Professional Documents
Culture Documents
Huawei Ran Parameters Settings PDF Free
Huawei Ran Parameters Settings PDF Free
xls 文档密级
Recording
Date Contents
2008/3/4 Draft
2008/8/28 Add current value
DMPI
Author
Kevin jiang
Kevin jiang
BACK
Uplink power control parameters
No. Parameter ID Parameter Meaning Default Value Current Value Relevant Command Level
1 PowerOffsetPpm Power offset between the last access Signalling: -3 dB Signalling: -3 dB Set: ADD PRACHTFC Cell
preamble and message control part Services: -2 dB Services: -2 dB Modify: The PRACH TFC needs to
be deleted before being reconfigured.
2 ConstantValue Constant for PRACH initial transmit -20, that is, -20 -20, that is, -20 dB Cell
power dB Set: ADD PRACHBASIC
3 PowerRampStep Power increase step of random access 2, that is, 2 dB 2, that is, 2 dB Modify: The PRACH needs to be
preamble deleted before being reconfigured.
4 PreambleRetransMax Maximum of preamble retransmission 8 times 20 times
5 Mmax Max preamble loop 8 times 8 times Set: ADD RACH Cell
267469637.xls
Power Control Parameters
267469637.xls
267469637.xls 文档密级
BACK
1ST
Physical
Parameter Name Command Content Range Defaule Value Current Value implemen
unit/step
ted Value
Inter-RAT Handover
Index number uniquely identifying the configuration
Service parameter of the typical service parameters.
ADD TYPRABBASIC 0~99 none
index Content: index number identifying the configuration
of the typical traffic RAB.
Handover type.
Content: -
HO_TO_GSM_SHOULD_BE_PERFORM:
Handover to the 2Gnetwork is performed whenever
2G signals are available. -
HO_TO_GSM_SHOULD_NOT_BE_PERFORM:
Handover to the 2G network is performed when 3G HO_TO_GSM_SHOULD_BE_PERFOR
signals are weak but 2G signals are strong. - M,
Service Handover HO_TO_GSM_SHALL_NOT_BE_PERFORM: HO_TO_GSM_SHOULD_NOT_BE_PE HO_TO_GSM_S HO_TO_GSM_S
ADD TYPRABBASIC none
Indicator Handover to the 2G network is not performed even RFORM, HOULD_NOT_B HOULD_NOT_B
when 3G signals are weak but 2G signals are HO_TO_GSM_SHALL_NOT_BE_PERF E_PERFORM E_PERFORM
strong. ORM
If the handover type is available from the service
properties assigned by the Core Network (CN),
handovers are performed in the way specified by the
CN. If the handover type is not specified by the CN,
handovers are performed in the way specified in the
typical traffic parameter.
Inter-RAT cell type ADD GSMCELL Content: Indicating the inter-RAT cell type. NO_CAPABILITY, GSM, GPRS, EDGE none none GPRS
2D Event
Physical
value
range: 0,
10, 20,
Time delay to trigger the event 3A. 40, 60,
ADD Content: The value of this parameter is relevant to 80, 100,
D0, D10, D20, D40, D60, D80, D100,
3A event trigger CELLINTERRATHOC the slow fading characteristic. The larger the value 120, 160,
D120, D160, D200, D240, D320, D640, D0 D0
delay time[ms] OV/SET of this parameter, the lower the incorrect decision 200, 240,
D1280, D2560, D5000
INTERRATHOCOV probability, but the slower the response of the event 320, 640,
3A to measurement signal change. 1280,
2560,
5000
Physical
unit: ms
3C Event
Physical
value
range:
-110 to
Quality requirement for the inter-RAT cell during an
-48 (The
inter-RAT handover with CS domain services.
SET value 1
Content: This parameter is used to set
Inter-RAT CS INTERRATHONCOV/ correspon
measurement control on the event 3C. The event
handover decision ADD
3C is triggered when the quality of the target
0 to 63 ds to the 21 21 14
THD[dBm] CELLINTERRATHON physical
frequency is higher than this threshold. Note that the
COV value
value 0 means the physical value is smaller than
-110, 2 to
-110 dBm.
