Professional Documents
Culture Documents
Edge Alkaline UM
Edge Alkaline UM
Edge Alkaline UM
with
Stainless Steel
RO | UV
EDGE
Tips for Safety and Maintenance of Your Aquaguard® Select EDGE with Stainless Steel.................................. 8
Important Suggestions.......................................................................................................................................... 9
Aquaguard® Select EDGE RO+UV+MTDS with Stainless Steel Purification Process...................................... 10
Aquaguard® Select EDGE UV with Stainless Steel Purification Process........................................................... 11
Technical Specifications* of Aquaguard Select EDGE RO+UV+MTDS with Stainless Steel.............................
®
12
Technical Specifications* of Aquaguard Select EDGE with UV with Stainless Steel.......................................... 13
®
**BIOTRON™ TECHNOLOGY
The Biotron is a patented (applied) Multiple Magnetic Field (MMF) generating device. It creates a
magnetic field in the water. This magnetic field breaks complex water molecules into fine micro-clusters,
making water more bio-available, so that your body can easily absorb the minerals and the goodness of
water, along with its much needed nutrients.
**a) Independent Published Scientific Research
b) Agriculture Water Management 96(2009) 1229-1236
c) Current World Environment Vol. 9(3), 1008-1016 (2014)
d) Nutrition Research and Practice (Nutr Res Pract) 2013; 7(1):34-42
Make sure that your Aquaguard® Select EDGE with Stainless Steel is installed by a trained
Eureka Forbes Service Technician only.
#
As per standard test conditions.
** As per UV manufacturer’s specifications.
HERE’S HOW YOUR AQUAGUARD® SELECT EDGE
RO+UV+MTDS WITH STAINLESS STEEL WORKS
DRAIN
FLOW RESTRICTOR
REGULAR
WATER
TANK
WATER TAP
CARTRIDGE
SOLENOID
BIOTRON
VALVE
RO MEMBRANE
CHEMI BLOCK
INLET
HD - FILTER
E-BOILING
QG TUBE
MINERAL GUARD
DIVERTER
VALVE
DRY RUN
SENSOR
ZERO PRESSURE
PUMP
FLOW RESTRICTOR
TDS MODULATOR
COPPER MAXX
CARTRIDGE
ACTIVE
Membrane life enhancer is
NOTE : THIS IS A SCHEMATIC ILLUSTRATION OF THE PRODUCT TO GIVE A VISUAL SCHEME OF WORKING OF PRODUCTS. recommended to be installed
if the TDS is above 1000 ppm or
THIS IS NOT AN ACTUAL ENGINEERING DRAWING OF THE PRODUCT. hardness above 300 ppm
HERE’S HOW YOUR AQUAGUARD® SELECT EDGE
WITH UV WITH STAINLESS STEEL WORKS
PURIFIED
WATER
TANK
LPS
NRV
12 V SOLENOID
VALVE
CARTRIDGE
BIOTRON
(WITH BUILT-IN PARTICLE TRAP FILTER)
CHEMI BLOCK
HD - FILTER
E-BOILING
QG TUBE
RAW WATER
INLET
MINERAL GUARD
COPPER MAXX
CARTRIDGE
ACTIVE
DIVERTER
VALVE
FLOW RESTRICTOR
NOTE : THIS IS A SCHEMATIC ILLUSTRATION OF THE PRODUCT TO GIVE A VISUAL SCHEME OF WORKING OF PRODUCTS.
THIS IS NOT AN ACTUAL ENGINEERING DRAWING OF THE PRODUCT.
TIPS FOR SAFTY AND MAINTENANCE OF YOUR
AQUAGUARD® SELECT EDGE WITH STAINLESS STEEL
1. Read attentively and understand the purifier and its functions before use.
2. Installation and service has to be conducted by authorised persons from Eureka Forbes Limited only.
3. Install the purifier at a location with ample ventilation.
4. Ensure that the purifier is installed in a dry place. Do not expose it to direct sunlight or heat sources.
5. Ensure that the installation height is ideal for comfortable reach for the user to avoid any accidental
water spill (Approx. 5 feet).
6. Do not remove or insert the plug with wet hands.
7. Replace the filters when the end of life indicator is displayed by your purifier.
8. Ensure that the filter cartridges and spares used during service/replacement are genuine and from
Eureka Forbes only.
