End of level alarm, without Restore the liquid level.
Flashing word “Lev” interrupting pump operation
I.e. Man
Lev P100%
Fixed alarm LED End of level alarm, with interruption Restore the liquid level.
Flashing words “Lev” and “stop” to pump operation
I.e. Man
Lev Stop P100%
Fixed alarm LED Active flow alarm. The pump has
Flashing word “Flw” not received the programmed Press the key
I.e. Man F number of signals from the flow
Flw P100% sensor.
Internal CPU communication error.
I.e. Parameter Error Press the key to restore the
PROG to default default parameters.
Während des Pumpenbetriebs: Durch Drücken werden die programmierten Werte zyklisch auf dem
Display angezeigt; bei gleichzeitigem Drücken der Tasten wird ein Wert, je nach
ausgewähltem Betriebsmodus, erhöht bzw. verringert. Während der Programmierung übernimmt
diese Taste die Funktion “Enter”, d.h. dass der Zugriff auf die verschiedenen Menüstufen und die dort
vorgenommenen Veränderungen bestätigt werden.
Startet und stoppt die Pumpe. Wenn ein Füllstandsalarm (nur Alarmfunktion), ein Durchflussalarm
und ein Memoryalarm aktiv ist, deaktiviert diese Taste die Anzeige auf dem Display.
Zum “Verlassen” der verschiedenen Menüstufen. Vor dem endgültigen Verlassen der Programmierung,
öffnet sich ein Speicherungsdialog für Veränderungen.
Blättert nach oben im Menü, oder erhöht die numerischen Werte, die verändert werden sollen. Im
Batch-Modus kann diese Taste die Dosierung starten.
Blättert nach unten im Menü, oder verringert die numerischen Werte, die verändert werden sollen.
Anschlusse Elektrik
1 Relaisausgang (Alarm)
Wahlweise Öffner (NC)
2 oder Schliesser (NO)
3
Nicht verwendet
4
3 4 5 6 5 -Eingang
2 Fernbedienung(Start-Stop)
-Eingang Pause-signal
1 6
9
Eingang Fluss - Sensor
10
B Eingang Füllstandkontrolle
Durch über drei Sekunden langes Drücken der Taste erhalten Sie Zugriff auf die Programmierung. Über die
Tasten können Sie die Menüpunkte durchblättern. Über die Taste erhalten Sie Zugriff auf die
Veränderungen.
Werkseitig ist die Pumpe auf den Konstant-Modus programmiert. Die Pumpe kehrt nach 1 Minute Inaktivität
automatisch zum Betriebs-Modus zurück. In diesem Fall werden etwaig eingegebene Daten nicht gespeichert.
Über die Taste verlassen Sie die Programmierstufen. Bei Verlassen der Programmierung wird auf dem
Display folgendes angezeigt:
Exit Exit
∇ Δ Zur Bestätigung der
No Save Save
Auswahl
PROG
Konfiguration
-‐ +
Paus
Pumpen-Kalib Absatz 12
Absatz 6 N.Offen
Hube
Hauptmenü Einheit
Absatz 11
Statistik
Absatz 7
Stunden
Absatz 10
Passwort
Absatz 8
Absatz 9
Fluss
Konfiguration
Pumpen funktionen
-‐ +
Sprache
Absatz 4
Max Fluss Rate Menü Deutsch
Einstellungen
Absatz 5
N.Open
Pumpen funktionen
Absatz 1
Manuell <-
-‐ +
Menü
Funktionen
Pumpen funktionen Pumpen funktionen
Absatz 2 Absatz 3
Wochen Timer Timer
-‐
N.Open
den Wert ein. Über bestätigen Sie und werden zum
Language
-‐ +
Hauptmenü zurückgeleitet
-‐
English
-‐
Absatz 1 – Manuelle Dosierung
Programmierung Funktionsweise
PROG
Konfiguration
Konfiguration
Konfiguration
Pumpen funktionen
- +
Pumpen funktionen
Wochen Timer
- -
1)
-
2)
Wochen-Timer PROG01 MTWTFSS PROG01 hh.mm
00.00 _______ + + +
-
Zeit 00.00
ESC
-
3)
PROG01
+
-
Menge 0ml
-
4)
PROG01
+
- -
Dos.Zeit 0 s
-
5)
PROG01 PROG01
+
-
Rel.Off Rel.Off
6)
PROG01
Wochen
MTWTFSS
_______ - +
Uhr
Mit 08:00 - + - + - +
Es können 10 Dosierungen für die gesamte Woche programmiert werden. Durch Drücken von vom “weekly
timer” erhalten Sie Zugriff auf die Programmierung der Dosierungen.
1) Programmnummer, kann über die Tasten verändert werden und wird über bestätigt.
2) Uhrzeit der Dosierung, kann über die Tasten verändert werden und wird über bestätigt.
3) Dosiermenge, über die Tasten wird der Wert in “ml” eingegeben und über bestätigt.
4) Dosierzeit, d.h. in welchem Zeitraum (in Sekunden) die zuvor programmierte Menge dosiert werden soll, über
die Tasten wird der Wert in “ml” eingegeben und über bestätigt.
