Professional Documents
Culture Documents
SE Rotary Paddle Level Switch - B0
SE Rotary Paddle Level Switch - B0
SE Rotary Paddle Level Switch - B0
com
INTRODUCTION
APPLICATIONS BENEFITS
1 Plastics and synthetics 1 Airtight sealed device.
1 Chemicals and fertilizer 1 Outdoor and strenuous environment application
1 Pharmaceuticals 1 Stable and reliable performance.
1 Food and beverage, 1 Lightweight and easy to install
1 Agriculture and fodder mills/depots 1 Practically designed to allow maintenance, checks
1 Cement as well as ceramics and replacement
1 Power plants 1 Not necessary to remove the complete set from
1 Various incinerators the tank.
STRUCTURE SHAFT
FLANGE CLUTCH MOTOR
PADDLE BODY
OIL-SEAL
NUT
PCB SPRING
LED
BODY
PADDLE
LED COVER
OIL-SEAL HOUSING
BEARING MOTOR
MINI TYPE SE3
1
WORKING PRINCIPLE & TORQUE ADJUSTING
CONTROL SWITCH
WORKING PRINCIPLE WHITE
M
1. A synchronous turning motor indicates the
Limit
tank or container’s material isn't obstructing BLACK
the paddles,C & L [COM & NC] are connected. SW.
NO.1
2. When the material is obstructing the paddles, BLUE L
C&L [COM & NC] are disconnected, C&H
[COM & NO] are connected and the motor's YELLOW C Limit
current is cut off. SW.
NO.2
3. When the material drops away from the RED H
paddles and the motor starts again C & L
[COM & NC] connect and the cycle has begun
once again.
TORQUE ADJUSTING MECHANISM
AND WIRING 1 Do not tamper with the spring as it may cause
The torque spring is applied to adjust the shaft the Rotary Paddle to malfunction.
output torque. Default settings aret "weak" and
can be adjusted to the customer’s target based Spring adjusting hole
on the tank contents and S.G. (special gravity)
of the material.
Higher S.G. materials require stronger torque weakest
settings. Start with high settings and slowly weak
release the torque force until the appropriate strong
setting is found.
Resetting torque strongest
adjusting spring
strongest
strong
weak
weakest
110Vac NC NO
or 24Vac
COM
220Vac 110Vac
220Vac NC COM NO
Available: SE110, 120, 130, 140, 160, 170 240Vac
20 ~ 55 Vdc
V+ V- NO COM NC V+ V-
24Vdc
SEA-110D-B
PA2 080104 CC
NC COM NO
20~55 NO NC
Vdc COM DC type
GND
Available:SE110E Available:SE3
2
STANDARD TYPE
SCREW MODEL
SE110 Series
Horizontal mounting SE110 Series SE111 Series
Operation Temperature (-20BC ~ 70BC)
Weight: 1.2 kg
PCD130
4-f15
1"PF
f155
FLANGE MODEL
SE111Series
100 f98
Horizontal mounting f98
100
Operation Temperature (-20BC ~ 70BC)
f10
80
f8
65 30
100
3
STANDARD TYPE
HI-TEMP TYPE
SE140A/B/C/D
Horizontal mounting SE140A/B/C/D Series SE141A/B/C/D Series
Temp. (-20BC ~ 200BC)
Weight: 2.1 kg f98
f98
1/2"PF
HI-TEMP TYPE 1/2"PF
PROTECTIVE TUBE TYPE
SE141A/B/C/D/E 210
Horizontal /Vertical mounting 189
Operation Temperature (-20BC ~ 200BC)
f155
Standard Length (option):
f155
L--250mm (2.6 kg) 4 PCD130
L--500mm (2.9 kg) 4
L--750mm (3.2 kg) PCD130
Special length is made by order f10 4-f15 f27.2
92 f10 L
30
4-f15
100 80
65
HI-TEMP SHAFT
LENGTH ADJUSTABLE TYPE SE146A/B/C/D/E Series SE160A/B/C/D/E Series
SE146A/B/C/D/E
Vertical mounting
Operation Temperature (-20BC ~ 200BC) f98
Standard Length (option):
f98
L– 450~630mm (3 kg)
