Professional Documents
Culture Documents
Catalogue Aircraft Tools
Catalogue Aircraft Tools
Catalogue Aircraft Tools
A S
AIRCRAFT TOOL
SUPPLY COMPANY
WHAT’S NEW
1-800-248-0638
WHAT’S NEW
www.aircraft-tool.com
WHAT’S NEW
CHERRY® POWER RIVETERS
NOTE: pulling heads are not furnished with Riveters and must be purchased separately.
1-800-248-0638
WHAT’S NEW
IMPERIAL® PRODUCTS
1 - ROL-AIR® 37° FLARING TOOL
The industry standard Rol-Air® is the choice of professionals. Flares soft copper, alumi-
num and brass tubing. The faceted, hard chrome coated cone rolls out perfect 37°
flares above the die block, and then automatically burnishes the flare face while main-
taining the original wall thickness at the base of flare. New slip-on yoke permits use in
tight quarters. Satin chrome and black finish. Not recommended for stainless steel.
No. 507FB..............(3/16”, 1/4”, 5/16”, 3/8”, 1/2”, & 5/8” O.D. tubing) .............$79.95
www.aircraft-tool.com
WHAT’S NEW
L&R ULTRASONIC CLEANERS
L&R Ultrasonic Cleaning Systems feature their exlusive new Sweep-
Zone™ Technology with “Smart Circuit,” a custom engineered electronic
component that offers the latest in efficient and complete ultrasonic
cleaning. This circuit creates Constant Power Output (CPO) for consistent,
uniform cleaning.
SweepZone™ Technology incorporates Pulse Width Modulation (PWM), allow-
ing the cleaner to sense load, solution level and voltage fluctuations – and to automati-
cally adjust to create uniform cleaning power.
SweepZone™ systems feature a cleaning wave of ±2kHz energy that sweeps through
the tank. This offers uniform cleaning power without hot spots or weak areas. All models S140
include a built-in timer, stainless steel lid and drain.
S360
3 - SWEEPZONE MODEL 360 (Deep Well Tank)
Tank Size (LxWxD) Capacity (qt) Overall Size (LxWxH) Weight (lbs)
11-1/2” x 9-1/4” x 8” 14-1/2 12-3/4” x 10-1/2” x 13-1/4” 22
No. S360U........................................... (unheated) ......................................$1,260.00
No. S360H ................................... (with built-in heater) ...............................$1,380.00
No. S360P..............................(stainless steel auxillary pan) ...........................$195.00
1-800-248-0638
WHAT’S NEW
www.aircraft-tool.com
WHAT’S NEW!
RV BUILDER’S KIT
Our new RV Builder’s Kit has been completely revised to closely conform to Van’s recommended tool list for their very popular
line of RV homebuilt airplanes. It contains all of the tools necessary to successfully assemble the RV4, RV6, RV8, and RV9 series
of homebuilt airplanes.
No. RVK-2602.............................................. (with 2602 Economy Rivet Gun) .....................................................$1,385.95
No. RVK-2X ........................................................... (with 2X Rivet Gun) ...............................................................$1,415.95
No. RVK-3X ........................................................... (with 3X Rivet Gun) ...............................................................$1,420.95
No. RVK-4X ........................................................... (with 4X Rivet Gun) ...............................................................$1,425.95
1-800-248-0638
RIVETING KITS
MUSTANG BUILDER’S KIT
This kit contains the majority of the tools needed in every phase of constructing the popular Kit Mustang. It’s designed to provide
only the tools you will need to get the job done quickly and professionally.
No. MUS-2602............................................. (with 2602 Economy Rivet Gun) ........................................................$619.95
No. MUS-2X .......................................................... (with 2X Rivet Gun) ..................................................................$665.95
No. MUS-3X .......................................................... (with 3X Rivet Gun) ..................................................................$669.95
No. MUS-4X .......................................................... (with 4X Rivet Gun) ..................................................................$675.95
www.aircraft-tool.com
RIVETING KITS
MASTER BUILDERS KIT
The Master Builder’s Kit is our most comprehensive riveting kit. It contains the tooling needed to build some of the most popular
aluminum airplanes, including the RV series, the Thorp T-18, the Midget Mustang, and many others. This kit is also very popular
with airframe mechanics needing an all-in-one riveting kit.
No. MBK-2602............................................. (with 2602 Economy Rivet Gun) .....................................................$1,189.50
No. MBK-2X .......................................................... (with 2X Rivet Gun) ...............................................................$1,229.50
No. MBK-3X .......................................................... (with 3X Rivet Gun) ...............................................................$1,235.50
No. MBK-4X .......................................................... (with 4X Rivet Gun) ...............................................................$1,239.50
1-800-248-0638
RIVETING KITS
DELUXE RIVETING KIT
Our Deluxe Riveting Kit contains everything needed to build and maintain all metal aircraft. This kit is highly recommended for
the professional mechanic or the experienced home builder.
No. 135-26KT .............................................. (with 2602 Economy Rivet Gun) ........................................................$750.95
No. 135-2XKT ........................................................ (with 2X Rivet Gun) ..................................................................$789.95
No. 135-3XKT ........................................................ (with 3X Rivet Gun) ..................................................................$795.95
No. 135-4XKT ........................................................ (with 4X Rivet Gun) ..................................................................$799.95
www.aircraft-tool.com
RIVETING KITS
UNIVERSITY STUDENTS RIVETING KIT AIRCRAFT MECHANIC’S RIVETING KIT
This kit is specifically designed for the Airframe student. It’s equipped A perfect starter kit for the A&P mechanic, the KT series of kits contains
with all of the essential tools needed to work on sheet metal. This just the essentials needed for riveting. This kit is most commonly used
kit is currently being used by students in schools such as Vincennes as a starting point for mechanics wishing to make their own custom-
University and others. ized kits.
No. 2602STUD..................................................................... $249.95 No. 2602KT......................................................................... $229.95
No. 2XSTUD.........................(with 2X gun)........................... $285.95 No. 2XKT.............................(with 2X gun)........................... $265.95
No. 3XSTUD.........................(with 3X gun)........................... $289.95 No. 3XKT.............................(with 3X gun)........................... $269.95
No. 4XSTUD.........................(with 4X gun)........................... $295.95 No. 4XKT.............................(with 4X gun)........................... $275.95
Didn’t find the kit you were looking for?... Why not build your own!
Fax us at 1-989-739-1448 with the tool list of your dream kit and we’ll price it for you. Better yet, send us your list via e-mail to
mykit@aircraft-tool.com to receive an immediate quotation. And be sure to include your delivery address and preferred method of ship-
ment if you would like us to also quote shipping charges.
1-800-248-0638
SHEET METAL FASTENERS
1 - CLECO PLIERS
For use with all spring loaded fasteners and clamps.
No. 131 ..............................................................................................................$4.75
www.aircraft-tool.com
RIVETS
CHERRYMAX® FLUSH HEAD CHERRYMAX® UNIVERSAL HEAD
GRIP
SIZE
LENGTH
Nominal (CR3212) Oversize (CR3242) Nominal (CR3213) Oversize (CR3243)
50 pcs 100 pcs 50 pcs 100 pcs 50 pcs 100 pcs 50 pcs 100 pcs
4-1 VARIES N/A N/A 34.95 54.95 33.95 52.95 33.95 52.95
4-2 .063-.125 28.95 45.95 28.95 45.95 28.95 45.95 28.95 45.95
4-3 .126-.187 28.95 45.95 28.95 45.95 28.95 45.95 28.95 45.95
4-4 .188-.250 28.95 45.95 28.95 45.95 28.95 45.95 28.95 45.95
4-5 .251-.312 34.95 48.95 37.95 58.95 30.95 48.95 33.95 52.95
4-6 .313-.375 39.95 62.95 42.95 67.95 39.95 62.95 39.95 62.95
4-7 .376-.437 72.95 115.95 77.95 123.95 57.95 93.95 64.95 104.95
4-8 .438-.500 83.95 132.95 92.95 147.95 81.95 131.95 92.95 149.95
5-1 .031-.062 N/A N/A N/A N/A 37.95 59.95 39.95 62.95
5-2 .063-.125 33.95 52.95 34.95 54.95 31.95 49.95 34.95 54.95
5-3 .126-.187 33.95 52.95 34.95 54.95 31.95 49.95 34.95 54.95
5-4 .188-.250 34.95 54.95 36.95 57.95 33.95 52.95 36.95 57.95
5-5 .251-.312 37.95 58.95 38.95 59.95 36.95 57.95 37.95 58.95
5-6 .313-.375 42.95 67.95 39.95 62.95 39.95 62.95 39.95 62.95
5-7 .376-.437 66.95 105.95 69.95 110.95 63.95 101.95 61.95 97.95
5-8 .438-.500 76.95 122.95 79.95 123.95 73.95 117.95 77.95 123.95
6-1 .037-.062 N/A N/A N/A N/A 49.95 79.95 47.95 75.95
6-2 .063-.125 38.95 61.95 39.95 62.95 39.95 62.95 39.95 62.95
6-3 .126-.187 38.95 61.95 39.95 62.95 39.95 59.95 39.95 62.95
6-4 .188-.250 38.95 61.95 39.95 62.95 39.95 59.95 41.95 65.95
6-5 .251-.312 39.95 62.95 42.95 67.95 39.95 63.95 44.95 71.95
6-6 .313-.375 42.95 72.95 44.95 71.95 42.95 67.95 48.95 75.95
6-7 .376-.437 54.95 84.95 57.95 91.95 54.95 86.95 61.95 97.95
6-8 .438-.500 77.95 123.95 77.95 123.95 77.95 123.95 77.95 123.95
1-800-248-0638
RIVETS
Our rivet removal tool comes complete with four drill bits and guides
SOLID RIVET ASSORTMENT for removing 3/32”, 1/8”, 5/32” and 3/16” universal head (AN470) solid
rivets. Rivets are cleanly removed without damage to the rivet hole or
This is an assortment of solid universal and flush rivets in the most
aircraft skin. Fits any 1/4” air or electric drill. Made in U.S.A.
popular sizes. You’ll get 1/4lb of universal head rivets (MS20470 series)
and 1/4lb of flush head rivets (MS20426 series) rivets in each of the
following sizes: 3-4, 4-4, 5-4, 6-4, 3-5, 4-5, 5-5, 6-5, 3-6, 4-6, 5-6 & Note: Replacement bits for the rivet removal tool are our “L” series
6-6. A total of 6lbs of rivets. threaded drill bits (e.g. 5000-40L).
No. MS20KIT ......................................................................... $75.95 No. 1341 .............................................................................. $49.95
www.aircraft-tool.com
BUCKING BARS
140 141 142 147
5-1/8” long, 3” wide, 1-5/8” high. 10-3/8” long, 1” wide, 2” high. 3 6-3/8” long, 1” wide, 2-1/4” high. 5-1/4” long, 2” wide, 1” high. 1.5
2 lbs cast steel lbs cast steel 2 lbs cast steel lbs cast steel.
No. 140 .......................... $14.95 No. 141 .......................... $12.95 No. 142 .......................... $14.95 No 147........................... $14.95
3-3/4” long, 2” wide, 1” high. 1.5 5-1/2” long, 1-1/2” wide, 2” high. 6” long, 3/4” wide, 1-3/4” high. 1.5 2-1/2” long, 2” wide, 1-1/2” high.
lbs cast steel 3” lbs cast steel lbs machined steel 1 lb machined steel
No 148........................... $14.95 No. 149 .......................... $12.95 No. 150 .......................... $14.95 No. 153 .......................... $14.95
6” long, 1-1/2” wide, 1-1/2” high. 4” long, 1” wide, 2” high. 1.75 lbs 6-3/8” long, 2” small x 2-3/4” large 3-1/2” long, 2” wide, 1” high. 1.5
1.75 lbs machined steel. machined steel dia. 4 lbs machined steel. lbs machined steel.
No. 154 .......................... $12.95 No. 161 .......................... $14.95 No. AT601SP ................... $29.95 No. AT605SP ................... $18.95
8” long, ½” wide, 1” high. 1 lb 12” long, ½” wide, 2” high. 2-1/4 5-1/4” long, ½” wide, 6” high. 2 6” long, 1” wide, 2” high. 1-1/2”
machined steel. lbs machined steel lbs machined steel. machined steel.