5) Einstellung des mit der Dosierung verbundenen Relais, über die Tasten werden die Werte verändert
und über bestätigt; im “Off”-Modus bleibt das Relais nicht ausgeschaltet (geöffnet), im “After”-Modus schließt
sich das Relais, wenn die Dosierung aktiviert wird und bleibt nach beendeter Dosierung für den Zeitraum (in
Sekunden) geschlossen, der über die Taste eingegeben wird, anschließend durch Drücken von
bestätigen. Im “Before”-Modus schließt sich das Relais bevor die Dosierung aktiviert wird, für einen Zeitraum (in
Sekunden), der über die Tasten eingestellt wird, anschließend durch Drücken von bestätigen.
6) Aktivierung der Tage, d.h. die Tage, an denen das eingegebene Programm (Startzeit, Menge, Dosierdauer und
Betriebsmodus des Relais) aktiv sein soll. Über erhalten Sie Zugriff auf die Veränderungen, über die Taste
wird die Dosierung aktiviert/deaktiviert und über die Taste wird der Wochentag geändert. Durch Drücken
von bestätigen Sie und werden automatisch zum nachfolgenden Programm weitergeleitet.
Wenn das neue Programm programmiert werden soll, wiederholen Sie die zuvor aufgeführten Verfahrensschritte,
Im Hauptmenü ist der nächste Schritt die Programmierung der Uhr. Durch Drücken der Taste erhalten Sie
Zugriff auf die Veränderungen. Geben Sie über die Tasten die Werte ein und bestätigen Sie durch
Drücken von . So können der Reihe nach der Tag, die Uhrzeit und die Minuten eingegeben werden. Natürlich
wird die Programmierung auf den eingestellten Tag und die eingestellte Uhrzeit Bezug nehmen.
Hayward Flow Control www.haywardflowcontrol.com 1-888-INDL (1-888-429-4635)
ZKDIOM
Pg. 4 of 10
Anzeige während der Einstellung (Taste
Anzeige während des Betriebs
MODE)
Zustand des • Wochentag Betriebs-Modus
Betriebs-Modus Durchflusssensors Während der Dosierungen • Der Reihe nach werden angezeigt:
• Weekly timer wird die Menge angezeigt Programmnummer, Startzeit, Menge,
Dosierdauer, Relaiszustand
Weekly F Mon
Lev Stop 12.01 Uhrzeit Wochentag
Alarme und Zustände • Zeigt Stunden P01:START Mon
• Lev = Füllstandsalarm 14.40 12.01
• und Minuten an
Flw = Durchflussalarm Zustand der Pumpe
• Mem = Memoryalarm • Leer = Pumpenstart
• Stop = Pumpe steht Uhrzeit
• Pause = Pumpe in Pause • Zeigt Stunden und Minuten an
Trigger Menge
PROG
Trigger Trigger
Zeit
- +
-
Menge 100ml
Zeit g.hh.mm
- +
-
Verzog. 0.01.50
Zeit g.hh.mm
- +
Verzögerung Verzögerung
-
Interval 0.01.50
Konfiguration
Menge
Pumpen funktionen
- +
Pumpen funktionen
Zeit
Verzögerung
Interv.
Zeit
- +
-
Menge 100ml
Die Verzögerungs- und Pausenzeiten sind in T/S/M (Tage, Stunden,
Zeit g.hh.mm
- +
Minuten) angegeben.
-
Verzog. 0.01.50
Zeit g.hh.mm
- +
Der Pausen-Eingang kann auf drei unterschiedliche Arten
-
Interval 0.01.50
programmiert werden:
Trigger Modus
- + 1. Blocki Zeit: Bei aktivierter Pause blockiert das System die
-
gesperrt
Zählung der aktuellen Zeit und nimmt sie wieder auf, wenn die
Pause Eingabem. Pause Eingabem.
Pause deaktiviert wird.
-
Time neu start. Time neu start.
-
Block Zeit
3. Time neu start.: Bei aktivierter Pause blockiert das System
Pause Eingabem. die Dosierung und startet die Zählung neu, wenn die Pause
Dosierpause
deaktiviert wird.
Relais
- +
Während des Pumpenbetriebs kann die Dosierfrequenz verändert
-
Off
Alarm Relay
-‐ + den Wert ein. Über bestätigen Sie und werden zum
-‐ -‐
N.Open
Hauptmenü zurückgeleitet.
Pumpen Kalib
Manuell
Pumpen Kalib
Cc/hub 0,23 -‐ +
die Taste gestartet werden. Wenn diese Hübe
Absatz 7 – Statistiken
Programmierung Funktionsweise
PROG
-‐
Menge(L) 100
zurück.
Absatz 8 – Passwort
Programmierung Funktionsweise
P RO G Durch Eingabe des Passworts erhalten Sie Zugriff auf die
Konfiguration
Programmierung und können sich alle eingegebenen Werte
-‐ ansehen. Jedes Mal wenn Sie versuchen, diese Werte zu
verändern, erscheint ein eigener Passwortdialog.
Die blinkende Linie zeigt die veränderbare Nummer an.
Passwort
-‐
* * ** Wählen Sie über die Taste die Nummer aus (zwischen
Passwort
0000 + -‐ 1 und 9), wählen Sie über die Taste die Nummer aus,
die verändert werden soll, und bestätigen Sie anschließend
-‐
über . Durch Eingabe von “0000” (Default) wird die
Passwortabfrage übersprungen.
