Professional Documents
Culture Documents
Ac310 Manual v1.0
Ac310 Manual v1.0
warranty). If the product you received is damaged, please contact the company or the shipping company immediately. After confirming that the
1 Overview received product is intact, please confirm that the received inverter model is consistent with the product you ordered.
Inverter nameplate and model description
1 2
AC310 Series Frequency Inverter Manual AC310 Series Frequency Inverter Manual
3 4
AC310 Series Frequency Inverter Manual AC310 Series Frequency Inverter Manual
Model
Overall dimension(mm) Installation dimension(mm) Apertur Inverter dimensions (iron shell)
W H H1 D D1 W1 W2 H2 A B e
AC310-S2-R75G-B
76 200 192 155 149 65 65 193 5.5 4 3-M4
AC310-S2-1R5G-B
AC310-S2-2R2G-B
100 242 231 155 149 84 86.5 231.5 8 5.5 3-M4
AC310-S2-004G-B
AC310-T3-R75G/1R5P-B
AC310-T3-2R2G-B
AC310-T3-004G/5R5P-B
100 242 231 155 149 84 86.5 231.5 8 5.5 3-M4
AC310-T3-5R5G/7R5P-B
AC310-T3-7R5G/011P-B
116 320 307.5 175 169 98 100 307.5 9 6 3-M5
AC310-T3-011G/015P-B
AC310-T3-045G/055P
AC310-T3-075G/090P
AC310-T3-090G/110P
270 638 580 350 195 615 4-M8
AC310-T3-110G/132P
AC310-T3-132G/160P-L
350 738 680 405 220 715 4-M8
AC310-T3-160G/185P-L
AC310-T3-185G/200P-L
AC310-T3-250G/280P-L
370 1140 1050 545 200 1110 4-M16
AC310-T3-280G/315P-L
AC310-T3-015G/018P-B
AC310-T3-018G/022P-B 142 383 372 225 219 125 100 372 6 4-M5
AC310-T3-022G/030P-B
AC310-T3-030G/037P
172 430 / 225 219 150 150 416.5 7.5 4-M5
AC310-T3-037G/045P
5 6
AC310 Series Frequency Inverter Manual AC310 Series Frequency Inverter Manual
R External DCDC
External External Reactor
Rector
150mm以上
Brake
Resistor Short Note1
通风方向
Ventilation direction
Piece
MCCB Contactor Intput Reactor
Input Rector Output
Output Reactor
Rector
AC POWER INPUT
(-) (+) (+) PB (+) P1
R U U
R
V M
S S V ~
W
T T W
Shielded cable or armoured cable
VFD
(the end close to VFD grounding)
Note2 +24V E (The grounding resistance
PLC is less than 10 ohms)
Note:Function description in brackets is COM
150mm以上
factory default AC220V MAX Output Of Contact:
Passive contact
TA 3A/240VAC
通风方向
Ventilation direction (Forward) X1 Coil 5A/30VDC
output
左右空间不设限 TB
Left and right space is not limited (Reverse) X2
Open collector(OC)
(Free STOP) X5 Shielded cable
Coil
Y (the end close
state output
PUL
to VFD grounding)
COM
COM
A+ Note:
External keyboard shape and opening size Note: LCD keyboard is fully compatible with LED keyboard size and opening size。 RS485 Differential 120Ω 1.MAX Output of +24V Port:DC24V/100mA
Communication 2.Max Output of Y Port :DC24V/50mA
B-
20
0
Analog monitoring
Analog Voltage/Current quantity input
signal output
AI1 + -
Analog Voltage/Current quantity input Shielded cable (the
Self-tapping
使 用 自攻 钉 ST3*6 Screw AI2 A0
GND end close to VFD
grounding)
GND
17.5 Note: 1.MAX Output of +10V port :50mA
Note:When output type of AO port as
2.Inner resistance of AI1/AI2 Port frequency and Voltage,
100
17.5
3.5 Maximum Output:2mA
Legend: 1.Symbol represent main circuit terminals;
49.4 2.Symbol represent control circuit terminals.
37.8
Note: 1. When installing the DC reactor, be sure to remove the shorting tab between the P1 and (+) terminals.
键盘 安 装开
Keyboard 孔 尺寸
Installation Size 2. The terminal (X1~X5/PUL) can select the NPN or PNP transistor signal as the input, and the bias voltage can select the internal power
35.6 49.4
supply (+24V terminal) or external power supply (PLC terminal) of the inverter.
119
119*70mm; program.
Passive connector output; can set the action-object by
TA/TB/TC 3A/240VAC; 5A/30VDC
program.
1.8
7 8
AC310 Series Frequency Inverter Manual AC310 Series Frequency Inverter Manual
●Key function
9 10
AC310 Series Frequency Inverter Manual AC310 Series Frequency Inverter Manual
11 12
AC310 Series Frequency Inverter Manual AC310 Series Frequency Inverter Manual
15 16
AC310 Series Frequency Inverter Manual AC310 Series Frequency Inverter Manual
17 18
AC310 Series Frequency Inverter Manual AC310 Series Frequency Inverter Manual
F03.12 Current loop Q-axis V/F SVC FVC PMVF PMSVC PMFVC 1.00
RUN F03.4x-F03.5x: Torque Controlling
(0x030C) proportional gain Set the current loop Q-axis proportional gain (0.001 ~ 4.000)
F03.13 Current loop Q-axis V/F SVC FVC PMVF PMSVC PMFVC 1.00 Parameter Factory default Adjustable
RUN Name Content
(0x030D) integral gain Set the current loop Q-axis integral gain (0.001 ~ 4.000) (Address) (range) properly
V/F SVC FVC PMVF PMSVC PMFVC
F03.15 Electric state torque V/F SVC FVC PMVF PMSVC PMFVC 250.0% F03.40 Torque control 0
RUN 0:speed control mode torque limited 1:torque control mode RUN
(0x030E) limit Set the motor state torque limit. (0.0~400.0%) (0x0328) selection (0 ~ 1)
speed limited
F03.16 Power generation V/F SVC FVC PMVF PMSVC PMFVC 250.0% V/F SVC FVC PMVF PMSVC PMFVC
RUN
(0x030F) torque limit Set the power generation torque limit (0.0~400.0%) Unit: Channel A Ten: Channel B
0: Keyboard number given 1: Reserved
F03.17 Regenerative torque V/F SVC FVC PMVF PMSVC PMFVC 0.0%
RUN 2: Current/voltage analog AI1 given
(0x0312) limit at low speed Set the regenerative torque limit at low speed (0.0~400.0%)
3: Current/voltage analog AI2 given
Torque limit action F03.41 Torque command 4: Reserved 5: PUL 0000
F03.18 V/F SVC FVC PMVF PMSVC PMFVC 6.00s RUN
frequency amplitude at RUN (0x0329) given 6: RS485 communication reference 7: Option card (0000~0577)
(0x0313) Set the torque limit action frequency amplitude at low speed (0.00~30.00s)
low speed Hundreds: command given mode
0: channel A 1: channel B
F03.2x:Torque Optimization Controlling 2: Channel A + Channel B 3: Channel A - Channel B
4: Minimum value of channel A and channel B
Parameter Factory default Adjustable 5: Maximum value of channel A and channel B
Name Content
(Address) (range) properly F03.42 Torque keyboard digital V/F SVC FVC PMVF PMSVC PMFVC 0.0%
RUN
Synchronous motor V/F SVC FVC PMVF PMSVC PMFVC (0x032A) setting Set the torque command given (0.0 ~ 100.0%)
F03.20 20.0% F03.43 V/F SVC FVC PMVF PMSVC PMFVC 0.00%
(0x0314) low frequency pull-in The PM motor open loop control is effective, and the larger the RUN Torque input lower limit RUN
(0.0 ~ 50.0%) (0x032B) Set the torque input lower limit. (0.0 ~ 100.00%)
current pull-in current is, the larger the torque output is.。
Synchronous motor V/F SVC FVC PMVF PMSVC PMFVC F03.44 Lower limit V/F SVC FVC PMVF PMSVC PMFVC 0.0%
F03.21 10.0% RUN
high frequency pull-in The PM motor open loop control is effective, and the larger the RUN (0x032C) corresponding setting Set the lower limit corresponding value. (-200.0~200.0%)
(0x0315) (0.0 ~ 50.0%) F03.45 V/F SVC FVC PMVF PMSVC PMFVC 100.0%
current pull-in current is, the larger the torque output is. Torque input upper limit RUN
Synchronous motor V/F SVC FVC PMVF PMSVC PMFVC (0x032D) Set the upper limit of the torque input. (0.0~100.0%)
F03.22 10.0%
pull-in current The set value 100.0% corresponds to F01.10 [maximum RUN F03.46 Upper limit V/F SVC FVC PMVF PMSVC PMFVC 100.0%
(0x0316) (0.0 ~ 100.0%) RUN
frequency frequency]. (0x032E) corresponding setting Set the upper limit corresponding value. (-200.0~200.0%)
F03.47 V/F SVC FVC PMVF PMSVC PMFVC 0.100s
F03.23 Asynchronous motor V/F SVC FVC PMVF PMSVC PMFVC 100.0% Torque filtering time RUN
RUN (0x032F) Set the torque limit action frequency range at low speed. (0.000~6.000s)