No. AT624....................... $26.95 No.. AT646...................... $21.95 No. AT715....................... $29.95 No. AT659....................... $29.95
The 6 piece package has the following bucking bars: 140, 141, 142,
147, 148, and 149
Part No. 6PC ............................................................................ $79.95
5-1/2” long, 1-1/2” wide, 2-3/8” 8” long, 3” wide, 1-1/2” high. 1- The 10 piece package consists of each of the following: 140, 141, 142,
high. 3 lbs machined steel. 1/2 lbs machined steel. 147, 148, 149, 150, 153, 154 and 161.
No. AT750P..................... $19.95 No. AT750-23 ................. $15.95 Part No. 10PC ........................................................................ $135.95
1-800-248-0638
RIVET GUNS
www.aircraft-tool.com
RIVET GUNS
3 - RETAINER SPRINGS
Fits most guns.
a. No. 13M ........................................... (set of 2) ...............................................$2.95
b. No. 513M .....................................Safety retainer ........................................$12.95
13M 513M
1-800-248-0638
RIVETING EQUIPMENT
STANDARD RIVET SETS
Part No.
Length Diameters Available Price
Series 470 Series
Universal Straight Series
470-2 2-1/2” 3/32, 1/8, 5/32, 3/16, 1/4 5.50
470-3 3-1/2” 3/32, 1/8, 5/32, 3/16, 1/4 4.95
470-3 3-1/2” 7/32 7.50
470-5 5-1/2” 3/32, 1/8, 5/32, 3/16, 1/4 6.50
470-7 7-1/2” 3/32, 1/8, 5/32, 3/16 7.50 0470 Series
470-10 10-1/2” 3/32, 1/8, 5/32, 3/16 10.95
10 Degree Offset Series
0470-3 3-1/2” 3/32, 1/8, 5/32, 3/16, 1/4 6.95
0470-5 5-1/2” 3/32, 1/8, 5/32, 3/16, 1/4 7.95
0470-7 7-1/2” 3/32, 1/8, 5/32, 3/16 8.95
0470-10 10-1/2” 3/32, 1/8, 5/32, 3/16 12.95
1470 Series
Double Offset Series
1470-5 5-1/2” 3/32, 1/8, 5/32, 3/16 14.95
1470-7 7-1/2” 3/32, 1/8, 5/32, 3/16 16.95
1470-10 10-1/2” 3/32, 1/8, 5/32, 3/16 18.95
Flush Rivet Sets
90 3-1/2” 1” Dia. 11.95 90 Series
94 3-1/2” 1-1/4” Dia. 14.95
95 5-1/2” 1-1/4” Dia. 19.95
094 3-1/2” 1-1/4” Dia. 10 degree offset 18.95
095 5-1/2” 1-1/4” Dia. 10 degree offset 25.95
The 5 piece mix contains the following sizes: The offset mix contains the following sizes: The extra long mix contains the following 4
3/32”, 1/8”, 5/32”, 3/16” and 1 flush set. Each 3/32”, 1/8”, 5/32”, and 3/16”. Each rivet set sizes: 3/32”, 1/8”, 5/32”, and 3/16”. Each rivet
rivet set is 3-1/2” long. is 3-1/2” long. set is 5-1/2” long.
Number 120 ................................... $25.95 Number 121 ................................... $24.95 Number 125 ................................... $25.95
www.aircraft-tool.com
RIVETING EQUIPMENT
1-800-248-0638
RIVETING EQUIPMENT
www.aircraft-tool.com
RIVETING EQUIPMENT
1 - SPRING BACK DIMPLE DIES
The unique shape of a spring back dimple die’s face pushes the metal up slightly be-
fore the dimple is made, resulting in a cleaner, more precise 100° dimple. All dies are
½” in diameter and 1/4” long with a .187” shank.
1-800-248-0638
RIVET SQUEEZERS
FORCE WEIGHT
PART NO. CAPACITY REACH PRICE
(LBS) (LBS)
A214-30-A15 3000 1/8” 1-1/2” 3 $695.00 A214-30 Series
A214-30-A22 2400 1/8” 2-1/4” 4 $875.00
A214-30-A30 1800 3/32” 3” 5 $895.00
A214-60-A15 6000 3/16” 1-1/2” 4 $925.00
A214-60-A22 4600 5/32” 2-1/4” 6 $950.00
A214-60-A30 3400 1/8” 3” 6 $975.00
A214-90-A15 9000 1/4” 1-1/2” 7 $1050.00 A214-60 Series
A214-90-A22 7000 3/16” 2-1/4” 7.5 $1100.00
A214-90-A30 5200 3/16” 3” 8 $1150.00
A = 2.500”, B = 1.375” A = 2.750”, B = 1.250” A = 3.000”, B = 1.375” A = 3.875”, B = 1.250” A = 5.625”, B = 1.250”
No. 14-5............. $125.00 No. 14-6............. $160.00 No. 14-7............. $195.00 No. 14-8............. $195.00 No. 14-9............. $250.00
www.aircraft-tool.com
RIVET SQUEEZERS
1-800-248-0638
POWER RIVETERS
GBP POWER RIVETERS ARE COMPATIBLE WITH CHERRY TEXTRON BRAND RIVETERS. THEY WILL ACCEPT
ALL CORRESPONDING CHERRYMAX® AND CHERRYLOCK® NOSEPIECES AND ADAPTERS.
Cherrymax and Cherrylock are registered trademarks of Cherry Textron, Inc.
NOTE: pulling heads are not furnished with Riveters and must be purchased separately.
www.aircraft-tool.com
POWER RIVETERS
FITS RIVETER
PART NUMBER FIG PRICE
GBP MODEL CHERRY MODEL Figure a
H701B-456 a GBP704 G701A, G704B $199.95
H680B200A b GBP700, GBP784 G700, G784 $199.95
456MAX744-20 b GBP744 G744 $165.95
08MAX744-20 b GBP744 G744 $159.95
Figure b
1-800-248-0638
BLIND RIVETERS
www.aircraft-tool.com
BLIND RIVETERS
1-800-248-0638
BLIND RIVETERS
5 - RIVENUTS
Aluminum “notchless” threaded nut. Grip length of .010 to .075 inches. Sold in pack-
ages of 10 pieces.
No. RIVNUT-6 ...........................................(6-32) ................................................ $2.25
No. RIVNUT-8 ...........................................(8-32) ................................................ $2.50
No. RIVNUT-10 ........................................(10-32) ............................................... $2.75
www.aircraft-tool.com
CUTTERS
2 - MICROSTOP COUNTERSINK
Fits any air or electric drill with a 1/4” chuck. The 1/4-28 female threaded end will accept
any cutter having a male 1/4-28 thread and a diameter of up to 1/2”.
No. 133 ............................................................................................................$21.95
No. 13389 ................................... (No-Mar plastic foot) .....................................$2.95
1-800-248-0638
CUTTERS
www.aircraft-tool.com
CUTTERS
1 - AIRCRAFT COUNTERBORES
Made of High Speed Steel. Requires pilot (see chart below)
AT402 Series (100°) AT403 Series (Flat)
PART PILOT
DIA. LENGTH PRICE
NUMBER SHANK 3 - BAYONET SPOTFACE & COUNTERSINK CUTTERS
4000-1 1/4” 2-3/8” 3/32” $14.95 Made of High Speed Steel Requires pilot (see chart below)
4000-2 9/32” 2-3/8” 3/32” $15.95
PART NUMBER CUTTER PILOT
4000-3 5/16” 2-3/8” 3/32” $15.95 PRICE
4000-4 11/32” 2-3/8” 3/32” $16.95 100° FLAT DIA. SIZE
4000-5 3/8” 2-3/8” 3/32” $15.95 AT402-1 AT403-1 1/4” 3/32” $16.95
4000-6 13/32” 2-3/4” 1/8” $15.95
AT402-1B AT403-1B 1/4” 1/8” $16.95
4000-7 7/16” 2-3/4” 1/8” $15.95
4000-8 15/32” 2-3/4” 1/8” $17.95 AT402-2 AT403-2 5/16” 1/8” $16.95
4000-9 1/2” 2-3/4” 1/8” $16.95 AT402-2B AT403-2B 5/16” 5/32” $16.95
4000-10 17/32” 2-3/4” 1/8” $18.95 AT402-3 AT403-3 3/8” 1/8” $16.95
4000-11 9/16” 2-3/4” 1/8” $18.95 AT402-3B AT403-3B 3/8” 5/32” $16.95
4000-12 19/32” 2-3/4” 1/8” $25.95 AT402-3C AT403-3C 3/8” 3/16” $16.95
4000-13 5/8” 2-3/4” 1/8” $19.95
AT402-4 AT403-4 7/16” 5/32” $17.95
4000-14 21/32” 2-3/4” 3/16” $29.95
4000-15 11/16” 2-3/4” 3/16” $35.95 AT402-4B AT403-4B 7/16” 3/16” $17.95
AT402-5 AT403-5 1/2” 3/16” $18.95
AT402-5B AT403-5B 1/2” 1/4” $18.95
2 - COUNTERBORE PILOTS
AT402-6 AT403-6 9/16” 3/16” $18.95
For use with 4000 series
AT402-6B AT403-6B 9/16” 1/4” $19.95
counterbores (above) AT402-7 AT403-7 5/8” 1/4” $19.95
PART NO. PILOT SHANK PRICE AT402-7B AT403-7B 5/8” 5/16” $21.95
AT402-8 AT403-8 3/4” 1/4” $23.95
1400P-1A 3/32” 3/32” $3.95
1400P-2A #40 3/32” $3.95 AT402-8B AT403-8B 3/4” 5/16” $23.95
1400P-3A 1/8” 3/32” $3.95 AT402-9 A1403-9 7/8” 3/8” $26.95
1400P-3B 1/8” 1/8” $3.95 AT402-10 AT403-10 1” 3/8” $26.95
1400P-4A #30 3/32” $3.95
1400P-4B #30 1/8” $3.95
1400P-5A 5/32” 3/32” $3.95
1400P-5B 5/32” 1/8” $3.95
1400P-6A #21 3/32” $3.95
1400P-6B #21 1/8” $3.95 4 - BACK CUTTER PILOTS
1400P-7A 3/16” 3/32” $3.95
For use with AT402 and AT403 series cutters (above)
1400P-7B 3/16” 1/8” $3.95
1400P-8A #10 3/32” $3.95 PART NO. SIZE PRICE PART NO. SIZE PRICE
1400P-8B #10 1/8” $3.95
AT404-3/32 3/32” $7.95 AT404-1/4 1/4” $7.95
1400P-9A 7/32” 3/32” $3.95
1400P-9B 7/32” 1/8” $3.95 AT404-1/8 1/8” $7.95 AT404-5/16 5/16” $7.95
1400P-10A 1/4” 3/32” $3.95 AT404-5/32 5/32” $7.95 AT404-3/8 3/8 $7.95
1400P-10B 1/4” 1/8” $3.95 AT404-3/16 3/16” $7.95
1400P-11B 9/32” 1/8” $3.95
1400P-11C 9/32” 3/16” $3.95
1400P-12B 5/16” 1/8” $3.95 5 - 100° COUNTERSINKS
1400P-12C 5/16’ 3/16” $3.95 Three flute design
1400P-13B 3/8” 1/8” $3.95 Made of High Speed Steel
1400P-13C 3/8” 3/16” $3.95
1400P-14B 13/32” 1/8” $3.95 PART NO. DIA. SHANK PRICE
1400P-14C 13/32” 3/16” $3.95 2000-1/4x3/16 .250 3/16” $10.95
1400P-15B 7/16” 1/8” $3.95
2000-3/8x1/4 .375 1/4” $7.95
1400P-15C 7/16” 3/16” $3.95
1400P-16B 15/32” 1/8” $3.95 2000-1/2x3/8 .500 3/8” $9.95
1400P-16C 15/32” 3/16” $3.95 2000-5/8x3/8 .625 3/8” $12.95
1400P-17C 1/2” 3/16” $3.95 2000-3/4x3/8 .725 3/8” $19.95
USA & Canada call Toll Free...
31 FINANCIA
L SERV
ICES
CARD
1-800-248-0638
DRILLING EQUIPMENT
PART CHUCK
RPM HP LENGTH WEIGHT PRICE
NUMBER SIZE
1450ES 1/4” 2600 .90 7” 2.5 169.95
1452ES 1/4” 3300 .90 7” 2.5 179.95
1454ES 3/8” 2600 .90 7” 2.6 169.95
1456ES 1/4” 6000 .90 7” 2.5 205.95
PART CHUCK
RPM HP STYLE PRICE
NUMBER SIZE
1410 1/4” 2600 .33 non-reversible 220.95
1412 1/4” 3600 .33 non-reversible 230.95
1410R 1/4” 2000 .20 reversible 250.95
1412R 1/4” 2600 .20 reversible 260.95
www.aircraft-tool.com
DRILLING EQUIPMENT
1-800-248-0638
DRILLING EQUIPMENT
www.aircraft-tool.com
DRILLING EQUIPMENT
1-800-248-0638
DRILLING EQUIPMENT
6 - DUPLICATING/TRANSFER PUNCH
Used to mark holes in overlapping sheets. Overall length of 3-1/2”.