L– 650~1000mm (3.3 kg) 1/2"PF
L– 760~1200mm (3.5 kg)
1/2"PF 135
Special length is made by order
189
f155
f8
30 30
100 100
4
Housing cover code:
0: Aluminum cover
1: Aluminum cover with LED lamp
MINI TYPE(Aluminum alloy cover)
177
30 L=86mm
30 18 f88
38 LED indicator
LED indicator
80 8
f79
100
f79
3/4"PF
3/4"PF
1/2"PF
1/2"PF
f8 cable 300mm f8 cable 300mm
L=150~400mm
L=150~400mm
30
LED indicator 30 18 LED indicator
f88
21.7
100
f79 100
21.7 3/4"PF f79
3/4"PF
1/2"PF
f8 cable 300mm 1/2"PF
f8 cable 300mm
5
MINI TYPE(Plastic cover)
177
30 L=86mm
30 18 f88
38
80 8
f79
100
f79
3/4"PF
3/4"PF
1/2"PF
1/2"PF
f8 cable 300mm f8 cable 300mm
L=150~400mm
L=150~400mm
30
30 18
f88
21.7
100
f79 100
21.7 3/4"PF f79
3/4"PF
1/2"PF
f8 cable 300mm 1/2"PF
f8 cable 300mm
6
MOUNTING EXAMPLES
Min.3/4"PF 30
Max.45
Max.15mm
7
EXAMPLES
SE130
SE141
SE110
SE120
15B
SE111
INSTALLATION NOTICES
1. Side mount the sensor at a downward angle of 15° ~20° to decrease the material inflow impact.
2. For high temperature application (more than 70°C), please use the SE149 Series.
3. For SE110~SE140 using a 1" inlet, please apply the scimitar model and screw directly.
4. For SE130, SE146 series have flexible and extendible shafts.
5. Please ensure the lead wire enters the housing from the bottom and the nuts are fastened to secure the device.
8
HOW TO ORDER
( )
MODEL NO.
119 : Standard model 149 : Hi-temp model
120 : Shaft protective tube model 160 : Cable wire model
130 : Shaft length adjustable model
VOLTAGE
A : 110Vac B : 220Vac C : 240Vac D : 24Vac
E : 24Vdc 50/60Hz
MOUNTING
PADDLE SHAPES
SE110~SE170 A B,C,D E
A : 100 x30 (WxH)
B : 65x80 (WxH)
C : 65x120 (WxH) W W
W
D : 80x80 (WxH)
E : 50x30 (WxH) H
H
F : Scimitar H
J : 200x28 (WxH) F J
S : others - : None 132
100 28
200
Material:SUS
30
LENGTH (mm)
0500: below 500mm
1000: 501~1000mm
1500: 1001~1500mm
Note
1. Check the voltage 24Vac, 110Vac, 220Vac or 240Vac, 50/60 Hz.
2. Check the side or top mounting.
3. Check the material specific gravity (S.G.) value.
4. If blockages are frequent or vibrating motors are installed onto the tank wall, our SA140 capacitance level
sensor is more suitable.
5. Check whether the rotary paddle can fit through the flange inlet or from the inside of the tank
9
HOW TO ORDER
SE3 ( )
HOUSING TYPE
7: Ex proof type
8: General type
HOUSING COVER
0: Aluminum cover
1: Aluminum cover with LED lamp
2: Plastic cover
※1 and 2 are not available for SE37.
MODEL
0: Standard
2: Shaft protective tube
4: High temperature
5: High temperature shaft protective tube
SUPPLY VOLTAGE
A: 110Vac, 50/60Hz
B: 220Vac, 50/60Hz
C: 240Vac, 50/60Hz
D: 24Vac, 50/60Hz
E: 24Vdc
CONNECTION
Size for flange or screw Specification
C: 3/4" I : 4" M: 5kg/cm2 Z : PN40
D: 1" J: 5" N: 10kg/cm2 Q: PT
3 : 1-1/4" K: 6" O: 150Lbs R: PF(G)
E: 1-1/2" S : Special P : 300Lbs T: BSP
F: 2" W: PN10 U: NPT
G: 2-1/2" X : PN16 S : Special
H: 3" Y : PN25
10
EXPLOSION PROOF MODEL
NEPSI PROOF No.GYJ111214 Ex d IIC T3~T6
PTB PROOF No. 05 ATEX 1029 II 2G Ex d IIB T6~T3 Gb
II 2D Ex tb IIIC T85BC~T200BC Db IP65
1 Power source : (A)110Vac, (B)220Vac, (C)240Vac 1 Connect : 1"PF screw or flange 1"~6"
(D)24Vac, 50/60Hz 2-1/2"H5kg/cm2 (std.)
