Professional Documents
Culture Documents
Sikagard®-63 N: Product Data Sheet
Sikagard®-63 N: Product Data Sheet
Sikagard®-63 N: Product Data Sheet
Sikagard®-63 N
2-PART EPOXY PROTECTIVE COATING
CHARACTERISTICS / ADVANTAGES
▪ Solvent free
▪ Good mechanical and chemical resistance
▪ High build
▪ Impervious to liquids
▪ Easy to mix and to apply
PRODUCT INFORMATION
Chemical Base Epoxy resin
Packaging Part A 8.70 kg drums
Part B 1.3 kg drums
1/3
Density Mixed resin approx. 1.35 kg/l (EN ISO 2811-1)
Density values determined at +23 °C
Solid Content ~100 %
TECHNICAL INFORMATION
Tensile Adhesion Strength > 1.5 N/mm² to concrete (ISO 4624)
>15 N/mm² to steel (EN 24624)
>10 N/mm2 to aluminium (EN 24624)
Chemical Resistance For further information please contact Sika Technical Service.
Thermal Resistance Exposure Dry heat
Permanent +40 °C
max. 3 days +60 °C
Diffusion Resistance to Water Vapour µH2O ~ 100 000 (EN ISO 7783-1)
APPLICATION INFORMATION
Mixing Ratio Part A : Part B = 83 : 17 by weight
Consumption ~0.15 kg/m² per layer
Layer Thickness ~0.1 mm per layer
Ambient Air Temperature +10 °C min. / +30 °C max.
Relative Air Humidity < 80 %
Substrate Temperature +10 °C min. / +40 °C max.
Minimum 3 °C above dew point, beware of condensation
Pot Life Temperature Time
+10 °C ~30 min
+20 °C ~20 min
+30 °C ~10 min
2/3
entrapment. To ensure proper mixing pour material in- ECOLOGY, HEALTH AND SAFETY
to a clean container and stir again.
For information and advice on the safe handling, stor-
APPLICATION age and disposal of chemical products, users shall refer
Apply by brush, roller or airless spray. to the most recent Safety Data Sheet (SDS) containing
physical, ecological, toxicological and other safety-re-
CLEANING OF TOOLS lated data.
Clean all tools with Thinner C immediately after use. DIRECTIVE 2004/42/CE - LIMITATION OF EMISSIONS
Hardened and/or cured material can only be removed OF VOC
mechanically.
According to the EU-Directive 2004/42, the maximum
allowed content of VOC (Product category IIA / j type
LIMITATIONS sb) is 500 g/l (Limits 2010) for the ready to use
▪ Do not apply Sikagard®-63 N on moist substrates. product. The maximum content of Sikagard®-63 N is
▪ Sag resistance on vertical surface is < 100 μm. <500 g/l VOC for the ready to use product.
▪ Sikagard®-63 N cannot be used to produce glass fibre
reinforced linings. LEGAL NOTES
▪ Freshly applied Sikagard®-63 N must be protected
from rain, condensation and water for at least 24 The information, and, in particular, the recommenda-
hours. tions relating to the application and end-use of Sika
▪ For exact colour matching ensure using material from products, are given in good faith based on Sika's cur-
the same control batch numbers. rent knowledge and experience of the products when
properly stored, handled and applied under normal
conditions in accordance with Sika's recommenda-
BASIS OF PRODUCT DATA tions. In practice, the differences in materials, sub-
All technical data stated in this Product Data Sheet are strates and actual site conditions are such that no war-
based on laboratory tests. Actual measured data may ranty in respect of merchantability or of fitness for a
vary due to circumstances beyond our control. particular purpose, nor any liability arising out of any
legal relationship whatsoever, can be inferred either
from this information, or from any written recom-
LOCAL RESTRICTIONS mendations, or from any other advice offered. The
Please note that as a result of specific local regula- user of the product must test the product’s suitability
tions the declared data for this product may vary from for the intended application and purpose. Sika re-
country to country. Please consult the local Product serves the right to change the properties of its
Data Sheet for the exact product data. products. The proprietary rights of third parties must
be observed. All orders are accepted subject to our
current terms of sale and delivery. Users must always
refer to the most recent issue of the local Product Data
Sheet for the product concerned, copies of which will
be supplied on request.
Sikagard-63N-en-IN-(11-2018)-2-1.pdf
3/3