Professional Documents
Culture Documents
BS EN 60684-3-121 To 124-2001
BS EN 60684-3-121 To 124-2001
60684-3-121 to
124:2001
IEC
60684-3-121 to
Flexible insulating 124:2001
sleeving —
Part 3: Specifications for individual
types of sleeving —
Sheets 121 to 124: Extruded silicone
sleeving
ICS 29.035.20
National foreword
English version
This European Standard was approved by CENELEC on 2001-09-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic,
Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands,
Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
© 2001 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Foreword
The text of document 15C/1215/FDIS, future edition 2 of IEC 60684-3-121 to 124, prepared by SC 15C,
Specifications, of IEC TC 15, Insulating materials, was submitted to the IEC-CENELEC parallel vote and
was approved by CENELEC as EN 60684-3-121 to 124 on 2001-09-01.
This European Standard supersedes HD 523.3.121 & 122 S1:1990 and EN 60684-3-123 & 124:1995.
Endorsement notice
The text of the International Standard IEC 60684-3-121 to 124:2001 was approved by CENELEC as a
European Standard without any modification.
__________
Page 3
EN 60684−3−121 to 124:2001
INTRODUCTION
This International Standard is one of a series which deals with flexible insulating sleeving for
electrical purposes.
om
. c
x w
zf
. b
w
ww
享网
分
标准
Page 4
EN 60684−3−121 to 124:2001
1 Scope
These sheets of IEC 60684-3 gives the requirements for four types of non-heatshrinkable
sleeving, extruded from silicone elastomer.
These sleevings are normally available with internal diameter up to 25 mm and in a range of
wall thicknesses between 0,1 mm and 2,0 mm. National standards may select a restricted list
of preferred combinations of internal diameter and wall thickness.
These sleevings are normally available in the following opaque colours: black, brown, red,
translucent form.
om
orange, yellow, green, blue, violet, grey, white and pink. They are also available in a
. c
x w
Sizes or colours other than those specifically listed in this standard may be available as custom
items. These items shall be considered to comply with this standard if they comply with the
other property requirements listed in table 2.
zf
. b
2 Normative references
w
ww
The following normative documents contain provisions which, through reference in this text,
constitute provisions of this part of IEC 60684. For dated references, subsequent amendments
享网
to, or revisions of, any of these publications do not apply. However, parties to agreements
based on this part of IEC 60684 are encouraged to investigate the possibility of applying the
分
most recent editions of the normative documents indicated below. For undated references, the
标准
latest edition of the normative document referred to applies. Members of IEC and ISO maintain
registers of currently valid International Standards.
IEC 60684-1:1980, Specification for flexible insulating sleeving – Part 1: Definitions and
general requirements
IEC 60684-2:1997, Specification for flexible insulating sleeving – Part 2: Methods of test
3 Designation
Any abbreviation used for colour shall comply with IEC 60757, where applicable. Non-standard
colours shall be written out in full. The abbreviation for translucent shall be “TL”
om
4 Requirements . c
x w
f
In addition to the general requirements given in IEC 60684-1, the sleeving shall comply with the
z
requirements in tables 1, 2 and 3.
. b
w
ww
5 Product qualification
Product qualification shall normally be based on results from 8 mm internal diameter black
网
sleeving. Colour fastness to light shall be qualified for all colours.
享
分
标准
Page 6
EN 60684−3−121 to 124:2001
+0,10
0,3
–0,05
0,5
+0,15
0,8
–0,10
1,0
+0,20
1,5
–0,15
2,0
2,5
3
±0,20
4
5
6
om
8
10 .
±0,25 c
12
x w
16
zf
20
. b ±0,50
25
w
ww
NOTE 1 Measurements shall be made to the nearest 0,05 mm.
NOTE 2 See table 3 for wall thicknesses.