(0x0317) slip compensation Set the asynchronous motor speed slip compensation. (0.0 ~ 250.0%)
F03.52 V/F SVC FVC PMVF PMSVC PMFVC 150.0%
Output torque limit RUN
(0x0334) Set the upper limit of the output torque. (0.0 ~ 200.0%)
F03.24 Starting torque initial V/F SVC FVC PMVF PMSVC PMFVC 0.0% F03.53 Output torque lower V/F SVC FVC PMVF PMSVC PMFVC 0.0%
RUN RUN
(0x0318) value Set the initial value of the starting torque (0.0 ~ 250.0%) (0x0335) limit Set the lower limit of the output torque. (0.0 ~ 200.0%)
V/F SVC FVC PMVF PMSVC PMFVC
F03.3x:Magnetic Flux Optimization 0: function code F03.56 setting; 1: reserved
F03.54 Torque control forward 2: AI1×F03.56; 3: AI2×F03.56; 0
RUN
Parameter Factory default Adjustable (0x0336) speed limit selection 4: Reserved 5: PUL × F03.56; (0 ~ 7)
Name Content
(Address) (range) properly 6: RS485 communication given × F03.56 7: Option card ×
F03.57
F03.30 Weak magnetic feed V/F SVC FVC PMVF PMSVC PMFVC 10.0% V/F SVC FVC PMVF PMSVC PMFVC
RUN
(0x031E) forward coefficient Set the weak magnetic feed forward coefficient (0.0 ~500.0%) 0: Function code F03.57 setting; 1 reserved
F03.31 Weak magnetic control V/F SVC FVC PMVF PMSVC PMFVC 10.0% F03.55 Torque control reverse 2: AI1×F03.57; 3: AI2×F03.57; 0
RUN RUN
(0x031F) gain Set the weak magnetic control gain (0.0 ~ 500.0%) (0x0337) speed limit selection 4: Reserved 5: PUL × F03.57; (0 ~ 7)
F03.32 Weak magnetic current V/F SVC FVC PMVF PMSVC PMFVC 60.0% 6: RS485 communication given × F03.57 7: Option card ×
RUN F03.57
(0x0320) upper limit Set the weak magnetic current upper limit (0.0 ~ 250.0%)
F03.33 Weak magnetic V/F SVC FVC PMVF PMSVC PMFVC 97.0% Torque control forward
RUN F03.56 V/F SVC FVC PMVF PMSVC PMFVC 100.0%
(0x0321) voltage coefficient Set the weak magnetic voltage coefficient (0.0 ~ 120.0%) speed maximum RUN
(0x0338) Set the torque control forward maximum speed limit. (0.0~100.0%)
speed limit
F03.34 V/F SVC FVC PMVF PMSVC PMFVC 250.0%
Output power limit RUN F03.57 Torque control reverse V/F SVC FVC PMVF PMSVC PMFVC 100.0%
(0x0322) Set the output power limit (0.0 ~ 400.0%) RUN
(0x0339) maximum speed limit Set the torque control reverse maximum speed limit. (0.0~100.0%)
F03.35 Overexcitation braking V/F SVC FVC PMVF PMSVC PMFVC 100.0%
RUN
(0x0323) gain Set the overexcitation braking gain (0.0 ~ 500.0%)
F03.6x: PM High Frequency Injection
F03.36 Overexcitation braking V/F SVC FVC PMVF PMSVC PMFVC 10.0%
RUN
(0x0324) limit Set the overexcitation braking limit (0.0 ~ 250.0%) Parameter Factory default Adjustable
F03.37 Energy efficient V/F SVC FVC PMVF PMSVC PMFVC 0 Name Content
RUN (Address) (range) properly
(0x0325) operation 0:Off 1:On (0 ~ 1)
V/F SVC FVC PMVF PMSVC PMFVC
Energy-saving F03.60 High frequency Valid under PM motor open loop control 0
F03.38 V/F SVC FVC PMVF PMSVC PMFVC 50.0% STOP
operation excitation RUN (0x033C) injection selection 0: Disabled 1~5: Enable. The larger the value, the higher the (0 ~ 5)
(0x0326) Set the Energy-saving operation excitation lower limit (0.0 ~ 80.0%)
lower limit frequency injected.
Energy-saving
F03.39 V/F SVC FVC PMVF PMSVC PMFVC 0.010s V/F SVC FVC PMVF PMSVC PMFVC
operating filter RUN F03.61 High frequency 10.0%
(0x0327) Set the Energy-saving operating filter coefficient (0.000 ~ 6.000s) Injection voltage amplitude, related to rated voltage, self-learning RUN
coefficient (0x033D) injection voltage (0.0 ~ 100.0%)
results, generally do not need to be modified.
High frequency V/F SVC FVC PMVF PMSVC PMFVC
F03.62 10.0%
injection cutoff The frequency range of the high frequency injection is relatively RUN
(0x033E) (0.0 ~ 100.0%)
frequency high, and the high frequency injection is effective when the motor
19 20
AC310 Series Frequency Inverter Manual AC310 Series Frequency Inverter Manual
speed is less than this value. F04.12 V/F SVC FVC PMVF PMSVC PMFVC 28.0%
Self-setting voltage V2 STOP
(0x040C) Self-setting voltage V2 (0.0 ~ 100.0%)
F04.13 V/F SVC FVC PMVF PMSVC PMFVC 10.0Hz
V/F SVC FVC PMVF PMSVC PMFVC Self-set frequency F2 STOP
F03.70 Position compensation 0.0 (0x040D) Self-set frequency F2 (0.00~ Max)
Position compensation control under speed control for zero RUN F04.14 V/F SVC FVC PMVF PMSVC PMFVC 55.0%
(0x0346) control (0 ~ 250.0) Self-setting voltage V3 STOP
servo or increased system rigidity (0x040E) Self-setting voltage V3 (0.0 ~ 100.0%)
F03.71 V/F SVC FVC PMVF PMSVC PMFVC 1.0
Compensation gain RUN F04.15 V/F SVC FVC PMVF PMSVC PMFVC 25.00Hz
(0x0347) Set compensation gain (0.0 ~ 100.0) Self-set frequency F3 STOP
(0x040F) Self-set frequency F3 (0.00~ Max)
F03.72 Compensation V/F SVC FVC PMVF PMSVC PMFVC 0.0%
STOP F04.16 V/F SVC FVC PMVF PMSVC PMFVC 78.0%
(0x0348) amplitude limit Set the compensation amplitude limit value. (0.0 ~ 100.0%) Self-setting voltage V4 STOP
(0x0410) Self-setting voltage V4 (0.0 ~ 900.0%)
F03.73 V/F SVC FVC PMVF PMSVC PMFVC 10.0%
Compensation range STOP F04.17 V/F SVC FVC PMVF PMSVC PMFVC 37.5Hz
(0x0349) Set the compensation range. (0.0 ~ 100.0%) Self-set frequency F4 STOP
(0x0411) Self-set frequency F4 (0.00~ Max)
F03.80 Synchronous motor V/F SVC FVC PMVF PMSVC PMFVC 100.0%
RUN F04.18 V/F SVC FVC PMVF PMSVC PMFVC 100.0%s
(0x0350) MTPA gain Set the synchronous motor MTPA gain. (0.0 ~ 400.0%) Self-setting voltage V5 STOP
(0x0412) Self-setting voltage V5 (0.0~100.0%)
F03.81 Synchronous motor V/F SVC FVC PMVF PMSVC PMFV 1.0ms F04.19 V/F SVC FVC PMVF PMSVC PMFVC 50.0Hz
RUN Self-set frequency F5 STOP
(0x0351) MTPA filter time Set the MTPA filter time of the synchronous motor. (0.0 ~ 100.0ms) (0x0413) Self-set frequency F5 (0.00~ Max)
F04.2x:Reserved
4.7 F04 :V/F Controlling
F04.3x:V/F Energy Saving Controlling
F04.0x:V/F Controlling Parameter
Name Content
Factory default Adjustable
(Address) (range) properly
Parameter Factory default Adjustable F04.30 Automatic energy V/F SVC FVC PMVF PMSVC PMFVC 0
Name Content STOP
(Address) (range) properly (0x041E) saving control 0:Off 1:On (0 ~ 1)
V/F SVC FVC PMVF PMSVC PMFVC
Used to select the type of V/F curve to meet different load Energy saving
F04.31 V/F SVC FVC PMVF PMSVC PMFVC 15.0Hz
F04.00 Linear VF curve characteristics. 0 step-down frequency STOP
STOP (0x041F) Set the lower limit of the energy saving step-down frequency. (0.0~50.0Hz)
(0x0400) selection 0: straight VF curve; 1-9: respectively, a power curve of 1.1-1.9 (0 ~ 11) lower limit
VF; Energy-saving
10: square VF curve; 11: customize VF curve; F04.32 V/F SVC FVC PMVF PMSVC PMFVC 50.0%
step-down voltage STOP
(0x0420) Set the lower limit of the energy-saving step-down voltage. (20.0~100.0%)
V/F SVC FVC PMVF PMSVC PMFVC lower limit
F04.01 0.0%
Torque boost 0.0%: automatic torque boost; 0.1 to 30.0%: manual torque RUN F04.33 Energy-saving V/F SVC FVC PMVF PMSVC PMFVC 0.010V/MS (0.000~
(0x0401) (0.0 ~ 30.0%) RUN
boost (0x0421) step-down voltage Set the energy-saving step-down voltage regulation rate. 0.200 V/MS)
V/F SVC FVC PMVF PMSVC PMFVC F04.34 V/F SVC FVC PMVF PMSVC PMFVC 0.20V/MS (0.00~
F04.02 Torque boost cutoff Set the effective range of the torque boost function. When the 100.0% Adjustment rate RUN
RUN (0x0422) Set the energy saving voltage recovery rate. 2.00 V/MS)
(0x0402) frequency output frequency exceeds this value, the torque boost function is (0.0 ~ 100.0%)
cut off.
