Professional Documents
Culture Documents
C28xx colorTV Sanyo
C28xx colorTV Sanyo
Service Manual
Chassis: EH1-A
Model:
For further technical information, please refer to the training manual EH1 chassis, ref. No. TI520013. Give complete "SERVICE REF. NO." for parts order or servicing, it is shown on the rating sheet on the cabinet back of the TV set. Note This TV receiver will not work properly in foreign countries where the television transmission system and power source differ from the design specifications. Refer to the specifications for the design specifications
Contents Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Circuit description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-7 Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Service adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-13 Component locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-20 Special functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Waveforms & voltages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22-27 Service parts lists Schematic diagram
SAFETY PRECAUTION
1: An isolation transformer should be connected in the power line between the receiver and the AC line when a service is performed on the primary of the converter transformer of the set. 2: Comply with all caution and safety-related notes provided on the cabinet back, inside the cabinet, on the chassis or the picture tube. 3: When replacing a chassis in the cabinet, always be certain that all the protective devices are installed properly, such as, control knobs, adjustment covers or shields, barriers, isolation resistor-capacitor networks etc.Before returning any television to the customer, the service technician must be sure that it is completely safe to operate without danger of electrical shock.
X-RADIATION PRECAUTION
The primary source of X-RADIATION in the television receiver is the picture tube. The picture tube is specially constructed to limit X-RADIATION emissions. For continued X-RADIATION protection, the replacement tube must be the same type as the original including suffix letter. Excessive high voltage may produce potentially hazardous X-RADIATION. To avoid such hazards, the high voltage must be maintained within specified limit. Refer to this service manual, high voltage adjustment for specific high voltage limit. If high voltage exceeds specified limits, take necessary corrective action. Carefully follow the instructions for +B1 volt power supply adjustment, and high voltage adjustment to maintain the high voltage within the specified limits.
Outline
3D surround processor
AV4(Front) L, R L, R L, R
(Scart)
SIF carrier
CIRCUIT DESCRIPTION
Speakers
L, R
Tuner IF stage
Y 2Y R G B R-Y B-Y H/V sync 2B-Y 2R-Y
CRT
Y/CVBS
AV1
AV selector
HD VD
AV2
Video output
This is a diagram for all models and therefore differs slightly from the actual block diagram.
-3H-Centring
AV3
AV4
DY
H.V
AV mode
System Control
V-Centring H-Drive
VD
V-drive
Vertical output
RGB
High-voltage
These signals are again input to the audio processor IC, and are controlled in volume, bass, treble, balance and sound mute by the CPU via I2C bus. The controlled audio signals are supplied to the audio output circuit to drive the loudspeakers.
AV1
AV2
AV3
AV4(Front)
AV2-BLK
TV-out
Q1204 Monitor-out
AV2-R,G,B
Q105
8 7 IF
CVBS
21 Q112 Q1231
40 37 45
1 2 3 4 18 19 20 21 11 17
R-Y B-Y
16 14 12 11 R,G,B,BLK
2 3 4 15 6 7 8
5 14
R,G,B
43
26 14 13 12 30
IC206
V-sync H-sync 13 11 BLK 10 12
IC207
11 9 10 12 Q831 Q832 Q833
AV Selector
R-Y B-Y
IC801
CVBS 23 24 Q211 Q212 CPU 35 34 33 32 BLK RGB R-Y B-Y Y Q213 4.43MHz osc.
IC711
Q721
3 5 3 5
IC721
Q731
IC731
8
IK
BACK BOARD
AV Selector Circuit
IC3800 A2 Stereo Sound Demo.
5.5MHz 6 5 AF1 22 Q107 Main R 7 8 Q3483 Q3484 I2C BUS 1 8 7 14 L 16 15
Tu X102
IC101 IF
R 1 3 32 28
SCART L R L FRONT AV
AF2
13 20 1
30
49 50 29
16 17 18 L R
I2C
BUS
15
From CPU
14
11
Q3432
R 9 L 10
R L L 24 23 R
L 13
23
Q3431
IC3521 Equaliser
Q836
Tu
X103 SAW
IC1200
V
IC202
IC204
R-Y B-Y
IC101
RGB SW 13 12 11 10
IC201
Q681 RC5V
IC802
24LC04
IC2341
MC74HC74AF
CXD2018QP CXD2018QP
IC2351 IC2351
8
IC2361
LA6358M
CPU
21
16
8
LA6458M
QXXAV8079
UPC1377C
24V
IC001
TA8216H
LA6393M
CXA1315P
LA6458M
LA6458M
39
IC207
M74L532P
H/V sync.det.
