Professional Documents
Culture Documents
PUB Corenet Form Changes
PUB Corenet Form Changes
Table of Contents
Summary of Corenet Form Changes ............................................................................................ 1 – 6
Forms with Changes ............................................................................................................................ 1
Forms with No Changes ...................................................................................................................... 6
PUB-DD-CHECKLIST Checklist for Drainage DC Plans PUB (C&W) Checklist will be a section of the DC form
(No need for separate checklist to be submitted)
PUB-BPU-CLRDP01 Application for Clearance Certificate Drainage DP, Sewerage DP, Sewerage Form A, Sewerage Form D, and Sewerage
for Detailed Plan on Drainage and RC Trench combined into 1 form. Previously known as PUB-DD-CLRDPDRA01 &
Sewerage (Sanitary/Sewer) Works PUB-SEW-CLRDPSEW01.
• For Form A, Form DP, Form D, Form D1 and Form D2, please fill Section
A1: Sanitary Work
• For RC Trench, please fill Section A2: Sewerage Work, RC Trench
PUB-BPU-COMPOFWORK Certificate of Completion and All completion of work forms for sewerage, sanitary and M&E to merge into one
(for Completion of SEW Work only) Inspection of Sanitary, Sewerage and form. Previously known as Form C, Form C1, Annex A, Annex C and Annex D.
Drainage Works
• Form C is replaced by the COMPOFWORK form
• For Annex A, Annex C and Form C1, please fill Section A2: Sanitary Work
• For Annex D, please fill Section A1: Sewerage Work
• For PUB-SEW-RC TRENCH, please fill Section A3: RC Trench Completion
1
File Number Form Name Changes
PUB-BPU-COMPOFWORK Certificate of Completion and It is known that these different forms are submitted by different QPs at different
(for Completion of SEW Work only) Inspection of Sanitary, Sewerage and stages of the development of the project. Hence built into the form is a feature
Drainage Works which allows one particular section of the form to be submitted.
For example, if only the PE (Civil) is ready to make his submissions, he can
proceed to do so using the form. If more than one QP/PE is ready to make
theirs, more sections of the form may be submitted at the same time by
selecting the relevant sections.
ENV-CBPU-CLRTOP01-NEW SUBMISSION Application for Clearance of New declarations added for developer/owner to endorse with regards to:
Temporary Occupation Permit (TOP) • maximum allowable peak surface runoff stipulated in the COP and
- New Submission constructed according to approved plans
• SOP of the maintenance, operation and monitoring of the detention
tank system
• Inspection of crest levels being constructed to approved plans
ENV-CBPU-CLRTOP01-RESUBMISSION Application for Clearance of
annually/every 3 years upon obtaining the TOP
Temporary Occupation Permit (TOP)
- Resubmission • Submission of the following documents as required annually upon
obtaining the TOP
2
File Number Form Name Changes
ENV-CBPU-CLRCSC01-NEW SUBMISSION Application for Compliance Attachments section modified to comply with revised Code of Practice on
Certificate - New Submission Surface Water Drainage.
ENV-CBPU-CLRCSC01-RESUBMISSION Application for Compliance Attachments section modified to comply with revised Code of Practice on
Certificate – Resubmission Surface Water Drainage.
PUBWTR-0-PPC01 Pre-Planning Consultation Modified fields to indicate water demand for Potable and NEWater.
PUBWTR-0-WLP01 Notification of Water Service Work Modified fields to indicate water demand for Potable and NEWater.
by Licensed Water Service Plumber
PUBWTR-0-WSW01 Notification of Water Service Work Modified fields to indicate water demand for Potable and NEWater.
by Professional Engineer
PUBWTR-0-CSC01 Certificate of Satisfactory Added new section - “Particulars of the Licensed Water Service Plumber”
Completion of Water Service Work
by Professional Engineer
PUBWTR-0-MCG01 Form for Manufacturing Category Include fields to indicate water demand for Potable and NEWater.
PUBWTR-0-NMC01 Form for Non-Manufacturing Include fields to indicate water demand for Potable and NEWater.
Category
PUBWTR-0-RCG01 Form for Residential Category Include fields to indicate water demand for Potable and NEWater.
PUBWTR-0-TSP01 Form for Temporary Category Include fields to indicate water demand for Potable and NEWater.
3
File Number Form Name Changes
PUB-SEW-FORM_C Certificate of Completion and Not in Use from 28 Feb 2014
Inspection for Sanitary / Sewerage
Works
PUB-SEW-FORM_D1 Details of Standby Generator & Not in Use from 28 Feb 2014
Automatic Transfer Switch
PUB-SEW-FORM_DP Application for Clearance Certificate Not in Use from 28 Feb 2014
for Detailed Plans on Sewerage
(M&E Works)
4
File Number Form Name Changes
PUB-SEW-ANNEX_D Hydrostatic (Water) Tests for Not in Use from 28 Feb 2014
Sanitary Drainlines & Sewers
(<600mm DIA) and CCTV Inspection
Survey (>600mm DIA Sewers)
[Annex D to Form C/QP]
PUB-SEW-RC TRENCH Certificate of Completion for RC Not in Use from 28 Feb 2014
Trench
PUBWTR-0-WSP01 Application for License As a Water Not in Use from 28 Feb 2014
Service Plumber
PUBWTR-0-WSR01 Application for Renewal of Water Not in Use from 28 Feb 2014
Service Plumber Licence
PUBWTR-0-PWS01 Application for Potable Water Not in Use from 28 Feb 2014
Supply
5
Forms with No Changes
PUB-SEW-FORM DLP End of Defects Liability Period Inspection for Public Sewers
PUBWTR-0-WSW02 Certification of Satisfactory Completion of Water Service Work by Licensed Water Service Plumber
6
Corenet Forms with Changes
6
1.1 Guide for Development Control (DC) Clearance Forms
ENV-CBPU-DCCLR-NEW SUBMISSION
Application for Development Control (DC) Clearance – New Submission
a) The DC clearance form is updated to support the work flow process. As part of an effort to
improve our service to the industry, PUB has introduced the classification of projects into
major and minor. This allows processing through separate tracks so that minor projects can be
processed more quickly.
d) For minor projects, QPs may submit both the DC plan and Detailed Plan (DP) at the same time,
allowing for shorter processing time. Previously, QPs need to obtain DC clearance before DP
can be submitted.
7
e) On the second page of the forms, there is a section called Development Details. This section
must be filled to allow the sorting of the project – into major or minor – to take place.
Accurate information is necessary to facilitate processing of the submissions.
Note
If a single dwelling unit has > 5 persons, please use the appropriate number of occupants in your
calculation.
If a development is using an ejector for its discharge to sewerage system, then the total used water
discharge rate should include the discharge rate of the ejector.
If in doubt you may wish to engage a licensed plumber or M&E professional engineer for an estimate
of the discharge from the premise.
Please refer to Section 1.2 for more information on the “Select” fields and how they can affect
your submissions.
f) For projects sorted as minor, QP will be directed to the next section – “SUBMISSION FOR
DEVELOPMENTAL CONTROL (DC) CLEARANCE WITH DETAIL PLAN”.