F04.03
(0x0403)
Slip compensation gain
V/F SVC FVC PMVF PMSVC PMFVC
Set the slip compensation gain.
0.0%
(0.0 ~ 200.0%)
RUN 4.8 F05:Input Terminal
F04.04 V/F SVC FVC PMVF PMSVC PMFVC 100.0%
(0x0404)
Slip compensation limit
Set the slip compensation limit value. (0.0 ~ 300.0%)
RUN F05.0x:Digital Input Terminal Function
V/F SVC FVC PMVF PMSVC PMFVC Parameter Factory default Adjustable
F04.05 Slip compensation filter The slip compensation function needs to correctly input the 0.200 Name Content
RUN (Address) (range) properly
(0x0405) time motor nameplate parameters and learn the parameters to (0.000 ~ 6.000)
achieve the best results. F05.00 Terminal X1 function V/F SVC FVC PMVF PMSVC PMFVC 1
selection STOP
V/F SVC FVC PMVF PMSVC PMFVC (0x0500) See the function of the terminal for details. (0 ~ 95)
F04.06 Oscillation suppression By adjusting this value, low frequency resonance can be 100.0% Terminal X2 function
RUN F05.01 V/F SVC FVC PMVF PMSVC PMFVC 2
(0x0406) gain suppressed, but not too large, otherwise it will cause additional (0.0 ~ 900.0%) selection STOP
(0x0501) See the function of the terminal for details. (0 ~ 95)
stability problems.。
F05.02 Terminal X3 function V/F SVC FVC PMVF PMSVC PMFVC 4
F04.07 Oscillation suppression V/F SVC FVC PMVF PMSVC PMFVC 1.0 STOP
RUN (0x0502) selection See the function of the terminal for details. (0 ~ 95)
(0x0407) filter time Set the oscillation suppression filter time. (0.0 ~ 100.0s) Terminal X4 function
F05.03 V/F SVC FVC PMVF PMSVC PMFVC 5
selection STOP
F04.08 Output voltage V/F SVC FVC PMVF PMSVC PMFVC 100.0%s (0x0503) See the function of the terminal for details. (0 ~ 95)
STOP
(0x0408) percentage Set the output voltage percentage (25.0~120.0%) F05.04 Terminal X5 function V/F SVC FVC PMVF PMSVC PMFVC 6
selection STOP
(0x0504) See the function of the terminal for details. (0 ~ 95)
F04.1x: Custom V/F Curve F05.05 Terminal X6 function V/F SVC FVC PMVF PMSVC PMFVC 0
selection STOP
(0x0505) See the function of the terminal for details. (0 ~ 95)
Parameter Factory default Adjustable Terminal X7 function
Name Content F05.06 V/F SVC FVC PMVF PMSVC PMFVC 0
(Address) (range) properly selection STOP
(0x0506) See the function of the terminal for details. (0 ~ 95)
F04.10 V/F SVC FVC PMVF PMSVC PMFVC 3.0% Terminal X8 function
Self-setting voltage V1 STOP F05.07 V/F SVC FVC PMVF PMSVC PMFVC 0
(0x040A) Self-setting voltage V1 (0.0 ~ 100.0%) selection STOP
(0x0507) See the function of the terminal for details. (0 ~ 95)
F04.11 V/F SVC FVC PMVF PMSVC PMFVC 1.00Hz Terminal X9 function
Self-set frequency F1 STOP F05.08 V/F SVC FVC PMVF PMSVC PMFVC 0
(0x040B) Self-set frequency F1 (0.00~Max) selection STOP
(0x0508) See the function of the terminal for details. (0 ~ 95)
21 22
AC310 Series Frequency Inverter Manual AC310 Series Frequency Inverter Manual
23 24
AC310 Series Frequency Inverter Manual AC310 Series Frequency Inverter Manual
25 26
AC310 Series Frequency Inverter Manual AC310 Series Frequency Inverter Manual
F06.30 Relay 1 output OFF V/F SVC FVC PMVF PMSVC PMFVC 0.010s Parameter Factory default Adjustable
RUN Name Content
(0x061E) delay time Set relay 1 output OFF delay time. (0.000~60.000s) (Address) (range) properly
F06.31 Extended Y1 output V/F SVC FVC PMVF PMSVC PMFVC 0.010s F06.60 Virtual vX1 terminal V/F SVC FVC PMVF PMSVC PMFVC 0
RUN RUN
(0x061F) OFF delay time Set the extended Y1 output OFF delay time (0.000~60.000s) (0x063C) function selection See terminal X function (0 ~ 63)
F06.61
F06.32 Extended relay 2 V/F SVC FVC PMVF PMSVC PMFVC 0.010s Virtual vX2 terminal V/F SVC FVC PMVF PMSVC PMFVC 0
RUN (0x063D) RUN
(0x0620) output OFF delay time Set the extended relay 2 output OFF delay time. (0.000~60.000s) function selection See terminal X function (0 ~ 63)
RUN
F06.62 Virtual vX3 terminal V/F SVC FVC PMVF PMSVC PMFVC 0
RUN
F06.4x: Frequency Detection (0x063E) function selection See terminal X function (0 ~ 63)
F06.63 Virtual vX4 terminal V/F SVC FVC PMVF PMSVC PMFVC 0
RUN
Parameter Factory default Adjustable (0x063F) function selection See terminal X function (0 ~ 63)
Name Content
(Address) (range) properly V/F SVC FVC PMVF PMSVC PMFVC
0: Internal connection with virtual vYn 1: Link with physical terminal
2.00Hz F06.64 vX terminal valid status Xn 0000
F06.40 Frequency detection V/F SVC FVC PMVF PMSVC PMFVC RUN
(0.00~max RUN (0x0640) source 2:whether the function code setting is valid? (0000 ~ 2222)
(0x0628) value 1 Set the frequency detection value 1
frequency) Unit: Virtual vX1 Ten: Virtual vX2
1.00Hz Hundreds place: virtual vX3 thousand: virtual vX4
F06.41 Frequency detection V/F SVC FVC PMVF PMSVC PMFVC
(0.00~max RUN V/F SVC FVC PMVF PMSVC PMFVC
(0x0629) amplitude 1 Set the frequency detection amplitude 1 Virtual vX terminal
frequency) F06.65 0: invalid; 1: valid 0000
function code setting RUN
2.00Hz (0x0641) Unit: Virtual vX1 Ten: Virtual vX2 (0000 ~ 1111)
F06.42 Frequency detection V/F SVC FVC PMVF PMSVC PMFVC valid status
(0.00~max RUN Hundreds place: virtual vX3 thousand: virtual vX4
(0x062A) value 2 Set the frequency detection value 2 F06.66 Virtual vY1 output V/F SVC FVC PMVF PMSVC PMFVC 0
frequency) RUN
1.00Hz (0x0642) selection See Y terminal function for details. (0~31)
F06.43 Frequency detection V/F SVC FVC PMVF PMSVC PMFVC
(0.00~max RUN F06.67 Virtual vY2 output V/F SVC FVC PMVF PMSVC PMFVC 0
(0x062B) range 2 Set the frequency detection range 2 RUN
frequency) (0x0643) selection See Y terminal function for details. (0~31)
The given frequency 2.00Hz
F06.44 V/F SVC FVC PMVF PMSVC PMFVC F06.68 Virtual vY3 output V/F SVC FVC PMVF PMSVC PMFVC 0