-109, ...,
63 to -48)
Physical
unit: dBm
Physical
value
range:
-110 to
-48 (The
Quality requirement for the inter-RAT cell during an
SET value 1
inter-RAT handover with PS domain services.
Inter-RAT PS INTERRATHONCOV/ correspon
Content:The event 3C is triggered when the quality
handover decision ADD
of the target frequency is higher than this threshold.
0 to 63 ds to the 21 21 14
THD[dBm] CELLINTERRATHON physical
Note that the value 0 means the physical value is
COV value
smaller than -110 dBm.
-110, 2 to
-109, ...,
63 to -48)
Physical
unit: dBm
Value range:
COEXIST_MEAS_THD_CHOICE_INTE
RFREQ,
COEXIST_MEAS_THD_CHOICE_INTE
RRAT
COEXIST_MEAS_THD_CHOICE_INTE
InterFreq & InterRat Type of event 2D/2F measurement thresholds when RFREQ: choosing the inter-frequency COEXIST_MEA COEXIST_MEA
coexist measure ADD CELLHOCOMM inter-frequency and inter-RAT measurement coexist. oriented parameters as event 2D/2F none S_THD_CHOIC S_THD_CHOIC
threshold choice measurement thresholds for inter- E_INTERFREQ E_INTERFREQ
frequency measurement
COEXIST_MEAS_THD_CHOICE_INTE
RRAT: choosing the inter-RAT oriented
parameters as event 2D/2F
measurement thresholds for inter-RAT
measurement
BACK
Handover Parameter Meaning
Parameter Name Command
Parameters
InterRATFilterCoef
Inter-RAT measurement filter coefficient
2D2FFilterCoef
InterRATReportMod
Inter-RAT measurement report mode
e
2D2FMeasQuantity
Inter-RAT measurement quantity
3AMeasQuantity
InterRATCSThd2DRSCP
InterRATPSThd2DRSCP
RSCP-Based inter-RAT measurement
start/stop thresholds
InterRATCSThd2FRSCP
For RNC
InterRATPSThd2FRSCP
Set or modify: SET
INTERRATHOCOV
For Cell
InterRATCSThd2DEcN0
Set: ADD
CELLINTERRATHOCOV
InterRATPSThd2DEcN0
Ec/No-Based inter-RAT measurement
Query: LST start/stop thresholds
InterRATCSThd2FEcN0
CELLINTERRATHOCOV
InterRATPSThd2FEcN0
Modify: MOD
CELLINTERRATHOCOV
Coverage-Based
Inter-RAT Handover InterRATCovHOCSThd
Management Inter-RAT handover judging thresholds
Parameters InterRATCovHOPSThd
TrigTime2D
Time-to-Trigger related to inter-RAT
TrigTime2F
handover event
TrigTime3A
Hystfor3A
Hystfor2D
Hysteresis related with inter-RAT
handover coverage
Hystfor2F
HystforInterRAT
For Inter-RAT
CK
Default Value
Current Value Level
D3 D3
Periodical_reporting Periodical_reporting
0 0
Require Require
2D2FMeasQuantity: BOTH
2D2FMeasQuantity: BOTH
3AMeasQuantity:
3AMeasQuantity: CPICH_RSCP
CPICH_RSCP
InterRatCSThd2DRscp: -100
(dBm)
InterRatCSThd2DRscp: -100 (dBm)
InterRatPSThd2DRscp: -110
InterRatPSThd2DRscp: -110 (dBm) (dBm)
