Professional Documents
Culture Documents
SM7352PC: Ÿ Constant Current Accuracy Is Less Than 5%
SM7352PC: Ÿ Constant Current Accuracy Is Less Than 5%
SM7352PC High Power Factor LED Constant Current Drive Control Switch QTZBISV1.0
SM7352PC
Features Overview
ÿ Wide input voltage range 85Vac~265Vac SM7352PC is a high precision, high efficiency, high power factor step-down LED constant current
ÿ Constant current accuracy is less than ± 5% Drive control switch. Works in critical conduction mode, in the 85Vac~265Vac input voltage range
ÿ Power factor PF greater than 0.9 Within the range, the constant current accuracy is less than ± 5%, and the PF value is greater than 0.9.
ÿ Efficiency greater than 90% SM7352PC is mainly suitable for high-brightness BUCK LED driver, which can achieve constant output
ÿ Support no-input electrolytic capacitor solution out current. Fewer peripheral devices, low cost of the solution, with output open, short circuit protection, over temperature protection
ÿ Support low-cost non-isolated buck driver It can pass reliability tests such as EFT and lightning surge.
Program
Pin Diagram
2 VDD
ÿ Built-in power MOS transistor
3 FB DRAIN 6
ÿ Package: SOP8-7
SM7352PC
4 CS DRAIN 5
SOP8-7
2 1 8
AC
led
burden
load
-1-
Machine Translated by Google
SM7352PC High Power Factor LED Constant Current Drive Control Switch QTZBISV1.0
VDD DRAIN
FB Overvoltage protection
start up
circuit
zero crossing
detect
COMP GND
Pin Description
FB 3 Feedback port
Ordering Information
Packing
Order model Package form Reel size
Tube Tape
-2-
Machine Translated by Google
SM7352PC High Power Factor LED Constant Current Drive Control Switch QTZBISV1.0
Limit parameters
VFB -0.3ÿ7 V
FB input voltage
VCS -0.3ÿ7 V
CS input voltage
VCOMP -0.3ÿ7 V
Error Amplifier Compensation Port
TJ -40~150 °C
Operating Junction Temperature Range
TSTG -55~150 °C
storage temperature
VESD >2 KV
HBM Human Body Discharge Mode
Note: The maximum peak temperature of surface mount product soldering cannot exceed 260°C. The temperature curve is set by the factory according to the J-STD-020 standard, referring to the actual situation of the factory and the recommendations of the solder paste manufacturer.
scope
symbol illustrate condition unit
minimum typical maximum
UVLOH
VDD turn-on voltage - - 14.8 - V
UVLOL
VDD undervoltage protection threshold
- - 7.9 - V
TLEB
blanking time - - 500 - nS
TOFFmax
maximum closing time VDD=18V CS=0V FB=0V - 200 - uS
Rdson
MOSFET on-resistance Io=1.0A - 6.5 - ohms
TREG
Superheat regulation temperature
- - 140 - °C
-3-
Machine Translated by Google
SM7352PC High Power Factor LED Constant Current Drive Control Switch QTZBISV1.0
functional statement
SM7352PC is a high precision, high efficiency, high power factor step-down LED constant current drive control switch. operates in critical conduction mode, the
Within the input voltage range of 85Vac~265Vac, the constant current accuracy is less than ± 5%, and the PF value is greater than 0.9.
SM7352PC is mainly suitable for high-brightness BUCK LED driver, which can achieve constant output current. Fewer peripheral devices, low cost of the solution, with output
Open, short circuit protection, over temperature protection characteristics, can pass EFT, lightning surge and other reliability tests.
ÿ Start
After the system is powered on, the sine half-wave voltage charges the capacitor of the VDD pin through the start-up resistor. When the VDD voltage rises to the start-up threshold voltage, the
The internal control circuit of the chip starts to work and starts to output pulse signals. The COMP port voltage gradually rises from 0V, and the system runs at the minimum on-time
Start to work, as the COMP voltage rises, the on-time gradually increases, and finally stabilizes, so as to realize the soft start of the output LED current, effectively preventing the
Output current overshoot. When the output voltage is established, the VDD voltage is powered by the output voltage through the diode.
The chip samples the inductor current and uses the internal error amplifier to form a closed-loop feedback network, so as to obtain high constant current accuracy and high load regulation rate.