reaches the detection (0.00~max RUN RUN
(0x062C) Set the given frequency to reach the detection range (0x0644) selection See Y terminal function for details. (0~31)
range frequency)
F06.5x:Monitor parameter comparator output F06.69 Virtual vY4 output V/F SVC FVC PMVF PMSVC PMFVC 0
RUN
(0x0645) selection See Y terminal function for details. (0~31)
Parameter Factory default Adjustable F06.70 vY1 output ON delay V/F SVC FVC PMVF PMSVC PMFVC 0.010s
Name Content RUN
(Address) (range) properly (0x0646) time Set vY1 output ON delay time (0.000~60.000s)
F06.71 vY2 output ON delay V/F SVC FVC PMVF PMSVC PMFVC 0.010s
RUN
(0x0647) time Set vY2 output ON delay time (0.000~60.000s)
V/F SVC FVC PMVF PMSVC PMFVC F06.72 vY3 output ON delay V/F SVC FVC PMVF PMSVC PMFVC 0.010s
F06.50 Comparator 1 monitor Units and Tens digits: Set yy value of the Cxx.yy 00~63 0001 RUN
RUN (0x0648) time Set vY3 output ON delay time (0.000~60.000s)
(0x0632) selection (0000 ~ 0763)
Hundreds and thousands: Set xx value of the Cxx.yy 00~07
F06.73 vY4 output ON delay V/F SVC FVC PMVF PMSVC PMFVC 0.010s
RUN
(0x0649) time Set vY4 output ON delay time (0.000~60.000s)
F06.51 Comparator 1 upper V/F SVC FVC PMVF PMSVC PMFVC 3000 F06.74 vY1 output OFF delay V/F SVC FVC PMVF PMSVC PMFVC 0.010s
RUN RUN
(0x0633) limit Set the upper limit of comparator 1 (0 ~ 65535) (0x064A) time Set vY1 output OFF delay time (0.000~60.000s)
F06.52 Comparator 1 lower V/F SVC FVC PMVF PMSVC PMFVC 0 F06.75 vY2 output OFF delay V/F SVC FVC PMVF PMSVC PMFVC 0.010s
RUN RUN
(0x0634) limit Set the lower limit of comparator 1 (0 ~ 65535) (0x064B) time Set vY2 output OFF delay time (0.000~60.000s)
F06.53 V/F SVC FVC PMVF PMSVC PMFVC 0 F06.76 vY3 output OFF delay V/F SVC FVC PMVF PMSVC PMFVC 0.010s
Comparator 1 bias RUN RUN
(0x0635) Set the comparator 1 offset value (0 ~ 1000) (0x064C) time Set vY3 output OFF delay time (0.000~60.000s)
V/F SVC FVC PMVF PMSVC PMFVC F06.77 vY4 output OFF delay V/F SVC FVC PMVF PMSVC PMFVC 0.010s
RUN
F06.54 Action selection when 0:Continue running(digital terminal output only); 0 (0x064D) time Set vY4 output OFF delay time (0.000~60.000s)
RUN
(0x0636) sending CP1 1:Warning and free stop;2:Warning and continue running; (0 ~ 3)
3:Forced stop
V/F SVC FVC PMVF PMSVC PMFVC
F06.55 Comparator 2 monitor Units and Tens digits: Set yy value of the Cxx.yy 00~63 0002
RUN
(0x0637) selection (0000 ~ 0763)
Hundreds and thousands: Set xx value of the Cxx.yy 00~07
F06.56 Comparator 2 upper V/F SVC FVC PMVF PMSVC PMFVC 30
RUN
(0x0638) limit Set the upper limit of comparator 2 (0 ~ 65535)
F06.57 Comparator 2 lower V/F SVC FVC PMVF PMSVC PMFVC 0
RUN
(0x0639) limit Set the lower limit of comparator 2 (0 ~ 65535)
F06.58 V/F SVC FVC PMVF PMSVC PMFVC 0
Comparator 2 bias RUN
(0x063A) Set the comparator 2 offset value (0 ~ 1000)
V/F SVC FVC PMVF PMSVC PMFVC
F06.59 Action selection when 0: Continue running (digital terminal output only) 0
RUN
(0x063B) sending CP2 1: Warning and free stop 2: Warning and continue to run 3: Forced (0 ~ 3)
stop
27 28
AC310 Series Frequency Inverter Manual AC310 Series Frequency Inverter Manual
F07.20 Braking current before V/F SVC FVC PMVF PMSVC PMFVC 60.0%
STOP
4.10 F07 :Operational Control (0x0714)
F07.21
starting
Braking time before
Set the brake current before starting
V/F SVC FVC PMVF PMSVC PMFVC
(0.0~150.0%)
0.0s
STOP
(0x0715) starting Set the brake time before starting (0.0~60.0s)
Parameter Factory default Adjustable F07.22 DC braking start V/F SVC FVC PMVF PMSVC PMFVC 1.00Hz
Name Content STOP
(Address) (range) properly (0x0716) frequency Set the DC brake start frequency (0.00~50.00Hz)
V/F SVC FVC PMVF PMSVC PMFVC V/F SVC FVC PMVF PMSVC PMFVC
F07.23 60.0%
F07.00 0: started by the start frequency 0 DC braking current Refer to rated current,because the internal limit current cannot STOP
Start mode STOP (0x0717) (0.0~150.0%)
(0x0700) 1: DC braking first starts again from the starting frequency (0 ~ 2) exceed the rated current
2: Start after the speed tracking and direction judgment F07.24 DC braking time during V/F SVC FVC PMVF PMSVC PMFVC 0.0s
STOP
V/F SVC FVC PMVF PMSVC PMFV (0x0718) stopping Set the DC braking time during stopping (0.0~60.0s)
F07.01 Start pre-excitation 0.00s
Only asynchronous machine vector control (without PG) supports STOP V/F SVC FVC PMVF PMSVC PMFVC
(0x0701) time (0.00~60.00s)
pre-excitation, other ignore Units: Search method
V/F SVC FVC PMVF PMSVC PMFVC 0.50Hz 0: Search from the maximum frequency 1: Search from the stop
F07.02
Starting frequency When the given frequency is less than this value, it does not start (0.00~upper limit STOP frequency
(0x0702) F07.25 0000
and is in standby state frequency setting) Speed tracking mode Tens:Reverse search STOP
(0x0719) (0000~1111)
V/F SVC FVC PMVF PMSVC PMFVC 0:Off 1:On
0: off 1: on
Hundreds: Search source
Unit: terminal start protection when exiting abnormal
0:Software search 1:Hardware search
Tens: Jog terminal start protection when exiting abnormal
F07.03 Start protection 0111 F07.26 V/F SVC FVC PMVF PMSVC PMFVC 0.5s
Hundreds: terminal start protection when the command channel is STOP Speed tracking speed STOP
(0x0703) selection (0000~1111) (0x071A) Set the speed of tracking speed (0.0~60.0s)
switched to the terminal
Note: When the free stop, emergency stop, and forced stop
F07.27 Speed tracking stop V/F SVC FVC PMVF PMSVC PMFVC 1.00s
commands are valid, the terminal start protection is enabled by STOP
(0x071B) delay Set speed tracking stop delay (0.0~60.0s)
default, and the protection time is reported as A.RUNx warning.
