Professional Documents
Culture Documents
WLGP - Wafa Plants Desert Plant Project Specification 110/WA/02 J-53-S-Z-0001-00 F1 0-2465 S-53-1222-001J F1
WLGP - Wafa Plants Desert Plant Project Specification 110/WA/02 J-53-S-Z-0001-00 F1 0-2465 S-53-1222-001J F1
WLGP - Wafa Plants Desert Plant Project Specification 110/WA/02 J-53-S-Z-0001-00 F1 0-2465 S-53-1222-001J F1
INDEX
1.1. References
1.2. Measure systems
1.3. Codes
1.4. Climatic conditions (WAFA)
1.5. Raw materials, products, chemicals, catalyst and wastes specification
1.6. Documents Code
1.7. Safety Criteria
1.8. Engineering standard and specifications
1.9. Reference levels
1.10. Soil Report
1. STEAM OUT
2. DEMINERALIZED WATER, BFW
3. RAW, TREATED, COOLING, FIRE, POTABLE WATERS
4. FUEL
5. COMPRESSED AIR, NITROGEN
6. ELECTRICITY
7. HOT OIL
8. BLOW-DOWN AND FLARE
9. DRAINAGE AND SEWERS
10. NOISE SPECIFICATION
11. RADIATION SPECIFICATION
12. WASTE WATER EFFLUENT SPECIFICATION
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
1.1. References
- Language: English
YES NO
Process Units:
Utility Systems:
Flare 230
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
AFNOR
DIN
UNI
Millimeters Millimeters
Inches Fahrenheit
Millimeters Centigrade/Kelvin
kg/cm² GPM
atm kg/h
bar lb/h
kPa
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
kg m²/cm²/mm²
lb Sq.inch./Sq. feet
kg/m³ m³/h
lb/ft³ ft³/h
°API kg/h
kg/h kWh
lb/h kJ
kcal
Btu
kW Btu/hft 2
kJ/h
kcal/h
Btu/h
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
1.3. Codes
Performance of the contract shall be in conformity with the listed revision of the applicable sections of the
codes. local laws, or accepted engineering practice, as per Attachment 4.
Further information are given in the “Environmental and Meteo Study for Wafa” (T-51-T-V-0001-00).
1.4.1. Temperature
a. Minimum value 9%
1.4.4. Wind
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
- roofs: 1
- paved floors: 0.85
- greens: 0.20
1.4.6. Earthquake
YES NO
SPECTRUM: N.A.
YES NO
due to presence of /
YES NO
YES NO
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
1.5.2. Products
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
1.5.3. Chemicals
Molecular sieves
1.5.5. Wastes
Waste water
1.5.6. Other
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
optimization of lay-out for onsite and offsite facilities (spacing among equipment, division into fire
areas, equipment stacking, escape routes, proper tank bunding, etc.) to reduce consequences of
accidental spills;
use of high quality standards for the engineering of equipment and piping, based on hazardous
characteristics and operating conditions of fluids to be handled;
limitation of ignition sources (proper selection of electrical and instrument equipment based on area
classification drawings);
safe disposal of hazardous substances (by means of flare and closed drain systems);
accidental releases prevention and mitigation (by means of ESD systems, remote operated valves,
flammable/toxic gas detectors network, active and passive fire protection);
proper selection of equipment for personnel protection.
Main codes to be followed to ensure a safe design will be NFPA and API.
Project Specifications and other project drawings will incorporate and expand such criteria.
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
Engineering project specification for each discipline have been prepared by TP Contractor. The project
specifications are based on standards and Company standard specifications.