享网
分
标准
Page 7
EN 60684−3−121 to 124:2001
ww
– after damp heat 23.4.4 1 ´ 10 10
网
(sheets 121 and Method A be burned away. The cotton shall not
122 only) be ignited.
Electrolytic
corrosion
分 享
31 – Max.
Negative pole 1, 4 Visual method
标准
Positive pole A/B
Thermal The end point shall be 50 % of the
37 – Min. 180
endurance initial value of tensile strength
Page 8
EN 60684−3−121 to 124:2001
The breakdown voltage shall be determined by any of the methods given in 21.2, 21.3, 21.4
and 21.5 of IEC 60684-2. The central value shall comply with the minimum value in the table
below.
The rate of application of the voltage shall be either 500 V/s or such that the required value is
reached within 10 s to 20 s.
0,5
+0,15
5,5
om 4,0
0,7
–0,05
8,0 . c 6,0
x w
1,0 10,7
zf 8,0
1,5 ±0,20
.
16,0
b 12,0
2,0
w 20,0 15,0
ww
* This wall thickness is normally only available for sleevings of nominal internal diameter up to and including
1 mm.
享网
分 __________
标准
Page 9
EN 60684−3−121 to 124:2001
Annex ZA
(normative)
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of any
of these publications apply to this European Standard only when incorporated in it by amendment or
revision. For undated references the latest edition of the publication referred to applies (including
amendments).
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
. b
w
ww
享网
分
标准
BS EN
60684-3-121 to
124:2001 BSI — British Standards Institution
BSI is the independent national body responsible for preparing
British Standards. It presents the UK view on standards in Europe and at the
international level. It is incorporated by Royal Charter.
Revisions
British Standards are updated by amendment or revision. Users of
British Standards should make sure that they possess the latest amendments or
editions.
It is the constant aim of BSI to improve the quality of our products and services.
We would be grateful if anyone finding an inaccuracy or ambiguity while using
this British Standard would inform the Secretary of the technical committee
responsible, the identity of which can be found on the inside front cover.
Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.
BSI offers members an individual updating service called PLUS which ensures
that subscribers automatically receive the latest editions of standards.
Buying standards
Orders for all BSI, international and foreign standards publications should be
addressed to Customer Services. Tel: +44 (0)20 8996 9001.
Fax: +44 (0)20 8996 7001. Email: orders@bsi-global.com. Standards are also
available from the BSI website at http://www.bsi-global.com.
om
. c
In response to orders for international standards, it is BSI policy to supply the
BSI implementation of those that have been published as British Standards,
unless otherwise requested.
x w
Information on standards
zf
. b
BSI provides a wide range of information on national, European and
w
international standards through its Library and its Technical Help to Exporters
Service. Various BSI electronic information services are also available which give
ww
details on all its products and services. Contact the Information Centre.
Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: info@bsi-global.com.
享网
Subscribing members of BSI are kept up to date with standards developments
and receive substantial discounts on the purchase price of standards. For details
分
of these and other benefits contact Membership Administration.
标准
Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001.
Email: membership@bsi-global.com.
Information regarding online access to British Standards via British Standards
Online can be found at http://www.bsi-global.com/bsonline.
Further information about BSI is available on the BSI website at
http://www.bsi-global.com.
Copyright
Copyright subsists in all BSI publications. BSI also holds the copyright, in the
UK, of the publications of the international standardization bodies. Except as
permitted under the Copyright, Designs and Patents Act 1988 no extract may be
reproduced, stored in a retrieval system or transmitted in any form or by any
means – electronic, photocopying, recording or otherwise – without prior written
permission from BSI.
This does not preclude the free use, in the course of implementing the standard,
of necessary details such as symbols, and size, type or grade designations. If these
details are to be used for any other purpose than implementation then the prior
BSI written permission of BSI must be obtained.
389 Chiswick High Road Details and advice can be obtained from the Copyright & Licensing Manager.
London Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553.
Email: copyright@bsi-global.com.
W4 4AL