Ata 27 Flight Controls and Ata 29 Hydraulic

You might also like

Download as docx, pdf, or txt
Download as docx, pdf, or txt
You are on page 1of 4

ATA 27 FLIGHT CONTROLS

1. Function of spring box in aileron is :


a) It connects the trim actuator output lever to the aileron control run
b) Assists the movement of ailerons back to neutral
c) Both a and b is correct
d) Only b is correct.

2. What is the full deflection of aileron when flaps are retracted


a) -17 degree , + 26 degree
b) -16 degree, + 27 degree
c) -25 degree, + 18 degree
d) -18 degree, + 27 degree

3. Trimming of aileron
a) Trimming is done only manually
b) Trimming is done only electrically
c) Trimming is done both manually and electrically by trim actuator

4. Trimming of rudder
a) Rudder trim is done electrically
b) Rudder trim is done manually
c) Both electrically and manually by rudder trim actuator

5. Rudder pedal adjustment handle is located


a) At the rudder pedal
b) Below the instrument panel
c) At the centre pedestal
d) Below cockpit seat

6. Teleflex assembly for rudder trim runs through


a) Fuselage underfloor area
b) LH sidewall of fuselage
c) Through Ceiling of the fuselage
d) RH sidewall of fuselage

7. Elevator trim can be controlled by


a) Elevator trim switch on the centre pedestal
b) Elevator cannot be trimmed
c) Elevator can be control by pith servo in autopilot
d) Both b and c

8. Wing tip brakes are located


a) Inboard of the flap
b) Outboard of the flap
c) Near the flap drive unit

9. Flap control switch located at:


a) Overhead panel F/O side
b) Overhead panel Captain side
c) On the centre pedestal
d) In the instrument panel

10. Brakes in the asymmetry unit is released


a) When the relay energized and electrical power is supplied
b) When the relay is denergized and electrical power is cuttoff
c) Brakes in the asymmetry unit cannot be released

29- Hydraulic

11. Hydraulic power pack located at


a) Rear side of the RH landing gear nacelle
b) Rear section of the left landing gear nacelle
c) In the landing gear bay

12. The type of hydraulic pump used in dornier 228 is


a) Gerotor pump
b) Axial piston pump
c) Variable delivery piston type pump
d) Fixed delivery piston type pump

13. The delivery rate of pump is :


a) 9 l/min
b) 8 l/min
c) 8.5 l/min
d) 8.25l/min

14. The maximum pressure of the pump delivered is


a) 205 bar
b) 207 bar
c) 206 bar

15. MTCS
a) A check valve is fitted downstream of the landing gear circuit in the pressure line for
wheel brakes
b) A check valve is fitted downstream of the landing gear circuit in pressure line for steering
system
c) Both a and b is correct
d) Only b is correct

16. How many stages of hydraulic self regulated power system


a) 3 stages
b) 4 stage
c) 6 stage

17. What is the maximum current rating of electrically driven hydraulic pump
a) 120 AMPS
b) 130 AMPS
c) 140 AMPS

18. Hydraulic pressure switch is located in


a) The power pack
b) RH side landing gear nacelle
c) On the floor structure in frame 11

19. Hydraulic pump is automatically switched off


a) At every up selection of the L/G lever
b) When all the L/G are up and locked
c) When only the nose gear uplock is locked
d) Both a and b

20. Parking brake accumulator is located in


a) LH landing gear nacelle area
b) RH landing gear nacelle area
c) In the landing gear bay

You might also like