9. Always switch off and disconnect the power plug before maintenance or cleaning.
10. In case of any damage or incorrect functioning, immediately contact an authorised service centre of
Eureka Forbes Limited. Do not repair on your own.
IMPORTANT SUGGESTIONS
DO’s
®
• Turn OFF the main switch if you do not plan to use your Aquaguard Select for more than 3-4 hours.
®
• Store water from your Aquaguard Select in clean containers. For hygienic reasons, it is preferable not to store
water for more than 2 days.
®
• We recommend routine check-ups of your Aquaguard Select at least once in 6 months.
®
• If your Aquaguard Select has not been used for a long time, allow 2-3 glasses of water to flow out before
collecting the water for use.
DONT’s
• Spill water on any panel as this may lead to shock.
®
• Store water from your Aquaguard Select in matkas and candle filters, as the water can get re-contaminated.
®
• Connect ordinary pipes or tubing to the outlet spout to collect water from your Aquaguard Select .
• Use an extension box for power connection.
• Connect it to a hot water supply source.
®
• Install your Aquaguard Select close to a gas stove or cooking range.
• Cover the product with plastic or cloth. Putting a cover on the product may cause damage to the product.
AQUAGUARD® SELECT EDGE RO+UV+MTDS WITH
STAINLESS STEEL PURIFICATION PROCESS
FOR AQUAGUARD® SELECT EDGE RO+UV+MTDS WITH STAINLESS STEEL
1. HD Filter CartridgeTM High Density Multiple Layer Polypropylene Removes turbidity and other fine suspended particles such as dust, dirt, mud and
sand, giving you clear water.
2. Chemi Block (with build Dust-free Bacteriostatic Activated Carton Reduces excess chlorine and organic impurities. Also adsorbs bad taste and odour
in Particle Trap Filter) Block from the water.
3. Mineral GuardTM Microcontroller based electronic impulse Generates electronic impulses which prevent scaling/deposition of Calcium and
producer Magnesium on the Quartz Glass tube of the UV reflector chamber, thereby, ensuring
best UV Penetration through Quartz Glass into the water column and at the same
time keeping essential minerals like Calcium and Magnesium intact in water.
4. Membrane Life Special anti-scalant media Prevents scaling of dissolved salts on the surface of the membrane, thereby,
Enhancer*** enhancing the membrane life and performance.
5. HD RO Cartridge Thin Film Composite (TFC) Reverse Reduces TDS, Hardness, Pesticides and heavy metals like arsenic, lead and mercury.
Osmosis Membrane Eliminates micro-organisms like bacteria, viruses, protozoa and cysts.
6. UV e-boiling Germicidal UV Lamp UV disinfects the water by eliminating waterborne disease-causing bacteria, viruses
and protozoa, thereby, making it safe to drink.
7. Active Copper MaxxTM A unique combination of naturally occurring Enhances the taste of the water and increases the level of essential minerals which
Cartridge vital minerals like Calcium, Magnesium, helps in improved health and body functions. At the same time, balancing the pH of
Copper, and Zinc with anti-microbial carbon water, making it healthy.
granules.
8. BiotronTM Cartridge Patented Multiple Magnetic Field (MMF) Breaks complex water molecules into fine micro- clusters, making water more
generating device bio-permeable, so that your body can easily absorb the goodness of water, along
with its much needed nutrients.
***Not a part of the product, Membrane life enhancer is recommended if the input water TDS is more than 1,000 ppm (mg/L) or input water hardness is more than 300 ppm (mg/L).
Available at extra cost.
AQUAGUARD® SELECT EDGE UV WITH STAINLESS
STEEL PURIFICATION PROCESS
FOR AQUAGUARD SELECT EDGE UV WITH STAINLESS STEEL
®
1. HD Filter CartridgeTM High Density Multiple Layer Polypropylene Removes turbidity and other fine suspended particles such as dust, dirt, mud and
sand, giving you clear water.
2. Chemi Block (with build Dust-free Bacteriostatic Activated Carton Reduces excess chlorine and organic impurities. Also adsorbs bad taste and odour
in Particle Trap Filter) Block from the water.
3. Mineral GuardTM Micro-controller based electronic impulse Generates electronic impulses which prevent scaling/deposition of Calcium and
producer Magnesium on the Quartz Glass tube of the UV reflector chamber, thereby, ensuring
best UV Penetration through Quartz Glass into the water column and at the same
time keeping essential minerals like Calcium and Magnesium intact in water.