Konfiguration
Ermöglicht die Aktivierung (Deaktivierung) des
-‐ Durchflusssensors.
Wenn er einmal aktiviert ist (ON), erhalten Sie durch
-‐ Drücken der Taste Zugriff auf den Abfragedialog, wie
Alarm Alarm Fluss
+
Alarm Fluss
On auslöst. Durch Drücken von beginnt die Nummer zu
-‐ -‐ blinken. Stellen Sie dann über die Tasten den
Alarm Fluss - On
Signale 6 -‐ +
ESC Wert ein. Über bestätigen Sie. Durch Drücken von
werden Sie zum Hauptmenü zurückgeleitet.
-‐
Fluss Off
Absatz 10 – Füllstandsalarm
Programmierung Funktionsweise
PROG
Konfiguration
Ermöglicht die Einstellung des Zeitpunkts, an dem der
-‐ Füllstandsalarm aktiviert wird, also auch ob die Dosierung
blockiert (Stop), oder einfach nur das Alarmsignal aktiviert
werden soll, ohne dabei die Dosierung zu blockieren.
-‐
Alarm Alarm Level Durch Drücken von erhalten Sie Zugriff auf die
-‐
Level Stop Stop
Einheit
-‐ Einheit Veränderung. Stellen Sie dann über die Tasten
die gewünschte Maßeinheit ein, L/H (Liter/Stunde), GpH
Standard Standard <-
-‐ +
(Gallone/Stunde), ml/m (Milliliter/Minute) oder die
-‐ Einheit
L/h
Standardeinstellung (% oder Frequenz, je nach Einstellung).
-‐ Über bestätigen Sie und werden zum Hauptmenü
zurückgeleitet.
-‐ -‐
N.Offen
Veränderung.
Stellen Sie dann über die Tasten den Wert ein (N.
OFFEN oder N. GESCHLOSSEN).
zurückgeleitet.
Für die Einstellung des Display-Kontrasts wird die Taste festgedrückt und innerhalb von 5 Sekunden mit den
Alarme
Anzeige Ursache Unterbrechung
Alarm-Led leuchtet kontinuierlich Alarm Füllstand nicht ausreichend, Flüssigkeit nachfüllen
Der Schriftzug Lev blinkt ohne Unterbrechung des
Bsp.: Man Pumpenbetriebs
Lev P100%
Alarm-Led leuchtet kontinuierlich Alarm Füllstand nicht ausreichend, Flüssigkeit nachfüllen
Der Schriftzug Lev und Stop blinkt mit Unterbrechung des
Bsp.: Man Pumpenbetriebs
Lev Stop P100%
Alarm-Led leuchtet kontinuierlich Durchflussalarm aktiv, die Pumpe
Der Schriftzug Flw blinkt hat nicht die programmierten Die Taste drücken
Bsp.: Man F Signale vom Durchflusssensor
Flw P100% empfangen.
Interner Kommunikationsfehler der
Bsp.: Parameter Error CPU. Die Taste drücken, um auf die
PROG to default Default-Parameter rückzustellen.
Para “salir” de los diferentes niveles del menú. Antes de salir definitivamente de la
programación se accede a la solicitud de memorización de las modificaciones.
Desplaza los menús hacia arriba o incrementa los valores numéricos a modificar. En modo Batch
puede poner en marcha la dosificación.
Desplaza los menús hacia abajo o disminuye los valores numéricos a modificar.
Conexiones eléctricas
1
Relé de Alarma
2
3
No permitido
4
5
-Entrada control externo (start-stop)
B -Entrada señal de pausa
6
7
Entrada trigger externo
8
9
Entrada sensor de Flujo
10
Pulsando la tecla durante más de tres segundos se accede a la programación. Con las teclas se
pueden desplazar las voces del menú, con la tecla se accede a las modificaciones. En la fábrica la bomba se
programa en modo constante. La bomba vuelve automáticamente al modo de funcionamiento después de 1
minuto de inactividad. En este caso los datos que se han introducido no serán memorizados. Con la tecla se
sale de los niveles de la programación. Al salir de la programación el display visualiza:
Exit Exit
No Save ∇ Δ Save para confirmar la elección
PROG
Configuracion
-‐ +
Paus
Calib. Bomba N.Abierto Párrafo 12
Párrafo 6
0,23 cc/imp
Menú Unidades
Párrafo 11
Párrafo 7
Statisticas principal
Horas= ###,## Alarmas
Párrafo 10
Nivel Off
Párrafo 8 Alarmas
Párrafo 9
Caudal Off
Configuracion
Funciones Bomba
-‐ +
Caudal maximo
Menú Idioma
Párrafo 4
de ajustes Espagnol
Párrafo 5 Rele Alarma
Abierto
Funciones Bomba
Párrafo 1
-‐ +
Menú
de funciones
Funciones Bomba Funciones Bomba
Párrafo 2 Párrafo 3
Temp.Semanal Temporizacion
-‐
N.Open
Con la tecla se confirma y se vuelve al menú principal.