8
g) For projects sorted as major, QP will be directed to the next section – “SUBMISSION FOR
DEVELOPMENTAL CONTROL (DC) PLAN”.
h) There are sections in the form that must be selected and filled only when the project involves
the respective sections. For example, if the project involves:
(i) sanitary / sewerage work, Section A needs to be selected and filled
(ii) sanitary / sewerage AND drainage work, Sections A and B need to be selected and filled
j) If the box is unchecked, the whole section will be greyed out and the QP will not be able to fill
that particular section.
k) Compulsory fields within these sections must be duly filled only when the section is selected
for submission. The sections are listed as follows:
Submission for Development Control (DC) Clearance Plan (for MAJOR projects only)
Section A – Sanitary/ Sewerage Work
Section B – Drainage Work
Submission for Development Control (DC) Clearance with Detail Plan (for MINOR projects only)
Section A1 – Sanitary, M&E Work (Used Water)
Section A2 – Sewerage Work, RC Trench
Section B – Drainage Work
Section C – Infrastructure or other works affecting Sewer & Drainage (e.g. covered linkway,
bus stop)
9
l) To make attachments and declarations, QPs can similarly mark the provided checkboxes.
m) The Catchment & Waterways department’s Checklist for DC plans is now part of the DC
clearance forms. Please fill up the fields in the checklist if the project involves drainage works.
(i) Development site with area less than 0.2 hectares will be directed to the checklist
below.
(ii) Development site with area greater than or equal to 0.2 hectares will be directed to the
checklist below.
10
n) There are a number of “Select” fields that can be found throughout the forms. These fields,
when clicked, will show a drop-down menu with options for the QP to choose accordingly.
Please refer to Section 1.2 for more information on the “Select” fields and how they can affect
your submissions.
o) Compulsory fields are highlighted, as shown in Appendix 1. These must be filled to enable
successful submission of the forms in Corenet.
ENV-CBPU-DCCLR-RESUBMISSION/AMENDMENT/REVISION
Application for Development Control (DC) Clearance –
Resubmission/Amendment/Revision
11
1.2 Select Fields – DC Clearance Forms
Field Detail
Industrial
Factories, warehouses, power plants, industrial parks
Non Industrial
Residential, commercial and institutional developments
This field can be found on Page 41
12
Field Detail
Please choose the catchment where your project is located.
For projects that take place in more than one catchment, please
select one catchment.
13
Field Detail
14
Field Detail
15
Field Detail
16
Field Detail
17
Field Detail
19
Field Detail
21
Field Detail
This field can be found on Page 58 Select NOT APPLICABLE if items are not relevant to the project.
Pumping Installation
A minimum of two pumps – duty and standby pumps – shall be
provided.
Ejector
The pit for the sewage ejector or solids divertor installation shall
be adequately sized (min. 3m x 3m) and shall include a working
space for maintenance.
Sump
A screen chamber shall be provided before the pump sump.
When the depth of pump sump or screen chamber exceeds 6m,
intermediate platforms shall be provided.
Access opening shall be provided directly above the pumps for
ease of maintenance.
Carpark
A screen chamber is NOT needed for carpark pump sump.
Swimming Pool
Backwash from swimming pool filter.
This field can be found on Page 45
22
Field Detail
Particulars of Plumber
Please select the registered plumber/contractor’s name from the
drop – down list. Once selected, the rest of his particulars will
auto – populate in the form.
Type of Plumber
For PUB Licensed Plumber, tick “PUB LP” and input membership
This field can be found on Page 46 – 47 or license number.
23
2.1 Guide for Detailed Plan (DP) Form
PUB-BPU-CLRDP01
Application for Clearance Certificate for Detailed Plan on Drainage and Sewerage
(Sanitary / Sewer) Works
b) Previously, there were two forms for DP submissions, one for sewerage works (PUB-SEW-
CLRDPSEW01) and one for drainage works (PUB-DD-CLRDPDRA01). These two forms are now
combined into one single PUB-BPU-CLRDP01 form.
OLD DP Forms NEW DP Form
PUB-SEW-CLRDPSEW01
PUB-BPU-CLRDP01
PUB-DD-CLRDPDRA01
c) There are sections in the form that must be selected and filled only when the project involves
the respective sections. For example, if the project involves:
(i) sanitary work, Section A1 needs to be selected and filled
(ii) sanitary AND drainage work, Section A1 and Section B need to be selected and filled
e) If the box is unchecked, the whole section will be greyed out and the QP will not be able to fill
that particular section.
f) Compulsory fields within these sections must be duly filled only when the section is selected
for submission. The sections are listed as follows:
Section A1 – Sanitary Work
Section A2 – Sewerage Work, RC Trench
Section B – Drainage Work
24
g) To make attachments and declarations, QPs can similarly mark the provided checkboxes.
h) There are a number of “Select” fields that can be found throughout the forms. These fields,
when clicked, will show a drop-down menu with options for the QP to choose accordingly.
If applying for
drainage clearance
only, please ignore
t this field.
Please refer to Section 2.2 for more information on the “Select” fields and how they can affect
your submissions.
i) Compulsory fields are highlighted, as shown in Appendix 3. These must be filled to enable
successful submission of the forms in Corenet.
25
2.2 Select Fields – DP Form
Field Detail
Sanitary
Includes works on any sanitary plumbing or drainage system and
the fixing, alteration and repair of a sanitary appliance
Sewer
Includes engineering works for the construction, alteration and
maintenance of any sewerage system
Sewage Treatment Plant
This field can be found on Page 92
Refers to sewage treatment works, septic tank, imhoff tank,
percolating filter, sludge digestion tank, or any tank designed for
the pre-treatment, treatment or the stabilisation of sew
Drainage
Leave this field blank if applying for Clearance Certificate for
Detailed Plan on Drainage Work only.
New Submission
First DP submission for the particular project
Resubmission
Subsequent DP submission(s) of the same project
- Revised Plan Submission
This field can be found on Page 92
- Amendment Plan Submission
Industrial
Factories, warehouses, power plants, industrial parks
Non Industrial
This field can be found on Page 92 Residential, commercial and institutional developments
26
Field Detail
Particulars of Plumber
Please select the registered plumber/contractor’s name from the
drop – down list. Once selected, the rest of his particulars will
auto – populate in the form.
Type of Plumber
For PUB Licensed Plumber, tick “PUB LP” and input membership
This field can be found on Page 93 & 95 or license number.
27
Field Detail
Pumping Installation
A minimum of two pumps – duty and standby pumps – shall be
provided.
Ejector
The pit for the sewage ejector or solids divertor installation shall
be adequately sized (min. 3m x 3m) and shall include a working
space for maintenance.
Carpark
A screen chamber is NOT needed for carpark pump sump.
Swimming Pool
Backwash from swimming pool filter.
28
3.1 Guide for Completion of Work Form
PUB-BPU-COMPOFWORK
Certificate of Completion and Inspection of Sanitary, Sewerage and Drainage Works
a) The PUB-BPU-COMPOFWORK form puts together all the Completion of Work forms for
sewerage, sanitary and M&E. These forms were previously known as Form C, Form C1, Annex
A, Annex C and Annex D. This is to give the project QP an overview of the various Completion
of Work forms that has to be submitted to PUB over the course of the project.
b) It is known that these different forms are submitted by different QPs at different stages of the
development of the project. Hence, built into the form is a feature which allows one particular
section of the form to be submitted even if other required sections are not ready for
submission. For example, if only the PE (Civil) is ready to make his submission, he can proceed
to do so using the form even if the PE (Mechanical) is not ready to submit theirs. If more than
one QP is ready to make their submissions, more sections of the form may be submitted at
the same time by selecting the relevant sections.
c) The table below shows the options and the respective sections that will be made available.
The options are available on the first page of the PUB-BPU-COMPOFWORK form.