4. UV e-boiling Germicidal UV Lamp UV disinfects the water by eliminating waterborne disease-causing bacteria, viruses
and protozoa, thereby, making it safe to drink.
5. Active Copper MaxxTM A unique combination of naturally occurring Enhances the taste of the water and increases the level of essential minerals which
Cartridge vital minerals like Calcium, Magnesium, helps in improved health and body functions. At the same time, balancing the pH of
Copper, and Zinc with anti-microbial carbon water, making it healthy.
granules.
6. BiotronTM Cartridge Patented Multiple Magnetic Field (MMF) Breaks complex water molecules into fine micro- clusters, making water more
generating device bio-permeable, so that your body can easily absorb the goodness of water, along
with its much needed nutrients.
TECHNICAL SPECIFICATIONS* OF AQUAGUARD® SELECT
EDGE RO+UV+MTDS WITH STAINLESS STEEL
01 Turn off the power supply and 02 Open the water dispenser tap and 03 Open the front fascia.
close the water supply before empty the water from regular water
proceeding to change the cartridge. tank and Ayur water tank.
OFF RO UV
ON EDGE
04 Lift the tap upward. 05 Lift the cartridge upwards and 06 Match the label and the colour
pull it towards the front using two code with the filter to be replaced.
hands.
RO UV
FILTER
FILTER
FILTER
FILTER
FILTER
FILTER
FILTER
Important Note: To avoid confusion, do not remove all the filters at once. Remove, match and change the filters one by one.
07 Unclip the junction connector. 08 Rotate Filter clockwise to 09 Replace the new filter by first
eject. aligning its position to the top
manifold using the arrow guides.
FILTER
FILTER
Grip the cartridge firmly from
10 the bottom, apply an upward force
11 Carefully match and re-clip the 12 Pull the levers on either side of
colour-coded junction connectors. the filters upwards to bring the
and rotate anti-clockwise till it fits
cartridge to its original position.
completely.
RO UV
FILTER
FILTER
FILTER
FILTER
FILTER
13 Push down levers once cartridge 14 Push down the taps back to their 15 Fix the front fascia and turn on
is back to its position. default position. the power supply and water supply.
RO UV
RO UV
FILTER
FILTER
FILTER
FILTER
EDGE
KNOW YOUR AQUAGUARD® SELECT EDGE RO+UV+MTDS
WITH STAINLESS STEEL NEXT-GEN LED DISPLAY
Indication Bar
PURIFICATION PROCESS PROCESS RO/UV ICON CALL SERVICE POWER ICON INDICATION BAR
Power ON All LEDs will glow for 5 seconds
Purification Process Blinks for 6 secs. UV icon Solid OFF ON Blue Solid
Tank Filling Mode Blinks at 0.5 secs. rate RO & UV icon Solid OFF ON Blue Solid
Tank Full Solid OFF OFF ON Blue Solid
UV Lamp/SV/Pump Fault OFF OFF Blinks at 0.5 secs. ON Blue Solid
DRS OFF OFF OFF OFF Blue Light Blinks
EA Fault OFF OFF Red Solid ON Blue Light Blinks
Filter Life 1st Warning (5,400 litres) Blinks every 5 secs. OFF Blinks every 5 secs. ON ON
Filter Life 2nd Warning (5,700 litres) Blinks every 2 secs. OFF Blinks every 2 secs. ON ON
Filter Life EOL (6,000 litres) Blinks every 0.5 secs. OFF Blinks every 0.5 secs. ON ON
KNOW YOUR AQUAGUARD® SELECT EDGE UV
WITH STAINLESS STEEL NEXT-GEN LED DISPLAY.
