Professional Documents
Culture Documents
Electrolux PLD4375RFC3 Dishwasher Installation
Electrolux PLD4375RFC3 Dishwasher Installation
• "Y" Branch Tailpiece and Plumbing Supply Store Observe all local codes and ordinances for
2. Note the locations of electrical supply and dishwasher's
Connector Kit (See Step 4) electrical and plumbing connections. All electrical electrical junction box on right underside of unit behind kickplate
• Air Gap Kit (See Step 4) Plumbing Supply Store and plumbing work should be performed by assembly. See Figure 3.
• Fasteners for floor Hardware Store qualified persons. Failure to follow this warning
3. Cut access hole in shaded area shown in Figure 2.
anchoring (See Step 9) could result in death or serious injury.
4. Pull electrical cable through hole into installation area.
1. Make sure your location has the right drain, water, and Water
electrical outlets to make the connections. Do not install unit
1. Determine where you will connect to hot water supply. Review
under a cooktop range, Damage to plastic tub will occur,
Figure 3 and note the location of water inlet valve.
Electric Shock Hazard 3. If you connect to a sink trap, local codes may require you to
-_ f j install an air gap kit, not included. The drain hose will be routed
Disconnect electrical power at the fuse box or
circuit breaker box before beginning installation. from dishwasher to air gap inlet as shown in Figure 6. An air
© gap kit is available from a plumbing supply store. (If the drain
Failure to follow this warning could result in death , 90°---_ /-- 90 ° __ Property Damage
hose is installed through the floor, an air gap is necessary).
or serious injury.
34,'/_"min. Electrical, water, Do not use the furnished drain hose or a rubber garden hose
and drain lines 4. If you connect to a disposer, the large end of drain hose will
for the water supply line. Either of these hoses can burst.
must be confined fit. Figure 7(a). The knock out plug must be removed from
© @ Flooding may occur and cause property damage.
• Examine dishwasher and locate connections. See Step 4. to shaded area. | 8 _
inside disposer inlet before making the final fit to drain
24 '''_
rain. hose. See Figure 7(b).
• Locate dishwasher where there is easy access to drain, %'
, i_ . Be sure water inlet valve is )rotected from freezing. If valve
water, and electrical lines. The best location is on either side freezes and ruptures, flooding may occur. Drain
of the kitchen sink for access to existing plumbing and ease f 3. Determine amount of tubing needed to connect hot water
Motor
End /
•Largerend
ofhose
in loading dishes. See Step 4. supply to the unit's water inlet valve. Copper tubing must have a . / _ltsdisposer
minimum _/8"OD. High-pressure and high-temperature rated Cutfor_/, connection. / Inlet filling.
• Electrical, water, and drain connections are not the same for
all age, brands, or models of dishwashers. Check the plastic tubing with a minimum inner diameter of V4"may be ...... Drain Hose
location and length of home utilities. See Step 4. used. A shut-off valve installed outside dishwasher cabinet is F_ure 71a)
Cot [or 3./# n connection.
best. See Figure 4.
• A 15-20 amp, grounded, 120 volt AC only, electrical supply is
required. See Steps 4 and 8.
• If dishwasher drain hose will be connected to a food
Flgut_ 2 Drain Air Gap
disposer for the first time, knock out plug located inside
disposer inlet. See Steps 4 and 6.
IMPORTANT: For proper operation and appearance of unit,
• Kinked water or drain hoses can cause problems. See Step cabinet opening should have dimensions as shown in Figure 2.
6. If unit is to be placed in a corner, there must be at least a 2-inch
• Dishwashers need to be connected to a hot water supply side clearance to open door.
Alternate
INSTALLER: Leave Installation Instructions with owner. with enough water pressure to insure an adequate fill. 2. Remove any carpet from area to provide motor clearance. Floor Drain
See Steps 4 and 7. should be flat and free of any obstruction.