Selection Options Sections Available for Submission
Completion of Sewerage Section A1 – Sewerage Work
Work only
Application for PUB Section D – Application for PUB Clearance for CSC (For SEW
Clearance for Clearance only)
Certificate of Statutory
Completion (CSC)
29
d) There are a number of “Select” fields that can be found throughout the forms. These fields,
when clicked, will show a drop-down menu with options for the QP to choose accordingly.
Please refer to Section 3.2 for more information on the “Select” fields and how they can affect
your submissions.
e) Compulsory fields are highlighted, as shown in Appendix 4. These must be filled to enable
successful submission of the forms in Corenet. Compulsory fields under the sections A1, A2,
A3, B, C and D must be duly filled only when the section is selected for submission.
30
3.2 Select Fields – Completion of Work Form
Field Detail
31
Field Detail
32
4.1 Guide for Temporary Occupation Permit (TOP) Forms
ENV-CBPU-CLRTOP01-NEW SUBMISSION
ENV-CBPU-CLRTOP01-RESUBMISSION
Application for Clearance of Temporary Occupation Permit (TOP) – New Submission
Application for Clearance of Temporary Occupation Permit (TOP) – Resubmission
b) The following new attachments are added to allow the submission of the following documents
(in line with the current edition of Code of Practice on Surface Water Drainage):
• As – built survey plans indicating crest levels, platform levels, flood protection levels
based on approved flood protection measures
• As – built drawings for detention tank systems and final design calculations, and
factory test report for its pumping system
• Standard Operating Procedure for pumped drainage system(basement / detention
tank)
• Standard Operating Procedure for flood barrier
• Developer/Owner declaration on the following - I shall inspect and declare that the
crest levels are constructed to approved plans annually / every 3 years upon obtaining
the TOP
• Developer/Owner declaration on the following:
- I shall submit the following documents as required annually upon obtaining
the TOP
- Certificate of inspection on flood barriers on site, including leak test
certificate
- Amendments to SOP for flood barrier
- Certificate of inspection on pumped drainage system (basement/detention
tank)
- Certificate of inspection on ABC Waters design features
33
c) To make attachments and declarations, QPs can mark the checkboxes provided.
d) Compulsory fields are highlighted, as shown in Appendix 5 & Appendix 6. These must be filled
to enable successful submission of the forms in Corenet.
34
4.2 Select Fields – TOP Forms
Field Detail
Industrial
Factories, warehouses, power plants, industrial parks
Non Industrial
Residential, commercial and institutional developments
35
5.1 Guide for Certificate of Statutory Completion (CSC) Forms
ENV-CBPU-CLRCSC01-NEW SUBMISSION
ENV-CBPU-CLRCSC01-RESUBMISSION
Application for Compliance Certificate – New Submission
Application for Compliance Certificate – Resubmission
[Under Section 33(7) of the Environmental Protection and Management Act (Chapter 94A) and
Compliance Certificate under Section 33(8) of the Sewerage and Drainage Act (Chapter 294)]
a) To indicate attachments and declarations, QPs can mark the checkboxes provided.
b) Compulsory fields are highlighted, as shown in Appendix 7 and Appendix 8. These must be
filled to enable successful submission of the forms in Corenet.
36
5.2 Select Fields – CSC Forms
Field Detail
Industrial
Factories, warehouses, power plants, industrial parks
Non Industrial
Residential, commercial and institutional developments
37
6.1 Guide to Water Submission Forms
PUBWTR-0-MCG01
PUBWTR-0-NMC01
PUBWTR-0-RCG01
PUBWTR-0-TSP01
PUBWTR-0-PPC01
PUBWTR-0-WLP01
PUBWTR-0-WSW01
PUBWTR-0-CSC01
a) New fields are included to indicate water demand for PUB Water (Potable Water) and
NEWater in the following forms:
File Name Form Name
PUBWTR-0-PPC01 Pre-Planning Consultation
PUBWTR-0-WLP01 Notification of Water Service Work by Licensed
Water Service Plumber
PUBWTR-0-WSW01 Notification of Water Service Work by
Professional Engineer
PUBWTR-0-MCG01 Form for Manufacturing Category
PUBWTR-0-NMC01 Form for Non-Manufacturing Category
PUBWTR-0-RCG01 Form for Residential Category
PUBWTR-0-TSP01 Form for Temporary Category
b) New section is added to indicate the particulars of Licensed Water Service Plumber in the
following form:
File Name Form Name
PUBWTR-0-CSC01 Certificate of Satisfactory Completion of Water Service Work by
Professional Engineer
c) Compulsory fields are highlighted, as shown in Appendix 9 – 16. These must be filled to enable
successful submission of the forms in Corenet.
38
6.2 Select Fields – Water Submission Forms
Field Detail
39
Field Detail
40
Appendix
Appendix 1 ENV-CBPU-DCCLR-NEW SUBMISSION
Date: 19/03/2014
To: Central Building Plan Unit
National Environment Agency
40, Scotts Road #13-00
Environment Building
Singapore 228231
Instructions
1. This form is to be digitally signed by the Qualified Person responsible for the
works.
Particulars of Project
Project Reference Number
Project Title
Location Description
[Include Lot/Plot, MK/TS,
Building Address, House
No and Road information]
Particulars of Application
41
ENV-CBPU-DCCLR-NEW SUBMISSION
Particulars of Qualified Person
Name Select
Role In Project
Registration No
Firm Name
UEN
Firm Address
Telephone No.
Extension No
Fax No.
Email Address
Development Details
development
Area of development ha
42
ENV-CBPU-DCCLR-NEW SUBMISSION
Confirmation
Roof gutters (including rain water down pipes and outlets, and roof scupper
drains) are banned as an anti-mosquito breeding measure for all new
developments. Waiver in writing must be obtained from National Environment
Agency to erect roof gutters at the DC stage prior to BP submission
I confirm that :
a) there are no roof gutters (including rain water down pipes and
outlets, and roof supper drains) provided for in the development
proposal; or
b) waiver for roof gutter has been obtained from the National Environment
Agency in writing on : File Ref No:
Dated:
c) There are roof gutters (including rain water down pipes and outlets,
and roof scupper drains) provided in the development proposal. Waiver
application from ENV-CBPU-WVRG is attached.
d) Confirmation for a), b) or c) not applicable, for A & A and reconstruction
building projects.
Attachments
Development Control Plan
Add Delete
43
SUBMISSION FOR DEVELOPMENT CONTROL (DC)
CLEARANCE WITH DETAIL PLAN
Instruction:
1. This page of the form is applicable for minor projects.
2. First storey plan/site plan for section A1 and B can be submitted as one plan
with clear layer and identification
3. Please check all the relevant infromations have been indicated and provided
before submitting
Particulars of Owner(s)
Name Select
Address
Contact No
Email
(Tick if applicable)
SECTION A1: SANITARY, M&E WORK (Used Water)
Attachments
By QP/PE: Select
I have carried out a
thorough investigation
of the existing
sewerage system within
and adjacent to the site
and will take every
practical measure to
ensure that the
proposed development
will not disrupt or affect
any existing
sewer/drain-line that
serves other properties/
premises.
by QP/PE: Select
I hereby certify that
these plans and the
works shown therein
comply with the
provisions of the
Sewerage and
44
Drainage
Act (Chapter 294),
the Sewerage and
Drainage (Sanitary
Works) Regulations
and the current Code
of Practice on the
Sewerage and Sanitary
Works
by PE(M/E) if there is Select
pumping system(s)
I, being a Professional
Engineer hereby certify
that the propose
mechanical and
electrical(M&E) works
of the above
mentioned project are
design in accordance
with the current Code
of Practice on
Sewerage
and Sanitary Works,
Sewerage and
Drainage
Act (Chapter 294) and
other sewerage
requirements as
stipulated by Water
Reclamation (Network)
Department.