Power Icon
Indication Bar
PURIFICATION PROCESS PROCESS CALL SERVICE POWER ON INDICATION BAR
Power ON All LEDs will glow for 5 seconds
Purification Process Blinks for 30 secs. OFF ON Blue Solid
Tank Filling Mode Blinks at 0.5 secs. rate OFF ON Blue Solid
Tank Full Solid OFF ON Blue Solid
UV Lamp/SV Fault OFF Blinks at 0.5 secs ON Blue Solid
LPS OFF OFF OFF Blue Light Blinks @ 0.5 Secs
EA Fault OFF Red Solid ON Blue Light Blinks @ 0.5 Secs
Filter Life 1st Warning (5,400 litres) Blinks every 5 secs. Blinks every 5 secs. ON ON
Filter Life 2nd Warning (5,700 litres) Blinks every 2 secs. Blinks every 2 secs. ON ON
Filter Life EOL (6,000 litres) Blinks every 0.5 secs. Blinks every 0.5 secs. ON ON
MAINTAINING YOUR AQUAGUARD® SELECT EDGE
WITH STAINLESS STEEL
1. Discard the first filling of water from the storage tank.
2. Drain the water from the tank if it hasn’t been used for over 48 hours.
3. Ensure that the flow restrictor is checked and replaced (if required) by the authorised service technician
during the mandatory service or in-service call.
A QUICK CHECKLIST
Less water has been 1. Is the tap water valve closed? Open the tap water valve.
purified 2. Is the tap water pressure too low? If so, the amount of purified water will be reduced.
3. Filters may be clogged or damaged? Call an authorised Eureka Forbes service technician.
Water dosen’t flow into 1. Is there water available in the overhead tank? Ensure the overhead tank is filled with water.
the storage tank 2. Is the main water supply tap closed? Ensure the tap is open.
3. Not sure what is wrong? Call an authorised Eureka Forbes service technician.
Water is leaking 1. Is water coming out of the tap of the purifier? Close the tap water valve, unplug the power cord and call an
authorised Eureka Forbes service technician.
CLEANING AND DISINFECTION OF WATER STORAGE TANKS
Note: Storage tank of this product must be periodically (at least once in every 30 days) cleaned by a
disinfectant. Disinfection Tablets may be purchased from the company authorised Service Centre. Please
follow the disinfection process strictly as per the instructions as provided in this User Manual.
Your Aquaguard® Select is equipped with a unique pump which has both suction and boosting capabilities, and comes
with specifically designed DRS (Dry Run Sensor). Now, this enables your Aquaguard® Select to work in the following
operating conditions:
• Normal Input Water Pressure – up to 3 bar (max.)
• Low Water Pressure from Loft Tank
• Zero Water Pressure
• Suction Mode: Maximum 3 feet below product level
Product Functioning at ‘Normal/Low and Zero Water Pressure’:
• Ensure that the water flow from the tap into the product is always more than 1.5 LPM.
• In case there is no incoming water supply, the DRS detects unavailability of water and stops the unit from working to
prevent dry running.
• As and when the water supply resumes, the DRS detects the availability of water and restarts the product. Meanwhile, the
intelligent mechanism in your Aquauard® Select will keep on checking the availability of water at regular defined intervals
and makes the product work when water supply resumes.
Note: In case you notice that water in the supply line resumes and product is in standby mode, then please restart the product
by switching the power supply OFF and ON again.
Product Functioning with ‘Suction Capability’:
• The ZPP in your Aquauard® Select also has the capability of suction of water from a 3 feet distance below the level of product i.e. it can pull water from a
bucket/container.
• Note: Water suction from underground storage tank, pump, open well, etc. where the water level is beyond 3 feet below the level of product is not
suitable.
• Whenever the water in the container/bucket is emptied, the DRS detects non-availability of water and stops the product from functioning.
• Note: When the container/bucket is refilled with water, the product should be restarted by switching the power supply OFF and ON again.
• Prolonged use in loft tank mode /suction mode can impact the working of pump, performance of product and life of filters. If the performance is not
meeting the expectation of the consumer due to low pressure, then use of a booster pump is recommended.
• Do not re-circulate/reuse the rejected water (discharged by the product) back into the product.
WARRANTY TERMS AND CONDITIONS
1. The Products are warranted against manufacturing defects for a period of twelve (12) months from the date of original
purchase.
2. The Customer will notify the Company in writing promptly of any defects noticed and give the Company or its authorized
agent adequate opportunity to inspect test and remedy them for which the Customer will deposit the goods at its own
expense, if so, required by the Company with the Company's Office/Service Centre along with the original invoice in the city
where they are sold.
3.The Inspection and Test Report of the company's office/service centre will be final and binding under the warranty for
determining defects, repairs / alterations required or carried out or certifying work of the goods thereafter.