The CS voltage and reference voltage are error-amplified by the transconductance amplifier and integrated by the external COMP capacitor. COMP terminal voltage controls external power
VEA REF
_
I OUT ÿ
RCS
Where, VEA_REF is the internal reference voltage; RCS is the value of the current sampling resistor. ÿ Switch loop
control
SM7352PC controls the turn-off of the power MOSFET through the conduction control module, and controls the turn-on of the MOSFET through the FB voltage zero-crossing detection module.
When the power MOSFET is turned on, the current detection resistor CS will inevitably generate high or low spikes. To avoid these sharp
The peak signal causes the controller to malfunction, and the chip has built-in leading edge blanking time at the moment of opening. During this leading edge blanking time, the GATE output driver also
ÿ FB feedback control
VFB_OVP, the ratio of the upper and lower voltage dividing resistors of FB is set according to the following formula
The FB feedback control is used to detect the output overvoltage protection (OVP), and the internal reference is set to
set:
R V
FBL ÿ
FB OVP
_
RR ÿ V
FBL FBH OVP
where RFBL is the lower voltage divider resistor of the feedback network RFBH is the upper voltage divider resistor of the feedback network
SM7352PC High Power Factor LED Constant Current Drive Control Switch QTZBISV1.0
output straight
2 1 8
SM7352PC
DRAIN
DRAIN CS FB
5 6 3 4
AC
led
burden
load
Disadvantage: When making a full voltage system, the system high and low voltage input VDD voltage difference is large.
Output ÿ-type
2 1 8
SM7352PC
DRAIN
DRAIN CS FB
5 6 3 4
AC
led
burden
load
Disadvantage: A 1206 chip capacitor is added to the cost (the reference capacitance value is 10nF).
Advantages: When making a full voltage system, the system high and low voltage input VDD voltage difference is small.
2 1 8
output assist
surge element GNDCOMP
VDD
Winding supply
SM7352PC
DRAIN
DRAIN CS FB
5 6 3 4
AC
led
burden
load
Advantages: When making a full voltage system, the system high and low voltage input VDD voltage difference is small (the auxiliary winding is designed to be 20V).
Power supply Output direct power supply Output ÿ-type filter power supply Auxiliary winding power supply
www.chinaasic.com Note: Please refer to Floor, Guowei R&D Building, No. 015, Gaoxin South 1st Road, South District, Nanshan District, Shenzhen
SM7352PC High Power Factor LED Constant Current Drive Control Switch QTZBISV1.0
1. The main loop of the system should preferably not surround the feedback loop. 2. The DRAIN pin of the chip is a heat dissipation pin, which needs to be covered with copper and exposed copper to dissipate heat.
Advantage: The system is less susceptible to interference from the main loop. Advantages: The chip has good heat dissipation and low temperature.
Leave
3. Add solder resist layer to capacitors, resistors and IC pins to increase the spacing between high and low voltage. 4. A safe distance of more than 2.5mm should be maintained between the AC and DC sides. DC side high
Advantages: Prevents parasitic impedance effects caused by flux or moisture during production Keep a safety distance of more than 1.5mm between low voltages. If the safety distance is not enough, you need to
ÿ
ÿ
5. The ground of the feedback components around the IC should be close to the ground of the IC 6. The main loop current in the figure goes through the CS resistor and goes to the IC ground along the red dotted line.
Advantages: Avoid the feedback ground wire is too long, the ground of the feedback device and the ground of the IC are generated. Because there is no large current passing between ground wires ÿ and ÿ, and there is a large current passing through the PCB from ÿ to ÿ
There is a potential difference between them, which causes system interference and inaccurate detection. The copper foil trace produces a voltage difference, so there is a potential difference between ÿ and ÿ, resulting in the CS voltage
www.chinaasic.com Note: Please refer to Floor, Guowei R&D Building, No. 015, Gaoxin South 1st Road, South District, Nanshan District, Shenzhen
SM7352PC High Power Factor LED Constant Current Drive Control Switch QTZBISV1.0
Schematic
R6 D2
2 1 8
R1
GNDCOMP
VDD C1 E1
surge element
R9
DRAIN SM7352PC R4 R3
L F1 D3 DRAIN CS FB
D6 R2
CX1
5 6 3 4
R7 L1
AC
D5 LED+
RV1
N
D4 E2 R5
C2
R8 D1
led
Bill of Materials
Inductance parameters
10 1
Incoming line
bottom view
N1
9 2
6 5
Production
SM7352PC High Power Factor LED Constant Current Drive Control Switch QTZBISV1.0
Package form
SOP8-7