The following Company standards and Company standard specifications have been taken, per each
discipline, as reference:
- 04930 EQP MEC SPC GEN. SPC. TRAYS FOR COLUMN (AMEND. BY TP SPEC)
- 04931 EQP MEC SPC GEN. SPC STORAGE TANKS
- 05490 MAT MEC SPC GEN. SPC FOR FABRICATION AND TESTING OF CARBON STEEL PRESSURE
VESSELS
- 04937 EQP MEC SPC TUBE BUNDLE HEAT EXCHANGERS
- 06586 MAC MEC SDS AIR COOLER
- 20182 COO GEN SDS SPARE PARTS (AMEND BY TP SPEC)
- 07000 EQP MEC STD VESSEL TOLERANCES
- 07001 EQP MEC STD NAMEPLATE FOR PRESSURE VESSEL
- 07002 EQP MEC STD NAMEPLATE FOR JACKETED PRESSURE VESSELS
- 07003 EQP MEC STD NAMEPLATE HOLDER FOR VESSELS
- 07004 EQP MEC STD CATALYST LOADING & UNLOADING ACCESSORIES
- 07005 EQP MEC STD CATALYST LOADING HOPPER
- 07006 EQP MEC STD CATALYST UNLOADING SPOUT
- 07007 EQP MEC STD CATALYST LOADING CANVAS TUBES
- 07008 EQP MEC STD DRUM AND BARREL TILT DEVICE
- 07009 EQP MEC STD SUPPORT SKIRTS AND ANCHOR BOXES
- 07010 EQP MEC STD VERTICAL VESSEL SUPPORTING LEGS
- 07011 EQP MEC STD LUG SUPPORTS FOR VERTICAL VESSELS
- 07012 EQP MEC STD SUPPORT SADDLES FOR VESSELS
- 07013 EQP MEC STD DIMENSIONS OF TRAY SUPPORT RINGS
- 07014 EQP MEC STD VORTEX BREAKER FOR LEVEL CONNECTION
- 07015 EQP MEC STD VORTEX BREAKERS
- 07016 EQP MEC STD VORTEX BREAKERS
- 07017 EQP MEC STD VORTEX BREAKERS
- 07018 EQP MEC STD VORTEX BREAKERS
- 07019 EQP MEC STD VORTEX BREAKERS
- 07020 EQP MEC STD MANHOLE SUPPORT
- 07021 EQP MEC STD MANHOLE OR HANDHOLE HINGES
- 07022 EQP MEC STD VESSEL INSULATION SUPPORTS
- 07023 EQP MEC STD GUNITE LINING ANCHORS FOR VESSELS
- 07024 EQP MEC STD INSULATING CONCRETE ANCHORS
- 07025 EQP MEC STD NOZZLES FOR VESSEL
- 07026 EQP MEC STD ANGLE NOZZLES FOR VESSEL
- 07027 EQP MEC STD ANGLE NOZZLES FOR VESSEL
- 07028 EQP MEC STD NOZZLE DETAILS FOR CLAD OR LINED VESSELS
- 07029 EQP MEC STD TANGENTIAL INLET WITH ANTI-EROSION PLATE
- 07030 EQP MEC STD INLET WITH ELBOW AND ANTIEROSION PLATE ON HORIZONTAL VESSELS
- 07031 EQP MEC STD TANGENTIAL DISTRIBUTOR FOR VERTICAL VESSELS
- 07032 EQP MEC STD INLET WITH OPEN DISTRIBUTOR
- 07033 EQP MEC STD INLET WITH SLOTTED DISTRIBUTOR
- 07034 EQP MEC STD INLET WITH ANGLE CUT
- 07035 EQP MEC STD CENTRAL INLET WITH ELBOW
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
- 07118 EQP MEC STD HEAT EXCHANGERS: LONGITUDINAL BAFFLE WITH SEALING STRIPS
- 07211 EQP MEC STD GENERAL CONSTRUCTION NOTES
- 07212 EQP MEC STD SYMBOLS - REFERENCES AND MISCELLANEOUS
- 07213 EQP MEC STD STD WELDED KNEES FOR FRAME
- 07214 EQP MEC STD BOLDED KNEES FOR FRAME
- 07215 EQP MEC STD BOLTED ATTACHMENTS FOR BEAMS ON COLUMNS
- 07216 EQP MEC STD BOLTED ATTACHMENTS FOR BEAMS ON COLUMNS
- 07217 EQP MEC STD BRACING KNOTS WITH BEAM CONNECTION
- 07218 EQP MEC STD CONNECTION OF BEAMS ONLY
- 07219 EQP MEC STD VERTICAL LADDERS
- 07220 EQP MEC STD STAIRS
- 07221 EQP MEC STD HANDRAIL-TOE BOARD