V/F SVC FVC PMVF PMSVC PMFVC F07.28 V/F SVC FVC PMVF PMSVC PMFVC 120.0%
Speed tracking current STOP
Unit: running direction (0x071C) Set speed tracking current (0.0~400.0%)
0:Direction unchanged 1:Direction reversed
F07.05 Tens:running direction selection 0000 F07.3x:Jog
Direction of rotation 0:allow Fwd and Rev commands 1:Fwd command only STOP
(0x0705) (0000~1121)
2:Rev command only Parameter Factory default Adjustable
Name Content
Hundreds:Frequency control command (Address) (range) properly
0:command is invalid 1:command is valid 5.00Hz
F07.30 Jog running frequency V/F SVC FVC PMVF PMSVC PMFVC
F07.06 Power failure restart V/F SVC FVC PMVF PMSVC PMFVC 0 (0.00~Max RUN
STOP (0x071E) setting Set jog running frequency
(0x0706) action selection 0:Invalid 1:Valid (0 ~ 1) frequency)
F07.07 Power failure restart V/F SVC FVC PMVF PMSVC PMFVC 0.50s F07.31 V/F SVC FVC PMVF PMSVC PMFVC 10.0s
STOP Jog acceleration time RUN
(0x0707) waiting time Set the power failure restart waiting time (0.00~60.00s) (0x071F) Set jog acceleration time (0.0~650.0s)
F07.32 V/F SVC FVC PMVF PMSVC PMFVC 10.0s
Jog deceleration time RUN
F07.1x:Stop Control (0x0720) Set jog deceleration time (0.0~650.0s)
F07.33 V/F SVC FVC PMVF PMSVC PMFVC 0
Jog S curve selection RUN
Parameter Factory default Adjustable (0x0721) 0:Invalid 1:Valid (0~1)
Name Content
(Address) (range) properly V/F SVC FVC PMVF PMSVC PMFVC
F07.34 Jog stop mode 0
F07.10 V/F SVC FVC PMVF PMSVC PMFVC 0 Set stop mode STOP
Stop mode RUN (0x0722) selection (0~1)
(0x070A) 0: Deceleration stop 1: Free stop (0 ~ 1) 0: According to F7.10 setting mode 1: Deceleration only
V/F SVC FVC PMVF PMSVC PMFVC 0.50Hz
F07.11 Shutdown detection
When decelerating to stop, when the inverter output frequency is (0.00~upper limit RUN
F07.4x:Startup、Stopping Frequency Maintenance and Jump Frequency
(0x070B) frequency
less than this value, it will enter the stop state. frequency setting)
Parameter Factory default Adjustable
F07.12 Stop and restart limit V/F SVC FVC PMVF PMSVC PMFVC 0.00s Name Content
STOP (Address) (range) properly
(0x070C) time Waiting time after restarting after shutdown (0.00~60.00s)
V/F SVC FVC PMVF PMSVC PMFVC 0.50Hz
V/F SVC FVC PMVF PMSVC PMFVC F07.40 Maintain frequency at
Insufficient lower limit Startup maintenance frequency is greater than the start frequency, (0.00~Upper limit STOP
F07.15 0 : Run according to frequency command 0 (0x0728) startup
frequency action RUN less than the upper limit set frequency frequency)
(0x070F) 1 : Free running stops, enters the pause state (0~3)
selection
2 : Run at the following limited frequency 3 : Zero speed operation V/F SVC FVC PMVF PMSVC PMFVC
F07.41 Maintain frequency 0.0s
V/F SVC FVC PMVF PMSVC PMFVC The value should be higher than the start frequency, and when it is STOP
F07.16 Zero speed torque 60.0% (0x0729) time at startup (0.0~60.0s)
Set zero speed torque current, 100.0% corresponds to inverter RUN lower, according to start frequency
(0x0710) retention factor (0.0~150.0%)
rated current
0.50Hz
F07.17 Zero speed torque V/F SVC FVC PMVF PMSVC PMFVC 0.0s F07.42 Maintain frequency V/F SVC FVC PMVF PMSVC PMFVC
RUN (0.00~Upper limit STOP
(0x0711) holding time Set zero speed torque hold time (0.0~6000.0s) (0x072A) during stop Set the maintain frequency during stop
frequency)
F07.18 Positive reversal dead V/F SVC FVC PMVF PMSVC PMFVC 0.0s
STOP F07.43 Maintain frequency V/F SVC FVC PMVF PMSVC PMFVC 0.0s
(0x0712) time Fwd and Rev switching, zero frequency maintenance time (0.0~120.0s) STOP
(0x072B) time during stop Set the time of stop maintain frequency (0.0~60.0s)
F07.2x:DC Breaking and Speed Tracking F07.44 V/F SVC FVC PMVF PMSVC PMFVC
0.00Hz
Jump frequency 1 (0.00~Max RUN
(0x072C) Set the jump frequency 1
Parameter Factory default Adjustable frequency)
Name Content F07.45 Jump frequency 1 V/F SVC FVC PMVF PMSVC PMFVC
(Address) (range) properly 0.00Hz RUN
(0x072D) amplitude Set the amplitude of jump frequency 1
29 30
AC310 Series Frequency Inverter Manual AC310 Series Frequency Inverter Manual
(0.00~Max
frequency)
0.00Hz
4.12 F09:Reserved
F07.46 V/F SVC FVC PMVF PMSVC PMFVC
Jump frequency 2 (0.00~Max RUN
(0x072E) Set the jump frequency 2
frequency)
31 32
AC310 Series Frequency Inverter Manual AC310 Series Frequency Inverter Manual
33 34
AC310 Series Frequency Inverter Manual AC310 Series Frequency Inverter Manual
Parameter
Name Content
Factory default Adjustable F11.1x:Status Interface Cyclic Monitoring
(Address) (range) properly
V/F SVC FVC PMVF PMSVC PMFVC Parameter Factory default Adjustable
F10.50 Set the allowable times of fault self-recovery. 0 Name Content
Fault self-recovery STOP (Address) (range) properly
(0x0A32) Note: the value of 0 indicate the function is turn off otherwise the (0 ~10)
function is enable V/F SVC FVC PMVF PMSVC PMFVC
Unit: left shift key to adjust the first line of monitoring
F10.51 Fault self-recovery V/F SVC FVC PMVF PMSVC PMFVC 1.0s Status interface left 0: Invalid 1: Valid
STOP F11.10 0011
(0x0A33) interval Set the waiting time from fault to reset (0 ~100.0) shift, right shift key Tens: right shift key to adjust the second line of monitoring STOP
(0x0B0A) (0000 ~ 0011)
V/F SVC FVC PMVF PMSVC PMFVC function selection 0: Invalid 1: Valid
F10.52 Number of fault When the left/right shift key is invalid, the monitor display value is
This value indicates the number of self-recovery that have been 0 READ
(0x0A34) recovered displayed as parameter 1 after power-on.
performed. This parameter is a read-only parameter.
V/F SVC FVC PMVF PMSVC PMFVC
The first line of the Ten digits: yy setting in monitoring parameter number Cxx.yy
4.14 F11:Operator Parameter F11.11
keyboard shows the 00~63 0000
RUN
(0x0B0B) (0000 ~ 0763)
parameter 1 Hundreds of thousands: monitoring parameter number Cxx.yy xx
setting 00~07
F11.0x:Button Operation The first line of the
F11.12 V/F SVC FVC PMVF PMSVC PMFVC 0001
keyboard shows the RUN
Parameter Factory default Adjustable (0x0B0C) Ditto (0000 ~ 0763)
Name Content parameter 2
(Address) (range) properly
The first line of the
V/F SVC FVC PMVF PMSVC PMFVC F11.13 V/F SVC FVC PMVF PMSVC PMFVC 0002
keyboard shows the RUN
F11.00 0: No lock 1: Keyboard function parameter modification lock 0 (0x0B0D) Ditto (0000 ~ 0763)
Key lock selection RUN parameter 3
(0x0B00) 2: Function parameters and non-start and stop button lock 3: (0 ~ 3) The first line of the
function parameters and button full lock F11.14 V/F SVC FVC PMVF PMSVC PMFVC 0011
keyboard shows the RUN
(0x0B0E) Ditto (0000 ~ 0763)
F11.01 V/F SVC FVC PMVF PMSVC PMFVC 0 parameter 4
Key lock password RUN
(0x0B01) Set the key lock password (0 ~ 65535) The second line of the
F11.15 V/F SVC FVC PMVF PMSVC PMFVC 0002
keyboard shows the RUN
V/F SVC FVC PMVF PMSVC PMFVC (0x0B0F) Ditto (0000 ~ 0763)
parameter 1
0: Invalid 1: Reverse run key
2: Forward jog run key 3: Reverse jog run key The second line of the
F11.16 V/F SVC FVC PMVF PMSVC PMFVC 0004
4: Keyboard command channel and terminal naming channel keyboard shows the RUN
(0x0B10) Ditto (0000 ~ 0763)
Keyboard switch parameter 2
F11.02 0
multi-function key 5: Keyboard command channel and communication naming STOP
(0x0B02) (0 ~ 7) The second line of the
