Professional Documents
Culture Documents
28-29052022-Pull Off Test (Trial) - Pemb. Dermaga Terminal LPG Presurized Kupang (Piping) - PQT-Pertamina PN-NK-AMM-AKD
28-29052022-Pull Off Test (Trial) - Pemb. Dermaga Terminal LPG Presurized Kupang (Piping) - PQT-Pertamina PN-NK-AMM-AKD
01-ATR-PERT-NK-
Date: 29 May 2022 Report No:
AMM-2022
Coating System:
Average
Ave. DFT Temperature
(10 Readings) Time Cured During Cure
Date Coating
Coating Before
Product Name Applied to µm mils °C °F
Sequence Overcoating
Substrate
(H:M)
Intermediate
Penguard HB grey n/a n/a N/A
1
Intermediate Futura Classic
n/a N/A N/A
2 9003/3020
Futura Classic
Topcoat n/a n/a N/A
9003/3020
Page 1 of 7
Jotun Performance Coatings Inspection Form I Adhesion Pull Off Rev 3 January 2016
Jotun Adhesion Test Report
Pull-Off Test Method
Lightly
Abrade & Cut around Number of Load Pull
Ambient
Test Clean the the dolly Adhesion Rate and
surface Conditions
Standard before Tests per Maximum
before fixing During Test
testing? Sample Pull Time
dolly?
Apply a tensile
stress,
Yes, all increasing at a
6, calculate Carry out test
thickness at 23°C ±2°C rate not
the average of
ISO 4624: unless the 6 tests and at 50% ± greater than 1
Yes.
2003 otherwise and record as 5% RH or as MPa/second
specified or the result agreed. and complete
agreed the test within
90 seconds.
Follows ISO
4624 but
NORSOK specifies an
Follows ISO automatic Follows ISO Follows ISO Follows ISO
M-501 Rev
4624 4624 4624 4624
6 pulling device
with centred
pulling force
Generally No.
Only sand or 3 per test site.
clean the Report can be Apply a tensile
No as per the stress less
surface in a for individual
standard. If than 150 psi /
manner that test, omit
agreed, then second (1
will not affect lowest and
ASTM D cutting must MPa/ Second )
integrity of the highest and Not specified
4541 be reported as and complete
coating or average the
a variation to the test in less
leave a remainder or
the standard than 100
residue. Only average all as
test. seconds.
sand with 400 specified or as
grit abrasive agreed.
paper or finer.
Page 2 of 7
Jotun Performance Coatings Inspection Form I Adhesion Pull Off Rev 3 January 2016
Jotun Adhesion Test Report
Pull-Off Test Method
Result of Test:
DFT Was
Before DFT After cutting tool Result
Abrasion Abrasion used? Failure
Test Date Dolly Date Dolly Mode as
No Microns Mic Placed Pulled MPa psi per chart
ron Yes No below
s
May 28,
1 284 May 29, 2022 Yes 11.00
2022
May 28,
2 270 May 29, 2022 Yes 5.27
2022
3
6
Average MPa/psi
3 Samples 8.13
Page 3 of 7
Jotun Performance Coatings Inspection Form I Adhesion Pull Off Rev 3 January 2016
Jotun Adhesion Test Report
Pull-Off Test Method
C = 2nd coat
B = Cohesive failure of 1st coat
B = 1st coat
A/B = Adhesive failure between
substrate and first coat
Page 4 of 7
Jotun Performance Coatings Inspection Form I Adhesion Pull Off Rev 3 January 2016
Jotun Adhesion Test Report
Pull-Off Test Method
Dolly #1
70 % Cohesion C
30 % Cohesion B
Dolly #2
60 % Cohesion B
25 % Adhesion B/C
15 % Cohesion D
Page 5 of 7
Jotun Performance Coatings Inspection Form I Adhesion Pull Off Rev 3 January 2016
Jotun Adhesion Test Report
Pull-Off Test Method
Jotun CA Notes:
This Pull Off test carried out for trial to find out adhesion value of paint on mock-up (pipe) that have
conducted by applicator self as per actual treatment and application on field.
Average value Pull-Off test is 8.13 MPa from two points & more than minimum requirement
3.00 MPa
Manufacturer Rep.
Contractor Rep.
Client Rep.
Page 6 of 7
Jotun Performance Coatings Inspection Form I Adhesion Pull Off Rev 3 January 2016
Jotun Adhesion Test Report
Pull-Off Test Method
PHOTOGRAPH REPORT
Install dolly in progress and it result Cut around the dolly was done
Pull-Off test on progress and start from zero 0.00 Mpa Dolly 1 reading 11.00 MPa
Dolly 1 reading 11.00 MPa Average Pull-Off result 8.13 MPa and witnessed by all parties
Page 7 of 7
Jotun Performance Coatings Inspection Form I Adhesion Pull Off Rev 3 January 2016