InterRATCSThd2DEcN0: -14
RNC
(dB)
InterRATCSThd2DEcN0: -14 (dB)
Cell
InterRATPSThd2DEcN0: -15
InterRATPSThd2DEcN0: -15 (dB) (dB)
16, that is, -95 dBm 16, that is, -95 dBm
TRIGTIME3A: D0 TRIGTIME3A: D0
30 s 30 s
0 dB 0 dB NCell
IRHOUsedFreqCsThdEcN0:
-12 (dB)
IRHOUsedFreqCsThdEcN0: -12 (dB)
IRHOUsedFreqPsThdEcN0:
IRHOUsedFreqPsThdEcN0: -13 (dB) -13 (dB)
RNC
IRHOUsedFreqCsThdRscp: -97 (dBm) IRHOUsedFreqCsThdRscp:
-97 (dBm) Cell
IRHOUsedFreqPsThdRscp: -107 (dBm)
IRHOUsedFreqPsThdRscp:
-107 (dBm)
60 s 60 s
D3 D3
0 dB 0 dB
Required Required
RNC
21, that is, -90 dBm 21, that is, -90 dBm Cell
30 s 30 s
16 times 16 times
60 s 60 s
NCell
- -
- 58, that is, -115 dBm - 58, that is, -115 dBm
0 dB 0 dB
RAB_Downsizing_Switch
QueueAlgoSwitch
PeemptAlgoSwitch
BACK
80% 80%
80% 80%
60% 60%
75% 75%
80% 80%
85% 85%
90% 90%
0 0
modify them
through MOD
AAL2PATH /
MOD IPPATH;
Query them
through LST
AAL2PATH /
DSP
AAL2PATH /
LST IPPATH /
DSP IPPATH.
100%
50%
50%
100%
100%
100%
100%
100%
100%
RAB_DOWNSI RAB_DOWNSI
ZING_SWITCH ZING_SWITCH Set or modify: SET CORR
:1 :1
QUEUEALGOS QUEUEALGOS
WITCH: OFF WITCH: OFF Query: LST CORRMALGOSWI
PREEMPTALG PREEMPTALG QueueAlgoSwitch and
OSWITC: OFF OSWITC: OFF PeemptAlgoSwitch
Set or modify: SET QUEU
Query: LST QUEUEPREEMPT
BACK
Cell load reshuffling (LDR) algorithm parameters
No. Parameter ID Parameter Meaning Default Value Current Value
1 ULLDR Uplink/Downlink LDR OFF OFF
DLLDR algorithm switches
UlLdrFourthAction Others:
NOACT
UlLdrFifthAction
UlLdrSixthAction
UlLdrSeventhAction
UlLdrEighthAction
DlLdrFirstAction
DLLDRSecondAction
DLLDRThirdAction
DLLDRFourthAction
DLLDRFifthAction
DlLdrSixthAction
DlLdrSeventhAction
DlLdrEighthAction
DlLdrNinthAction
DlLdrTenthAction
2 ULLDRBERateReductio Number of users processed ULLDRCSInte ULLDRCSInte
nRabNum by uplink/downlink LDR rRATSHOULD rRATSHOULD
action BEHOUserNu BEHOUserNu
m, m,
ULLDRCSInte ULLDRCSInte
rRATSHOULD rRATSHOULD
NOTBEHOUse NOTBEHOUse
rNum and rNum and
ULLDRAMRR ULLDRAMRR
ATEREDUCTI ATEREDUCTI
ONRABNUM ONRABNUM
are set to 3 by are set to 3 by
default; others default; others
are set to 1 by are set to 1 by
default. default.
ULLDRPSRTQosReneg DLLDRCSInte DLLDRCSInte
RabNum rRATSHOULD rRATSHOULD
BEHOUserNu BEHOUserNu
m, m,
DLLDRCSInte DLLDRCSInte
rRATSHOULD rRATSHOULD
NOTBEHOUse NOTBEHOUse
rNum and rNum and
DLLDRAMRR DLLDRAMRR
ATEREDUCTI ATEREDUCTI
ONRABNUM ONRABNUM
are set to 3 by are set to 3 by
default; others default; others
are set to 1 by are set to 1 by
default. default.