- 07222 EQP MEC STD BRACKETS FOR INTERMEDIATE CIRCULAR PLATFORMS
- 07223 EQP MEC STD CIRCULAR PLATFORMS FOR COLUMNS AND VESSELS
- 07224 EQP MEC STD CIRCULAR PLATFORMS FOR VESSELS
- 07225 EQP MEC STD DAVIT FOR VERTICAL VESSELS
- 07227 EQP MEC STD SKETCH FOR CARPENTERY PACKING
- 07228 EQP MEC STD TYPICAL CONNECTIONS FOR LADDERS AND PLATFORMS ON CIRCULAR
VESSELS
- 07229 EQP MEC STD TYPICAL CONNECTIONS FOR TOP PLATFORMS
- 07230 EQP MEC STD SUPPORTS FOR DAVIT FOR VERTICAL VESSELS
- 07231 EQP MEC STD SYMBOLS AND REFERENCES FOR LADDERS AND CIRCULAR PLATFORMS
- 07232 EQP MEC STD TYPICAL CONNECTIONS FOR PLATFORMS ON HORIZONTAL VESSELS
- 07233 EQP MEC STD SAFETY LOOK
- 07250 EQP MEC STD PLATFORMS ON CYLINDRICAL VESSELS-MINIMUM AMPLITUDE OF PLATFORMS
- 07251 EQP MEC STD PLATFORMS ON CYLINDRICAL VESSELS-MINIMUM AMPLITUDE OF PLATFORMS
- 07252 EQP MEC STD PLATFORMS ON CYLINDRICAL VESSELS-MINIMUM AMPLITUDE OF PLATFORMS
- 07253 EQP MEC STD PLATFORMS ON CYLINDRICAL VESSELS-MINIMUM AMPLITUDE OF PLATFORMS
- 07254 EQP MEC STD PLATFORMS ON CYLINDRICAL VESSELS-MINIMUM AMPLITUDE OF PLATFORMS
- 07255 EQP MEC STD PLATFORMS ON CYLINDRICAL VESSELS-MINIMUM AMPLITUDE OF PLATFORMS
- 07256 EQP MEC STD PLATFORMS ON CYLINDRICAL VESSELS-MINIMUM AMPLITUDE OF PLATFORMS
- 07300 EQP MEC STD STORAGE TANKS - JOINTS PREPARATION FOR WELDING
- 07302 EQP MEC STD FIXED AND FLOATING ROOF STORAGE TANKS - BOTTOM DRAW OFF WITH SUMP
- 07305 EQP MEC STD STORAGE TANKS-SHELL NOZZLE FOR STEAM AND CONDENSATE
- 07308 EQP MEC STD CONE ROOF TANKS-SHELL MANHOLE WITHOUT REINFORCING
- 07309 EQP MEC STD STD EXTERNAL STAIRWAY FOR STORAGE TANKS
- 07311 EQP MEC STD STORAGE TANKS - VERTICAL LADDER WITH CAGE
- 07312 EQP MEC STD CONE ROOF TANKS - VERTICAL LADDER
- 07314 EQP MEC STD BOTTOM ANCHOR PLATES
- 07316 EQP MEC STD FIXED AND FLOATING ROOF STORAGE TANKS -DETAILS-
- 07318 EQP MEC STD FIXED ROOF TANKS - INSULATION RINGS SUPPORT
- 07322 EQP MEC STD CONE ROOF TANKS - FLAME TRAP VENT
- 07323 EQP MEC STD CONE ROOF TANKS - FLAME TRAP VENT
- 07324 EQP MEC STD CONE ROOF TANKS - OPEN VENT
- 07325 EQP MEC STD FIXED ROOF STORAGE TANKS - CIRCUMFERENTIAL HANDRAIL
- 07326 EQP MEC STD FLOATING ROOF TANKS: MIND GIRDER HANDRAIL
- 07329 EQP MEC STD FOAM DISTRIBUTOR FOR FLOATING ROOF
- 07330 EQP MEC STD STORAGE TANKS - SPRAY NOZZLE
- 07331 EQP MEC STD FLOATING ROOF TANKS - PROTECTIVE SHIELD
- 07335 EQP MEC STD STORAGE TANKS - VERTICAL LADDER – INTERNAL
- 07340 EQP MEC STD STORAGE TANKS – GROUNDING
- 07341 EQP MEC STD FLOAT ROOF TANKS GUIDE POLE WITH GAUGE HATCH NOZZLE
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
- 07342 EQP MEC STD FLOATING ROOF TANKS GUIDE POLE AUTOMATIC LEVEL INDICATOR NOZZLE
- 07343 EQP MEC STD FLOATING ROOF TANK: TOP PLATFORM
- 07344 EQP MEC STD AUTOMATIC LEVEL INDICATOR ASSEMBLY
- 07346 EQP MEC STD STORAGE TANKS - DIP PLATE
