Professional Documents
Culture Documents
74LVC257A: Quad 2-Input Multiplexer With 5 Volt Tolerant Inputs/outputs (3-State)
74LVC257A: Quad 2-Input Multiplexer With 5 Volt Tolerant Inputs/outputs (3-State)
74LVC257A
Quad 2-input multiplexer with 5 Volt
tolerant inputs/outputs (3-State)
Philips Semiconductors Product specification
FEATURES DESCRIPTION
• Wide supply voltage range of 1.2 to 3.6 V The 74LVC257A is a high-performance, low-power, low-voltage,
Si-gate CMOS device and superior to most advanced CMOS
• In accordance with JEDEC standard no. 8-1A compatible TTL families.
• CMOS lower power consumption Inputs can be driven from either 3.3V or 5.0V devices. In 3-State
• Direct interface with TTL levels operation, outputs can handle 5V. This feature allows the use of
these devices as translators in a mixed 3.3V/5V environment.
• Output drive capability 50 transmission lines at 85°C The 74LVC257A is a quad 2-input multiplexer with 3-state outputs,
• 5 Volt tolerant inputs/outputs, for interfacing with 5 Volt logic which select 4 bits of data from two sources and are controlled by a
common data select input (S). The data inputs from source 0 (1l0 to
4l0) are selected when input S is LOW and the data inputs from
source 1 (1l1 to 4l1) are selected when S in HIGH. Data appears at the
outputs (1Y to 4Y) in true (non-inverting) form from the selected inputs.
The 74LVC257A is the logic implementation of a 4-pole, 2-position
switch, where the position of the switch is determined by the logic
levels applied to S. The outputs are forced to a high impedance
OFF-state when OE is HIGH.
ORDERING INFORMATION
PACKAGES TEMPERATURE RANGE OUTSIDE NORTH AMERICA NORTH AMERICA PKG. DWG. #
S 1 16 VCC 2 3 5 6 11 10 14 13
1I0 2 15 OE
1I0 11I 2I0 2I1 3I0 3I1 4I0 4I1
1I1 3 14 4l0
IY 4 13 4l1 1 S
2l0 5 12 15 OE
4Y
2l1 6 11 3l0 1Y 2Y 3Y 4Y
2Y 7 10 3l1
GND 8 9 3Y 4 7 9 12
SV00637
SV00636
OE
SV00638
S
FUNCTIONAL DIAGRAM SV00640
2 1I0
1Y 4
3 1I1
5 2I0
2Y 7
6 2I1
3–STATE
SELECTOR MULTIPLEXER
11 3I0 OUTPUTS
3Y 9
10 3I1
14 4I0
4Y 12
13 4I1
S OE
1 15
SV00639
1998 Jul 29 3
Philips Semiconductors Product specification
1998 Jul 29 4
Philips Semiconductors Product specification
DC ELECTRICAL CHARACTERISTICS
Over recommended operating conditions voltages are referenced to GND (ground = 0V)
LIMITS
SYMBOL PARAMETER TEST CONDITIONS Temp = -40°C to +85°C UNIT
MIN TYP1 MAX
VCC = 1.2V VCC
VIH HIGH level Input voltage V
VCC = 2.7 to 3.6V 2.0
VCC = 1.2V GND
VIL LOW level Input voltage V
VCC = 2.7 to 3.6V 0.8
VCC = 2.7V; VI = VIH or VIL; IO = –12mA VCC*0.5
VCC = 3.0V; VI = VIH or VIL; IO = –100µA VCC*0.2 VCC
VOH
O HIGH level output voltage V
VCC = 3.0V; VI = VIH or VIL; IO = –18mA VCC*0.6
VCC = 3.0V; VI = VIH or VIL; IO = –24mA VCC*0.8
VCC = 2.7V; VI = VIH or VIL; IO = 12mA 0.40
VOL LOW level output voltage VCC = 3.0V; VI = VIH or VIL; IO = 100µA GND 0.20 V
VCC = 3.0V; VI = VIH or VIL; IO = 24mA 0.55
IOZ 3-State output OFF-state current VCC = 3.6V; VI = VIH or VIL; VO = VCC or GND 0.1 "5 µA
IOFF Power off leakage current VCC = 0.0V; VI or VO = 5.5V 0.1 "10 µA
ICC Quiescent supply current VCC = 3.6V; VI = VCC or GND; IO = 0 0.1 10 µA
Additional quiescent supply current per
∆ICC VCC = 2.7V to 3.6V; VI = VCC –0.6V; IO = 0 5 500 µA
input pin
NOTES:
1. All typical values are at VCC = 3.3V and Tamb = 25°C.
AC CHARACTERISTICS
GND = 0 V; tr = tf v 2.5 ns; CL = 50 pF; RL = 500; Tamb = –40C to +85C
LIMITS
SYMBOL PARAMETER WAVEFORM VCC = 3.3V ±0.3V VCC = 2.7V VCC = 1.2V UNIT
MIN TYP1 MAX MIN TYP1 MAX TYP
Propagation delay
tPHL/tPLH nl0 to nY Figures 1, 3 1.5 3.9 5.1 1.5 3.3 6.1 11 ns
nl1 to nY
Propagation delay
tPHL/tPLH Figures 1, 3 1.5 3.5 6.4 1.5 4.3 7.5 14 ns
S to nY
3-state output enable time
tPZH/tPZL Figures 2, 3 1.5 3.7 6.5 1.5 4.6 7.5 15 ns
OE to nY
3-state output disable time
tPHZ/tPLZ Figures 2, 3 1.5 3.2 5.2 1.5 3.5 6.2 12 ns
OE to nY
NOTE:
1. These typical values are at VCC = 3.3V and Tamb = 25°C.
1998 Jul 29 5
Philips Semiconductors Product specification
VOL and VOH are the typical output voltage drop that occur with the RT CL 50pF
500Ω
output load.
VCC
Test S1
S, nI0, nI1 VM
VCC VI tPLH/tPHL Open
INPUTS
GND 2.7V VCC tPLZ/tPZL 2 x VCC
VOH SY00003
VOL
SV00641
VI
OE INPUT VM
GND
tPLZ tPZL
VCC
OUTPUT
LOW-to-OFF VM
OFF-to-LOW
VX
VOL
tPZH
tPHZ
VOH
VY
OUTPUT
HIGH-to-OFF VM
OFF-to-HIGH
GND
outputs outputs outputs
enabled disabled enabled
SV00642
1998 Jul 29 6
Philips Semiconductors Product specification
SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1
1998 Jul 29 7
Philips Semiconductors Product specification
SSOP16: plastic shrink small outline package; 16 leads; body width 5.3 mm SOT338-1
1998 Jul 29 8
Philips Semiconductors Product specification
TSSOP16: plastic thin shrink small outline package; 16 leads; body width 4.4 mm SOT403-1
1998 Jul 29 9
Philips Semiconductors Product specification
Objective Development This data sheet contains the design target or goal specifications for product development.
specification Specification may change in any manner without notice.
Preliminary Qualification This data sheet contains preliminary data, and supplementary data will be published at a later date.
specification Philips Semiconductors reserves the right to make chages at any time without notice in order to
improve design and supply the best possible product.
Product Production This data sheet contains final specifications. Philips Semiconductors reserves the right to make
specification changes at any time without notice in order to improve design and supply the best possible product.
[1] Please consult the most recently issued datasheet before initiating or completing a design.
Definitions
Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For
detailed information see the relevant data sheet or data handbook.
Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one
or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or
at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended
periods may affect device reliability.
Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips
Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or
modification.
Disclaimers
Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can
reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications
do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application.
Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard
cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no
responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these
products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified.
yyyy mmm dd 10