ULLDRCSInterRATSH
OULDBEHOUserNum
ULLDRCSInterRATSH
OULDNOTBEHOUserN
um
ULLDRPSInterRATSH
OULDBEHOUserNum
ULLDRPSInterRATSH
OULDNOTBEHOUserN
um
ULLDRAMRRATERED
UCTIONRABNUM
DLLDRBERateReductio
nRabNum
DLLDRPSRTQosReneg
RabNum
DLLDRCSInterRATSH
OULDBEHOUserNum
DLLDRCSInterRATSH
OULDNOTBEHOUserN
um
DLLDRPSInterRATSH
OULDBEHOUserNum
DLLDRPSInterRATSH
OULDNOTBEHOUserN
um
MAXUSERNUMCODE
ADJ
DLLDRAMRRATERED
UCTIONRABNUM
3 UlInterFreqHoBWThd UL or DL inter-frequency 200k bps 200k bps
cell load handover
DlInterFreqHoBWThd maximum bound width
4 LdrPeriodTimerLen LDR period timer length 10 s 10 s
2 OlcPeriodTimerLen OLC period timer length 3000, that is, 3 3000, that is, 3
s s
3 UlOlcTrigThd Uplink or downlink OLC UlOlcTrigThd: UlOlcTrigThd:
trigger threshold and 95% 95%
DlOlcTrigThd release threshold DlOlcTrigThd: DlOlcTrigThd:
95% 95%
UlOlcRelThd UlOlcRelThd: UlOlcRelThd:
80% 80%
DlOlcRelThd DlOlcRelThd: DlOlcRelThd:
80% 80%
4 UlOlcFTFRstrctTimes Uplink or downlink OLC 3 times 3 times
DlOlcFTFRstrctTimes fast TF restriction times
5 UlOlcFTFRstrctRabNum Uplink or downlink OLC 3 3
DlOlcFTFRstrctRabNum fast TF restrict RAB
6 RateRstrctTimerLen number
OLC fast TF restrict data RateRstrctTime RateRstrctTime
rate restrict timer length rLen: 3000 (3 rLen: 3000 (3
and recover timer length s) s)
RateRecoverTimerLen RateRecoverTi RateRecoverTi
merLen: 5000 merLen: 5000
(5 s) (5 s)
7 RateRstrctCoef OLC fast TF restrict data 68, that is, 68% 68, that is, 68%
rate restrict coefficient
8 UlOlcTraffRelRabNum Uplink or downlink release 0 0
RAB number
8 Uplink or downlink release 0 0
DlOlcTraffRelRabNum RAB number
algorithm parameters
Relevant Command Level
Set: ADD CELLALGOSWITCH \NBMSwitch Cell
Query: LST CELLALGOSWITCH
Modify: MOD CELLALGOSWITCH \NBMSwitch
Set this parameter through ADD NODEBALGOPARA,
modify it through MOD NODEBALGOPARA, and
query it through LST NODEBALGOPARA NodeB
algorithm parameters
Relevant Command Level
Cell
Set: ADD CELLLDM
algorithm parameters
Relevant Command Level
Cell
Cell
Set or modify: SET LDCPERIOD
RNC
Query: LST LDCPERIOD
ol parameters
Relevant Command Level
Set: ADD CELLALGOSWITCH \NBMLdcAlgoSwitch Cell
Query: LST CELLALGOSWITCH
Modify: MOD CELLALGOSWITCH \NBMLdcAlgoSwitch
Set or modify: SET LDCPERIOD RNC
Query: LST LDCPERIOD
Cell
Set: ADD CELLLDM
PS inactive parameters
No. Parameter ID Parameter Meaning Default Value
1 PSINACTTMRFORIN Interactive service T1 20 s
T
2 PROTECTTMRFORI Interactive service T2 20 s
NT
3 PSINACTTMRFORB Background service T1 20 s
AC
4 PROTECTTMRFORB Background service T2 20 s
AC
5 PSINACTTMRFORI IMS service T1 20 s
MS
6 PROTECTTMRFORI IMS service T2 20 s
MS
el configuration parameters
Current Value Relevant Command Level
D1024, that is, 1024 bytes Set: ADD TYPRABDCCCMC RNC
D128, that is, 128 bytes Query: LST TYPRAB
D240, that is, 240 ms Modify: MOD TYPRABDCCCMC
D2560, that is, 2.56 s
D4000, that is, 4 s
3_Rates
RNC
3_Rates
ability parameters
Current Value Relevant Command Level
2 (1 dB) For RNC level RNC/Cell
Set or modify: SET DCCC