®
4. Aquaguard may require initial setting, post-installation, depending on varying water conditions and power supply. In case of
any service requirement, post-installation, please contact the company's service centre.
5. The company or its authorized agent will be entitled to retain any defective part replaced under the warranty.
6. Notwithstanding anything to the contrary contained or implied by this warranty:
a) The company's liability under this warranty shall be limited to the first sale of the goods by the company to the customer and
will not apply or extend to any secondary sale of goods by the customer.
b) The company's liability under this warranty shall be limited only to defects in the goods which occur under the conditions of
normal operation of the goods and their proper and prescribed use. The warranty does not cover or extend to defects which are
determined by the company or its authorized agents as occurring or resulting from or attributable to negligence, abuse, misuse,
faulty care, operation or maintenance or repairs, alterations to the goods or any part thereof by others or the use of the goods
on electrical supply for which they are not designed, or damage caused by lightening or other electrical disturbances or interrup
tions, dismantling or re-installation at a different location.
c) The company's liability under this warranty shall remain valid only if the goods are duly installed by the company or its
authorized agency at the location specified in the invoice and such installation is undertaken by the company or its authorized
agent or franchisee.
d) Consumable items mentioned in the consumables table are subject to normal wear and tear are not covered by this warranty.
Please refer model specific components given in the user manual under the table ‘consumable cartridges’.
WARRANTY TERMS AND CONDITIONS
e) Reverse Osmosis Membrane warranty is for a period of 1 year (or) 6,000 litres (whichever is earlier) from the date of installa
tion, on the condition that the input water is as per the standard test conditions for RO variants (provided in the section
‘Technical specifications table’), mentioned in the user manual. If the RO membrane gets clogged within warranty period, it
will be cleaned/repaired/replaced free of charge as deemed fit by the company authorized service person/centre after inspec
tion. (At applicable for RO models only.)
f) The customer will have no claim against the company, its employees and its authorized agents or franchisees under or
pursuant to this warranty in respect of death or injury to the customer or any other person or loss or damage to any property
caused by or due to equipment failure, breakdown or accident, fire or operation or utilization of the goods otherwise than in
accordance with the user manual or by due to any other cause or circumstances beyond the control of the company.
g) The company's liability, under this warranty, shall in no event and under no circumstances exceed the price paid by the
customer to the company for the goods stated in the invoice.
General
For the purpose of this warranty, the following expressions shall have the following meanings respectively:
1. The 'Goods' shall mean the goods described in the Order Form.
2. The 'Customer' shall mean the original purchaser of goods from the company.
3. The 'Company' shall mean EUREKA FORBES LIMITED.
® ® ® ®
4. Aquaguard means and includes Aquaguard , Aquaguard Select and Sure from Aquaguard .
5. 'General Terms & Conditions' shall mean the terms and conditions agreed upon by the customer and the company printed on
the Order Form.
6. 'Invoice' shall mean the invoice issued by the company to the customer describing the goods and indicating, inter alia, the
total purchase price thereof and name of the customer.
7. 'User Manual shall mean the instructions for Installation, use and maintenance provided through QR code along with Product
supplied by the company.
8. EFL reserves the right, in its absolute discretion, to change, alter or discontinue and alter the terms and conditions from time
to time without any prior notice.
9. Any disputes are subject to Mumbai Jurisdiction only.
WARRANTY TERMS AND CONDITIONS
Post-warranty
1. The customer may be offered a yearly Service Contract at the prevailing company rates and terms.
2. In case the customer does not wish to enter the Service Contract, he has the option of calling the company's service centre
having his Aquaguard® services on an actual basis, i.e., by paying the labour cost and spares needed to attend to that
service/complaint call at the prevailing company rates. Such service will be rendered by the company in towns/places where the
company has its service centres.
3. If during such servicing it is necessary for the company to replace or repair defective components or parts, the customer shall
be required to pay for the same as per the company's prevailing price list.
4. Eureka Forbes limited reserves the right to offer annual maintenance contract/ensure availability of spares only up to 7 years
from the date of invoice.
*Conditions apply.
deepa.customercare@eurekaforbes.com
Aquaguard® Select
disposing
Aquaguard® Select
AGUM_Col_V3
authorised
R00-0122
is the new brand identity of . The brand names Dr. Aquaguard and Aquaguard® Select along with their logos and Product name are original product from the
house of Eureka Forbes Limited.