Attachments:
3. Design calculations
Select
Add Delete
45
Particulars of Plumber/Contractor
Name Select
Firm Details
Contact No
Attachments:
by PE (Civil): Select
I hereby certify that
the sewerage plans
and the works shown
therein comply with
the provisions of the
Sewerage and
Drainage
Act (Chapter 294), the
Sewerage and
Drainage
(Sanitary Works)
Regulations, the current
Code of Practice on the
Sewerage and Sanitary
Works.
Particulars of Plumber/Contractor
Tick if same as in Sanitary Work
Name Select
NRIC/Passport No.
Firm Details
Contact No
46
Email
Attachment:
2. Basement Plans
4. DC Checklist
Select
I certify that the drainage
work are designed in full
compliance with PUB
requirements including
Sewerage and Drainage
Act (Chapter 294) and
current edition of COP on
Surface Water Drainage
Attachment:
4. Proposed plan showing crest levels, platform levels with and without
flood barriers at various entrance and exit points, and flood barrier
installed at all pints of entry and exit for building premises or for entire
development.
47
Declaration Name Role Phone Email Firm Arch/PE
Reg No
48
DC SUBMISSION
Particulars of Owner(s)
Name Select
Address
Contact No
Attachments:
1. Site plan and first storey plan
to show: The sewer setback, propose and existing sewer connection,top/invert level of MH, and
platform levels, propose and existing sanitary drainline, propose public sewer (if any), manhole and
sewer identification number
Arch/PE
Declaration Name Role Contact Email Firm
Reg No
49
COP
50
DC SUBMISSION
Attachments:
2. Basement Plans
3. DC Checklist
51
PUB-DD-CHECKLIST
52
Bioretention Swales/Basins Select
(vii) Others
(Please indicate if any)
Detention volume
Detention volume to meet the requirement as stated in Clause 7.1.5 (Please indicate volume
of the latest edition of Code of Practice on Surface Water Drainage in cubic metre)
(Detention V)
53
7. ABC Waters design features are incorporated
within the development. *If yes, please also respond
to 7(a), 7(b)*
54
16. The proposed platform levels and
road/ground levels adjacent to the
internal drain outlet discharge point are
clearly indicated
For developments where flood barriers are automated and/or with more than 2
points of entry/exit, the following document shall be submitted at Detailed Planning
stage.
-- Details on the Standard Operating Procedure (SOP) including the operation and
maintenance of the flood barrier to be endorsed by Mechanical and/ or Electrical
QP or PE, and the developer/ building owner.
-- Details on the size, type and design of the flood barrier.
55
(D) PROPOSED DRAINAGE WORKS
57
(G) PUMPED DRAINAGE SYSTEM
I hereby confirm that the above items have been complied with and endorsed on
the plans.
I hereby certify that the standard endorsement below will also be certified on the
plans:-
(a) The planning, design, construction activities and procedures for plan
submission shall comply fully with the requirements as stipulated in the
latest edition of the Code of Practice on Surface Water Drainage and the
Sewerage and Drainage (Surface Water Drainage) Regulations 2007.
(b) The capacity of internal drains shall be sufficient to intercept and discharge
all runoff from the development site.
(c) The runoff within, upstream of and adjacent to the development lot can be
effectively drained away without causing flooding within the lot or in areas
outside the lot.
(d) There is no direct connection from the internal drains within the basement or
58
sub-basement to the external roadside drains.
* Public Utilities Board (PUB) reserves the right to report any false declaration of
information to the relevant professional bodies for action in accordance to the
Act/ethnics governing all the Qualified Professional.*
59
PUB-DD-CHECKLIST
PUBLIC UTILITIES BOARD (PUB)
CATCHMENT & WATERWAYS DEPARTMENT
CHECKLIST FOR DC PLANS
*Please use this form if development site is less than 0.2 Ha*
(A) General
the development.
(a) Names & Registration No. of ABC Waters
Professional
(b) Concept design and design calculations, Select
60
PUB-DD-CHECKLIST
(B) DRAINAGE RESERVE
indicated on plan
For developments where flood barriers are automated and/or with more than 2 points of
entry/exit, the following document shall be submitted at Detailed Planning/ Building Plan stage.
-- Details on the standard operating procedure (SOP) including the proposed maintenance
plan of the flood barrier to be endorsed by a Civil and/or Mechanical Qualified Person,
and the developer/owner.
-- Details on the size, type and design of the flood barrier.
61
19. Proposed/ existing drains and drains to be deleted Select
are clearly indicated using different colour
20. Alignment, summit point, flow direction, type & size Select
and outlet discharge points of the proposed
internal surface drains are clearly indicated
27. Proposed sizes and flow direction of cut off drains Select
are indicated
62
PUB-DD-CHECKLIST
(F) COMMON DRAIN
28. Alignment, size and flow of existing common drain Select
within the development lot are indicated
I hereby confirm that the above items have been complied with and endorsed on the plans.
63
(a) The planning, design, construction activities and procedures for plan submission shall comply fully
with the requirements as stipulated in the latest edition of the Code of Practice on Surface Water
Drainage and The Sewerage and Drainage (Surface Water Drainage) Regulations 2007.
(b) The capacity of internal drains shall be sufficient to intercept and discharge all runoff from the
development site.
(c) The runoff within, upstream of and adjacent to the development lot can be effectively drained
away without causing flooding within the lot or in areas outside the lot.
(d) There is no direct connection from the internal drains within the basement or sub-basement to the
external roadside drains.
* Public Utilities Board (PUB) reserves the right to report any false declaration of information to the relevant professional
bodies for action in accordance to the Act/ethnics governing all the Qualified Professional. *
64
Appendix 2 ENV-CBPU-DCCLR-RESUBMISSION/AMENDMENT/REVISION
Date: 19/03/2014
To: Central Building Plan Unit
National Environment Agency
40, Scotts Road #13-00
Environment Building
Singapore 228231
Instructions
1. This form is to be digitally signed by the Qualified Person responsible for the
works.
Information
1. For enquiries on application of status, please call 67319681 / 67319513
Particulars of Project
Project Reference Number
Previous DC Clearance
from CBPU (for
amendment/revision)
65
CBPU Processing Officer
given in DC advice/
clearance
Remarks
Role In Project
Registration No
66
ENV-CBPU-DCCLR-RESUBMISSION/AMENDMENT/REVISION
Particulars of Qualified Person (Continue)
Firm Name
UEN
Firm Address
Telephone No.
Extension No
Fax No.
Email Address
Development Details
Area of development ha
67
ENV-CBPU-DCCLR-RESUBMISSION/AMENDMENT/REVISION
Confirmation (Applicable for amendment/revised DC submission only)
Roof gutters (including rain water down pipes and outlets, and roof scupper
drains) are banned as an anti-mosquito breeding measure for all new
developments. Waiver in writing must be obtained from National Environment
Agency to erect roof gutters at the DC stage prior to BP submission
I confirm that :
a) there are no roof gutters (including rain water down pipes and
outlets, and roof supper drains) provided for in the development
proposal; or
b) waiver for roof gutter has been obtained from the National Environment
Agency in writing on : File Ref No:
Dated:
c) There are roof gutters (including rain water down pipes and outlets,
and roof scupper drains) provided in the development proposal. Waiver
application from ENV-CBPU-WVRG is attached.
d) Confirmation for a), b) or c) not applicable, for A & A and reconstruction
building projects.