OWNER: Read your dishwasher Use and Care Manual. It contains Through
important safety information for operating this appliance. It also has • Each home installation differs. You will need additional Floor into
many suggestions for getting the best results from your dishwasher. parts listed above to complete your installation. _pamte
IMPORTANT: Drain, water, and electrical lines should be
See Steps 4 and 7. Trap
Printed in U.S.A. 154427301 roughed-in before going any further.
• Flush water line prior to making the final connection to
(04/07) ve
prevent clogging of dishwasher's filter screen. See Step 7.
II r .oekout
• The dishwasher will look, sound, and perform best when _in Sink at Right
properly leveled. See Step 5. (NOTE: If levelers are Electric Shock Hazard 2" Drain Hose Hole
removed during installation, make sure the floor is flat and
Electrical, water, and drain lines must be confined Flgnre 71b)
free of any obstruction.)
to shaded areas in Figure 2.
• Anchorthe dishwasher. See Step 9. Figure 4
Electric conductors, water, and drain could be
Read all instructions before installing dishwasher.
damaged.
For your safety, please read and observe all safety Failure to follow these instructions could result in 4. Cut water access hole in shaded area in Figure 2. 5. Before cutting drain hose access, check both sides of selected
instructions. This guide will help you anticipate drain, water, and fire or electric shock. area to avoid interference. Cut a 2" diameter hole in shaded
5. Route water supply line into installation area.
electrical connections, and help you select the best location for the area shown in Figure 2.
dishwasher. IMPORTANT: Incoming hot water temperature should be at
least 120°F (49°C). Water pressure should be between 6. If the cabinet wall is wood, sand edges of hole until smooth and
NOTE: If dishwasher is installed at end of a cabinet line, sides 20-120 psi. rounded. If cabinet wall is metal, cover all sharp edges with
and back must be fully enclosed. electrical or duct tape to avoid cutting drain hose.
1. Remove two (2) screws at front of the kickplate assembly using
a #2 Phillips screw driver. NOTE: You can order a Cabinet Seal Kit (Kit # 154528701) by
Tip Over Hazard contacting your dealer or parts supplier. This kit provides a Drain
2. Tilt and pull forward to remove. See Figure 1.
Do not use dishwasher until completely installed. seal between the unit and cabinets once installation is 1. Review Figures 5 and 6 to see the different ways to connect
NOTE: It is not necessary to remove the outer door for installation. complete. (This kit is included on select models). dishwasher to drain system. Choose method that best suits
Do not push down on open door. However, you might find it more convenient to do so. You your need.
can find directions for removing door in Step 10.
Failure to follow this warning can result in serious
injury.
Figure5
FdcAplateAssembly Entry Must be
Above
Adjustable Toeplate IMPORTANT: Do not cross drain, water, and electrical lines in
(Insulation avdilable front of dishwasher motor or frame.
somemodols)
Tools and Materials Needed for Kicl_plate Locating the Connections
Installation 1. Review dimensions in Figure 3 to locate dishwasher's drain,
water, and electrical connections.
Pipe Joint Compound (for iron pipe plumbing) or I,_ 23_/s "
Pipe Thread Tape (for sealing threads)
Pliers Fl_u/_ I
Door in
Safety Glasses l/a- opon posltion . If you connect to a sink drain, entry will need to be above
Saw, Keyhole or V2", 1V2" to 2" Hole Cutters n.
trap. A "Y" branch tailpiece and connector kit, not included, will
Screw Drivers, Slotted and #2 Phillips (magnetic tip 3. Locate water inlet valve behind kickplate on bottom left make this method easier and includes all needed fittings and
preferred) underside of unit. The valve has a 3/s"NPT female fitting. instructions. See Figure 5.