selection channel switch F11.17 V/F SVC FVC PMVF PMSVC PMFVC 0010
6: Terminal command channel and communication naming channel keyboard shows the RUN
(0x0B11) Ditto (0000 ~ 0763)
switch parameter 3
7: keyboard, terminal, communication command channel cycle The second line of the
switching F11.18 V/F SVC FVC PMVF PMSVC PMFVC 0012
keyboard shows the RUN
(0x0B12) Ditto (0000 ~ 0763)
V/F SVC FVC PMVF PMSVC PMFVC parameter 4
F11.03 Keyboard STOP 0: Non-keyboard control mode is invalid 0
STOP
(0x0B03) button settings 1: Non-keyboard control mode stops according to stop mode (0 ~ 2)
2: Non-keyboard control mode stops in free mode
V/F SVC FVC PMVF PMSVC PMFVC
Status interface up and Unit keyboard up and down keys to modify the selection
F11.04 0011
down keys (knob) 0: Invalid 1: Used to adjust the frequency keyboard given F01.09 STOP
(0x0B04) (0000~0213)
function selection 2: used to adjust the PID keyboard given F13.01
3: Keyboard up and down keys to modify the parameter number
35 36
AC310 Series Frequency Inverter Manual AC310 Series Frequency Inverter Manual
F11.22 V/F SVC FVC PMVF PMSVC PMFVC 100.0% F12.09 Receive data (address V/F SVC FVC PMVF PMSVC PMFVC 100.0%
Power display factor RUN RUN
(0x0B16) Adjust the output power display of C00.10. (0.0~500.0%) (0x0C09) 0x3000) gain Linearly correct communication data of the address 0x3000. (0.0~500.0%)
37 38
AC310 Series Frequency Inverter Manual AC310 Series Frequency Inverter Manual
39 40
AC310 Series Frequency Inverter Manual AC310 Series Frequency Inverter Manual
F13.25-F13.28: PID Feedback Disconnection judgment F14.07 V/F SVC FVC PMVF PMSVC PMFVC
20.00Hz
Multi-speed 8 (0.00~ Max RUN
(0x0E07) Set PLC multi-speed 8
Parameter frequency)
Factory default Adjustable
Name Content
(Address) (range) properly 10.00Hz
F14.08 V/F SVC FVC PMVF PMSVC PMFVC
V/F SVC FVC PMVF PMSVC PMFVC Multi-speed 9 (0.00~Max RUN
(0x0E08) Set PLC multi-speed 9
V/F SVC FVC PMVF PMSVC PMFVC frequency)
Feedback 20.00Hz
F13.25 0: Continue PID operation without reporting fault 1: Stop and report 0 F14.09 V/F SVC FVC PMVF PMSVC PMFVC
disconnection action STOP Multi-speed 10 (0.00~ Max RUN
(0x0D19) fault (0 ~ 3) (0x0E09) Set PLC multi-speed 10
selection frequency)
2: Continue PID operation and output alarm signal
3: Run at the current frequency, output alarm signal 30.00Hz
F14.10 V/F SVC FVC PMVF PMSVC PMFVC
Feedback Multi-speed 11 (0.00~ Max RUN
F13.26 V/F SVC FVC PMVF PMSVC PMFVC 1.0s (0x0E0A) Set PLC multi-speed 11
disconnection RUN frequency)
(0x0D1A) Set feedback disconnection detection time (0.0~120.0s)
detection time 40.00Hz
F14.11 V/F SVC FVC PMVF PMSVC PMFVC
F13.27 Wire break alarm V/F SVC FVC PMVF PMSVC PMFVC 100.0 Multi-speed 12 (0.00~Max RUN
RUN (0x0E0B) Set PLC multi-speed 12
(0x0D1B) upper limit Set the upper limit of the disconnection alarm (0.0~100.0%) frequency)
F13.28 Wire break alarm lower V/F SVC FVC PMVF PMSVC PMFVC 0.0% 50.00Hz
RUN F14.12 V/F SVC FVC PMVF PMSVC PMFVC
(0x0D1C) limit Set the upper limit of the disconnection alarm (0.0~100.0%) Multi-speed 12 (0.00~Max RUN
(0x0E0C) Set PLC multi-speed 12
frequency)
F13.29-F13.33: PID Sleeping Function
40.00Hz
F14.13 V/F SVC FVC PMVF PMSVC PMFVC
Multi-speed 14 (0.00~Max RUN
Parameter Factory default Adjustable (0x0E0D) Set PLC multi-speed 14
Name Content frequency)
(Address) (range) properly
30.00Hz
V/F SVC FVC PMVF PMSVC PMFVC F14.14 V/F SVC FVC PMVF PMSVC PMFVC
F13.29 0 Multi-speed 15 (0.00~ Max RUN
Sleep selection Set whether sleep is effective RUN (0x0E0E) Set PLC multi-speed 15
(0x0D1D) (0 ~ 1) frequency)
0: off 1: valid
10.00Hz
F14. 15:PLC Operation Mode Selection
F13.30 V/F SVC FVC PMVF PMSVC PMFVC
Sleep frequency (0.00~Max RUN
(0x0D1E) Set sleep frequency Parameter Factory default Adjustable
frequency) Name Content
(Address) (range) properly
F13.31 V/F SVC FVC PMVF PMSVC PMFVC 60.0S
Sleep delay RUN V/F SVC FVC PMVF PMSVC PMFVC
(0x0D1F) Set the time of sleep delay (0.0~3600.0S)
Unit position: cycle mode
F13.32 V/F SVC FVC PMVF PMSVC PMFVC 5.0% 0: Stop after single cycle 1: Continuous cycle 2: Keep the final value
Wake up deviation RUN after single cycle
(0x0D20) Set wakeup deviation (0.0~50.0%)
Ten place: timing unit
F13.33 V/F SVC FVC PMVF PMSVC PMFVC 1.0S F14.15 PLC Operation mode 0: second 1: minute 2: hour 0000
Wake-up delay RUN RUN
(0x0D21) Set wakeup delay (0.0~60.0S) (0x0E0F) selection Hundreds: Power-down storage (0000 ~ 2122)
0: no storage 1: storage
4.17 F14:Multi-speed and Simple PLC Thousands: Startup mode
0: Re-run from the first stage
F14.00~F14.14:Multi-speed given 1: Re-run from the phase of the downtime
2: continue to run for the rest of the downtime phase
Parameter
Name Content
Factory default Adjustable F14.16~F14.30:PLC Operation Time Selection
(Address) (range) properly
10.00Hz Parameter Factory default Adjustable
F14.00 V/F SVC FVC PMVF PMSVC PMFVC Name Content
Multi-speed 1 (0.00~Max RUN (Address) (range) properly
(0x0E00) Set PLC multi-speed 1
frequency) F14.16 PLC 1st stage running V/F SVC FVC PMVF PMSVC PMFVC 10.0
20.00Hz RUN
F14.01 V/F SVC FVC PMVF PMSVC PMFVC (0x0E10) time Set PLC 1st stage running time (0.0~6500.0(s/m/h))
Multi-speed 2 (0.00~ Max RUN
(0x0E01) Set PLC multi-speed 2 10.0
frequency) F14.17 PLC 2nd stage running V/F SVC FVC PMVF PMSVC PMFVC
(0.0~ RUN
30.00Hz (0x0E11) time Set PLC 2nd stage running time
F14.02 V/F SVC FVC PMVF PMSVC PMFVC 6500.0(s/m/h))
Multi-speed 3 (0.00~ Max RUN
(0x0E02) Set PLC multi-speed 3 10.0
frequency) F14.18 PLC 3rd stage running V/F SVC FVC PMVF PMSVC PMFVC
40.00Hz (0.0~ RUN
F14.03 V/F SVC FVC PMVF PMSVC PMFVC (0x0E12) time Set PLC 3rd stage running time
Multi-speed 4 (0.00~Max RUN 6500.0(s/m/h))
(0x0E03) Set PLC multi-speed 4
frequency) 10.0
F14.19 PLC 4th stage running V/F SVC FVC PMVF PMSVC PMFVC
50.00Hz (0.0~ RUN
F14.04 V/F SVC FVC PMVF PMSVC PMFVC (0x0E13) time Set PLC 4th stage running time
Multi-speed 5 (0.00~ Max RUN 6500.0(s/m/h))
(0x0E04) Set PLC multi-speed 5
frequency) 10.0
40.00Hz F14.20 PLC 5th stage running V/F SVC FVC PMVF PMSVC PMFVC
(0.0~ RUN
F14.05 V/F SVC FVC PMVF PMSVC PMFVC (0x0E14) time Set PLC 5th stage running time
Multi-speed 6 (0.00~ Max RUN 6500.0(s/m/h))
(0x0E05) Set PLC multi-speed 6
frequency) 10.0
30.00Hz F14.21 PLC 6th stage running V/F SVC FVC PMVF PMSVC PMFVC
F14.06 V/F SVC FVC PMVF PMSVC PMFVC (0.0~ RUN
Multi-speed 7 (0.00~ Max RUN (0x0E15) time Set PLC 6th stage running time
(0x0E06) Set PLC multi-speed 7 6500.0(s/m/h))
frequency)
10.0
F14.22 PLC 7th stage running V/F SVC FVC PMVF PMSVC PMFVC
(0.0~ RUN
(0x0E16) time Set PLC 7th stage running time
6500.0(s/m/h))
41 42
AC310 Series Frequency Inverter Manual AC310 Series Frequency Inverter Manual
43 44
AC310 Series Frequency Inverter Manual AC310 Series Frequency Inverter Manual
4.19 Terminal Selection Function 12 Zero speed operation 26 Emergency stop 40 Frequency detection 4
13 Upper limit frequency arrival 27 Overload pre-alarm output 1
Terminal X Function Interpretation Terminal X Function Interpretation Terminal X Function Interpretation
4.20 Fault and Warning Code Table
0 No function 21 PID control pause 42 Counter clock input terminal
Note: The numbers in parentheses are fault codes or warning codes (Dec. means decimal).