Query: LST DCCC
2 (1 dB) For cell level
64 Kbit/s Set: ADD CELLDCCC
32 Kbit/s Query: LST CELLDCCC
ansfer parameters
Current Value Relevant Command Level
180 s RNC
Set or Modify: SET UESTATETRANS
D64 (64 bytes)
Query: LST UESTATETRANS
180 s
180 s
D1024 (1024 bytes)
active parameters
Current Value Relevant Command Level
20 s RNC
Set or modify: SET PSINACTTIMER
20 s
Query: LST PSINACTTIMER
20 s
20 s
20 s
20 s
50 ms
80, that is 8%
14
1
BACK
Cell channel power distribution parameters
No. Parameter ID Parameter Meaning Default Value
1 MaxTxPower Maximum cell transmit 430, that is, 43 dBm
power
2 PCPICHPower PCPICH transmit power 330, that is, 33 dBm
Paging parameters
No. Parameter ID Parameter Meaning Default Value
1 DRXCycleLenCoef Paging cycle coefficient 6
Synchronization parameters
No. Parameter ID Parameter Meaning Default Value
1 NInsyncInd Number of successive 5
in-sync indications
2 NOutsyncInd Number of successive 50
out-of-sync indications
3 TRLFailure Radio link failure timer 50 (5 s)
duration
4 N312 N312 and T312 N312: D1
T312 T312: 6 s
5 N313 N313, N315, and T313 N313: D50
N315 N315: D1
T313 T313: 3 s
arameters
Current Value Relevant Command Level
6 Set or modify: SET FRC or MOD RNC
CNDOMAIN
Query: LST FRC or LST
CNDOMAIN
1 Set or modify: SET DPUCFGDAT
Query: LST DPUCFGDATA
parameters
Current Value Level
T300: D2000 (2 s) RNC
N300: 3
on parameters
Current Value Relevant Command Level
5 Cell
Set: ADD CELLSETUP
50
Query: LST CELL
50 (5 s)
Modify: MOD CELL
N312: D1 Set or Modify: SET IDLEMODET RNC
T312: 6 s Query: LST IDLEMODETIMER
N313: D50 Set or Modify: SET CONNMODET
N315: D1 Query: LST CONNMODETIMER
T313: 3 s
meters
Current Value Level
20s RNC
30s
2s
3
rameters
Current Value Level
10, that is, 1 hour RNC
ated parameters
Current Value Relevant Command Level
ARP1PRIORITY=GOLD,
ARP2PRIORITY=GOLD,
ARP3PRIORITY=GOLD,
ARP4PRIORITY=GOLD,
ARP5PRIORITY=GOLD,
ARP6PRIORITY=SILVER,
ARP7PRIORITY=SILVER,
ARP8PRIORITY=SILVER,
ARP9PRIORITY=SILVER, Set or modify: SET USERPRIOR
ARP10PRIORITY=SILVER,
ARP11PRIORITY=COPPER,
ARP12PRIORITY=COPPER
,
ARP13PRIORITY=COPPER
,
ARP14PRIORITY=COPPER
ARP
Query: LST USERPRIORITY
NONE
BACK
HS-DPCCH power control parameters
No. Parameter ID Parameter Meaning Default Value
1 ACKPO1 ACK power offset 24/15
ACKPO2 12\15
ACKPO3 9\15
2 ACKPO1forSHO ACK power offset in 24/15
ACKPO2forSHO multiple link set
ACKPO3forSHO
3 NACKPO1 NACK power offset 24/15
NACKPO2 12\15
NACKPO3 9\15
4 NACKPO1forSHO NACK power offset in 24/15
NACKPO2forSHO multiple link set
NACKPO3forSHO
5 ACKNACKReF1 ACK/NACK repeat factor 1
ACKNACKReF2 2
ACKNACKReF3 3
6 ACKNACKReFforSHO ACK/NACK repeat factor 1
in multiple link set
7 CQIPO CQI power offset in single 24/15
CQIPOforSHO and multiple RLS
8 CQIReF CQI Repeat Factor in 1
CQIReFforSHO Single and Multiple RLS
9 CQIFbCk CQI repeat period in D2 (2 ms)
CQIFbCkforSHO single and multiple RLS
24/15
12\15
9\15
24/15
1
2
3
1
24/15
D2 (2 ms)
Cell
ment parameters
Current Value Level
0 (0 s) RNC
ol algorithm parameters