- 07347 EQP MEC STD NAMEPLATE FOR STORAGE TANKS
- 07348 EQP MEC STD JET MIXER
- 07349 EQP MEC STD WORKING HEIGHT DEFINITION
b) Piping
- 06285 DOC GEN PRG MECHANICAL EQUIPMENT ARRANGEMENT DRAWING EXECUTION CRITERIA (*)
- 05892 PIP MEC SDS PIPES AND PIPING COMPONENTS FOR PLANTS (*)
- 05329 PIP MEC PRG PIPING SUPPORTS (**)
- 06594 VAR GEN PRG SIZING AND ESTIMATING LOADS ON PIPE RACK (**)
- 05862 PIP MEC SPT STANDARD PIPING SUPPORTS (**)
- 05863 PIP MEC SPT TYPICAL PIPING SUPPORTS (**)
- 07616 PIP MEC SPT PIPING SUPPORTS (**)
- 20199 VON SAF SDS ONSHORE INSTALLATION – SAFETY GENERAL CRITERIA
- 20243 VON SAF SDS ONSHORE INSTALLATION – DESIGN LAYOUT AND SAFETY SPACING
- 0586 OPT GEN PRG ONSHORE PLANT – GENERAL DESIGN CRITERIA
C) Material
- 02555 VAR COR PRG INTERNAL CORROSION – CORROSION PARAMETERS AND CLASSIFICATION OF
THE FLUIDS
- 03580 MAT COR PRG INTERNAL CORROSION – METALLIC MATERIALS IN CONTACT WITH SEA WATER
- 06574 VAR PRC SPC SPC GEN STUDIO SUGLI INIBITORI DI CORROSIONI
- 03587 MAT COR PRG DESIGN CRITERIA – MATERIAL REQUIREMENTS FOR H2S CONTAINING
ENVIRONMENTS
- 03588 MAT COR PRG INTERNAL CORROSION – MATERIALS AND MATERIALS SELECTION CRITERIA
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
d) Electrical
AGIP SPECIFICATIONS
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
d) Insulation
e) Instrumentation
J-51-S-I-0002-00
See T-50-S-I-0002-00 – “Company Standards for Instrumentation and Automation”
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
1.9.1. Plant elevation is 675 meters in respect of the National Vertical Datum.
1.9.2. Plant reference levels are established from the elevations of pertinent terraces.
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
Available YES NO
a. if yes, nature of soil: With respect to mechanical properties of material, two geotechnical strata
can be recognised in the foundation soil. The upper layer consists of clayey
and silty snad/gravel and the thickness varies from 0.45 to 3.8 m. The
lower layer consists of rock. The upper part of the rock layer is always the
limestone which may change into other type of rock as depth increases.
The upper part of the rock layer is moderately to highly weathered.
The analysis of information from boreholes and test pits justify the
conclusion that a matrix of soil consists of coarse material, sand and
gravel. This material determines mechanical properties of the whole mass
of soil. The soil characteristics based on the observed heterogeneity of the
soil, between the locations of planned facilities do not substantially differ.
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
The following definitions have to be considered as starting point for detailed analysis and development of
Design Basis. They have to be checked and confirmed by Discipline coordinators during development of
Design Basis and Philosophies.