7 - DRILL EXTENSION
Used to extend drill bits, pilot cutters, etc. Has 1/4” shank on one end, and a 1/4” x 28
internal thread at the other. Comes in three different lengths 4”, 7” or 10”.
No. 384 .................................................. 4” OAL ................................................$3.95
No. 387 .................................................. 7” OAL ................................................$4.50
No. 3810 ............................................... 10” OAL ...............................................$4.95
www.aircraft-tool.com
DRILLING EQUIPMENT
1 - STRAP DUPLICATORS
6” CAPACITY 12” CAPACITY
P/N TYPE SIZE PRICE P/N TYPE SIZE PRICE
51 punch #40 $12.95 51-12 punch #40 $16.95
52 punch #30 $12.95 52-12 punch #30 $16.95
53 punch #21 $12.95 53-12 punch #21 $16.95
55 punch #12 $12.95 55-12 punch #12 $16.95
61 drill #40 $8.95 61-12 drill #40 $12.95
62 drill #30 $8.95 62-12 drill #30 $12.95
63 drill #21 $8.95 63-12 drill #21 $12.95
65 drill #12 $8.95 65-12 drill #12 $12.95
71 inverted #40 $8.95 71-12 inverted #40 $12.95
72 inverted #30 $8.95 72-12 inverted #30 $12.95
73 inverted #21 $8.95 73-12 inverted #21 $12.95
75 inverted #12 $8.95 75-12 inverted #12 $12.95
5 - DRILL STOPS
Used to stop the drill bit after reaching a preset depth. Overall length of 1-5/15”
1-800-248-0638
DRILLING EQUIPMENT
All steel construction for long dependable life. Ideal for removing
chips from between metal after drilling rivet holes. 7 - PRECISION TUBE DRILL GUIDE
No. SP2005............................................................................. $3.95
www.aircraft-tool.com
DRILLING EQUIPMENT
PLATE NUT DRILL JIGS
1 - TWO LUG - DOUBLE WING
SCREW A B C D
PART NO. PRICE
SIZE spacing spacing pilot dia. drill size
STANDARD (DWS) DWS
518A #6 .344 .688 .139 #40 $32.95
518B #8 .344 .688 .164 #40 $32.95
518C #10 .344 .688 .191 #40 $32.95
518D 1/4 .500 1.000 .248 #40 $32.95
MINIATURE (DWM)
518NB #6 .203 .406 .112 #40 $35.95
518NC #8 .218 .436 .139 #40 $35.95 DWM
518ND #10 .234 .468 .164 #40 $35.95
518NE 1/4 .250 .500 .191 #40 $35.95
3 - CORNER WING
SCREW A C D
PART NO. PRICE CWS
SIZE spacing pilot dia. drill size
STANDARD (CWS)
518R #6 .344 .139 #40 $36.95
518S #8 .344 .164 #40 $36.95
518T #10 .344 .191 #40 $36.95
518U 1/4 .500 .248 #40 $36.95
MINIATURE (CWM)
CWM
518SB #6 .203 .112 #40 $38.95
518SC #8 .218 .139 #40 $38.95
518SD #10 .234 .164 #40 $38.95
518SE 1/4 .250 .191 #40 $38.95
1-800-248-0638
DRILLING EQUIPMENT
DRILL BITS WIRE SIZES
Dec. 010 012 013 014 101
Size
Equiv. series series series series series
1 0.2280 2.76 4.14 4.14 9.43 1.90
2 0.2210 2.70 3.80 4.14 9.43 1.90
3 0.2130 2.30 3.80 3.80 8.74 1.90
4 0.2090 2.30 3.80 3.80 8.74 1.90
010 series - High-speed steel, jobbers length, 135° split-point. 5 0.2055 2.30 3.80 3.80 8.74 1.90
012 series - Cobalt, jobbers length, 135° split-point. 6 0.2040 2.30 3.80 3.80 8.74 1.90
013 series - High-speed steel, 6” length, 135° split-point. 7 0.2010 2.13 3.80 3.80 8.74 1.67
014 series - High-speed steel, 12” length, 135° split-point. 8 0.1990 2.13 3.80 3.80 7.94 1.67
9 0.1960 2.13 3.80 3.80 7.94 1.67
101 series - High-speed steel, screw machine length, 135° s/p
10 0.1935 2.13 2.88 2.88 7.94 1.67
FRACTIONAL SIZES 11
12
0.1910
0.1890
1.73
1.73
2.70
2.70
3.05
3.05
7.94
7.94
1.67
1.67
Dec. 010 012 013 014 101 13 0.1850 1.90 3.05 3.05 7.76 1.67
Size
Equiv. series series series series series 14 0.1820 1.90 3.05 3.05 7.76 1.67
1/16 0.0625 1.33 2.65 2.65 6.84 - 15 0.1800 1.90 3.05 3.05 7.76 1.67
5/64 0.0781 1.33 2.65 2.65 6.73 - 16 0.1770 1.90 3.05 3.05 7.76 1.67
3/32 0.0938 1.33 2.07 2.07 7.30 1.21 17 0.1730 1.90 3.05 3.05 7.76 1.67
7/64 0.1094 1.38 2.42 2.42 7.30 1.21 18 0.1695 1.61 3.68 3.05 7.76 1.44
1/8 0.1250 1.38 2.42 2.42 7.30 1.21 19 0.1660 1.61 3.05 3.05 7.76 1.44
9/64 0.1406 1.50 2.88 2.88 7.19 1.21 20 0.1610 1.61 3.05 3.05 7.76 1.44
5/32 0.1562 1.50 2.88 2.88 7.19 1.44 21 0.1590 1.61 3.05 3.05 7.76 1.44
11/64 0.1719 1.61 3.05 3.05 7.19 1.44 22 0.1570 1.61 3.05 3.05 7.76 1.44
3/16 0.1875 1.84 3.05 3.05 7.48 1.67 23 0.1540 1.50 2.88 2.88 7.76 1.44
13/64 0.2031 1.90 3.68 3.68 7.94 1.73 24 0.1520 1.50 2.88 2.88 7.76 1.44
7/32 0.2188 2.24 3.68 3.68 7.94 1.96 25 0.1495 1.50 2.88 2.88 7.76 1.44
15/64 0.2344 2.42 3.97 3.97 8.45 1.96 26 0.1470 1.50 2.88 2.88 7.76 1.44
1/4 0.2500 2.47 3.97 3.97 8.45 2.13 27 0.1440 1.50 2.88 2.88 7.76 1.44
17/64 0.2656 3.16 6.27 6.27 10.29 2.53 28 0.1405 1.32 2.88 2.88 7.30 1.21
9/32 0.2812 3.16 6.27 6.27 10.70 2.65 29 0.1360 1.32 2.88 2.88 7.30 1.21
19/64 0.2969 3.80 7.42 7.42 12.88 3.11 30 0.1285 1.32 2.88 2.88 7.30 1.21
5/16 0.3125 3.97 7.42 7.42 13.11 3.11 31 0.1200 1.32 2.42 2.42 7.30 1.21
21/64 0.3281 4.26 8.34 8.34 15.01 3.62 32 0.1160 1.32 2.42 2.42 7.30 1.21
11/32 0.3438 4.77 8.74 8.74 15.01 4.14 33 0.1130 1.32 2.42 2.42 7.30 1.21
23/64 0.3594 5.52 9.89 9.89 15.24 4.95 34 0.1110 1.32 2.42 2.42 7.30 1.21
3/8 0.3750 5.69 10.81 10.81 16.10 4.95 35 0.1100 1.32 2.42 2.42 7.30 1.21
25/64 0.3906 6.50 13.34 13.34 17.14 5.52 36 0.1065 1.32 2.42 2.42 7.30 1.21
13/32 0.4062 6.84 13.34 13.34 18.29 5.52 37 0.1040 1.32 2.42 2.42 7.30 1.21
27/64 0.4219 7.25 14.78 14.78 19.44 6.10 38 0.1015 1.32 2.42 2.42 7.30 1.21
7/16 0.4375 7.48 14.78 14.78 20.59 6.21 39 0.0995 1.32 2.42 2.42 7.30 1.21
29/64 0.4531 8.51 16.22 16.22 21.45 7.30 40 0.0980 1.32 2.42 2.42 7.30 1.21
15/32 0.4688 8.74 16.22 16.22 22.54 7.76 41 0.0960 1.32 2.42 2.42 7.30 1.21
31/64 0.4844 9.32 16.22 16.50 23.00 8.28 42 0.0935 1.32 2.65 2.65 7.30 1.21
½ 0.5000 9.09 16.50 16.50 24.15 8.28 43 0.0890 1.32 2.65 2.65 7.30 1.21
33/64 0.5156 15.07 - - - 17.94 44 0.0860 1.32 2.65 2.65 7.30 1.21
17/32 0.5313 15.87 - - - 18.63 45 0.0820 1.32 2.65 2.65 7.30 1.21
35/64 0.5469 16.96 - - - 19.55 46 0.0810 1.32 2.65 2.65 7.30 1.21
9/16 0.5625 18.00 - - - 19.55 47 0.0785 1.32 2.65 2.65 7.30 1.21
37/64 0.5781 18.23 - - - 22.20 48 0.0760 1.32 2.65 2.65 7.02 -
19/32 0.5938 18.23 - - - 22.20 49 0.0730 1.32 2.65 2.65 7.02 -
39/64 0.6094 19.67 - - - 22.20 50 0.0700 1.32 2.65 2.65 7.02 -
5/8 0.6250 19.67 - - - 22.20 51 0.0670 1.32 2.65 2.65 7.02 -
41/64 0.6406 20.82 - - - 25.13 52 0.0635 1.32 2.65 2.65 7.02 -
21/32 0.6562 20.82 - - - 25.13 53 0.0595 1.32 5.06 5.06 9.25 -
43/64 0.6719 23.81 - - - 26.51 54 0.0550 1.32 5.06 5.06 9.25 -
11/16 0.6875 23.81 - - - 26.51 55 0.0520 1.32 5.06 5.06 9.25 -
Ordering Instructions: Please specify both the series number and the size of the desired drill bit. For example, if you wanted a 3/8” cobalt drill, then you would
indicate part number: 012-3/8.
www.aircraft-tool.com
DRILLING EQUIPMENT
LETTER SIZES THREADED DRILL BITS
DRILL SETS
Made of high-speed steel 118° split point jobbers length. Slow spiral
design makes it ideal for drilling Plexiglas.
• Made from high-speed steel
• Name-brand manufacturer Part No. Diameter Dec. Flute Price
• Jobbers length AC55-1/8 1/8” 0.1250 1-5/8” $3.35
• Made in U.S.A. AC55-5/32 5/32” 0.1562 2” $4.05
AC55-3/16 3/16” 0.1875 2-5/16” $4.05
Part No. Pieces Type Range Price AC55-1/4 1/4” 0.2500 2-3/4” $4.50
P108 13 Fractional 1/16”-1/4” $11.95 AC55-3/8 3/8” 0.3750 3-5/8” $8.35
P129 29 Fractional 1/16”-½” $39.95 AC55-7/16 7/16” 0.4375 4-1/16” $11.45
P60 60 Wire Size 1-60 $39.95 AC55-1/2 1/2” 0.5000 4-1/2” $13.75
P24 24 Letter Size A-Z $39.95
L13 13 Left Fraction 1/64”-1/4” $39.95
UNIBIT DRILL BITS
1-800-248-0638
DRILLING EQUIPMENT
REAMERS HAND EXPANSION REAMERS
High speed steel • straight shank • straight flute Part Dia No. of Flute Overall
Price
Number (in.) Flutes Len. Len (in.)