Attachments
Add Delete
68
SUBMISSION FOR DEVELOPMENT CONTROL (DC)
CLEARANCE WITH DETAIL PLAN
Instruction:
1. This page of the form is applicable for minor projects.
2. First storey plan/site plan for section A1 and B can be submitted as one plan
with clear layer and identification
3. Please check all the relevant infromations have been indicated and provided
before submitting
Particulars of Owner(s)
Name Select
Address
Contact No
Email
(Tick if applicable)
SECTION A1: SANITARY, M&E WORK (Used Water)
Attachments:
By QP/PE: Select
I have carried out a
thorough investigation
of the existing
sewerage system within
and adjacent to the site
and will take every
practical measure to
ensure that the
proposed development
will not disrupt or affect
any existing
sewer/drain-line that
serves other properties/
premises.
by QP/PE: Select
I hereby certify that
these plans and the
works shown therein
comply with the
provisions of the
Sewerage and
69
Drainage
Act (Chapter 294),
the Sewerage and
Drainage (Sanitary
Works) Regulations
and the current Code
of Practice on the
Sewerage and Sanitary
Works
by PE(M/E) if there is Select
pumping system(s)
I, being a Professional
Engineer hereby certify
that the propose
mechanical and
electrical(M&E) works
of the above
mentioned project are
design in accordance
with the current Code
of Practice on
Sewerage
and Sanitary Works,
Sewerage and
Drainage
Act (Chapter 294) and
other sewerage
requirements as
stipulated by Water
Reclamation (Network)
Department.
Attachments:
1. Detail plan drawings of used water pumping system(s)
3. Design calculations
Select
Add Delete
70
Particulars of Plumber/Contractor
Name Select
Firm Details
Contact No
Attachment:
by PE (Civil): Select
I hereby certify that
the sewerage plans
and the works shown
therein comply with
the provisions of the
Sewerage and
Drainage
Act (Chapter 294), the
Sewerage and
Drainage
(Sanitary Works)
Regulations, the current
Code of Practice on the
Sewerage and Sanitary
Works.
Particulars of Plumber/Contractor
Tick if same as in Sanitary Work
Name Select
NRIC/Passport No.
Firm Details
Contact No
71
Email
Attachment:
2. Basement Plans
4. DC Checklist
Select
I certify that the drainage
work are designed in full
compliance with PUB
requirements including
Sewerage and Drainage
Act (Chapter 294) and
current edition of COP on
Surface Water Drainage
Attachment:
4. Proposed plan showing crest levels, platform levels with and without
flood barriers at various entrance and exit points, and flood barrier
installed at all pints of entry and exit for building premises or for entire
development.
72
Declaration Name Role Phone Email Firm Arch/PE
Reg No
73
DC SUBMISSION
Particulars of Owner(s)
Name Select
Address
Contact No
Attachments:
1. Site plan and first storey plan
to show: The sewer setback, propose and existing sewer connection,top/invert level of MH, and
platform levels, propose and existing sanitary drainline, propose public sewer (if any), manhole and
sewer identification number
Arch/PE
Declaration Name Role Contact Email Firm
Reg No
75
COP
76
DC SUBMISSION
Attachments:
2. Basement Plans
3. DC Checklist
77
PUB-DD-CHECKLIST
78
Bioretention Swales/Basins Select
(vii) Others
(Please indicate if any)
Detention volume
Detention volume to meet the requirement as stated in Clause 7.1.5 (Please indicate volume
of the latest edition of Code of Practice on Surface Water Drainage in cubic metre)
(Detention V)
79
7. ABC Waters design features are incorporated Select
within the development. *If yes, please also respond
to 7(a), 7(b)*
80
16. The proposed platform levels and
road/ground levels adjacent to the
internal drain outlet discharge point are
clearly indicated
For developments where flood barriers are automated and/or with more than 2
points of entry/exit, the following document shall be submitted at Detailed Planning
stage.
-- Details on the Standard Operating Procedure (SOP) including the operation and
maintenance of the flood barrier to be endorsed by Mechanical and/ or Electrical
QP or PE, and the developer/ building owner.
-- Details on the size, type and design of the flood barrier.
81
(D) PROPOSED DRAINAGE WORKS
83
(G) PUMPED DRAINAGE SYSTEM
I hereby confirm that the above items have been complied with and endorsed on
the plans.
I hereby certify that the standard endorsement below will also be certified on the
plans:-
(a) The planning, design, construction activities and procedures for plan
submission shall comply fully with the requirements as stipulated in the
latest edition of the Code of Practice on Surface Water Drainage and the
Sewerage and Drainage (Surface Water Drainage) Regulations 2007.
(b) The capacity of internal drains shall be sufficient to intercept and discharge
all runoff from the development site.
(c) The runoff within, upstream of and adjacent to the development lot can be
effectively drained away without causing flooding within the lot or in areas
outside the lot.
(d) There is no direct connection from the internal drains within the basement or
84
sub-basement to the external roadside drains.
* Public Utilities Board (PUB) reserves the right to report any false declaration of
information to the relevant professional bodies for action in accordance to the
Act/ethnics governing all the Qualified Professional.*
85
PUB-DD-CHECKLIST
PUBLIC UTILITIES BOARD (PUB)
CATCHMENT & WATERWAYS DEPARTMENT
CHECKLIST FOR DC PLANS
*Please use this form if development site is less than 0.2 Ha*
(A) General
the development.
(a) Names & Registration No. of ABC Waters
Professional
(b) Concept design and design calculations, Select
86
PUB-DD-CHECKLIST
(B) DRAINAGE RESERVE
indicated on plan
For developments where flood barriers are automated and/or with more than 2 points of
entry/exit, the following document shall be submitted at Detailed Planning/ Building Plan stage.
-- Details on the standard operating procedure (SOP) including the proposed maintenance
plan of the flood barrier to be endorsed by a Civil and/or Mechanical Qualified Person,
and the developer/owner.
-- Details on the size, type and design of the flood barrier.
87
19. Proposed/ existing drains and drains to be deleted Select
are clearly indicated using different colour
20. Alignment, summit point, flow direction, type & size Select
and outlet discharge points of the proposed
internal surface drains are clearly indicated
27. Proposed sizes and flow direction of cut off drains Select
are indicated
88
PUB-DD-CHECKLIST
(F) COMMON DRAIN
28. Alignment, size and flow of existing common drain Select
within the development lot are indicated
I hereby confirm that the above items have been complied with and endorsed on the plans.
I hereby certify that the standard endorsement below will also be certified on the plans:-
89
(a) The planning, design, construction activities and procedures for plan submission shall comply fully
with the requirements as stipulated in the latest edition of the Code of Practice on Surface Water
Drainage and The Sewerage and Drainage (Surface Water Drainage) Regulations 2007.
(b) The capacity of internal drains shall be sufficient to intercept and discharge all runoff from the
development site.
(c) The runoff within, upstream of and adjacent to the development lot can be effectively drained
away without causing flooding within the lot or in areas outside the lot.
(d) There is no direct connection from the internal drains within the basement or sub-basement to the
external roadside drains.