1 Power consumption :3W 1 Housing material : AL Alloy, ADC-12
1 Contact capacity : SPDT, 3A/250Vac 1 Conduit : 1/2" (std.) or 3/4"NPT
1 Rotary speed : 1 R.P.M. 1 Material density : 0.5 g/cm3
1 Insulation test voltage : AC 1500VH1minute
f155 20
14
f10 4- f15
PCD 130
75
30
100
100
30
100
11
EXPLOSION PROOF MODEL
NEPSI PROOF No.GYJ111214 Ex d IIC T3~T6
PTB PROOF No. 05 ATEX 1029 II 2G Ex d IIB T6~T3 Gb
II 2D Ex tb IIIC T85BC~T200BC Db IP65
EXPLOSION PROOF EXPLOSION PROOF EXPLOSION PROOF
HI-TEMP SHAFT HI-TEMP ADJUSTABLE CABLE WIRE MODEL
PROTECTIVE TUBE MODEL SHAFT MODEL SE177
SE175 SE176
Horizontal /Vertical mounting Vertical mounting Vertical mounting
Temp. (-20BC ~ 200BC) Temp. (-20BC ~ 200BC) Temp. (-20BC ~ 70BC)
Special length is made by order Special length is made by order Special length is made by order
f113
f113 f113
108
108 108
f90
f90
45 f155 20
45
f155 14
14
1"PF f14
f27.2
PCD 130
f6 4-f15
f10 f9 PCD 130
L=250~ L=450~
f14 4-f15
750 mm L=450~ 4000 mm
1200 mm f12.7 f28 108
30
30 100
100
4 Paddle Introduction
A E
(E) 50x30 (WxH), Suitable for high
(A) 100x30 (WxH), Min. fixed hole
diameter size f90mm. S.G. raw materials. Use a
small size paddle to decrease
W W the impact of material falling
directly on paddle.
H
H
F
B,C,D (F) Scimiter model paddle, Screw
(B) 65x80 (WxH), Directly mounted 132 tightly on the 1" diameter
into 2" fixed hole. fixed hole, It Is easier to
W (C) 65x120 (WxH), Directly mounted mount and dismount.
into 2" fixed hole. 100
(D) 80x80 (WxH)
H
30
12
HOW TO ORDER
SE1 7 ( )
MODEL NO.
70: Screw model 74: Hi-temp model
71: Flange model 75: Hi-temp shaft protective tube model
72: Shaft protective tube model 76: Hi-temp shaft length adjustable model
73: Shaft length adjustable model 77: Cable wire model
VOLTAGE
A : 110Vac B : 220Vac C : 240Vac D : 24Vac
MOUNTING
Size for flange or screw Specification
D: 1" I : 4" M: 5kg/cm2 Z : PN40
E: 1-1/2" J : 5" N: 10kg/cm
2
Q: PT
F : 2" K: 6" O: 150 Lbs R : PF (G)
G: 2-1/2" S : Others P : 300 Lbs T : BSP
H: 3" 3 : 1-1/4" W: PN10 U : NPT
X: PN16 S : Others
Y: PN25
PADDLE SHAPES
C : 65x120 (WxH)
W W
D : 80x80 (WxH) W 100
E : 50x30 (WxH) H
H
F : Scimitar H
S : Others 30
LENGTH (mm)
Note
1. Check the voltage 24Vac, 110Vac, 220Vac, 240Vac, 50/60 Hz.
2. Check the side or top mounting.
3. Check the material specific gravity (S.G.) value.
4. If blockages are frequent or vibrating motors are installed onto the tank wall, our SA140 capacitance
level sensor is more suitable.
5. Check whether the rotary paddle can fit through the flange inlet or from the inside of the tank
13
Global Network
Germany
China
U.S.
Taiwan U.S.
Singapore
China
FINE AUTOMATION CO., LTD. - Shanghai Factory
No.451 DuHui Rd, MinHang District, Shanghai,
China 201109
TEL: 86-21-6490-7260
FAX: 86-21-6490-7276
EMAIL: info.sh@fine-tek.com Distributor:
Singapore
FINETEK PTE LTD. - Singapore Office
No. 60 Kaki Bukit Place, #07-06 Eunos
Techpark 2 Lobby B, Singapore 415979
TEL: 65-6452-6340
FAX: 65-6734-1878
EMAIL: info.sg@fine-tek.com
08-SE-B0-EP, 01/23/2015