Decimal Flute Overall
Size Price 016AR 1/4 6 1-7/16 3-7/8 $43.95
Equiv. Length Length
020AR 5/16 6 1-3/4 4 $47.00
15/64 0.2344 1-1/2 6” $14.05
024AR 3/8 6 1-3/4 4-1/4 $49.55
1 0.2280 1-1/2 6” $13.00
2 0.2210 1-1/2 6” $13.00 028AR 7/16 6 1-3/4 4-1/2 $51.45
7/32 0.2188 1-1/4 5” $12.75 032AR ½ 6 1-13/16 5 $53.40
3 0.2130 1-1/4 5” $13.00 036AR 9/16 8 2-1/8 5-1/2 $58.65
4 0.2090 1-1/4 5” $13.00 040AR 5/8 8 2-1/2 6 $64.45
5 0.2055 1-1/4 5” $13.00
6 0.2040 1-1/4 5” $13.00
13/64 0.2031 1-1/4 5” $12.75 BROWN & SHARP TAPERED REAMERS
7 0.2010 1-1/4 5” $13.00
8 0.1990 1-1/4 5” $13.00
9 0.1960 1-1/4 5” $13.00
10 0.1935 1-1/4 5” $13.00
11 0.1910 1-1/4 5” $12.65
12 0.1890 1-1/8 5” $12.05 Straight Shank - Straight Flute
3/16 0.1875 1-1/8 4-1/2” $12.05
Diameter of Reamer Length
13 0.1850 1-1/8 4-1/2” $12.05 No. O.A.L. Price
14 0.1820 1-1/8 4-1/2” $12.05 Large End Small End Of Flute
15 0.1800 1-1/8 4-1/2” $12.05 1 BS .3176 .1974 2-7/8” 4-3/4” $37.80
16 0.1770 1-1/8 4-1/2” $12.05 2 BS .3781 .2474 3-1/8” 5-1/8” $42.50
17 0.1730 1-1/8 4-1/2” $12.05
3 BS .4510 .3099 3-3/8” 5-1/2” $44.90
11/64 0.1719 1-1/8 4-1/2” $12.05
18 0.1695 1-1/8 4-1/2” $12.05 4 BS .5017 .3474 3-11/16” 5-7/8” $47.10
19 0.1660 1-1/8 4-1/2” $12.05 5 BS .6145 .4474 4” 6-3/8” $53.20
20 0.1610 1-1/8 4-1/2” $12.05 6 BS .6808 .4974 4-3/8” 6-7/8” $56.00
21 0.1590 1-1/8 4-1/2” $12.05
22 0.1570 1 4” $12.05
5/32 0.1562 1 4” $12.05 PILOTED REAMERS
23 0.1540 1 4” $12.05
24 0.1520 1 4” $12.05
25 0.1495 1 4” $12.05
26 0.1470 1 4” $12.05
27 0.1440 1 4” $12.05
9/64 0.1406 1 4” $12.05 High Speed Piloted Reamers for all uses; Valve Guides, Valve Guide
28 0.1405 1 4” $12.05 Boss, Rocker Arm & Shaft Bushings; and Rocker Shaft Support Base.
29 0.1360 1 4” $12.05 You specify size. Available from .375 thru .751”.
30 0.1285 7/8 3-1/2” $12.05 PR0l ...................................................................................... $99.95
1/8 0.1250 7/8 3-1/2” $12.05 NOTE: Please specify reamer size & pilot size when ordering.
31 0.1200 7/8 3-1/2” $12.05
32 0.1160 7/8 3-1/2” $12.05
33 0.1130 7/8 3-1/2” $12.05 TAPERED REAMER
34 0.1110 7/8 3-1/2” $12.05
35 0.1100 7/8 3-1/2” $12.05
T-handle style allows you to use it
7/64 0.1094 7/8 3-1/2” $12.05
without any special tools. Ideal
36 0.1065 7/8 3-1/2” $12.05
for expanding holes in sheet
37 0.1040 7/8 3-1/2” $12.05
metal.
38 0.1015 7/8 3-1/2” $12.05
No. G130
39 0.0995 7/8 3-1/2” $12.05
9
40 0.0980 7/8 3-1/2” $12.05
$ 95
Note: Please use a part number of RMR-size when ordering. Example: to order each
a 1/8” reamer, use part number RMR-1/8.
www.aircraft-tool.com
3M PRODUCTS
1 - 3M RIVETERS TAPE
Riveters tape will save you a lot of time when doing those large riveting jobs by securely
holding each rivet in place until you are ready to buck it. Rivets are fully visible through
the transparent adhesive-free center window and, more importantly, your rivets will not
come in contact with the adhesive. The special “green” adhesive on either side of the
clear center leaves no residue upon separation. This is a must for all mechanics and
home-builders.
No. 685-1 ................................... (3/4” wide x 36 yards).....................................$5.50
No. 685-2 .....................................(1” wide x 36 yards) ......................................$7.50
1-800-248-0638
3M PRODUCTS
No EXL1............................................................................................................$25.95
2 - 3M COMBI WHEELS
Alternate flaps of coated abrasive and finishing web makes these wheels perfect for
blending and finishing work. Requires #1 Roloc holder.
6 - 3M ROLOC™ HOLDERS
These holders are made of a durable plastic for less critical grinding and surface con-
ditioning applications. They are compatible with all Roloc discs and wheels.
www.aircraft-tool.com
3M PRODUCTS
1-800-248-0638
FABRIC TOOLS
1- PINKING SHEARS
The blades are drop forged from stainless steel to resist rust and stay sharp for a long
time. Precision matched teeth are designed to easily cut light to heavier materials. Its
zigzag cutting pattern prevents unraveling of the fabric threads. And the ergonomically
designed handles are comfortable even when used for long periods of time. It has an
8” overall length, and a 3” cutting length. This is a professional quality tool made to high
standards.
No. 5350 ................................................ 8”OAL ...............................................$34.95
3 - KEVLAR® KUTTER
New technology from Heritage changes the molecular structure of the steel com-
pound penetrating and hardening its surface to an incredible Rockwell 70! That hard-
ness produces a cutting edge that lasts four times longer than previous cutters. It easily
cuts through Kevlar® and will outlast any other cutter currently on the market. Hot drop
forged from a special steel alloy, and precision ground, these shears will stay sharp and
resist rust and chemicals better than other shears. They feature the Heritage ergonomic
handles that provide a comfortable, natural grip. The overall length is 10” with a cutting
length of 4-3/4”.
No. 8210 ............................................... 10”OAL ..............................................$32.95
5- LEATHER HOLSTER
Manufactured from high quality top grain steer hide, they are extremely durable. Each
holster is correctly stitched and riveted to prevent the points of shears from penetrating.
It has a snapping belt loop so that you can attach and remove it quickly and easily. It’s
the perfect accessory to our Heritage shears.
No. H13 ..............................................................................................................$8.95
www.aircraft-tool.com
COMPOSITE TOOLS
4 - CARBIDE SCRAPER
Carbide double edge scraper for deburring both edges of a sheet at the same time.
The super-hard carbide insets will stay sharp when working with any type of metal or
composite material. The Inserts have 50° edges and may be rotated for extended life.
No. SP225.........................................................................................................$21.50
No. H10 ............................... Replacement Blades (set of 2) ..............................$8.95
5 - VIXEN FILE
The unique curved rake and deep ridges of the vixen file makes it ideal for working on
fiberglass and composites. Unlike ordinary files, the vixen will not load up or become
gummed when working with these materials. The edges are hardened and honed
sharp to withstand the abrasive and dulling effects of composites.
No. FR85-T010 ..................................................................................................$25.95
1-800-248-0638
SHEET METAL TOOLS
2 - SHRINKING HAMMER
For all-around work and fast finishing; does not stretch the metal, 1-1/4” round serrated
head, 1-1/8” square flat head; 4” long; Wt. 14 oz.
No. 55302 ........................................................................................................$29.95
4 - DINGING HAMMER
Perfectly balanced, for light dinging. 6-1/4” long. 1-1/4” round head; 1-3/16” square
head; flat surfaces. Wt. 12 oz.
No. 55358 ........................................................................................................$32.95
6 - SHOT BAG
Heavy-duty leather bag filled with 2-1/2 lbs. of shot. Used to stretch and form metal
without nicks or gouges. 4” wide by 6” long.
No. 55115 ........................................................................................................$32.95
www.aircraft-tool.com
SHEET METAL TOOLS
1-800-248-0638
SHEET METAL TOOLS
1 - ROPER WHITNEY HAND PUNCH
Punches up to 1/4” hole through 16 ga. metal. Sold either as an individual tool or as
a complete kit in a case with 7 punches and dies for 3/32” to 9/32” holes. NOTE: new
style inverted handle allows operation close to work without injury to your hand. Made
in U.S.A.
No. 45 ..............................................(Complete Kit) ........................................$65.95
No. 45PD-3/32...................(3/32” replacement punch & Die) ...........................$9.95
No. 45PD-1/8......................(1/8” replacement punch & Die) ............................$9.95
No. 45PD-3/16...................(3/16” replacement punch & Die) ...........................$9.95
3 - CIRCLE CUTTER
This tool, also known as a “Fly Cutter”, uses a flying cutting bit to cleanly cut holes in
metal, wood, plastic, and hardwoods from 1” to 5-1/2” diameter. The included 1/4”
drill bit automatically forms its own pilot hole prior to cutting . The drill shank is 5/16”. W
strongly recommend a drill-press and safety gear when using this tool.
No. 5B ..............................................................................................................$12.95
No. 555 ................................. (Replacement Cutter Blade) ...............................$2.95
www.aircraft-tool.com
SHEET METAL TOOLS
Their fine serrated jaws and deep offset handles make the Prosnip®
the finest pair of offset snips available. Super hardened jaws cut ef- The SuperSnip cuts cleanly and accurately without damage to
fortlessly through aluminum up to 18ga. and steel up to 16ga, while painted, plated, or polished surfaces! As it cuts, the SuperSnip con-
the curved handles keep your hands away from the work surface to veniently snips off the waste curl so that it does not build up and
minimize fatigue and possible injury. interfere with your progress; and a built-in guard prevents the cut-off
No. 9L............................. (Left and straight) ......................... $14.95 waste from flying up and into the eyes. The SuperSnip makes straight
No. 9R ...........................(Right and straight) ........................ $14.95 or curved cuts in up to 16 gauge aluminum or 18 gauge steel. Inte-
rior cuts can be made by first drilling a 1/4” hole.
No. J1451............................................................................. $39.95
2 - OFFSET CUTTING SNIPS No. JS1251RB ............... Replacement Blade ......................... $6.95
Maneuvers and cuts easily to very tip of blade. Cuts aluminum, plas-
tics and other thin materials without tearing or catching. Hot drop
8 - HAND NOTCHER
forged from the finest quality high carbon tool steel. Comfortable
vinyl coated handles.
1-800-248-0638
SHEET METAL TOOLS
2 - HAND SEAMER
Jaws are machined smooth, thus eliminating possibility of marring the metal. Throat
depth 1” Jaw width is 3-1/2”. Mfg. by Roper Whitney.
No. A44 ............................................................................................................$42.95
4 - FLUTING PLIERS
Special coating on jaws allows work on aircraft components without marring the sur-
face. Has a 1” reach and will produce a 3/8” flute.
No. FP10...........................................................................................................$15.95
www.aircraft-tool.com
SHEET METAL TOOLS
1 - C-CLAMPS
Forged steel frame - Steel oscillating tip - Siding pin for extra leverage.
2 - SPRING CLAMP
Poly-vinyl jaw-tips protect work area.
No. 3202HT........................................... 2” Reach ..............................................$2.95
5 – AN BOLT GAUGE
All metal gauge designed to accurately determine the sizes and lengths of AN bolts
up to 5/8” diameter. Self-explanatory, easy to use instructions are written directly on the
gauge.
No. AN7..............................................................................................................$9.95
No. BG7................................ Pocket Bolt Gauge 3.75” x 6”...............................$7.95
6 - SCRIBE
Special heat-treated for long, dependable service.
1-800-248-0638
SHEET METAL TOOLS
1 - EDGE MARKING GAUGE
Marking gauge can be used in place of a ruler or adjustable square. Quickly and ac-
curately mark out rivet holes, reference lines on any workpiece. It works as a precision
marking gauge and as a center finder. Precision-cast teeth rack locks the gage in at
exact 1/32” increments.
No. 822 ..............................................................................................................$7.95
2 - EDGE SCRAPER
Ideal for deburring sheet metal edges. Special guard protects users hand.
No. SP201...........................................................................................................$9.95
4 - BURNISHING TOOL
Designed to remove surface blemishes in aircraft sheet metal. Comfort grip handle.
No. 515 ..............................................................................................................$9.95
7 - HAND CRIMPER
New 5 blade style crimps more evenly, has 1-1/4” jaw depth. Full 20 ga. capacity O.A.L.
9”.