* Public Utilities Board (PUB) reserves the right to report any false declaration of information to the relevant professional
bodies for action in accordance to the Act/ethnics governing all the Qualified Professional. *
90
Appendix 3 PUB-BPU-CLRDP01
Date: 19/03/2014
To: Central Building Plan Unit
National Environment Agency
40, Scotts Road, #13-00
Environment Building
Singapore 228231
Instructions
1. This form is to be digitally signed by the Qualified Person responsible for the
works.
2. This form is to be accompanied by the relevant attachments.
Information
1. For enquiries on application of status for :
a) Industrial development,please call 67319637
b) Non-industrial development,please call 67319628 / 67319653
Particulars of Project
Project Reference Number
Project Title
Location Description
[Include Lot/Plot, MK/TS,
House No, Building
Address and Road
information]
Project Address
91
Particulars of Application
DC Clearance Reference
Number from CBPU
(if applicable)
92
PUB-BPU-CLRDP01
Attachments:
1. Detail Sanitary Plan
2. Detail of Holding Tank/STP/Retention tank (if applicable)
Arch / PE
Declaration Name Role Phone Email Firm
Reg. No
Particulars of Plumber/Contractor
Name Please select
Firm Details
Contact No
N.A
Date of Commencement Date of Completion
Attachments
93
1. Detail plan drawings of used water pumping system(s)
3. Design calculations
Select
Add Delete
94
PUB-BPU-CLRDP01
(Tick if applicable) SECTION A2: SEWERAGE WORK, RC Trench
Attachments:
1. Detail Sewerage Plan (to indicate: diameter, pipe material, gradient, manhole detail, and
longitudinal section)
2. Design & Calculation of RC Trench (if structure is proposed over sewer). PE to endorse in drawing
Arch / PE
Declaration Name Role Contact Email Firm
Reg. No
by PE (Civil): Select
I hereby certify that the
sewerage plans and the
works shown therein
comply with the provisions
of the Sewerage and
Drainage Act (Chapter
294), the Sewerage and
Drainage (Sanitary Works)
Regulations, the current
Code of Practice on the
Sewerage and Sanitary
Works.
Particulars of Plumber/Contractor
Name Please select
Firm Details
Contact No
N.A
95
PUB-BPU-CLRDP01
Attachments:
1. Detail Plan on Drainage Works as required under Section 33(3) and 33(4) of the SDA, Chapter 294
96
Appendix 4 PUB-BPU-COMPOFWORK
Instructions
Project Ref No
Project Title
Project Address
97
SECTION A1: SEWERAGE WORK
Attachments
1. Site plan and first storey plan
3. CCTV for the newly constructed sewer (applicable for sewer with
diameter 600mm or larger) to be sent to: 82 Toh Guan Road East
#C2-14, Singapore 608575
PE Name Select
PE Reg no
Role
Ph No
Firm
PE Name Select
PE Reg no
Role
Ph No
Firm
PE Name Select
PE Reg no
Role
Ph No
Firm
98
I/We, the above name, hereby certify that to the best of my knowledge and
belief, the works were carried out in accordance with the above building
plans and detailed plans, the current Code of Practice on Sewerage and
Sanitary Works, Sewerage and Drainage Act (Chapter 294) and the
Sewerage and Drainage (Sanitary Works) Regulations and any other
conditions under which the plans and amendments thereto were approved
by PUB.
Firm Name
Email address
99
Tick if applicable Application for PUB Clearance for TOP
SECTION A2: SANITARY WORK
Attachments:
2. Post Construction CCTV to the existing public sewer. To be sent to: 40 Scotts Rd #15-01,
Singapore 228231, PUB Water Reclamation (Network) Department
Firm Name
Email address
4a. Type of Submission For "New Erections", the existing buildings are unaffected. Select
Attachments:
The number of chargeable sanitary appliances in the premises upon completion of this project are
as follows:
Add Delete (Add or Delete row for house no. or unit no.)
I or my authorised
representative (with
letter of authorisation to
be provided) will be
present during PUB
(WRN)'s inspection.
After the inspection I will
submit the photographs
of the RC trench.
Attachment:
As-built plan (endorsed by PE) showing the layout and dimensions of the RC trench
and position of the existing sewer.
If Applicable
102
SECTION B: DRAINAGE WORK
Site Area: ha
Attachment:
Name Select
PE Reg No
Role
Ph No
Firm
Declaration
I hereby certify that the work has been completed in compliance with the approved drawing,
Sewerage and Drainage Act (Chapter 294), and Code of Practice for Sewerage and Sanitary Works.
Attachment:
103
Section D: Application for PUB Clearance for CSC
Attachments:
1. As constructed drainage plan (to show as built platform level, crest level
and flood protection levels)
104
Tick if applicable Application for PUB Clearance for TOP
SECTION A2: SANITARY WORK
Attachments:
2. Post Construction CCTV to the existing public sewer. To be sent to: 40 Scotts Rd #15-01,
Singapore 228231, PUB Water Reclamation (Network) Department
by PE (M/E) Select
I, being a Professional
Engineer hereby certify
that to the best of my
knowledge and belief,
the completed mechanical
and electrical (M&E) works
of the above mentioned
105
project are in accordance
with the current Code of
Practice on Sewerage and
Sanitary Works, Sewerage
and Drainage Act (Chapter
294) and other sewerage
requirements as stipulated
by Water Reclamation
(Network) Department and
have been fully and
accurately reflected in the
submitted "As built" plans.
Firm Name
Email address
4a. Type of Submission For "New Erections", the existing buildings are unaffected Select
Attachments:
The number of chargeable sanitary appliances in the premises upon completion of this project are
as follows:
Add Delete (Add or Delete row for house no. or unit no.)
106
WC Urinal Bidet Slop Sink WC Urinal Bidet Slop Sink
I or my authorised
representative (with
letter of authorisation to
be provided) will be
present during PUB
(WRN)'s inspection.
After the inspection I will
submit the photographs
of the RC trench.
Attachment:
As-built plan (endorsed by PE) showing the layout and dimensions of the RC trench
and position of the existing sewer.
107
If Applicable
SECTION B: DRAINAGE WORK
Site Area: ha
Attachment:
Name Select
PE Reg No
Role
Ph No
Firm
Declaration
I hereby certify that the work has been completed in compliance with the approved drawing,
Sewerage and Drainage Act (Chapter 294), and Code of Practice for Sewerage and Sanitary Works.
Attachment:
108
Section D: Application for PUB Clearance for CSC
Attachments:
1. As constructed drainage plan (to show as built platform level, crest level
and flood protection levels)
109
Appendix 5 ENV-CBPU-CLRTOP01-NEW SUBMISSION
APPLICATION FOR CLEARANCE OF TEMPORARY
OCCUPATION PERMIT (TOP) - NEW SUBMISSION
This form may take you 15 minutes to fill in. You will need the
following information to fill in the form:-
- Particulars of Project
- Particulars of Qualified Person
- Supporting completion and inspection certificates.
Date: 19/03/2014
To: Central Building Plan Unit
Instructions
1. This form is to be digitally signed by the Qualified Person responsible for the
project(s).
Information
1. Service Standard :
Within 7 working days.
2. For enquiries on application of status, please call 67319783 / 67319527
Particulars of Project
Project Title
Location Description
[Include Lot/Plot, MK/TS,
House No, Building
Address and Road
information]
Add Delete
Particulars of Application
Development Proposal Please Select
Application
110
Date of CBPU
19/03/2014
DC Clearance
Remarks:
Application for
Partial TOP (if applicable)
File Ref. No. /
NA Dated
Case ID
Clearance Certificate for
Building Plan on Pollution
Control; for Industrial
Plant Works (if applicable)
111
Particulars of Qualified Person
Name Please Select
Role In Project
Registration No
Firm Name
UEN
Firm Address
Telephone No.