1 Forward running 22 PID characteristic switching 43 Counter clear terminal
2 Reverse run 23 PID parameter switching 44 DC brake command Keyboard display Keyboard display
Fault name Fault type Fault name Fault type
Pre-excitation command (Dec.) (Dec.)
3 Three-wire operation control (Xi) 24 PID given switch 1 45
terminal E.SC1(1) Accelerated system failure Fault E.LD1(79) Load protection 1 Fault
4 Forward turn 25 PID given switch 2 46 Reserved
E.SC2(2) System failure during deceleration Fault E.LD2(80) Load protection 2 Fault
5 Reverse jog 26 PID given switch 3 47 Reserved E.SC3(3) Constant speed system failure Fault E.CPU(81) CPU timeout failure Fault
6 Free parking 27 PID feedback switching 1 48 Command channel switch to
E.SC4(4) Downtime system failure Fault E.LOC(85) Chip lock Fault
keyboard
Command channel switch to E.OC1(5) Overcurrent in acceleration Fault E.EEP(86) Parameter storage failure Fault
7 emergency pull over 28 PID feedback switching 2 49
terminal
Command channel switch to E.OC2(6) Overcurrent during deceleration Fault E.PLL(87) Phase-locked loop failure Fault
8 Fault reset 29 PID feedback switching 3 50
communication E.OC3(7) Overcurrent at constant speed Fault E.BUS1(91) Expansion card A disconnected Fault
9 External fault input 30 Program run (PLC) pause 51 Command channel switch to
expansion card E.OU1(9) Accelerating overvoltage Fault E.BUS2(92) Expansion card B is broken Fault
10 Frequency increment (UP) 31 Program run (PLC) restart 52 Run prohibition E.OU2(10) Overvoltage during deceleration Fault E.BUS3(93) CAN expansion card failure Fault
Acceleration/deceleration time E.OU3(11) E.BUS4(94)
11 Frequency decrement (DW) 32 53 Forward prohibition Overvoltage at constant speed Fault Other expansion card failure Fault
selection terminal 1
E.LU(13) Undervoltage in operation Fault E.BUS5(95) Other expansion card failure Fault
45 46
AC310 Series Frequency Inverter Manual AC310 Series Frequency Inverter Manual
E.OL1(14) Motor overload Fault E.BUS6(96) Other expansion card disconnection Fault
E.OL2(15) Inverter overload 1 Fault E.CP1(97) Monitor compare output 1 fault Fault 5 Inspection, Maintenance and Guarantee
E.OL3(16) Inverter overload 2 continuous CBC Fault E.CP2(98) Monitor compare output 2 fault Fault
E.OL4(17) Inverter overload 3 Fault E.DAT(99) Parameter setting error Fault 5.1 Inspection
E.ILF(18) Input phase loss Fault E.FA1(110) External extension reserve 1 Fault
The frequency converter consists of semiconductor devices, passive electronic components, and moving devices. These devices have a service life. Even under
E.OLF(19) Three phase output phase loss Fault E.FA2(111) External extension reserve 2 Fault
normal working conditions, some devices may have characteristic changes or failures if they exceed the service life. In order to prevent this phenomenon from causing
E.OLF1(20) U phase output phase loss Fault E.FA3(112) External extension reserve 3 Fault
malfunctions, it is necessary to perform preventive inspection and maintenance such as daily inspection, periodic inspection, and device replacement. It is recommended
E.OLF2(21) V phase output phase loss Fault E.FA4(113) External extension reserve 4 Fault
to check every 3 or 4 months after installation.
E.OLF3(22) W phase output phase loss Fault E.FA5(114) External extension reserve 5 Fault
● Daily inspection: In order to avoid damage to the inverter and shorten the service life, please confirm the following items daily.。
E.OH1(30) Rectifier module over temperature Fault E.FA6(115) External extension reserve 6 Fault
Items Content Solution
E.OH2(31) IGBT module over temperature Fault E.FA7(116) External extension reserve 7 Fault
Check if the power supply voltage meets the requirements and whether there Resolve as required on the nameplate.
E.OH3(32) Motor over temperature Fault E.FA8(117) External extension reserve 8 Fault Power supply is a lack of phase power supply.
E.EF(33) External fault Fault Surroundings Whether the installation environment meets the requirements. Confirm the source and solve it properly.
The following is the warning code
E.CE(34) Modbus communication failure Fault Whether the inverter and the motor have abnormal heating and discoloration, Check if the overload, fixing screw, and the heat sink of the
cooling system and check the working status of cooling fans . inverter are dirty, and check if the fan is blocked.
E.HAL1(35) U phase zero drift excessive Fault A.LU1(128) Undervoltage during stopping Warning
Whether the motor has abnormal vibration and abnormal sound. Fasten mechanical and electrical connections and lubricate
E.HAL2(36) V phase zero drift excessive Fault A.OU(129) Overvoltage during stopping Warning Motor
mechanical parts.
E.HAL(37) Sum of Three-phase current is not 0 fault Fault A.ILF(130) Input phase loss Warning Whether the output current of the inverter is higher than the rated value of the Check if an overload condition occurs and confirm that the
Load condition
motor or the inverter for a certain period of time. model of the inverter is selected correctly.
E.HAL3(38) W phase zero drift excessive Fault A.PID(131) PID feedback disconnection Warning
● Regular inspection: In general, it is advisable to conduct regular inspections every 3 months or 4 months, but in actual cases, please determine the actual inspection
E.SGxx(40) Short circuit to ground Fault A.EEP(132) Parameter storage warning Warning
period based on the use of each machine and the working environment.
E.FSG(41) Fan short circuit Fault A.DEF(133) Speed deviation excessive Warning
Items Content Solution
E.PID(42) PID feedback disconnection Fault A.SPD(134) Speed warning Warning
Fasten and replace bad parts; clean and improve the operating
E.COP(43) Parameter copy failure Fault A.GPS1(135) GPS locked Warning overall Insulation resistance check; environmental inspection. environment.
E.PG1(44) PG parameter setting error Fault A.GPS2(136) GPS disconnection Warning ● Replace damaged wires;
● Whether the wires and connections are discolored, whether the insulation is
E.PG2(44) Encoder Z pulse failure Fault A.CE(137) External warning Warning ● Tighten the loose terminals and replace the damaged
Electrical damaged, cracked, discolored, or aged;
terminals;
E.PG3(44) A.LD1(138) connections ● Whether the connection terminals are worn, damaged or loose;
Rotation check error Fault Load protection 1 Warning ● Measure the grounding resistance and tighten the
● Grounding check.
corresponding grounding terminal.
E.PG4(44) Rotational disconnection Fault A.LD2(139) Load protection 2 Warning
Mechanical ● Whether there is abnormal vibration and noise, and whether there is ● Fasten, lubricate, and replace defective parts.
Expansion card disconnection connection looseness.
E.PG5(44) ABZ encoder disconnection Fault A.BUS(140) Warning
warning Semiconductor ● Whether it is contaminated with garbage and dust; ● Whether there is a ● Clean the operating environment; ● Replace damaged
E.PG6(44) Spindle encoder disconnection Fault A.OH1(141) Module over temperature warning Warning components significant change in appearance. parts.
Electrolytic ● Whether it leaks, discolors, cracks, whether the safety valve is exposed, ● Replace damaged parts.
E.PG7(44) Spindle encoder Z pulse error fault Fault A.OH3(142) Motor over temperature warning Warning capacitor swells, ruptures or leaks.
peripheral ● Clean the environment and replace damaged parts.
E.PG8(44) Encoder Z pulse logic fault Fault A.RUN1(143) Run command conflict Warning ● Peripheral device appearance and insulation inspection.
equipment
● Fasten the connector;
E.PG9(44) Spindle encoder Z pulse logic fault Fault A.RUN2(158) Jog terminal start protection Warning A printed circuit ● Whether there is odor, discoloration, severe rust, and the connector is correct
● Clean the printed circuit board;
board and reliable.