Language
-‐ +
-‐
English
-‐
Configuracion
Configuracion
Configuracion
Funciones Bomba
- +
Funciones Bomba
Dos.settimanale
- -
1)
-
2)
Dos.settimanale PROG01 LMMJVSD PROG01 hh.mm
00.00 _______ + + +
-
Hora 00.00
ESC
-
3)
PROG01
+
-
Cantidad 0ml
-
4)
PROG01
+
- -
Tiempo dos. 0 s
-
5)
PROG01 PROG01
+
-
Rel.Off Rel.Off
6)
PROG01
Dia
LMMGVSD
_______ - +
Reloj
Mar 08:00 - + - + - +
Se pueden programar diez dosificaciones para toda la semana. Pulsando la tecla del “weekly timer” se
accede a la posibilidad de programar las dosificaciones.
1) Número del programa, con las teclas se modifica y con la tecla se confirma.
3) Cantidad a dosificar, con las teclas se programa el valor en “ml” y con la tecla se confirma.
4) Tiempo de dosificación, es decir, en cuánto tiempo (segundos) se quiere dosificar la cantidad programada
anteriormente, con las teclas se programa el valor en “ml” y con la tecla se confirma.
5) Programación del relé conectado con la dosificación, con las teclas se modifican los valores y con la
tecla se confirman; en modo OFF el relé no se queda apagado (abierto), en modo “after” el relé se cierra al
momento de la activación de la dosificación y se queda cerrado una vez terminada la dosificación durante el
tiempo (en segundos) programable con las teclas ; confirmar con la tecla . En modo “before” el relé
se cierra antes del tiempo de activación de la dosificación, durante un tiempo (en segundos) programable con las
inicio, cantidad, duración de la dosificación y modo de funcionamiento del relé). Con la tecla se accede a las
modificaciones, con la tecla se activa/desactiva la dosificación, con la tecla se puede cambiar el día de
programar el nuevo programa repetir el procedimiento anterior, de lo contrario pulsar la tecla para volver al
menú principal. En el menú principal el paso sucesivo es la programación del reloj, pulsando la tecla se
accede a las modificaciones, con las teclas se programan los valores y con la tecla se confirman.
En secuencia se pueden programar el día, la hora y los minutos. Obviamente el día y el horario programados son
aquellos a los que hará referencia la programación.
Hayward Flow Control www.haywardflowcontrol.com 1-888-INDL (1-888-429-4635)
ZKDIOM
Pg. 4 of 10
Visualización durante el funcionamiento Visualización en programación (tecla MODE)
Estado del • Día de la semana Modo de funcionamiento
sensor de Durante las dosificaciones • Visualiza en secuencia: el número
Modo de funcionamiento FLUJO visualiza la cantidad del programa, la hora de activación,
• Weekly timer la cantidad, el tiempo de
dosificación y el estado del relé.
Weekly FF Mon
Lev Stop 12.01 • Día de la
Horario P01:START Mon semana
Alarmas y estados
• Visualiza horas 14.40 12.01
• Lev = Alarma de nivel y minutos
• Flw = Alarma de flujo Estado de la bomba
• Mem = Alarma Memory • Vacío = bomba en start
• Stop = bomba parada Horario
• Pausa = bomba en pausa • Visualiza horas y minutos
Trigger Cantidad
PROG
Configuracion
Configuracion
Funciones Bomba Retardo Interv.
Tiempo g.hh.mm
- +
-
Retardo 0.01.50
Tiempo g.hh.mm
- + Retardo Retardo
-
Interval 0.01.50
-
Off
programada y su activación bloquea la dosificación, mientras que la
siguiente desactivación vuelve a poner el sistema en estado de
espera de la señal Trigger para efectuar una nueva dosificación.
Configuracion
Cantidad
Configuracion
Funciones Bomba
- +
Retardo Interv.
Funciones Bomba
Tiempo
Tiempo
- +
Los tiempos de Retardo y de Interv son en d.h.m. (días, horas, minutos).
-
Quantita 100ml
- pausa.
Interval 0.01.50
Rele
- +
aumentar la frecuencia o las teclas para disminuirla.
-
Off
Timer F 7,0 ml
Liv Stop P 0% Valor de la Valor de la
• Alarmas y estados Niv = dosificación
dosificación en curso Q.tà 20,0ml •
Alarmas nivel Cantidad
Estado de la bomba • Porcentaje de 20,0ml P 100%
programada en
• Flujo = Alarma control
• Vacío = bomba en start los golpes/min. ml
de flujo
• Stop = bomba en parada máx Valor del porcentaje de
• Reiniciar = bomba en dosificación modificable pulsando
rearranque las teclas + o -
Configuracion
Permite programar el caudal máximo que la bomba puede
alcanzar; el modo programado (% o frecuencia) se vuelve la
Configuracion
visualización del caudal en la unidad de medida estándar.
Funciones Bomba
Configuracion
Sirve para programar el relé de alarma en ausencia de una
Configuracion situación de alarma, si está abierto (default) o cerrado.
Funciones Bomba
-‐
P100%
con las teclas se programa el valor. Con la tecla
Rele alarma
-‐ +
se confirma y se vuelve al menú principal.