No. C-1 ............................................................................................................$19.95
No. SC-1........................................... (Single Crimp).........................................$18.95
www.aircraft-tool.com
SHEET METAL TOOLS
1 - HAND NIBBLER
Improved nibbler design provides maximum comfort and ease of use. The extra long
handles (7”) delivers enough force to easily cut through 18 ga. (.046”) aluminum, steel,
or plastic. The punch action of the nibbler makes it flexible enough to cut any shape
ranging from a straight line down to a 5/16” radius circle. Simply drill a 3/8” starting hole
and insert the punch and begin cutting by squeezing the handles together to remove
material one slug at a time. That’s all there is to it. Your cuts will be clean and com-
pletely burr-free. Ideal for creating access areas, instrument holes, lightening holes, and
other applications requiring a clean, accurate cut.
No. 64823 ........................................................................................................$14.95
2 - AIR NIBBLER
Compact yet powerful nibbler will cut up to 18 gauge steel. Ideal for cutting tight cor-
ners and hard to reach areas. Operates at 90 psi.
No. 5598 ..........................................................................................................$99.95
No. 900040 .................................(replacement cutter) ...................................$29.95
5 - AIR SHEARS
PART NUMBER RPM CAPACITY GRIP PRICE
7000 2200 18 ga. Pistol $117.50
7001STR 2200 18 ga. Straight $129.95
6000 2800 18 ga. Pistol $129.95
6001STR 2800 18 ga Straight $129.95
1-800-248-0638
SHEET METAL TOOLS
1 - BENCH BENDER BRAKE
Bends and forms up to 90° in metals up to 18 gauge thickness. Provides flanged edges
up to 1” in height. Adjustments for stock thickness, sharpness of bends are easy to
make. Note: requires the use of two C” clamps (not included)
www.aircraft-tool.com
SHEET METAL TOOLS
1 - TENNSMITH BENDER BRAKE 4’, 8’ & 10’
Tennsmith brakes are the industry standard. Their rugged construction and precise
control makes them the most sought after tool on the market. Their ease of operation
causes less fatigue and boost operations efficiency. FOB shipping point.
WIDTH WEIGHT
PART NUMBER FINGERS CAPACITY PRICE
(Inches) (Lbs)
48 48 120 None 22ga. (.030) $600.00
U48 48 280 16 22ga. (.030) $765.00
HBU48-16 48 490 15 16ga (.060) $1225.00
HB97-18* 96 1385 None 18ga (.048) $3050.00
HB121-16* 120 2875 None 16 Ga. (.060) $5050.00
B48 Optional Stand (for use with 48, U48, & HBU48) $140.00
*Floor models
1-800-248-0638
CABLE & WIRE
MILBAR® SAFETY WIRE PRODUCTS
www.aircraft-tool.com
CABLE & WIRE
4 - AERO SafTblock
Designed to let your drill safety wire holes in bolts on center without damage to the bolt
or drill. Just thread the bolt to the required depth and drill through the pilot hole. Cre-
ates a perfect hole every time. Accepts sizes 8-32, 10-32, 1/4x20, 1/4x28 and 5/16x24.
Made in the USA.
No. MT001........................................................................................................$18.95
5 - NUT SafTblock
Special design enables you to drill safety wire holes through the head of bolts or through
nuts, across the diagonal. Accepts up to 3/4 inch diameter nuts and bolts. Easy to use,
just place the bolt head into the “V” groove, tighten the holding screw, drill and deburr.
Made in the USA.
No. MT002........................................................................................................$22.95
6 - SAFETY WIRE
Stainless steel annealed, used to secure bolts, nuts or hardware subject to vibration.
Comes in no waste 1 lb. dispenser cans. Type 302. MS-20995C; MIL-w-6713.
1-800-248-0638
CABLE & WIRE
No. C8............................................................................................................$675.95
3 - CABLE TENSIOMETER
This tool combines low cost with high quality and accuracy. It’s a direct reading tensi-
ometer that’s compact enough to fit through inspection holes.
www.aircraft-tool.com
CABLE & WIRE
LOOS & CO. CABLE PRODUCTS
PART
DESCRIPTION PRICE
NUMBER
Complete kit which includes all of the items listed below.
M1-K $4,595.95
Shipping weight 64 lbs.
Swaging machine only with case, Feed Guide Assembly,
M1 $1,970.95
& Feed Guide Adapters
M1-B2 1/16” Ball Terminal Die $425.95
M1-B3 3/32” Ball Terminal Die $425.95
M1-B4 1/8” Ball Terminal Die $425.95
GAB24 Ball Terminal Gauge (1/16”-1/8” cable) $99.95
M1-S2 1/16” Straight Terminal Die $340.95
M1-S3 3/32” Straight Terminal Die $340.95
M1-S4 1/8” Straight Terminal Die $340.95
M1-S5 5/32 Straight Terminal Die $340.95
M1-S6 3/16” Straight Terminal Die $340.95
GAS26 Straight Terminal Gauge (1/16”-1/8” cable) $99.95
3 - HAND SWAGER
Multi-compression hand swager with cable cutter. Swages 1/16”, 3/32”, 1/8”, 5/32”, and
3/16” oval and stop sleeves, plus 7/32” stop sleeves, total of 11 sizes plus the ability to
cut up to 7/32” diameter aircraft quality steel cable (1SC only). A tool with a dozen func-
tions! Only 26” long. Shipping wight 6.5 lbs.
No. 1SC .............................. LOOS & CO. LOCOLOC® model.........................$219.95
No. 64CGMP ...................................... GBG model ........................................$169.95
4 - BENCH SWAGER
For in-shop one location jobs. Multi compression jaws swag 1/16”, 3/32”, 1/8”, 5/32” and
3/16” oval and stop sleeves plus 7/32” stop sleeves. 22.5” long, 6.25” high. Shipping
weight 6.6 lbs.
No. 1BSC ............................ LOOS & CO. LOCOLOC® model.........................$325.95
No. B64-CGMP ................................... GBG model ........................................$295.95
1-800-248-0638
CABLE & WIRE
1 - HAND SWAGER
Ideal for quick swaging of nicopress sleeves onto cables. The #2 swager will do 1/16”,
3/32”, and 1/8” cables. The #3 swager is for 1/8”, 5/32”, 3/16” and 1/4” cables. A Go-
No-Go Gauge is included with both the 2SKT and 2.
No. 2SKT .......................Complete Kit with thimbles and Sleeves ....................$22.95
No.2 ..................................... For 1/16”, 3/32” & 1/8” Cable.............................$15.95
No. 3 ................................ For 1/8”, 5/32”, 3/16” & 1/4” Cable.........................$59.95
No. 54-11 .......................................Go-No-Go Gage ........................................$3.95
3 - SWAGER GAUGE
Checks your cable swages to see if they meet acceptable standards. Measures sizes:
1/32”, 3/64”, 1/16”, 3/32”, 1/8”, 5/32” and 3/16”.
No. GA1P..........................................................................................................$10.95
www.aircraft-tool.com
PRECISION MEASURING
FOWLER CALIPERS
1 - VERNIER CALIPERS 4 - ELECTRONIC CALIPERS
52-058-016
52-057-004
• Patented ceramic capacitive sensor.
• Large easy-to-read LCD display.
• Resolution to .0005”/01mm. • 4” model includes leatherette case.
• Fine quality vernier calipers are constructed of stainless steel. • Direct inch/metric conversions. • 6” & 8” models includes hard case.
• 52-057-004 offers 3-way measurement to .001” accuracy.
• 52-058-XXX series offers 4-way measurement in both inch and metric. PART NO. RANGE ACCURACY PRICE
PART NO. RANGE GRAD FEATURE PRICE 54-100-004 0–4”/100mm .001”/.02mm $68.95
54-100-006 0–6”/150mm .001”/.02mm $72.95
52-057-004 0-4” .001” Mini pocket caliper $21.95
54-100-008 0–8”/200mm .0015”/.03mm $91.95
52-058-016 0-6” .001”/.02mm Fine adjusting $32.95
52-058-008 0-8” .001”/.02mm Fine adjusting $49.95
52-058-012 0-12” .001”/.02mm Fine adjusting $76.95
5 - EURO-CAL III® ELECTRONIC CALIPERS
with “Sylvac Capacitive Measuring System”
2 - ECONOMY DIAL CALIPERS
1-800-248-0638
PRECISION MEASURING
FOWLER MICROMETERS & MEASURING SETS
1 - ECONOMY OUTSIDE MICROMETERS 4 - TOOLMAKER UNIVERSAL MEASURING SET
• .0001” reading
• Carbide tipped anvils
• Ratchet thimble and locking nut
• Microfine graduations
• Includes standards on sets and
sizes over 1”
• Also includes wrench and fitted
case
PART NO. RANGE GRAD PRICE Set includes: 6” Dial caliper - .001” graduations; 0-1” Outside micrometer -
.0001” graduations; and a 6” Flexible rule with 32nds, 64ths, 10ths, & 100ths
52-229-201 0-1” .0001” $18.95
graduations. All contained in a fitted, shop-hardened case.
52-229-202 1-2” .0001” $24.95
52-229-203 2-3” .0001” $29.95 No. 52-095-007.................................................................... $69.95
52-229-213 0-3” set of 3 micrometers plus case $72.95
• Digital counter
• Resolution: .0001” (using vernier)
• Microfine graduations on satin
chrome.
• Carbide tipped measuring
faces.
• Positive locking nut on spindle.
• Sizes over 1” supplied with stan-
dards.
• Resolution: .00005”/.001mm
• Automatic switch off.
• Direct RS232 output.
• Carbide measuring faces.
• Includes case and wrench.
• Oil & fluid resistant to IP54.
• Standards included with set &
sizes over 1”.
• Complete in fitted case.
• Caliper protected to IP65 and Micrometer protected to IP54
standards.
PART NO. RANGE GRAD PRICE • 0-6”/150mm Ultra-Cal IV Caliper - .0005”/.01mm resolution.
54-860-001 0-1” .0001” $82.95 Direct RS232 output and direct inch/metric conversion.
• 0-1” IP54 Electronic Micrometer - .00005”/.001mm resolution, Auto switch
54-860-002 1-2” .0001” $99.95
off, and carbide measuring faces
54-860-003 2-3” .0001” $119.95 • 4R steel rule.
54-860-103 0-3” set of 3 micrometers plus case $299.95 No. 54-004-854.................................................................. $229.95
www.aircraft-tool.com
PRECISION MEASURING
Universal Mag Base: Locking screw and two Magnetic Base Features:
universal ball sockets for setting at any angle • 85 lb. pull.
position. Microfine adjustment screw. Remov- • Fine adjustment
able extension arm. Dovetail formholder Extra Points • V-bottom base.
with locking control to hold dovetail test
.040" .120"
indicators. Accepts .250” diameter test
indicator stems.
No. 52-566-003.................................................................... $64.95 No. 52-585-110.................................................................... $45.95
1-800-248-0638
PRECISION MEASURING
1 - TELESCOPING GAUGES 4 - FOWLER 10X ILLUMINATED OPTICAL COMPARATOR
www.aircraft-tool.com
PRECISION MEASURING
1 - RADIUS GAUGES 5 - CENTER FINDING RULE
Precision ground gauges
are used to check layouts
and radii. Each has a
Ideal for laying out equally spaced holes or finding the center be-
concave and a convex ra-
tween two points. The zero mark is in the middle of the rule and is
dius. Stamped radius size on
graduated equally to either side of the center. One side is graduated
each lead. All gauges have
in 8th, 16th, 32nd, and 64th inches. Width is 1” and length is 12”.
a locking device.
No. 1210CF ............................................................................ $6.95
PART NUMBER SIZE GRAD PRICE
52-470-100 1/32”-1/4” 64th $22.95
52-470-102 17/64”-1/2” 64th $29.95
52-470-120 1/32”-17/64” 64th $21.95 6 - ULTRA RULE™ PRECISION MARKING PROTRACTOR
52-470-121 9/32”-33/64” 64th $23.95 A precision protractor with micro-
fine guide holes at every 45º, 30º,
22.5º, 5º, 1º, and .5º interval to
accurately plot any angle. See
through crosshairs provide exact
2 - ULTRA RULE™ CENTER FINDING RULE
alignment against the edge of
your workpiece. Remove the T-
Bar to work on flat surfaces or to
use the 6” centering rule, which is
graduated in 1/32”.
A flexible, stainless steel center-finding rule with micro-fine top and
No. 30 .................................................................................. $21.95
bottom guide holes every 1/32” to accurately locate points. Use it to
plot perfectly symmetrical marks from the exact center of any work
piece up to 12” wide. Length is 12” graduated in 1/32” increments.