Tape, Electrical or Duct 4. Wrap 90 ° elbow (not included) with pipe thread tape (or apply
33/+,,
Use'/4 "/.agscrews
(not includ_d)
Leg Leveler Adjustment Chart Liner
Height of Number of Turns to
Figure I0 Figure 15 Door
Cabinet Opening Adjust Levelers
34" (86.4cm) 0
The drain hose loop must be at least 32" !_ from the lloor
34W' (86.7cm) 2 to insure proper drainage. Wall
345/16"(87.2cm) 6 Side
341/2" (87.6cm) 9 Note: If mounting your dishwasher to the countertop or to the floor View
is not a desirable option, you can order the side mount kit,
For additional height add shims under levelers.
154477201, by contacting your dealer or parts supplier. This allows
you to install the dishwasher by securing it to the cabinets or
. Move dishwasher to front of installation area.
partitions on either side of the unit. The kit utilizes the front frame of Appearance of console and door may
3. Loosen the front and rear leveling legs by turning Junction Box the dishwasher to secure the unit to the cabinet or partitions. vary from your model.
counterclockwise. Refer to chart for number of turns. See (in place)
Figure 8. Front levelers should allow 1/4"below underside of Property Damage
countertop. Do not solder within 6" of the water inlet valve. Damage to 6. Unlatch door and open while supporting outer door on both sides
the plastic parts in the valve may occur. PTgure 12 at bottom to keep in place. Align screw holes and replace
screws.
Use care that no sealer, dirt, or other objects enter the valve.
J ///i!
Damage to the filter screen may occur.
. Inside junction box, attach ground wire under head of grounding
Be sure the dishwasher is placed where the water inlet valve screw and tighten. See Figure 13.
will be kept from freezing. If the valve freezes, it may rupture
4. Connect incoming black lead to dishwasher's black lead and
and flooding may occur.
incoming white lead to dishwasher's white lead with wire nuts or
Water Line other suitable connectors, not included. Wire nuts should be
Before starting the dishwasher,
tight. Electric Shock Hazard
1. Flush water line before connecting it to water inlet valve to
prevent early clogging of filter screen. Place a bunched towel Disconnect electrical power at the fuse box
check these items:
over end of line to prevent splashing. Open valve for a few Conduit Ground Wire or circuit breaker box before beginning
Connector
seconds and let water drain into a pan. Turn off water supply installation. _1 Drain hose is assembled to drain pump.
at shut-off valve. Failure to follow this warning could result in _1 All packing materials and consumer literature have been
death or serious injury. removed from u nit.
_1 Dishwasher is level and securely fastened.
_1 Open and close door to make sure it does not hit
Figure II
4. If levelers have to be removed, make sure floor is free of surrounding cabinet or countertop.
obstructions. Cut Hazard _1 Water and drain lines have no kinks.
5. Place dishwasher inside cabinet area so that it is centered in Metal color panels are sharp and should be
_1 Wiring connections to junction box are tight.
opening. Use caution when moving dishwasher to prevent handled with care. Wear gloves to protect
Through White Wire to Water supply is turned on.
Cabinet \ hands.
damage to dishwasher, floor, and cabinets. White Wire
(Neutral) Joints are free of leaks.
6. Check that dishwasher is level from side to side by placing a Failure to follow this warning may result in
Black Wire to injury.
level against the top front section of the tub. See Figure 9a.
S Black Wire (Hot)
I
This unit has copper lead wires. If all connections are correct, there are no leaks,
clamp. IMPORTANT: Be careful not to overtighten clamp or
Joining aluminum building wire to stranded copper wire Appearance of console and door may and unit runs properly, replace the kickplate
you may damage end of hose. Do not connect hose to vary from your model.
should be done by a qualified electrician using materials assembly before placing unit into operation.
horizontal pipe between sink drain and disposer.
recognized by UL and local codes.
4. Be sure unit does not rest on drain hose. It should be free of Failure to follow this warning could result in
Do not use an extension cord. Such use can result in fire,
electrical components and door springs. Do not cut corrugated electrical shock, or other personal injury. electric shock.
drain hose. Pull excess through cabinet and place under sink. Failure to follow these instructions could result in death or
Make sure hose does not come in contact with any sharp edges. serious injury.
See Figure 10.