-‐ -‐
Abierto
Párrafo 7 - Stadísticas
Programación Funcionamiento
PROG
Configuracion
En el menú principal visualiza las horas de funcionamiento
-‐
de la bomba, pulsando la tecla se accede a las demás
-‐ estadísticas:
Statisticas
Horas 10 - Strokes = Número de golpes realizados por la bomba.
Statisticas
- Q.ty (L) = Cantidad dosificada por la bomba expresada en
Inyecciones 1000 litros; este valor se calcula en base al valor cc/stroke en
-‐ memoria.
Statisticas
- Power = Número de puestas en marcha de la bomba.
-‐
Cant.(l) 100
-‐
Statisticas
Reset
Reset Estat.
NO -‐ + (YES) o no (NO) los contadores, con la tecla se
ESC
Párrafo 8 - Password
Programación Funcionamiento
P RO G Introduciendo la password se puede entrar en programación
Configuracion y ver todos los valores programados, pero para modificarlos
-‐ será solicitada la password. La línea parpadeante indica el
Configuracion
Permite activar (desactivar) el sensor de flujo. Una vez
-‐
activado (ON) pulsando la tecla se accede a la solicitud
-‐ de cuántas señales espera la bomba antes de entrar en
Alarma Alarma Caudal
Caudal Off
-‐
Off
Configuracion
Permite programar la bomba cuando se activa la alarma del
-‐ sensor de nivel, es decir se bloquea la dosificación (Stop) o
simplemente activa la señal de alarma sin bloquear la
-‐ dosificación. Pulsando la tecla se accede a la
Alarma Alarma Nivel
Nivel Stop
-‐
Stop
-‐ -‐
N.Abierto
Para ajustar el contraste del display mantener presionada la tecla y dentro de 5 segundos presionar las teclas
Alarmas
Visualización Causa Interrupción
Alarma de final del nivel sin Reestablecer el nivel del líquido.
Led Alarma fijo interrupción del funcionamiento de
Mensaje Lev parpadeante la bomba.
Ej: Man
Lev P100%
Led Alarma fijo Alarma de final del nivel con Reestablecer el nivel del líquido.
Mensajes Lev y stop parpadeantes interrupción del funcionamiento de
Ej: Man la bomba.
Lev Stop P100%
Alarma de flujo activa, la bomba no
Led Alarma fijo ha recibido el número de señales Pulsar la tecla
Mensaje Flw parpadeante programadas por el sensor de flujo.
Ej: Man F
Flw P100%
Error de comunicación interna de la
Ej: Parameter Error CPU. Pulsar la tecla para
PROG to default reestablecer los parámetros de
default.
Pendant la phase de fonctionnement de la pompe: si cette touche est enfoncée elle affiche à des
intervalles réguliers les valeurs programmées; si elle est enfoncée en même temps que les touches
Pour “quitter” ces différents niveaux de menu. Avant de quitter définitivement la programmation, on
accède à la demande d’enregistrement des modifications
Fait défiler les menus vers le haut ou augmente les valeurs numériques à modifier. En mode de
fonctionnement Batch, elle peut faire démarrer le dosage.
Fait défiler les menus vers le bas, ou réduit les valeurs numériques à modifier.
Connexions électriques
1
Relais Alarme
2
3
Pos utilisè
4
3 4 5 6 5 -Entrée commande à
distance (start-stop)
2 6 -Entrée Pausa signal
1
7
Entrée Detente externo
8
B 7 8 9 10
9
Entrée capteur de débit
10
Appuyer sur la touche pendant plus de trois secondes pour allumer la programmation. Avec les touches
il est possible de faire défiler les options du menu, la touche permet d’accéder aux modifications.
La pompe est programmée en usine en mode constant. La pompe reprend automatiquement le mode de
fonctionnement après 1 minute de non-activité. Dans ce cas, les données éventuellement introduites ne sont pas
enregistrées.
PROG
-‐ +
Paus Paragraphe 12
Calibrage pompe
Paragraphe 6 N.Ouvert
coup
Unite
Paragraphe 11
Statistiques
Paragraphe 7 Heures
Alarmes
Paragraphe 10
Niveau
Code d'acces
Paragraphe 8 Alarmes
Paragraphe 9
Debit
Configuration
Fonction pompe
-‐ +
Debit Max Menu Langage
Paragraphe 4 Francais
réglage
Contact d'alarme
Paragraphe 5 N.O.
Fonction pompe
Paragraphe 1
Manuel
-‐ Menu
+
fonction
Fonction pompe Fonction pompe
Paragraphe 2 Paragraphe 3
Temps Hebdo Temps
Pump Functions
Permet de sélectionner la langue, la pompe est programmée
-‐ en usine en anglais.
Max flow rate
Appuyer sur pour accéder à la modification, puis sur
-‐
P100%
-‐
Configuration
Fonction pompe La pompe travaille en mode constant et le débit peut être réglé uniquement
-‐ +
en mode manuel en appuyant simultanément sur les touches
Fonction pompe
Manuel
pour augmenter le débit ou sur les touches pour le réduire.