No. 1211 .............................................................................. $15.95
7 - ULTRA RULE™ PRECISION MARKING RULES
8 - EZ READ RULES
PART NO LEN WID GRAD PRICE PART NO. LEN WID GRADS PRICE
52-340-006 6” 3/4” 32nd, 64th, 10th, 100th $6.95 EZ6 6” 1/2” 10th, 100th, 32nd, 64th $7.25
52-340-012 12” 1-1/8” 32nd, 64th, 10th, 100th $11.95 EZ12 12” 1/2” 10th, 100th, 32nd, 64th $11.50
52-340-018 18” 1-1/8” 32nd, 64th, 10th, 100th $21.95 EZ18 18” 3/4” 10th, 100th, 32nd, 64th $20.95
52-340-024 24” 1-1/8” 32nd, 64th, 10th, 100th $34.95 EZ24 24” 3/4” 10th, 100th, 32nd, 64th $28.95
1-800-248-0638
PRECISION MEASURING
1 - SMARTTOOL™
The SmartTool™ digital electronic level delivers precise angular readings. Reads all
angles • Bubble vials for level and plumb • Digital display reads in degrees, % slope,
pitch • Up to 1/10 degree accuracy • “Beeps” at level and plumb • Easy push button
calibration • Dirt and water resistant.
No. 92288 ............................................ (24” unit)...........................................$119.95
No. 92296 ............................................ (48” unit)...........................................$135.95
4 - ANGLE FINDER
Measures Angle Pitch (forward or backward). Magnet in base holds tool in place.
No. 6494KD ......................................................................................................$16.95
5 - WIRE GAUGE
American National Standard wire gage 0 to 36, used for gauging non-ferrous wire and
metals such as aluminum, copper, and brass.
No. 20 ..............................................................................................................$16.50
www.aircraft-tool.com
TEST & INSPECTION
1-800-248-0638
TEST & INSPECTION
2 - INSPECTION MIRRORS
All angle ball joint. Insulated vinyl grip.
3 - STEELMAN BEND-A-LIGHT
Bend-A-Light is a flexible high intensity light that bends to any configuration and illumi-
nates hard-to-reach areas where conventional lighting cannot go. 6-piece professional
model comes complete with flexible light, pocket light, angle mirror, pickup magnet,
extension shaft, and a carrying pouch. Made in U.S.A.
No. 10309 ................................. (10” Pro Kit with pouch) .................................$35.95
No. 16102 ..........................................(5” Mini-Pro) ..........................................$14.95
5 - BRIGHTEYES PRO-LIGHT
The perfect solution when you need a flashlight, but you need both hands free. The
Brighteyes Pro places two high-intensity beams wherever you look and allows both
hands free to work. May be worn over regular eyeglasses. Batteries included.
No. 80205 ........................................................................................................$12.95
www.aircraft-tool.com
TEST & INSPECTION
1-800-248-0638
TEST & INSPECTION
www.aircraft-tool.com
TEST & INSPECTION
2 - DIGITAL PROTRACTOR
Instantly measures any angle from 0 to 60 degrees to an accuracy of 0.1 degree. A
thousand times easier to use over the old method. Alternate reference feature for quick
and accurate measurement of deviations from reference surface. Hold button freezes
the display angle. Includes 9V battery. Dimensions are 5-1/2”x3”.
No. KS5490.....................................................................................................$395.95
1-800-248-0638
ENGINE EQUIPMENT
HELI-COIL®
www.aircraft-tool.com
ENGINE EQUIPMENT
CHAMPION® ENGINE PRODUCTS
1- BENCH TOP GAP SETTING TOOL
A precision gap-setting tool for all massive-electrode spark plugs. Permits simultaneous
adjustment of two opposite prongs without removing the spacing gauge. Designed
for permanent installation on bench. Includes spacing gauge and spacing gauge
handle assembly. Wt: 5-1/2 lbs.
No. 2500A ......................................................................................................$245.95
2 - VIBRATOR CLEANER
The Champion vibrator cleaner is designed to clean massive electrode or fine wire
spark plugs that accumulate heavy lead-compound deposits. Such deposits are virtu-
ally impossible to remove with standard abrasive cleaners. Wt. 7 lbs.
No. 2600A ........................................... 110V 60Hz..........................................$475.95
No. 2600AX ......................................... 220V 50Hz..........................................$499.95
No. PA01-1 .................................. Replacement Blade ......................................$1.95
7 - LEAD-MASTER WRENCH
Lead-Master wrenches reduce time to remove and install spark plug ignition leads, also
permits short arc turning due to 12-point grip head. Wt. 9oz.
No. CT913 ........................................................................................................$56.95
1-800-248-0638
ENGINE EQUIPMENT
CHAMPION® ENGINE PRODUCTS
1- SPARK PLUG TRAY
A sturdy steel tray that holds up to 12 aviation spark plugs. Speeds handling of used or
new plugs. Holes are numbered to correspond with engine cylinders. Protects against
shielding barrel contamination. Flat rubber, non-slip pads. Wt. 1 lb.
No. CT446 ........................................................................................................$32.95
6 - THREAD CHASER
For cleaning aircraft engine spark plug 18mm holes to ensure correct installation of
new or overhauled spark plugs. Regular 7/8” hex fits spark plug sockets. It has precision
ground threads and three deep flutes to retain deposits. Wt. 7oz.
No. CT449 ......................................................................................................$119.95
www.aircraft-tool.com
ENGINE EQUIPMENT
EASTERN TECHNOLOGY
1-800-248-0638
ENGINE EQUIPMENT
www.aircraft-tool.com
ENGINE EQUIPMENT
1-800-248-0638
ENGINE EQUIPMENT
www.aircraft-tool.com
ENGINE EQUIPMENT
1-800-248-0638
ENGINE EQUIPMENT
A precision tool that will allow you to remove broken studs, retap,
Designed for the professional mechanic, the Silverline Test Kit is the and replace them accurately to the original dimensions. This can
premier member of the Mityvac line. The repairable vacuum pump be accomplished in most cases without removing the cylinder; even
is made of zinc alloy die cast metal with an easily readable vacuum Number One in a Bonanza, Works on all Continental 470, 540, 550,
gauge graduated in inches of mercury. The complete kit includes: and 520 series engines. The kit includes the following:
the Silverline vacuum pump, reservoir jar and transfer lid, storage lid, • One steel, jig bored, locating plate
brake bleeding adapter package, test adapter package, 1-1/4” rub- • Three knurled retaining nuts to secure the locating plate
ber cup adapter, two 24” lengths of 1/4” tubing, carrying case with • Four hardened and ground drill bushings
removable lid, and a 100 page manual. • Three drill extensions: 6”, 9”, and 12”
No. 4000 .............................................................................. $69.95 • One 3/8” drill chuck
No. HE01 ............................................................................ $149.95
No. 1122 .......................... 2” Max Spread ........................... $28.95 No. 870K ............................................................................. $55.95
No. 1123 ....................... 4-5/8” Max Spread ........................ $53.95 No. 872K ..................... (replacement cutter) ...................... $14.95
www.aircraft-tool.com
ENGINE EQUIPMENT
9 - LAPPING COMPOUND
1-800-248-0638
ENGINE EQUIPMENT
This economical cutter quickly opens any size oil filter canisters for
filter inspection. Simply place the filter in a vise, attach the tool to the
top, and rotate about 4 to 6 turns to cleanly cut open the canister. It’s
made of high quality 6061 aluminum with an attractive purple anod- For all flange shafts per Continental Bulletin M-70-2. Also fits Lycom-
ized finish. The cutting wheel stays sharp for up to 45 applications, ing. For installing one piece stretch seals easily and efficiently without
and is easily replaced when it becomes dull damaging the seal or crankshaft.
FC01 ................................ (oil filter cutter) ........................... $45.95 No. 5209 .............................................................................. $79.95
FCW ..................... (replacement cutting wheel) .................. $6.95
6 - SEAL PULLER
2 - OIL FILTER CUTTER
www.aircraft-tool.com
ENGINE EQUIPMENT
1-800-248-0638
ENGINE EQUIPMENT
TIME-RITE®
Time-Rite has been the number one choice of aviation mechan-
ics for over 40 years when it comes to precisely timing engines. By
using specialized arms and calibrated scales, Time-Rite accurately
displays piston position and angular displacement to within 1 degree
accuracy on just about every make of aviation piston engines. No
other instrument has come close to matching the versatility, simplic-
ity, and accuracy of Time-Rite.
Aircraft Tool Supply Company is the proud manufacturer of Time-
Rite®, and it’s completely manufactured, assembled and serviced
at our plant here in the U.S.A.
The basic Time-Rite unit (I200B18 & I200B14) does not include any Part No. Description Price
arms or scales. You must purchase these separately for the specific I200B18K Complete 18mm Time-Rite Kit $499.95
type of engine you intend to service. The complete Time-Rite kits
I200B14K Complete 14mm Time-Rite Kit $399.95
(I200B18K & I200B14K) includes the basic unit plus the complete set
of Arms and Scales. I200B18 Basic 18mm Time-Rite Unit $250.95
I200B14 Basic 14mm Time-Rite Unit $250.95
ENGINE ENGINE TIME Engine Scale: specify the desired
SCALE ARM U/D I209-X $12.95
MAKE MODEL RITE scale when ordering e.g. I209-5A
ALLISON V-1710-143, -145 B18 12 H Dn.
Engine Arm: specify the desired
I205-X $19.95
A SERIES B18 5B D Up arm when ordering e.g. I205-D
C-75, C-85, C-115, C-125 B18 5A C Up
6A6-245, 6A8, 6V6-245, O-425-1, 5, 9 B14 8A R Dn. GIPSY QUEEN 30MK.2 & 70 MK.2 B14 25A C Dn.
ROLLS-ROYCE
JACOBS L4, R755A B18 6B C Dn. GIPSY MAJOR 140 B14 28A D Up
O-235, 0-290-11, O-320, A, C, E, WARNER 125, 145, 165, 185 B18 6A C Dn.
O435-17, 23, O-480-1, A1, A6, GO-435,
VO-435, GO-480-A1, A6, B, B6, D, F, F6, R-1820-54, 72 WA, 60, 62, 62A, 74W, 76,
B18 9B E Dn. 76A, 76B, 76C, 76D, 80, 80A, 82, 82A, 84,
GO-580, GSO-480-A1A6, B1A6, B1B6, B18 2B B Up
GSO-580, IGSO-480-A, A1, A6, B6, IO- 84A, 84C, 84D, 86, 86A, 97, 101, 103,
320A TVO-435, TVO-435-B1A 103A, C9GC, C9HD, C9HE (805940)
O-340-A, O-290-D2B, O-290-D2C B18 18B V Dn. R-2600-8, 13, 20, 29, C148B, R-3350-8,
LYCOMING 13, 23A, 24W, 24WA, 35, 35A, 57M, 57AM, B18 2A B Up
GO-480C, C1B6, C2D6; G2D6; GO-480- 83; 745C18BA-3 (805940)
B18 19 E Dn. WRIGHT
C1D6; GO-480-C2C6
R-3350-26W, 26WA, 26WB, 30W, 30WA,
IMO-360-A, O-360A, A1A, VO-360, MO- 30WB, 32W, 34, 77, 85, 89, 91 (805942),
B18 14B M Up
360, IGO-540, O540-A, A1A; VO-540, B18 18A D Up 861C18CA-2, 956C18CA, 927TC18DA-1,
IGSO-540, HIO-360B, 0-340-A1A 2, 3, 4; 975C18CB-1, 988TCl8EA-1, 2, 3
www.aircraft-tool.com
SERVICE & SUPPORT
MEYER HYDRAULICS® AIRCRAFT JACKS
AJS UNIVERSAL AIRCRAFT LIFT SYSTEM (17 PC. SET)
This universal jack set will handle most light aircraft (see list below). Sets include two
(2) A5 jacks with AT-1 slide tube, two (2) A6 jacks with AT-2 slide tubes, two (2) sets of
AJL extension leg s, one (1) ATS adj. tail stand, two (2) AT-3 slide tubes, two (2) AT-4
slide tubes, two (2) ATC-4 Extension Caps, and two (2) AT-5 Extension Caps. All Meyer
Jacks feature positive pin safety locks, spring loaded casters and special Meyer
locking device to eliminate motion when aircraft is elevated. FOB SHIPPING POINT
No. AJS ..................................................................................................$2,199.95
Grumman A-13 2 wing 42” 75” Cessna: All high wing (2) AT-4
RGs except (2) A-6 (1) ATS (2) AJL
Gulfstream A17 1 nose 34” 60” (2) ATC-8
Cardinal
Merlin II, III, & IV A-13 3 42” 75”
Cessna: 310, 320, 401,
Jet Commander Westwind A-17 2 34” 60” (2) A-5
402, 411, 414, -- -- (2) AT-28
(2) A-6
A-60 2 wing 60” 100” 421
Mitsubishi MU-2
A-6 1 nose 34” 58” Navion (2) A-5 (1) ATS - (2) AT-28
Turbo Commander A-60 2 wing 60” 100”
ACCESSORIES
JACKS Part No. Description Price
Part No. Description Price AJL Extension Legs (set of 4), 10”, for A6 $59.95
A-5 Aircraft jack, 22”, 3 Ton, w/AT-1 $400.95 ATS Aircraft Tail Stand, 30” to 51-1/2” $115.95
A-6 Aircraft jack, 34”, 3 Ton, w/AT-2 $476.95 AT-1 Slide Tube, 22” low, for A5 $30.95
A-9 Jet jack, 28”/46”, 8 Ton $975.95 AT-2 Slide Tube, 34” low, for A6 $32.95
A-10 Jet Jack, 22”/36”, 5 Ton $950.95 AT-3 Slide Tube, 34” low, for A5 $36.95
A-11 Jet Jack, 30”/50”, 5 Ton $995.95 AT-4 Slide Tube, 54” low, for A6 $45.95
A-13 Jet Jack, 42”/75”, 8 Ton $1150.95 ATC-4 Tube Cap, 1- 4”, for AT-6, AT-28, AT-3, AT-4 $31.95
A-17 Jet jack, 34”/60”, 8 Ton $995.95 AT-6 Slide Tube, 26” low, for A5 $37.95
A-60 Jet jack, 60”/100”, 5 Ton $1,125.95 AT-28 Slide Tube, 28” low, for A5 $42.95
A-2516 Jet Jack, 25”/42”, 8 Ton $995.95 ATC-8 Tube Cap, 1” to 8”, for AT-28, AT-3, AT-4 $40.95
1-800-248-0638
SERVICE & SUPPORT
SEMCO® PRODUCTS
2 - HOSE ASSEMBLY
All hose assemblies come with a B-nut fitting to attach to the Semco gun and the speci-
fied quick connect attachment. Each hose is 5 ft (1.5m) long.