Current Value Relevant Command Level
3840 Set: ADD NODEBALGOPARA NodeB
Query: LST NODEBALGOPARA
Modify: MOD NODEBALGOPARA
0 Cell
Set: ADD CELLCAC
70%
Query: LST CELLCAC
30%
Modify: MOD CELLCAC
64
BACK
Channel algorithm switches
No. Switch ID Switch Meaning Default Setting
1 AMR_TWO_CODCH_SWITCH Switch for two DCHs OFF
configuration by AMR
ALGORITHM
_REQUIRED:
Always reset
the MAC-hs no
matter the cells
in question are
in the same
NodeB or not.
ALGORITHM
_DEPEND_O
N_LCG: Reset
the MAC-hs
only when the
cells in
question are in
the different
local cell
group.
BACK
orithm switches
Current Value Description
OFF When it is checked, the AMR voice call with the bit rate
of 7.95 Kbit/s or less than that is allocated for two Co-
DCHs. Otherwise, it is allocated for three DCHs.
OFF When it is checked and the AMRC (AMR Control)
license is enabled, AMR control function is applied for
AMR users.
OFF When it is checked, it is allowed to decrease the
bandwidth of the BE services before handover happens.
It is recommended to open DCCC_SWITCH when
using this function.
ON When it is checked, dynamic channel reconfiguration
control algorithm is applied in the RNC.
ON When it is checked, the inner loop downlink power
control status is set to Active. Otherwise, it is set to
Inactive.
ON When it is checked, the downlink blind transport format
detection function is used for single SRB and AMR +
SRB bearers. Note that the UE is only required to
support blind transport format detection is the
restrictions in 3GPP 25.212 section 4.3.1 are fulfilled.
algorithm switches
Current Value Description
OFF When it is checked, the BLER target value comes from
the BLER target value of the AMR modes specified in
the AMRC parameter table. Otherwise, it comes from
the BLER target value specified in TYPRAB.
ON When it is checked, DPB (Downlink Power Balance)
algorithm is applied to RNC. Downlink power drift
among different RLs, which is caused by TPC bit error
or other reasons, could reduce the gain of soft handover.
DPB is mainly used to balance the downlink power of
different RLs for an UE in order to achieve the best
gain of soft handover.
ithm switches
Current Value Description
OFF When it is checked, UE RRC state transitions to
CELL_FACH for the DCCC algorithm of HSDPA
services are allowed in the RNC.
When the RAB on HS-DSCH is BE service,
the PS_BE_STATE_TRANS_SWITCH is required to
be checked simultaneously.
When the RAB on HS-DSCH is PS real-time
traffic, the PS_NON_BE_STATE_TRANS_SWITCH
is required to be checked simultaneously.
OFF When it is checked, PS streaming traffic can be mapped
to HS-DSCH when the downlink max bit rate is more
than or equal to the streaming on HSDPA threshold.
OFF When it is checked, the HSDPA (AM mode) flow
control function is applied in SRNC.
OFF When it is checked, UE RRC state transitions to
CELL_FACH for the DCCC algorithm of HSUPA
services are allowed in the RNC.
When the RAB on E-DCH is BE service, the
PS_BE_STATE_TRANS_SWITCH is required to
check simultaneously.