Extension No
Fax No.
Email Address
The crest levels, platform levels, flood protection levels are in compliance
with COP on Surface Water Drainage and constructed according to
approved plans.
If there are deviations from any of the above, please indicate in detail,
attachments and PUB approval if applicable
Attachments
Dated
Certificate of Completion and Inspection for Sanitary Works
(PUB-BPU-COMPOFWORK)
113
Appendix 6 ENV-CBPU-CLRTOP01-RESUBMISSION
APPLICATION FOR CLEARANCE OF TEMPORARY
OCCUPATION PERMIT (TOP) - RESUBMISSION
This form may take you 15 minutes to fill in. You will need the
following information to fill in the form:-
- Particulars of Project
- Particulars of Qualified Person
- Supporting completion and inspection certificates.
Date: 19/03/2014
To: Central Building Plan Unit
Instructions
1. This form is to be digitally signed by the Qualified Person responsible for the
project(s).
Information
1. Service Standard :
Within 7 working days.
2. For enquiries on application of status, please call 67319783 / 67319527
Particulars of Project
Project Title
Location Description
[Include Lot/Plot, MK/TS,
House No, Building
Address and Road
information]
Add Delete
Particulars of Application
Development Proposal Please Select
Application
114
Date of CBPU
19/03/2014
DC Clearance
Remarks:
Application for
Partial TOP (if applicable)
116
Particulars of Qualified Person
Name Please Select
Role In Project
Registration No
Firm Name
UEN
Firm Address
Telephone No.
Extension No
Fax No.
Email Address
The crest levels, platform levels, flood protection levels are in compliance
with COP on Surface Water Drainage and constructed according to
approved plans.
117
Development with Public Toilet
I have inspected the public toilets in this development and that they have
been completed in accordance with the provision of sanitary facilities
stipulated in the Code of Practice on Environmental Health, except for
those provisions where waivers have been obtainted from the National
Environment Agency
Attachments
Dated
Certificate of Completion and Inspection for Sanitary Works
(PUB-BPU-COMPOFWORK)
118
Appendix 7 ENV-CBPU-CLRCSC01-NEW SUBMISSION
Date: 19/03/2014
To: Central Building Plan Unit
National Environment Agency
40, Scotts Road #13-00
Environment Building
Singapore 228231
Instructions
1. This form is to be digitally signed by the Qualified Person responsible for the
project(s).
Information
1. Service Standard : Within 7 working days.
2. For enquiries on application of status, please call 67319783 / 67319527
Particulars of Project
Project Reference Number
Project Title
Location Description
[Include Lot/Plot, MK/TS,
House No, Building
Address and Road
information]
Add Delete
Particulars of Application
Development Proposal Please Select
119
Application
Date of CBPU
DC Clearance
120
Particulars of Application (Continue)
Role In Project
Registration No
Firm Name
UEN
Firm Address
Telephone No.
Extension No
Fax No.
Email Address
Declaration by Qualified Person
I confirm that:
The works have been carried out and completed. For industrial plant works,
all related pollution control equipment and facilities have been installed/
completed according to the approved plans as listed in Particulars of Project
and Application
121
Confirmation
1) I confirm that:
a) there are no roof gutters (including rain water down pipes and
outlets, and roof supper drains) provided for in the development
proposal; or
b) waiver for roof gutter has been obtained from the National Environment
Agency in writing on : File Ref No:
Date:
c) There are roof gutters (including rain water down pipes and outlets,
and roof scupper drains) provided in the development proposal. Waiver
application from ENV-CBPU-WVRG is attached.
d) Confirmation for a), b) or c) not applicable, for A&A and reconstruction
building projects.
Attachments
Dated
1. Certificate of Completion and Inspection for Building
Plan for Environmental Health
122
Attachments (Continue)
123
Appendix 8 ENV-CBPU-CLRCSC01-RESUBMISSION
Date: 19/03/2014
To: Central Building Plan Unit
National Environment Agency
40, Scotts Road #13-00
Environment Building
Singapore 228231
Instructions
1. This form is to be digitally signed by the Qualified Person responsible for the
project(s).
Information
1. Service Standard : Within 7 working days.
2. For enquiries on application of status, please call 67319783 / 67319527
Particulars of Project
Project Reference Number
Project Title
Location Description
[Include Lot/Plot, MK/TS,
House No, Building
Address and Road
information]
Add Delete
Particulars of Application
Development Proposal Please Select
124
Application
Date of CBPU
DC Clearance
125
Particulars of Application (Continue)
Role In Project
Registration No
Firm Name
UEN
Firm Address
Telephone No.
Extension No
Fax No.
Email Address
Declaration by Qualified Person
I confirm that:
The works have been carried out and completed. For industrial plant works,
all related pollution control equipment and facilities have been installed/
completed according to the approved plans as listed in Particulars of Project
and Application
126
Confirmation
1) I confirm that:
a) there are no roof gutters (including rain water down pipes and
outlets, and roof supper drains) provided for in the development
proposal; or
b) waiver for roof gutter has been obtained from the National Environment
Agency in writing on : File Ref No:
Date:
c) There are roof gutters (including rain water down pipes and outlets,
and roof scupper drains) provided in the development proposal. Waiver
application from ENV-CBPU-WVRG is attached.
d) Confirmation for a), b) or c) not applicable, for A&A and reconstruction
building projects.
Attachments
Dated
1. Certificate of Completion and Inspection for Building
Plan for Environmental Health
127
Attachments (Continue)
128
Appendix 9 PUBWTR-0-MCG01
Instructions
Nature of
manufacturing products
Please submit a copy of the water balance chart indicating the quantity of water
required at each manufacturing process. See Annex A.
Percentage of water %
recycling (See Annex B)
No of occupants
No of staff that
take shower
Showering m³/mth
Cooling Usage
PUB Water NEWater
No of cooling tower
129
Refrigerating capacity
and operating hours
of individual cooling
towers:
Tons hr/mth
Add Delete
Other Usage
PUB Water NEWater
No of toilets
Add Delete
Total 0 m³/mth 0 m³/mth
Add Delete
130
Appendix 10 PUBWTR-0-NMC01
Project Description
No of occupants
No of occupants
that take shower
Showering (m3/mth)
Cooling usage
PUB Water NEWater
No of cooling towers
Refrigerating capacity
and operating hours of
individual cooling towers:
Tons hr/mth
Add Delete
Other usage
PUB Water NEWater
131
No of toilets
Add Delete
Total 0 (m3/mth) 0 (m3/mth)
(m3/mth)
Add Delete
132
PUBWTR-0-RCG01 Appendix 11
No of Units
Common Amenities
m³/mth m³/mth
Add Delete
Other usage
(Please specify)
m³/mth m³/mth
Add Delete
m³/mth
Add Delete
133
Appendix 12 PUBWTR-0-TSP01
Instructions
1. This form is to be digitally signed by the Licensed Water Service Plumber/
Professional Engineer.