No. PRC-5A......................... (with ARO quick-connect fitting)...........................$29.95
No. PRC-5H ..................... (with HANSEN quick-connect fitting)........................$29.95
No. PRC-5S .................... (with SCHRADER quick-connect fitting)......................$29.95
www.aircraft-tool.com
SERVICE & SUPPORT
1-800-248-0638
SERVICE & SUPPORT
FITTING THREAD
PART NUMBER HOSE SIZE PRICE
NUMBER SIZE
2701-3 -3 300-3 3/8-24 $16.95
2701-4 -4 300-4 7/16-20 $16.95
2701-5 -5 300-5 1/2-20 $16.95
2701-6 -6 300-6 9/16-18 $20.95
2701-8 -8 300-8 3/4-16 $21.95
2701-10 -10 300-10 7/8-14 $29.95
2701-12 -12 300-12 1-1/16-12 $32.95
2701-KIT All mandrels listed above plus case $149.95
www.aircraft-tool.com
SERVICE & SUPPORT
1 - BEADING TOOL
The new ATS Beading Tool does everything the old Parker did at a price you can live with.
It forms perfect beads in aluminum, copper, and soft steel tubing just as effortlessly as
the old Parker tools. Best of all, it’s only a fraction of the price. The complete kit includes:
tube holder, die holder, beading dies (#4, #6, #8, #10, #12, and #16), instructions,
and carrying case. Not for use with stainless steel. Forms beads in ¼”, 3/8”, ½”, 5/8”,
¾”, and 1” tubing
No. 145A ........................................................................................................$175.95
3 - TUBE BENDER
Special nylon forms prevents kinking or flattening. Easy to use with one end of the tube
connected, or the unit can be mounted in a vice. For 3/16”, 1/4”, 5/16”, and 3/8” O.D.
tubing. Not recommended for 3/8 steel.
No. 44000 ..........................................................................................................$9.95
1-800-248-0638
SERVICE & SUPPORT
www.aircraft-tool.com
SERVICE & SUPPORT
5 - BLOW GUN
Meets OSHA standards as to maximum PSI and noise level
No. D420............................................................................................................$3.50
1-800-248-0638
SERVICE & SUPPORT
1 - SWIVEL CONNECTOR
Eliminates twisted air hoses forever. This connector swivels 360° and keeps your air hose
straight no matter how your tool is held. Screws into any 1/4” NPT air tool. It can be used
with quick disconnect couplers. Patent pending.
No. 2563 ..........................................................................................................$10.95
2 - AIR REGULATOR
Proper air pressure and air flow are a must when operating air tools and when painting.
Screws into any 1/4” NPT fitting. 160 PSI gauge.
No. 1370 ............................................................................................................$9.95
6 - AIR REGULATOR
Fits any tool with 1/4” thread.
No. 5401 ............................................................................................................$5.95
www.aircraft-tool.com
SHOP EQUIPMENT
Removes Sizes
Part No. Price
English Metric
P401S 1/4”, 5/16”, 3/8”, 1/2” M6, M8, M10, M12 $54.95
P450S #5 Through 1/4” M3, M4, M5, M6 $36.95
P701S #5 Through 1/2” M3 Through M12 $74.95
1-800-248-0638
SHOP EQUIPMENT
1 - SCREW-GRAB®
Screw Grab® is a remarkable product that has to be seen to be believed! Just a drop or
two placed onto the head of a stripped screw or rounded bolt will increase the torque
by up to 400% and allow you to easily tighten or remove them. It works effectively on all
type of screws including slotted, phillips, apex, torx, tri-wing, etc. The special emulsion
will not stain or react chemically, and it wipes easily and completely from any surface.
Keep a bottle handy and you may never have to resort to screw extractors again.
No. SG94................................................(.5fl oz) ................................................$4.95
www.aircraft-tool.com
SHOP EQUIPMENT
1-800-248-0638
SHOP EQUIPMENT
1 - ELECTROSONIC CLEANER
Electrosonic cleaning is the method of choice when ultrasonic cleaning may damage
parts being cleaned. The unit consists of a solid, stainless steel tank, 11-1/2” x 5-1/2” x
5-1/2”. Parts are safely and thoroughly cleaned as the vibrator motor gently agitates
the cleaning solution. The stainless steel tank can withstand even the harshest cleaning
solutions.
No. KS5518A............................................ 115V..............................................$449.95
No. KS5518E ............................................ 220V..............................................$595.95
5 - SAND BLASTER/FINISHER
Comes complete with dust collectors, rubber gloves, light, nozzle and view window.
Work area is 36”x24”. Requires 80 PSI. FOB Shipping Point.
www.aircraft-tool.com
SHOP EQUIPMENT
1 - DELTRAN BATTERY TENDER®
It’s been called the world’s most advanced battery charger: The award winning Del-
tran Battery Tender is one of the new generation of “smart” chargers. It is designed to
fully charge your battery and maintain it at proper storage voltage without producing
any of the damaging effects caused by trickle chargers. Its microprocessor circuitry
constantly monitors your battery’s state and controls the charging so that it does not
overcharge and “cook” your battery. Just plug it in and forget it! Battery Tender is the
charger recommended by companies such as AC/Delco, Harley-Davidson, BMW Au-
tomotive, Polaris, and many others. Comes equipped with a handy Quick Connect
Harness. Two year warranty.
No. 021-0069 ............................... 12V Battery Tender .....................................$59.95
No. 021-0112 ............................... 18V Battery Tender .....................................$59.95
No. 022-0086 ............................ 24V Onboard Charger ..................................$89.95
1-800-248-0638
HAND TOOLS
An all-purpose tool that will strip and cut wires, crimp terminals, and
cut bolts. The stripper section will strip: 22-20, 18, 16, 14, 12, & 10 An excellent tool for picking up steel parts in hard-to-reach areas.
AWG wire. Crimps insulated and non-insulated terminals in sizes: 22- Magnetic tip is a high power neodymium (rare-earth) magnet with a
14, 12-10 AWG. The bolt cutter section will cut bolt sizes: 4-40, 6-32, pulling force of over 2 lbs. Overall length is 20”.
8-32, and 10-32. Features Milbar’s Air-Pocket cushion grips.
No. 395 .................................................................................. $5.95
No. 18E ................................................................................ $14.95
www.aircraft-tool.com
HAND TOOLS
A convenient spring tension, self opening tool for punching round No. 2X772 .............................................................................. $3.95
holes in leather, plastic, rubber, canvas and similar materials. Punch-
es holes: 5/65”, 3/32”, 7/64”, 1/8”, 5/32”, & 3/16”
No. 722 .................................................................................. $7.95
7 - E-Z SCREWDRIVER
3 - IMPACT DRIVER
1-800-248-0638
HAND TOOLS
2 - CANTILEVER TOOLBOX
Extra large chest has four trays that automatically swing wide for access to big storage
area beneath. Two trays are divided into five compartments each; one tray has a
socket divider. Heavy duty construction includes sturdy tray supports. Size: 20”L x 9-
1/2”W x 10”H.
No. 2W024 .......................................................................................................$79.95
4 - PROFESSIONAL TOOLBOX
An exceptionally well-constructed toolbox that is ideally suited for the professional me-
chanic who needs a well-organized toolbox. The three sliding drawers are perfect for
foam-mounting tools so that they are easily accessible. The overall dimensions of the
toolbox are: 22” wide x 9-1/2” deep x 12-3/4” high, and the drawers are 20” wide by 8”
deep by 2-1/8” high. 26 lbs shipping weight.
• Reinforced double-wall construction
• Welded reinforcing braces for extra rigidity
• Baked on scratch-resistant powder finish
No. 9031 ..........................................................................................................$75.95
5 - TRI-WING® BITS
Genuine Tri-Wing® bits are hot formed for optimum toughness and resistance to wear.
Each bit is 1” long and has a ¼” hex shank that will fit into most screwdrivers.
www.aircraft-tool.com
HAND TOOLS
1 - TORQUE SCREWDRIVER
A high precision tool that delivers the exact amount of torque to a screw or bolt every
time. The unique auto release mechanism disengages the driver after a pre-deter-
mined torque has been reached and then automatically resets itself so that you can
work continuously without re-adjusting the tool each time. Right handed operation only.
Accuracy of +/- 4% on readings at or above 20% of maximum scale. Meets ANSI stan-
dard B107.14M. Includes a fitted case
2 - COMPASS SCREWDRIVER
Solid brass screwdriver with a small flat blade that is designed for the adjustment of
magnetic compasses.
No. 906 ..............................................................................................................$7.95
6 - SCREW STARTER
For starting phillips or common screws in out of reach areas or when screws are too
small to hold while threading. The spring tension chuck firmly holds the screw in place
until you release it. 8082
PART NUMBER DESCRIPTION PRICE
8082 Slotted starter 3/64” - 7/6” screws $6.95
8083 Phillips starter #6 - 1/4” screws $6.95 8083
1-800-248-0638
HAND TOOLS
www.aircraft-tool.com
HAND TOOLS
1 - WIRE BRUSHES
Used to remove rust scale, paint, solder, clean threads, files, metal parts and castings. (a)
Wood handles with high carbon steel wire.
4 - COMPOSITE FILE
New product for composite and fiberglass designs. Designed to file and shape con-
tours or edges. Easy to clean for reuse.
No. FR85-T010 ..................................................................................................$25.95
1-800-248-0638
POWER TOOLS
1 - DIE GRINDERS
A compact, lightweight grinder with enough power for all grinding, polishing, and buff-
ing applications. Features a reverse exhaust port to direct air away from work. Shipping
weight is 1.3 lbs.
• 22,000 rpm at 1/2 hp • Reverse exhaust
• 1/4” collet size • 1/4” NPT inlet
• Operates at 90 psi (4 cfm) • Ball Bearing construction
PART NO. DESCRIPTION PRICE
SX230A Straight Grinder (6-3/4” long) $49.95
SX232A 90 degree angle grinder (6” long) $75.95
3 - AIR SCREWDRIVER/IMPACT-NUTRUNNER
Versatile impact driver can be used as a nutrunner or a screwdriver. All ball bearing con-
struction. Reversible. Wt. 2 lbs. Develops 30-60 ft-lbs. of torque at 1800 RPM. 1/4” drive.