E.PG10(44) Encoder Z pulse disconnection Fault A.RUN3(159) Terminal start protection Warning ● Replace damaged printed circuit boards;
● Whether the cooling fan is damaged or blocked; ● Clean the operating environment;
External keyboard disconnection ● Whether the heat sink is stained with dirt, dust and dirt; ● Replace damaged parts.
E.BRU(50) Brake unit failure Fault A.PA2(144) Warning cooling system
warning ● Whether the air inlet and exhaust port are blocked or contaminated with
E.TExx(52) Motor parameter self-learning fault Fault A.COP(145) Parameter copy warning Warning foreign matter.
keyboard ● Whether the keyboard is damaged or defective. ● Replace damaged parts.
E.IAE1(71) Motor angle learning fault 1 Fault A.CP1(146) Monitor comparison output 1 warning Warning ● Fasten mechanical and electrical connections and lubricate
Motor ● Whether the keyboard is damaged or defective. the motor shaft.
E.IAE2(72) Motor angle learning fault 2 Fault A.CP2(147) Monitor comparison output 2 warning Warning
E.IAE3(73) Motor angle learning fault 3 Fault A.FA1(150) External extension reserve 1 Warning : Do not perform related work while the power is on, otherwise there is a danger of death due to electric shock. When performing related work,
please cut off the power supply and confirm that the DC voltage of the main circuit has dropped to a safe level, and wait 5 minutes before performing related work.
E.PST1(74) Synchronous machine out of step fault 1 Fault A.FA2(151) External extension reserve 2 Warning
E.PST2(75) Synchronous machine out of step fault 2 Fault A.FA3(152) External extension reserve 3 Warning
E.PST3(76) Synchronous machine out of step fault 3 Fault A.FA4(153) External extension reserve 4 Warning
E.DEF(77) Speed deviation excessive Fault A.FA5(154) External extension reserve 5 Warning
E.SPD(78) Speed exceed fault Fault A.FA6(155) External extension reserve 6 Warning
47 48
AC310 Series Frequency Inverter Manual AC310 Series Frequency Inverter Manual
5.2 Maintenance
All equipment and components have a service life. Proper maintenance can extend the life, but it cannot solve the damage of equipment and equipment. Please
Appendix I: Modbus Communication Protocol
replace the equipment according to requirements.
Item Service life Item Service life Item Service life
●Communication frame structure
Fans 2~3 years Electrolytic capacitor 4~5 years PCB 8~10 years The communication data format is as follows:
The replacement of other devices is very strict with the maintenance technology and product familiarity, and must be strictly tested before being replaced before use. The composition of the byte: including the start bit, 8 data bits, check bit and stop bit.
Therefore, it is not recommended to replace other internal components. If you do need to replace it, please contact the agent where you purchased the product or the
Start Bit Bit1 Bit2 Bit3 Bit4 Bit5 Bit6 Bit7 Bit8 Check bit Stop bit
sales department of the company.
5.3 Product Warranty The information of a frame must be transmitted in a continuous stream. If the interval of more than 1.5 bytes before the end of the entire frame transmission, the
receiving device will clear the incomplete information and mistakenly believe that the next byte is the address field portion of a new frame. Similarly, if the interval between
1. The product during the warranty period is faulty. For details, please refer to the warranty terms in the warranty card.
the start of a new frame and the previous frame is less than 3.5 bytes, the receiving device will consider it to be the continuation of the previous frame. Due to the disorder
2. Primary fault diagnosis is implemented by customs’ company in principle, but can be provided by our company or our company's service network according to the
of the frame, the CRC check value is incorrect, resulting in communication error.
requirements of your company. According to the results of negotiations with your company, the company will provide free services for the reasons of the failure.
Standard structure of RTU frames:
3. Liability exemption, due to the company's product failure, the inconvenience caused to your company or your company's customers and the damage caused by
non-Company products, whether within the warranty period or not, are not within the scope of the company's responsibility. Frame header 3.5 bytes of transmission time
mailing address:
Slave address
0 to 247 (decimal) (0 is the broadcast address)
03H: Read slave parameters
Command code 06H: Write slave parameters
08H: Loop self-test
Data area Parameter address, number of parameters, parameter value, etc.
49 50
AC310 Series Frequency Inverter Manual AC310 Series Frequency Inverter Manual
Slave address 01H inverter RAM, won’t be stored when power down; if the function code parameter address field high nibble is D, written in the EEPROM, will be stored when
Command code 83H power down.
Fault code 04H For example, parameter F16.xx: 0x50xx (write in RAM) 0xD0xx (stored in EEPROM); parameter F17.xx: 0x51xx (write in RAM) 0xD1xx (stored in EEPROM), and
Low CRC CHK 40H so on other group parameters. When reading the F16~F29 parameter group parameters, the address high nibble is 5, such as reading the parameter F18.xx: 0x52xx.
High CRC CHK F3H ●The error code meaning of slave abnormal response information
Code Description Code Description Code Description
1 Command code error 3 CRC check error 4 Illegal address
●Communication control parameter group address description
Parameter cannot be modified The inverter is busy (EEPROM is
Address 5 Illegal data 6 8
during running being stored)
Function Description Data meaning Characteristics
Definition Reserved parameter cannot be The number of bytes is incorrect when
9 Parameter value exceed 10 11
modified reading parameter.
Communication given 0x3000 or 0x2000 0~32000 correspond to 0.00Hz~320.00Hz W/R
frequency
0x0005:Dec stop
0x0000:no command 0x0006:free stop
0x0001:FWD run 0x0007:Fault reset
Communication command
0x3001 or 0x2001 0x0002:REV run 0x0008:Run prohibition W/R
setting
0x0003:FWD Jog command
0x0004:REV Jog 0x0009:Run permission
command
Bit0 0:Stop status 1:Running status
Bit1 0:Non-Acc 1:Acc status
status
0:Non-Dec
Bit2 1:Dec status
status
Inverter status 0x3002 or 0x2002 Bit3 0:Foward 1:Reverse R
Bit4 0:No fault 1:Inverter fault
Bit5 0:GPRS unlock 1:GPRS locked
Bit6 0:No warning 1:Inverter
Inverter fault code 0x3003 or 0x2003 Inverter current fault code (see faultwarning
code table) R
Communication given upper
0x3004 or 0x2004 0~32000 correspond to 0.00Hz~320.00Hz W/R
limit frequency
Communication torque setting 0x3005 or 0x2005 0~1000 correspond to 0.0~100.0% W/R
Torque control positive
0x3006 or 0x2006 0~1000 correspond to 0.0~100.0% W/R
maximum frequency limit
Torque control reverse
0x3007 or 0x2007 0~1000 correspond to 0.0~100.0% W/R
maximum frequency limit
Communication given PID set
0x3008 or 0x2008 0~1000 correspond to 0.0~100.0% W/R
value
Communication given PID
0x3009 or 0x2009 0~1000 correspond to 0.0~100.0% W/R
feedback value
Fault and warning code
0x3010 or 0x2010 Fault code:0~127 Warning code:128 and above R
reading
External inverter output terminal,
Bit0 – Y
Output terminal status 0x3018 or 0x2018 Bit1-- TA1-TB1-TC1; R
Bit2 – extended Y1 (with IO expansion card)
BIT3 -- Extended relay (with IO expansion card)
AO output 0x3019 or 0x2019 0-10000 correspond to Output 0-10V/0-20mA R
Note: For other function code addresses, see the “Address” column in the function code profile
When using the writing command (06H) to write the F00~F15 parameters, if the function code parameter address field high nibble is 0, only write in the
inverter RAM, won’t be stored when power down; if the function code parameter address field high nibble is 1, written in the EEPROM, and will be stored
when power down.
For example parameter F00.xx: 0x00xx (write in RAM), 0x10xx (stored in EEPROM); parameter F01.xx: 0x01xx (write in RAM) 0x11xx (stored in EEPROM), and so
on, for other parameters. When reading the F00~F15 parameter group parameters, the address high nibble is 0, such as reading the parameter F03.xx: 0x03xx.
When using the write command (06H) to write F16~F29 parameters, if the function code parameter address field high nibble is 5, only write in to the
51 52
AC310 Series Frequency Inverter Manual AC310 Series Frequency Inverter Manual
The operation is in one direction. This mode is the most commonly used two-wire mode. The factory default is to determine the forward and reverse running of the
motor by the X1 (forward running) and X2 (reverse running) terminal commands. As shown below:
X1 (forward rotation operation), and the direction is controlled by the reverse rotation operation terminal X2 (reverse rotation operation). The three-wire operation control
frequency inverter
SB1 SB2 X1
run order(run while on)
2: 3-line 1
53 54