When the RAB on E-DCH is PS real-time
traffic, the PS_NON_BE_STATE_TRANS_SWITCH
is required to check simultaneously.
OFF When it is checked and the OLPC algorithm switch is
open, the RNC adjusts the E-DCH power offset
periodically.
OFF When it is checked, PS streaming traffic can be mapped
to E-DCH when the uplink max bit rate is more than or
equal to the streaming on HSUPA threshold.
OFF When it is checked, channel switch of HS-DSCH to
DCH is needed before adding neighbor RNC with
version lower than R5 cell to active set.
OFF When it is checked, the 2ms TTI could be applied to
HSUPA traffic.
OFF When it is checked, DCCC is available for the HSUPA
service.
OFF When it is checked, PS conversation traffic can be
mapped to HS-DSCH when the downlink max bit rate
is more than or equal to the conversation on HSDPA
threshold.
OFF When it is checked, PS conversation traffic can be
mapped to E-DCH when the uplink max bit rate is more
than or equal to the conversation on HSUPA threshold.
ithm switches
Current Value Description
OFF Only when this switch is on, can DRD be done if
combination service needs retry.
OFF This is the general DRD algorithm switch, only when
this switch is on, can the other DRD sub-switches be
on.
OFF Only when this switch is on, can DRD be done if
HSDPA service needs retry.
OFF Only when this switch is on, can DRD be done if RAB
DCCC flow needs retry.
OFF Only when this switch is on, can DRD be done if RAB
modify flow needs retry.
OFF When it is checked, DRD is triggered for the HSUPA
service that needs retry.
ON When it is checked, DRD is triggered for the RAB
setup process that needs retry.
ON After the intra-handover process is completed, when the
UE needs D2H retry for handover-triggering, the blind-
Ho DRD cell is allowed to select for D2H retry only if
the switch is on.
ON After the inter-handover process is completed, when the
UE needs D2H retry for handover-triggering, the blind-
Ho DRD cell is allowed to select for D2H retry only if
the switch is on.
Current Value
H
ON
OFF
OFF
OFF
OFF
OFF
ON
H
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ALGORITHM_
DEPEND_ON_L
CG
BACK
Transmission common parameters
No. Parameter ID Parameter Meaning Default Value
1 AAL2PATHT AAL2PATH type If there exists HSDPA service,
it needs to configure HSDPA
-
NRT Set: ADD IPPATH
Query: LST IPPATH or DSP IPPATH
ANY Modify: MOD IPPATH
BACK
HSDPA flow control parameters
No. Parameter ID Parameter Meaning Default Value
1 FlowControlAlgorithmS HSDPA bandwidth AUTO_ADJUST_
witch adjustment switch FLOW_CTRLpath
2 FrameDiscardRateThresh Frame discard rate 0.10%
old threshold on Iub interface
3 DlTrDelayJitterThldBase Time delay threshold 4 (8 ms)
ng algorithm parameters
Current Value Relevant Command
0 Set the parameter through SET MACHSPARA
(BTS3812E, BTS3812A, BTS3812AE,
BBU3806, BBU3806C), and query it through
LST MACHSPARA (BTS3812E, BTS3812A,
BTS3812AE, BBU3806, BBU3806C).
EPF
5 (5%)
0 (adaptive power control
based on CQI)
28 (‿dB), step is 0.25
10 (1%), step is 0.25
OPEN
OPEN
OPEN
0 (no filter)
See the table Set the parameter through SET
MACHSSPIPARA (BTS3812E, BTS3812A,
See the table BTS3812AE, BBU3806, BBU3806C), and
query it through LST MACHSSPIPARA
See the table
(BTS3812E, BTS3812A, BTS3812AE,
BBU3806, BBU3806C).
Cell
ment parameters
Current Value Relevant Command
2km On the NodeB LMT, set the parameter through
MOD LOCELL (BTS3812E, BTS3812A,
BTS3812AE, BBU3806, BBU3806C), and
query it through LST LOCELL (BTS3812E,
BTS3812A, BTS3812AE, BBU3806,
BBU3806C).
0m