Configuration
Fonction pompe
- +
Fonction pompe
Temps Hebdo
- -
1)
-
2)
Temps Hebdo PROG LMMJVSD PROG01 hh.mm
00.00 _______ + + +
-
Temp 00.00
ESC
-
3)
PROG01
+
-
Quantite 0ml
-
4)
PROG01
+
- -
Temps Dos 0 s
-
5)
PROG01 PROG01
+
-
Rel.Off Rel.Off
6)
PROG01 MTWTFSS
Hebdomadaire____ - +
Horloge
Mer 08:00 - + - + - +
Il est possible de programmer 10 dosages pour toute la semaine. Appuyer sur à partir de “weekly timer” pour
accéder à la possibilité de programmer les dosages. .
1) Numéro du programme, avec les touches il est possible de le modifier et avec il est confirmé.
2) Horaire du dosage, avec les touches il est possible de le modifier et avec il est confirmé.
5) Programmation du relais connecté au dosage, les touches permettent de modifier les valeurs et la
touche les confirme; en mode “Off” le relais ne reste pas allumé (ouvert), en mode “after” le relais se ferme au
moment de l’activation du dosage et il reste fermé lorsque le dosage est terminé pendant le temps (en secondes)
qui est programmé avec les touches , pour confirmer appuyer sur . En mode “before” le relais se
ferme avant le temps d’activation du dosage, pendant un temps (en secondes) qui est programmé avec les
actif (heure de départ, quantité, durée du dosage et mode de fonctionnement relais). La touche permet
d’accéder aux modifications, puis avec la touche il est possible d’activer et de désactiver le dosage, avec la
touche il est possible de changer le jour de la semaine. Appuyer sur pour confirmer et passer
automatiquement au programme suivant.
Pour programmer un nouveau programme répéter la procédure précédente, sinon appuyer sur pour retourner
au menu principal.
Dans le menu principal, l’étape suivante est la programmation de l’horloge, appuyer sur pour accéder aux
modifications, avec les touches programmer les valeurs puis confirmer en appuyant sur . Il est
possible de programmer le jour, l’heure et les minutes dans cet ordre. Naturellement, le jour et l’horaire
programmés sont ceux auxquels la programmation fait référence.
Hayward Flow Control www.haywardflowcontrol.com 1-888-INDL (1-888-429-4635)
ZKDIOM
Pg. 4 of 10
Affichage lors de la programmation (touche
Affichage pendant le fonctionnement
MODE)
État capteur Mode de fonctionnement
de FLUX • Jour de la semaine • Affiche dans l’ordre: numéro
Mode de fonctionnement Durant les dosages affiche la du programme, heure
• Weekly timer
quantité d’activation, quantité, temps
de dosage, état du relais.
Weekly F Mon •
Lev Stop 12.01 Jour de la
Horaire P01:START Mon semine
Alarmes et états • Affiche heures
• 14.40 12.01
Lev = Alarme niveau et minutes
• Flw = Alarme fluxage État de la pompe
• • Vide=pompe au démarrage
Mem = Alarme Mémoire
• Stop = pompe arrêtée Horaire
• Paus = pompe en pause • Affiche heures et minutes
Configuration
Function pompe
Retard Interv.
- +
En réglant, par exemple, un temps Interv. = 0 on obtient
Function pompe
Temps un système dosant la quantité programmée après chaque
signal de DETENTE (avec l’éventuel retard réglé):
Temps
- + Detente Detente
-
Quantite 100ml
Temps g.hh.mm
- +
-
Retard 0.01.50
Retard Retard
Temps g.hh.mm
- +
-
Interval 0.01.50
Il est possible de faire démarrer le dosage même en
Mode detente Mode detente
appuyant sur la touche +, simulant pratiquement le signal
de Detente.
- -
N.O. N.O.
Le signal Detente peut être réglé NO (il s’active lorsque
l’entrée passe du mode ouvert au mode fermé) ou NF (il
Entree Pause Mode detente
s’active lorsque l’entrée passe du mode fermé au mode
-
Mode detente N.F.
ouvert).
- Mode detente
Desaffecte’
Le signal Detente est bloqué pendant le dosage (son
arrivée n’est ni mémorisée ni gérée).
L’entrée Pause (Entrée commande à distance) ne peut
-
pas être programmée et son activation bloque le dosage,
Contact
+ tandis que la désactivation successive remet le système
-
Off
en attente du signal Detente pour un nouveau dosage.
Pendant la phase de fonctionnement de la pompe, il est
possible de modifier la fréquence du dosage, en appuyant
Mode de fonctionnement
Etat capteur • Visualise en séquence:
de FLUX
Mode de fonctionnement Valeur programmée quantité à doser, retard en
• Temps • Quantité en ml j.hh.mm et interval en
j.hh.mm
Temps F 7.0ml
Stop P 0% Valeur du dosage
Valeur du dosage en • Quantité
Alarmes et états cours
Q.té 20.0ml
• Niv = Alarme niveau • Pourcentage des 20.0ml P 100% programmée en
• Deb = Alarme fluxage Etat de la pompe ml
• coups/min max
• ou = Attente Detente Vide = pompe en start
• Stop = pompe arrêtée
• Réinitialiser = pompe en Valeur du pourcentage du dosage,
restart en appuyant sur les touches + ou –
on le modifie
Quantite
PROG
Configuration
Retard Interv.