See attachment 2
ONSITE OFFSITE
- Fire Water X X
- Cooling Water X X
- Potable Water X X
- Winning Water X X
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
2.3. Instruments
Pneumatic
Electronic (Smart)
Dedicated PLC
Console (DCS)
Semi-graphic Graphic
Conventional Miniature
DCS (Sequences)
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
Integrated in PLC
(ESD alarms)
NO YES Future
Data acquisition
Set-point control
Pneumatic Electro/pneumatic
Electric
Hydraulic
Conduit Trays
Conduit
In trenches
Sunshield Header
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
Prefabricated
UPS redundant
Solar panels
PLC based
Data acquisition
Radio Link
Wire
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
2.4. Insulation
2.4.1. General
YES NO
As required
Hot insulation
Cold insulation
Antisweet insulation
Pers. Prot.
Winterizing
Steam tracing
Electr. tracing
Hot oil tracing
Contractor
Insulation design Technip Italy Client Other
Material ......................
Application ......................
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
2.4.2. Piping
a. Hot insulation
b. Cold insulation
c. Personnel protection
f. Steam tracing
g. Electrical tracing
imposed calculated
- Tracing size(s) HOLD
- Tracing material HOLD
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
2.6. Painting
- Normal
- Marine
- Light industrial
- Heavy industrial
- Corrosive for
YES NO
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
2.7. Buildings
2.7.1. Drawings and technical report for Municipal Authorities will be prepared.
YES NO
2.7.2. Drawings and technical report for Antifire Safeguard Authorities will be prepared.
YES NO
2.7.3. Calculation for reinforced concrete structures and for steel structures for Authorities approval will be
prepared.
YES NO
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
2.8.1.1. Systems
VHF UHF
Conventional EEx-d
Weather proof
Conduit Trays
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
Multimode F.O. cable (short dist.) Single mode F.O. cable (long dist.)
2.8.3.1. Laboratory
EMT conduit
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
3. STEAM OUT
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
C PRESSURE (barg)
min
O - Operating normal 6,4 6
max
N
D - Design 10 10
I TEMPERATURE (°C)
T min
- Operating normal AMB AMB
I max
O
- Design 70 70
N FOULING FACTOR 0,0002 0,0002
S (°C m2 h Kcal)
pH 7 9
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
5. RAW WATER, TREATED WATER, COOLING WATER, FIRE WATER, POTABLE WATER
N
Pressure - Operating (2) 4 2 6 3 11
D (barg)
I
N
- Design 70 70 70
S
H -- -- --
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
3. RAW WATER, TREATED WATER, COOLING WATER, FIRE WATER, POTABLE WATER
N
Pressure - Operating (1) 5,5 4/5,5 25
D (barg)
I
T - Design 10 10 33
S
- Design 70 70 70
C pH
N H2S
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
6. FUEL
D
Temperature - Operating AMB AMB
I (°C) - Design 70 70
S Calcium
I ASH
S Hydrogen sulphide
Water content ppm 800 50
Solid content mg/l 12
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
SYMBOL
Design 12 12 12
(°C) Design 70 70 70
OIL ppm Wt, Max. oil free oil free Oil free
NOTES:
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
8. ELECTRICITY
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
9. HOT OIL
GENERAL NOTE: The pressures and temperatures specified in this attachment will be used for users design.
Physical properties:
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
YES NO
YES NO
Is scope of Technip Italy to check the suitability of the existing relief system to be connected to the new
one?
YES NO
YES NO
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
YES NO PARTIALLY
Drains to be collected
Materials
Combined with
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
J-51-SQ-0001 00
See: T-50-SQ-0001 00 Equipment Noise Specification
J-50-SQ-0002 00
T-50-SQ-0002 00 Plant Noise Control Specification
FLARES:
BURN PIT:
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.
Contract No. Company Doc. No. Rev.
Notes : 1) The temperature increase in the receiving body shall not be greater than 3°C at 1 km from offtake point
and in any direction
2) Not detectable after dilution 1 : 20
3) Not disagreeable
4) NfC : Number from Count
5) Hydrocarbons as Suspended Oils <15 ppm
Note : This specification is sourced from ITT design premises T-53-S-Z-0001-00. All the data in this specification unless marked-up are identical to
original ITT design premises.