Professional Documents
Culture Documents
Bumpers: 2008 Chrysler Aspen Limited 2008 Chrysler Aspen Limited
Bumpers: 2008 Chrysler Aspen Limited 2008 Chrysler Aspen Limited
Bumpers: 2008 Chrysler Aspen Limited 2008 Chrysler Aspen Limited
2008 ACCESSORIES AND EQUIPMENT Frame & Bumpers - Aspen & Durango
BUMPERS
FASCIA-FRONT
REMOVAL
FASCIA-FRONT
INSTALLATION
FASCIA-FRONT
1. Place the upper edge of fascia (1) onto the center support bracket under the grille and push on to snap
retainers (2) together.
2. Insert the retainer pins (3) on the ends of the fascia into the holes in the lower fender flanges.
Microsoft
Tuesday, April 27, 2010 8:45:47 AM Page 2 © 2006 Mitchell Repair Information Company, LLC.
2008 Chrysler Aspen Limited
2008 ACCESSORIES AND EQUIPMENT Frame & Bumpers - Aspen & Durango
Microsoft
Tuesday, April 27, 2010 8:45:47 AM Page 3 © 2006 Mitchell Repair Information Company, LLC.
2008 Chrysler Aspen Limited
2008 ACCESSORIES AND EQUIPMENT Frame & Bumpers - Aspen & Durango
SUPPORT-FRONT FASCIA
REMOVAL
SUPPORT-FRONT FASCIA
Microsoft
Tuesday, April 27, 2010 8:45:47 AM Page 4 © 2006 Mitchell Repair Information Company, LLC.
2008 Chrysler Aspen Limited
2008 ACCESSORIES AND EQUIPMENT Frame & Bumpers - Aspen & Durango
Microsoft
Tuesday, April 27, 2010 8:45:47 AM Page 5 © 2006 Mitchell Repair Information Company, LLC.
2008 Chrysler Aspen Limited
2008 ACCESSORIES AND EQUIPMENT Frame & Bumpers - Aspen & Durango
INSTALLATION
SUPPORT-FRONT FASCIA
Microsoft
Tuesday, April 27, 2010 8:45:47 AM Page 6 © 2006 Mitchell Repair Information Company, LLC.
2008 Chrysler Aspen Limited
2008 ACCESSORIES AND EQUIPMENT Frame & Bumpers - Aspen & Durango
1. Install the fog lamps into the bumper, if necessary, refer to INSTALLATION .
2. Position the bumper onto the bumper support and seat the tabs fully.
Microsoft
Tuesday, April 27, 2010 8:45:47 AM Page 7 © 2006 Mitchell Repair Information Company, LLC.
2008 Chrysler Aspen Limited
2008 ACCESSORIES AND EQUIPMENT Frame & Bumpers - Aspen & Durango
Microsoft
Tuesday, April 27, 2010 8:45:47 AM Page 8 © 2006 Mitchell Repair Information Company, LLC.
2008 Chrysler Aspen Limited
2008 ACCESSORIES AND EQUIPMENT Frame & Bumpers - Aspen & Durango
BUMPER-FRONT
REMOVAL
BUMPER-FRONT
Microsoft
Tuesday, April 27, 2010 8:45:47 AM Page 9 © 2006 Mitchell Repair Information Company, LLC.
2008 Chrysler Aspen Limited
2008 ACCESSORIES AND EQUIPMENT Frame & Bumpers - Aspen & Durango
INSTALLATION
BUMPER-FRONT
Microsoft
Tuesday, April 27, 2010 8:45:47 AM Page 10 © 2006 Mitchell Repair Information Company, LLC.
2008 Chrysler Aspen Limited
2008 ACCESSORIES AND EQUIPMENT Frame & Bumpers - Aspen & Durango
1. Install the bumper support (1) and install the nuts (2).
2. Tighten the nuts to 109 N.m (80 ft. lbs.).
3. Install the front bumper. See INSTALLATION.
FASCIA-REAR
REMOVAL
FASCIA-REAR
Microsoft
Tuesday, April 27, 2010 8:45:47 AM Page 11 © 2006 Mitchell Repair Information Company, LLC.
2008 Chrysler Aspen Limited
2008 ACCESSORIES AND EQUIPMENT Frame & Bumpers - Aspen & Durango
Microsoft
Tuesday, April 27, 2010 8:45:47 AM Page 12 © 2006 Mitchell Repair Information Company, LLC.
2008 Chrysler Aspen Limited
2008 ACCESSORIES AND EQUIPMENT Frame & Bumpers - Aspen & Durango
4. Open the liftgate and remove the upper push pin fasteners (2).
5. Remove the fascia (3).
INSTALLATION
FASCIA-REAR
Microsoft
Tuesday, April 27, 2010 8:45:47 AM Page 13 © 2006 Mitchell Repair Information Company, LLC.
2008 Chrysler Aspen Limited
2008 ACCESSORIES AND EQUIPMENT Frame & Bumpers - Aspen & Durango
1. Position the fascia (3) and install the push pin fasteners (2).
Microsoft
Tuesday, April 27, 2010 8:45:47 AM Page 14 © 2006 Mitchell Repair Information Company, LLC.
2008 Chrysler Aspen Limited
2008 ACCESSORIES AND EQUIPMENT Frame & Bumpers - Aspen & Durango
SUPPORT-REAR BUMPER
REMOVAL
SUPPORT-REAR BUMPER
Microsoft
Tuesday, April 27, 2010 8:45:47 AM Page 15 © 2006 Mitchell Repair Information Company, LLC.
2008 Chrysler Aspen Limited
2008 ACCESSORIES AND EQUIPMENT Frame & Bumpers - Aspen & Durango
INSTALLATION
SUPPORT-REAR BUMPER
Microsoft
Tuesday, April 27, 2010 8:45:47 AM Page 16 © 2006 Mitchell Repair Information Company, LLC.
2008 Chrysler Aspen Limited
2008 ACCESSORIES AND EQUIPMENT Frame & Bumpers - Aspen & Durango
1. Position the foam support (2) and install new rivets (3).
2. Install the rear fascia. See INSTALLATION.
BRACKET-REAR FASCIA
REMOVAL
BRACKET-REAR FASCIA
Microsoft
Tuesday, April 27, 2010 8:45:47 AM Page 17 © 2006 Mitchell Repair Information Company, LLC.
2008 Chrysler Aspen Limited
2008 ACCESSORIES AND EQUIPMENT Frame & Bumpers - Aspen & Durango
INSTALLATION
BRACKET-REAR FASCIA
Microsoft
Tuesday, April 27, 2010 8:45:47 AM Page 18 © 2006 Mitchell Repair Information Company, LLC.
2008 Chrysler Aspen Limited
2008 ACCESSORIES AND EQUIPMENT Frame & Bumpers - Aspen & Durango
1. Install the brackets (3) and (4) and install the bolts (1), (2) and (5).
2. Install the fascia. See INSTALLATION.
Microsoft
Tuesday, April 27, 2010 8:45:47 AM Page 19 © 2006 Mitchell Repair Information Company, LLC.