Configuration
Function pompe
Les temps de Retard et Interv. sont en jj.hh.mm
(jours.heures.minutes)
- +
L’entrée Pause peut être programmée en trois modes
Function pompe
Temps différents:
-
1. Blocage du temps: avec la pause activée, le
Temps
+ système bloque le comptage du temps actuel
-
Quantite 100ml
qui reprend quand la pause se désactive
-
2. Pause Dosage: avec la pause activée, le
Temps g.hh.mm
+ système continue à compter le temps et bloque
-
Retard 0.01.50
le dosage
-
3. Redemarr. Temp: avec la pause activée, le
Temps g.hh.mm
+ système bloque le dosage, quand la pause se
-
Interval 0.01.50
désactive le comptage recommence dès le
-
début.
Mode detente
+
-
Desaffecte’
Pendant la phase de fonctionnement de la pompe, il est
Entree Pause
possible de modifier la fréquence du dosage, en
Entree Pause
-
Redemarr. Temp Redemarr. Temp
appuyant en même temps sur les touches
pour augmenter la fréquence, ou bien sur les touches
-
Entree Pause
-
Blocage du temps
pour la diminuer.
Programmation du relais connecté au dosage, les
Entree Pause
Pause Dosage
touches permettent de modifier les valeurs et
Contact
- +
-
Off
la touche les confirme; en mode “Off” le relais ne
reste pas allumé (ouvert), en mode “after” le relais se
ferme au moment de l’activation du dosage et il reste
fermé lorsque le dosage est terminé pendant le temps
(en secondes) qui est programmé avec les touches
appuyer sur .
-‐
P100%
ESC
Statistiques La pression de permet de retourner au menu principal.
-‐
Heures 10
Alarmes
-‐ Une fois activé (On) appuyer sur la touche
accéder à la demande de combien de signaux la pompe
pour
Alarme Debit
attend avant de déclencher l’état d’alarme. En appuyant sur
-‐
Debit Off Off
+
Alarme Debit
On le nombre clignote, puis avec les touches
-‐
Debit Off
-‐
Niveau Stop Stop
-‐ +
(millilitres/minute) ou standard (% ou fréquence selon la
-‐ Unite
L/h
-‐ -‐
N.Ouvert
Pour la régulation du contraste de l'affichage tenir appuyée la touche et dans 5 secondes appuyer sur les
Durante la fase di funzionamento della pompa: premuto visualizza ciclicamente sul display i valori
Per “uscire” dai vari livelli di menu. Prima di uscire definitivamente dalla programmazione si accede alla
richiesta di salvataggio delle modifiche.
Scorre i menu verso l’alto, oppure incrementa i valori numerici da modificare. Nella modalità Batch
può avviare il dosaggio
Connessioni elettriche
1
Relè d’allarme
2
3
Non abilitati
4
9
Ingressi sensore di flusso
10
Ingresso sonda controllo
B
livello
Hayward Flow Control www.haywardflowcontrol.com 1-888-INDL (1-888-429-4635)
ZKDIOM
Pg. 1 of 10
Menu di Programmazione HAYWARD ZKD
Premendo il tasto per più di tre secondi si accede alla programmazione. Con i tasti potrete scorrere
Con il pulsante si esce dai livelli della programmazione. All’uscita dalla programmazione il display visualizza:
Exit Exit
No Save ∇ Δ Save per confermare la scelta
PROG
Configurazione
-‐ +
Paus
Calib. Pompa N.Aperto Paragrafo 12
Paragrafo 6 cc/colpo
Unità
Paragrafo 11
Statistiche
Paragrafo 7 Ore
Allarme
Paragrafo 10
Livello
Paragrafo 8 Allarme
Paragrafo 9
Flusso
Configurazione
Funzioni pompa
-‐ +
Portata Massima Lingua
Paragrafo 4 italiano
Rele allarme
Paragrafo 5 Aperto
Funzioni pompa
Paragrafo 1
Manuale
-‐ +
Pump Functions
Permette di selezionare la lingua, di fabbrica la pompa è
-‐ impostata in inglese.
Max flow rate
-‐
P100%
Premendo si accede alla modifica, quindi con i tasti
Alarm Relay imposto il valore. Con confermo e torno al
-‐
N.Open
menu principale
Language
-‐ +
-‐
English
-‐
Configurazione
Configurazione
Funzioni pompa La pompa lavora in modalità costante e la portata può essere regolata solo
Configurazione
Configurazione
Funzioni pompa
- +
Funzioni pompa
Dos.settimanale
- -
1)
-
2)
Dos.settimanale PROG01 LMMGVSD PROG01 hh.mm
00.00 _______ + + +
-
Orario 00.00
ESC
-
3)
PROG01
+
-
Q.ta 0ml
-
4)
PROG01
+
- -
Tempo dos. 0 s
-
5)
PROG01 PROG01
+
-
Rel.Off Rel.Off
6)
PROG01
Giorni
LMMGVSD
_______ - +
Orologio
Mar 08:00 - + - + - +
È possibile programmare 10 dosaggi per l’intera settimana. Premendo dal “Dos.settimanale” accedo alla
possibilità di programmare i dosaggi.
3) Quantità da dosare, con i tasti posso imposto il valore in “ml” e con lo confermo.