Details of PUB Water / NEWater requirement
Showering (m3/mth)
Washing use
(m3/mth) (m3/mth)
Add Delete
Total 0 (m3/mth) 0 (m3/mth)
134
(m3/mth) (m3/mth)
Add Delete
Total 0 (m3/mth) 0 (m3/mth)
135
(Continue)
Workers dormitory
(m3/mth)
Add Delete
Type of Project
Started from
136
Appendix 13 PUBWTR-0-PPC01
PRE-PLANNING CONSULTATION
Date: 24/02/2014
To: PUB Water
Water Supply (Network) Department
Public Utilities Board
40 Scotts Road #22-01
Environment Building
Singapore 228231
Instructions
1. This form is to be digitally signed by the Qualified Person.
2. Design of water service installation including the mode of supply shall comply
with the Public Utilities (Water Supply) Regulations and the Singapore
Standard CP 48 - Code of Practice for Water Services.
3. Water meter shall be located above ground near to the main entrance of the
above development and shall be easily accessible for maintenance and
reading.
5. Potable water storage cisterms should not be located below sanitary pipes
and other non-potable water pipes.
Location Description
[Include Lot/lot, MK/TS,
Address/Road and
Building Name if any]
Project Description
Estimated NEWater
Requirement (m³/mth)
137
Platform Level of
Development (mRL)
138
Particulars of the Qualified Person
Name Please Select
Name of Company
UEN
Submission Checklists
1 Site Plan
139
Appendix 14 PUBWTR-0-WLP01
Project Description
Location Description
[Include Lot/lot, MK/TS,
Address/Road
and Building Name if any]
NEWater (m3/mth)
Commencement Date
Platform Level of
Development (mRL)
Name of Company
140
UEN
Address
Telephone No.
Extension No.
Fax No.
Residential Address
141
Particulars of Licensed Water Service Plumber (Continue)
Mailing Address
(if different from above)
Extension No.
Fax No.
Pager No.
Handphone No.
Licence No.
I/C No.
Declaration by Licensed Water Service Plumber
1 I, , the undersigned, hereby certify
that the water service installation at the premises is designed in
full compliance with the Public Utilities Board's requirements
including the Public Utilities (Water Supply) Regulations,
Singapore Standard CP 48 - Code of Practice for Water
Services, Authorities' requirements and other statutory
requirements. I also confirm that potable water storage cisterns
shall not be located below sanitary pipes and other non-potable
water pipes. All the water fittings installed in the water service
installation are of types that comply with standards prescribed/
stipulated by PUB and all water conservation measures will
be adopted.
2 The site plan, the water schematic drawing/s and the breakdown
of water requirements, if any, of the above developments are
attached herewith.
Submission Checklists
1 Site Plan
142
Appendix 15 PUBWTR-0-WSW01
3. Please note that for "Particulars of Licensed Water Service Plumber", the
member role of "Licensed Water Service Plumber" is required when updating
the member's details.
Particulars of Project
Pre-Planning Consultation Yes
No
Date of Pre-Planning
Consultation with PUB
Location Description
[Include Lot/lot, MK/TS,
Address/Road
and Building Name if any]
Project Description
143
Estimated Water Requirement
PUB Water (m3/mth)
NEWater (m3/mth)
Commencement Date
Name of Company
UEN
Address
144
Particulars of the Professional Engineer (Continue)
Telephone No.
Extension No.
Fax No.
Particulars of the Owner/Developer
Name Please Select
Name of Company
UEN
Address
Telephone No.
Extension No.
Fax No.
Particulars of the Licensed Water Service Plumber
Name Please Select
Address
Telephone No.
Extension No.
Fax No.
Declaration by Professional Engineer
1 I, , the Professional Engineer-in-charge
hereby certify that the water service installation is designed in full
compliance with the Public Utilities Board's requirements including
the Public Utilities (Water Supply) Regulations, Singapore Standard
CP 48 - Code of Practice for Water Services, Authorities'
requirements and other statutory requirements. I also confirm that
potable water storage cisterns shall not be located below sanitary
pipes and other non-potable water pipes. All the water fittings
installed in the water service installation are of types that comply
with standards prescribed/stipulated by PUB and all water
conservation measures will be adopted.
2 The site plan, the water schematic drawing/s and the breakdown of
water requirements, if any, of the above developments are attached
herewith.
Submission Checklists
1 Site Plan
145
2 Water Reticulation Schematic Drawing
146
Appendix 16 PUBWTR-0-CSC01
Particulars of Project
Project Reference Number
Project Description
Development Address
Commencement Date
Name of Company
UEN
Telephone No.
Extension No.
Fax No.
147
Declaration by Professional Engineer
1 I, the Professional Engineer-in-charge
hereby certify that I have supervised the construction of the water
service installation of the above development and inspected the
completed water service installation. I confirm that to the best of my
knowledge and belief, the water service installation was carried out in
accordance with the Public Utilities Board's requirements including the
Public Utilities (Water Supply) regulations, Singapore Standard CP
48-Code of Practice for Water Services, Authorities' requirements and
other statutory requirements. I also confirm that potable water storage
cisterns have not been located below sanitary pipes and other
non-potable water pipes. All the water fittings installed in the water
service installation are of the types that comply with standards
prescribed / stipulated by PUB and all water conservation measures
have been adopted. I further certify that the said water service
installation and the associated electrical devices and equipment have
been tested and are safe and acceptable for operation.
148
Appendix 17 – Guideline on Corenet Form Submissions
DC plan without DP
QP [Registered Architect / PE(Mechanical or Civil)]
Section A2: Sewerage QP [Registered Architect / PE (Mechanical or Civil)] except where
Work, RC Trench the work is required to be endorsed by a PE (Civil) under BCA’s
Building Control Act/Regulations.
Section B: Drainage Without DP
Work QP [Registered Architect]
With DP
QP [PE (Civil)]
Section C: Infrastructure QP [PE(Civil)]
Work
149
Form Name Details Sections Who can submit?
PUB-BPU-CLRDP01 – Submission for DP Development involving used water pumping system and/or deep
Section A1: Sanitary excavation/trenching for sanitary drainline/sewer connection
Work works:
QP [Registered Architect / PE (Mechanical or Civil)]except:
(a) Used water pumping systems shall be prepared and signed by
PE (Mechanical).
(b) where the works is required to be endorsed by a PE(Civil) under
BCA’s Building Control Act/Regulations.
149
Form Name Details Sections Who can submit?
Form B – – Development Projects via e-Corenet)
QP [Registered Architect or PE (Mechanical or Civil)] except where
the excavation/trenching/structure works is required to be
endorsed by a PE (Civil) under BCA’s Building Control
Act/Regulations.
149
Form Name Details Sections Who can submit?
PUB-BPU-COMPOFWORK Option 3 Section D: Application QP [Registered Architect or PE (Mechanical or Civil)] who has
Application for PUB Clearance for PUB Clearance for submitted the DP for the respective works.
for CSC CSC This section is for SEW clearance only.
(For project which has earlier
obtained clearance for TOP) For Drainage clearance, please use Certificate of Inspection for
Drainage Works form (PUB-DD-CSIDRA) which is to be submitted
by PE (Civil).
PUB-BPU-COMPOFWORK Option 4 Section A1: Sewerage Please refer to Option 2 and Option 3
Application for PUB Clearance Work
for both TOP & CSC Section A2: Sanitary
(All other projects) Work
Section A3: RC Trench
Completion
Section B: Drainage
Work
Section C: Infrastructure
Work
Section D: Application
for PUB Clearance for
CSC
149
Appendix 18 – Contact List
For further enquiries on Corenet form changes, please contact PUB BPU at:
Hotline: 67313512
Email: PUB_BPU@pub.gov.sg
153