No. 2005 ........................................................................................................$139.95
Torque
Part No. Drive Style RPM Price
(ft-lbs)
SX834 1/2” Pistol (a) 8000 400 $99.95
(a) (b)
SX826 3/8” Pistol (a) 10,000 75 $69.95
SX201 3/8” Pistol (a) 10,000 50 $89.95
SX111 3/8” Str. (b) 11,000 40 $69.95
SX300 3/8” Offset (c) 160 60 $69.95 (c)
5 - SANDERS
New designed model 294 is a dual action sander. Operates on 4 CFM and comes
with built-in regulator. Model 296 is an orbital action sander with sealed ball bearings
for longer life.
www.aircraft-tool.com
POWER TOOLS
2 - PANEL SAW
Cuts up to 3/16” aluminum, 1/4” wood. Accepts 1-3/4 dia. blades. Features retractable
safety blade guard.
No. KS-21AM ..............................(electric, 115V, 4amp) ................................$249.95
No. PS-526....................................... (air, 2200 RPM) ......................................$225.95
No. 157-34 ...................(replacement blades, 44TPI, pkg. or 12) ....................$39.95
No. 157-36 ...................(replacement blades, 60TPI, pkg. of 12) ....................$39.95
1-800-248-0638
BOOKS
www.aircraft-tool.com
ORDER FORM
AIRCRAFT TOOL SUPPLY For faster service...
• USA & Canada call 1-800-248-0638
P.O. Box 370
• International USA+1+989+739-1447
1000 Old U.S. 23 • Fax 1-989-739-1448
Oscoda, MI 48750-0370 USA • Order online www.aircraft-tool.com
You may also make payment by sending us a check or money order with your
order. However, please note that we reserve the right to hold personal checks REPAIR SERVICE
until they are cleared by the bank, which might take up to 5 business days Items requiring repair and no longer covered by our warranty may be re-
We accept COD orders subject to the following limitations: Personal COD or- turned to our repair department. Please include your complete address and
ders are limited to $150 and must be paid by certified funds (money order, or a telephone number at which you may be reached during the daytime. State
certified check) unless otherwise approved by us. First time orders to un-rated the nature of the problem clearly. Please indicate if you require an estimate
companies are limited to $500. Regardless of the value of the order, all COD before repair. Enclose payment information to cover the cost.
110
INDEX
A Electrical Terminal 100 Dead Blow 104
Sheet Metal 54 Rawhide 104
Aircraft Jacks 87 Cylinder Base Wrenches 85 Sheet Metal 48
Air Connector, Swivel 94 Cylinder Bore Gauge 65 Soft Face 104
Air Drills 32, 33, 34 Hand Tools 100–105
Air Filter 94 D Heat Gun 97
Air Hose 93 Heli-Coil® 74
Air Hose Couplers 93 Deburring Tools 4, 38, 54
Deltran Battery Tender® 99 Hex Wrenches 101
Air Manifold 93 Hi-Lok® Tools 1
Air Oiler 94 Depth Gauges 65
Dial Indicators 65 Hi-Shear Tools 19
Air Regulators 17, 94 Hole Cutter 50
Air Tank 93 Die Grinders 106
Differential Pressure Testers 77, 78 Hole Duplicators 37
Angle Finder 68 Hole Gauges, Full Ball 66
Angle Gauge 68 Dimple Dies 20, 21
Dimple Die & Squeezer Set Holder 20 Hole Saw 50
Aviation Snips 51 Holster, Leather 46
Dimple Die Block Set 20
B Dimpling/Riveting Tool 20 Hose Assembly, Semco® 88
Dimpling Pliers 21 Hose Assembly Tool 90
Ball Hole Gauges 66 Dolly, Sheet Metal 49 Huck® Riveters 26
Battery Chargers 99 Drill-Out® Screw Removers 95
Beading Tool 2, 91 I
Drilling Equipment 32–42
Bearing Packer 82 Drills, Air 32, 33, 34 Impact Driver 101
Bearing Separators 82 Drill Attachments 34, 35 Impact Wrenches, Air 106
Bender Brake 2, 56, 57 Drill Bits 40, 41
Blind Riveters 3, 6, 24–28 Drill Chuck 36 J
Blow Gun 93 Drill Collets 37
Bolt Cutter 6 Jacks, Aircraft 87
Drill Extension 36 Jogging Tool, Sheet Metal 55
Bolt Gauge 53 Drill Gauges 38
Bonding Brush 54 Drill Guide K
Books 108 Plate Nut 39
Borescopes 2, 6, 69, 70 Kevlar® Kutter 46
Safety Wire 59
Brake Bleeder Adapters 89 Tube 38
Brake Bleeder Tank 1, 89
L
Drill Housing & Bushings 37
Brake Relining Tools 89 Drill Sets 41 Lapping Compound 83
Brake Rivets 89 Drill Stops 37 Light
Brushes, Wire 105 Duplicating/Transfer Punch 36 Fluorescent 97
Bucking Bars 15 Inspection 57, 70
Burnishing Tool 54 E
Burrs, Carbide 106 M
Eastern Technology Products 77
C Electrosonic Cleaner 98 Mag-Lock 80
Engine Equipment 75–86 Magnaflux® 72
Cable & Wire Tools 58–62 Engine Protector, TopCap 78 Magnetic Field Indicator 72
Cable Cutter 62 Engine Stand 85 Magneto Synchronizers 77, 80
Cable Gauges 62 Engine Test Kit 78 Magnets 100, 101
Cable Rigging Tool 60 Exhaust Stud Drill Guide 82 Marker, Edge 54
Cable Swager 61, 62 Meyer Hydraulics® Aircraft Jacks 87
Cable Tensiometer 60 F Micro-Mesh™ 92
Cable Tester, Ignition 77 Micrometers 64, 65
Cable Thimbles & Sleeves 62 Fabric Tester, Maule 73
Microstop Countersink 29
Calipers, Precision 63 Fabric Tools 46
Mini-Mixer 92
Calipers & Dividers 66 Fiberscopes 2, 6, 69
Mirrors, Inspection 70
Cannon Plug Pliers 99 File, Vixen 47
Multimeter, Digital 71
Carbide Burrs 106 Files & Rasps 105
Cartridges & Nozzles, Semco® 88 Flanging Tool, Hole 54 N
Center Finding Rule 67 Flaring Tools
Push Rod 83 Nibbler, Sheet Metal 55
Center Punch 36 Notcher
Champion® Engine Products 75, 76 Tube 4, 91
Flex Hone 84 Sheet Metal 51, 56
Cherry® Riveters 3 Tubing 50
Cherrymax® Rivets 13 Fluorescent Lights 97
Chip Chaser 38 Fluting Pliers 52 O
Clamps, Sheet Metal 12, 53 Fly Cutter 50
Oil, Air Tool 93
Cleco Fasteners 12 G Oil Filter Cutter 76, 84
Cleco Pliers 12
Gasket Punch 84 Oil Nut Wrench, Cessna 84
Combination Squares 66
Grip Gauge, Cherrymax 13 Oil Seal Installer 84
Composite Tools 47
Optical Comparator 66
Compression Riveters 22, 23
Countersinks & Counterbores 29, 30, 31
H
P
Creeper, Low Profile 92 Hammers
Crimpers Brass 104 P-Lead Adapter, Magneto 80
111
INDEX
Paint Gun 98 S Tennsmith™ Brakes & Shears 56, 57
Perma-Grit® 47 Tensiometer, Cable 60
Pickup Tool 100 Safety Wire 59 Test & Inspection Equipment 69–74
Pinking Shears 46 Safety Wire Twisters 58, 59 3M Products 43, 44, 45
Pin Punches 100 Sander, Belt 107 Tie Straps 96
Piston Ring Compressor 81 Sand Blaster 98 Tie Strap Tool 96
Piston Ring Expander 81 Saws, Air 107 Time-Rite® 86
Piston Ring Filer 82 Scale, Straight 90 Timing Indicator 77
Piston Ring Groove Cleaner 82 Scotch-Brite™ 43, 45 Tire Bead Breaker 89
Piston Ring Installer 81 Scraper 47, 54 Tire Pressure Gauge 89
Plate Nut Drill Jigs 39 Screw-Grab® 96 Toolbag 102
Pliers Screwdriver Toolbox 102
Cannon Plug 99 Air Powered 106 Torque Screwdriver 103
Channel Lock 104 Brass Compass 103 Torque Wrenches 104
Cleco 12 Hand 101, 103 Transfer Punch 36
Dimpling 21 Torque 103 Tri-Wing® Bits 102
Fluting 52 Screw & Bolt Remover 95 Tube Benders 4, 91
Mechanics 104 Screw Remover 95 Tube Cutters 91
Vise-Grip® 104 Screw Starters 103 Tubing Notcher, RTN 50
Polish, Aircraft 92 Scribe 53
Polisher, Orbital 107 Sealant, Aviation Gasket 80 U
Power Tools 106, 107 Sealant Gun, Semco® 88
Seal Driver 84 Ultrasonic Cleaners 5
Precision Measuring Tools 63–68 Ultrasonic Leak Detection Kit 2
Pressure Gauge, Tire 89 Seal Installer 84
Seal Puller 84 Unibit Drill Bits 41
Protractor
Digital 73 Seamer, Sheet Metal 52 V
Marking 66, 67 Semco® Sealant Products 88
Service & Support Equipment 87–94 Vacuum Cleaner, Air 96
Propeller 73
Shears Vacuum Gauge 82
Pulling Head, Riveter 25
Fabric 46 Vacuum Test Kit 82
Punch
Sheet Metal 51, 55, 56, 57 Valve Clearance Gauge 83
Air Powered 55
Sheet Metal Fasteners 12 Valve Guide Cleaner 83
Hand 50, 101
Sheet Metal Gauge 68 Valve Guide Knurlers 83
Push Rod Flaring Tool 83
Sheet Metal Tools 48–57 Valve Guid Flex Hones 83
Push Rod Spring Compressor 83
Shop Equipment 95–99 Valve Lappers 83
R Shot Bag 48 Valve Spring Compressor 83
Shrinker/Stretcher, Sheet Metal 56
Radius Gauges 67 Slapping Spoon 49
W
Reamers 42 Slip Rollers, Sheet Metal 57 Welding Kit 97
Retainer Springs, Rivet Gun 17 SmartTool™ 68 Wingnut Fastener 12
Rivenuts 28 Snips, Sheet Metal 51, 52 Wire Brushes 105
Rivenut Installers 27, 28 Socket Extender, Locket 101 Wire Gauge 68
Riveters Spark Plug Cleaner 79 Wire Marker 100
Blind 27 Spark Plug Cleaner & Tester 1, 75, 79 Wire Twister 58, 59
Cherry® 3 Spark Plug Gapper 75, 80 Wrench
Gauge Built® 24 Spark Plug Gap Gauge 76, 80 Air Impact 106
Huck® 6, 26 Spark Plug Inspection Magnifier 76, 79 Cessna Oil Nut 84
Riveters Tape 43 Spark Plug Lead Wrench 75 Cylinder Base 85
Riveting Equipment 18, 19, 20, 21 Spark Plug Socket 76, 80 Ratchet 104
Riveting Kits 7, 8, 9, 10, 11 Spark Plug Thread Chaser 76, 80 Torque 104
Rivets Spark Plug Thread Lubricant 75
Brake Relining 89 Spark Plug Tray 76 X
Cherrymax® 13 Spark Plug Vibrator Cleaner 75, 79
Solid AN 14 X-Out™ Screw Remover 95
Spotcheck, Magnaflux® 72
Rivet Cutter 14 Spray Wand Cleaner 97 Z
Rivet Guns 16, 17 Strap Duplicators 37
Rivet Puller 26, 27 Zyglo™ Test Kit, Magnaflux 72
Strut Coupler 90
Rivet Removal Kit 14 Strut Pump 90
Rivet Sets 18, 19 Strut Servicing Kit 90
Rivet Set Extension 19 Swagers 61, 62
Rivet Shaver 29, 30 Swaging Machines 61
Rivet Spacing Tool 20 Switch, Push To Talk 92
Rivet Squeezer 22, 23
Rivet Squeezer Sets 23 T
Rivet Squeezer Yokes 22
Rivet Trimmer 13 Tachometer, Digital Propeller 73
Rotary Machine, Sheet Metal 57 Tape Measure 68
Router Bits, Aircraft Tapered 41 Tap & Die Sets 105
Rules, Measuring 67 Telescoping Gauges 66
112