4) Tempo di dosaggio, cioè in quanto tempo (in secondi) voglio dosare la quantità precedentemente programmata,
5) Impostazione relè collegato al dosaggio, con i tasti modifico i valori e con li confermo; in modalità
“Off” il relè non rimane spento (aperto), in modalità “dopo” il relè si chiude al momento dell’attivazione del dosaggio
e rimane chiuso a dosaggio terminato per il tempo (in secondi) che si imposta con i tasti , quindi confermo
premendo . In modalità “prima” il relè si chiude prima del tempo di attivazione del dosaggio, per un tempo (in
quantità, durata del dosaggio e modalità funzionamento relè). Con accedo alle modifiche, quindi con il tasto
attivo/disattivo il dosaggio, con il tasto cambio giorno della settimana. Premendo confermo e passo
automaticamente al programma successivo.
Se ho bisogno di programmare il nuovo programma ripeto la procedura precedente, altrimenti premendo torno
al menu principale.
Nel menu principale il passo successivo è la programmazione dell’orologio, premendo il tasto accedo alle
modifiche, con i tasti imposto i valori, quindi confermo premendo . In sequenza posso impostare il
giorno, l’ora ed i minuti. Ovviamente il giorno e l’orario impostati sono quelli cui farà riferimento la programmazione.
Trigger Quantità
PROG
Configurazione
Ritardo Interv.
Configurazione
Funzioni pompa Impostando, ad esempio, un tempo Interv.= 0 si ottiene un sistema
nel quale la quantità programmata viene dosata dopo ogni segnale di
- +
TRIGGER (con l’eventuale ritardo impostato):
Funzioni pompa
Tempo
Trigger Trigger
Tempo
- +
-
Quantita 100ml
Tempo g.hh.mm
- +
-
Ritardo 0.01.50
Ritardo Ritardo
Tempo g.hh.mm
- +
-
Interval 0.01.50
È possibile avviare il dosaggio anche premendo il tasto +, il quale
Mod. Trigger Mod. Trigger praticamente simula il segnale di Trigger.
-
Off
programmato e la sua attivazione blocca il dosaggio, mentre la
successiva disattivazione rimette il sistema in attesa del segnale
Trigger per un nuovo dosaggio.
Quantità
PROG
Configurazione
-
Riavvia Tempo Riavvia Tempo
- -
Blocca Tempo
per aumentare la frequenza oppure i tasti per
Mod. Ingr. Pausa
diminuirla.
Pausa dosaggio
Configurazione
Permette di impostare la massima portata raggiungibile
dalla pompa e la modalità programmata (% o frequenza)
Configurazione
diventa la visualizzazione della portata nell’unità di misura
-‐
Funzioni pompa
-‐
F320s/m
Configurazione
-‐
P100%
Configurazione
Cal. Automatica
ml 20 -‐ +
Paragrafo 7 – Statistiche
Programmazione Funzionamento
PROG
Configurazione
-‐
Nel menu principale visualizza le ore di funzionamento della
-‐
Statistiche
Ore 10
pompa, premendo il tasto accedo alle altre statistiche:
- Colpi = numero di colpi eseguito dalla pompa
- Q.ta(L) = quantità dosata dalla pompa espressa in litri;
Statistiche
Colpi 1000 questo dato viene calcolato in base al valore cc/colpo in
-‐ memoria
- Accensioni = numero di avviamenti della pompa
Statistiche
-‐
Q.ta(l) 100
-‐
Ore 10
Paragrafo 8 – Password
Programmazione Funzionamento
P RO G
Configurazione
-‐
Permette di attivare (disattivare) il sensore di flusso.
-‐ Una volta attivato (On) premendoli tasto si accede alla
Allarme Allarme flusso
richiesta di quanti segnali aspetta la pompa prima di andare
-‐
Flusso Off Off
+
Allarme flusso in allarme. Premendo lampeggia il numero, quindi con i
On
-‐
Paragrafo 10 – Allarme di livello
Programmazione Funzionamento
PROG
-‐
Livello Stop Stop
Premendo si accede alla modifica, quindi con i tasti
-‐
Allarme livello
Allarme
imposto il tipo di allarme. Con confermo.
ESC
Allarme
Livello Allarme Premendo torno al menu principale
-‐
Paragrafo 11 – Unità visualizzazione portata
Programmazione Funzionamento
PROG
Permette di impostare l’unità di misura del dosaggio a
Configurazione
-‐ -‐
N.Aperto
Per la regolazione del contrasto del display tenere premuto il tasto e entro 5 secondi premere i tasti o
per incrementare o meno il contrasto.
Allarmi
Visualizzazione Causa Interruzione
Led Alarm fisso Allarme fine di livello, senza Ripristino del livello del liquido.
Scritta lev lampeggiante interruzione del funzionamento della
Es: Man pompa
Lev P100%
Led Alarm fisso Allarme fine di livello, con Ripristino del livello del liquido
Scritta lev e stop lampeggiante interruzione del funzionamento della
Es: Man pompa
Lev Stop P100%
Led Alarm fisso Allarme di flusso attivo, la pompa
Scritta Flw lampeggiante non ha ricevuto il numero di segnali Pressione del tasto
Es: Man F programmati dal sensore di flusso.
Flw P100%
Errore di comunicazione interna
Es: Parameter Error della CPU. Pressione del tasto per
PROG to default ripristinare i parametri di fabbrica.