4 -12V
IC675
8V
14 5V Video Sharpness 59 8 16 8 8
B5V
IC2201
AN5390FBS
IC2202
TC7W04F
IC2203
TC74HC123AF
IC2205
TC7WH74FU
IC2206
LA6393M
19
16 Matrix& controller
IC2101
AN5395FBP
IC2102
CXA1315P
IC677 D5V
5V 14 14,26 8bit A/D converter 30,35 51,62 IC7201
TLC5733IPM
73
Logic ICs
IC205
MC74HC74AN
IC7301
5V
IC7213
CXD2000Q
14
IC206
MC74HC04AN
IC7214
30,32 42,43
QXXAAC2138
IC7203 IC7204 IC7205 IC7206 IC7207 IC7208 IC7209 IC7211 IC7212 IC7215 IC7221 IC7222 IC7223
DOUBLE SCAN CONVERTER BOARD
D/A converter
14
3,26,36
IC3401
9V
TDA9840
IC3800
TDA9821
IC3451
SAA7283
A2 stereo decoder
IC678
12V 9 9
C9V
44 9V
AV selector
IC1200
CXA1855S
BACK BORAD
Tuner
IC101
LA7577N
IC350
LA7210
IF demodulator 15V
IC673 A8V
8V 7 8 1 5V Sound controller 12V 6 1, 9
IC203
LA6393
IC201
TDA8601
IC3431
TDA9860
IC204
TDA4665
1H delay
Video/chroma/def. 24 4
RGB selector
IC3531
MM1369AD
IC3521
M5228P
IC652 A12V
12V
IC711
TDA6111Q
IC721
TDA6111Q
IC731
TDA6111Q
CRT BOARD
-12V
-12V 33V
Tuning voltage
T403
137V
65V
35V
200V
CRT Heater
T402 7 15V
V-Output
IC501
LA7846N
High Voltage
-15V
-12V
12V
IC801
IC361
IC2311
IC2331
IC2371
IC2381
IC2391
TUNER
TUNING IF-AGC
TU
Q801
1 52 51
AFT-S I2C BUS SDA I2C BUS SCL SOUND MUTE RC SIGNAL SYNC IDENT AKB/2V
SYNC ON MUTE ON VL
SDA-NVM SCL-NVM
Q111
Q104
Q604
VL
VH
Q103/Q802
BAND1
2 3 50
I2C BUS Control
System control
VH
U
Q102/Q803 BAND3
BAND2
Q101/Q804
4 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 23 24 25 26 30 29 28 27
FRAME VIDEO MUTE V-SYNC H-SYNC BLANKING (OSD) RED (OSD) GREEN (OSD) BLUE (OSD) X'TAL OSC for CPU RESET
IC801 CPU
IC001 AUDIO OUT IC350 SYNC ID
5 6
SIF SW L/L'
7 8 9 10 11 12 13
STANDBY
VIDEO-in
KEY SWITCHES
-7ON
FRONT AV SW.
14 15 16
17 18 19 20 21 22
D615
60Hz ON ON
To Scan Converter
Y R-Y B-Y
MUTE
VIDEO CONTROLLER
DISASSEMBLY
CABINET BACK DISASSEMBLY
(A) 1. Remove 10 screws(A) and 4 screews(B) 2. Pull out the cabinet back.
(A)
(A)
(A)
(A)
(A) (A)
(A)
(A)
(D)
(C)
SERVICE ADJUSTMENTS
Note: Some items of the service adjustments for this chassis are controlled by the CPU, IC801, and the adjustments are carried out by using the RC handset.
Adjustments Stereo separation adjustment Vertical Centring Vertical Height Horizontal Centring Horizontal Width White Balance DCS Gain Auto Setup Option setting
Service Mode Item 000, Item 001 Item 005 Item 006 Item 009 Item 010 Item 034, Item 035 Item 057 Item 069
ADJUST DATA Item +000 K1 +001 K2 +003 STID +001 -006 +000 service data
+ To select the adjustment item, use the Prog+ or Prog- button. The selected item is indicated in red. + To change the service data, use the Level - or Level + button. + The data which is set in the service mode is stored into the memory IC automatically.
+063 +064 +065 +066 +067 +068 +069 +070 +071 +072
Xtal System TintTDA YDelyPA YDelyNT YDelySE Country WideOpt TxBrit TxCont
+002 +224 +016 +010 +010 +010 +001 +001 +040 +062
Fixed Fixed Fixed Fixed Fixed Fixed ADJSTBL Fixed Fixed Fixed
Xtal setting, 0:3.58+3.58, 1:3.58, 2:4.43, 3:4.43+3.58 Sub address setting 01 of TDA9134 Tint setting of TDA9143 Y/C phase setting for PAL (sub address setting 18 of TDA9143) Y/C phase setting for NTSC (sub address setting 18 of TDA9143) Y/C phase setting for SECAM (sub address setting 18 of TDA9143) 0: auto search 1: ATS 0: 16:9 mode off 1: 16:9 mode on Black level setting of teletext mode Contrast setting of teletext
Notes: + The initial value that the CPU writes down the CPU ROM data to the memory when replaced the memory IC. TV set does not operate correctly with this initial value. + The items which are shown with fixed in the status column in the table above are preset by factory as standard. So do not change value otherwise the set may not operate properly. + The items which are shown with RECOMD are normally not requied for re-adjustment but it may change the value to implove the performance. + The items which are shown with ADJSTBL should be re-adjusted following steps.
SERVICE ADJUSTMENTS-1
After replacing the memory IC, IC802, folllowing service adjustments must be carried out. STEREO SEPARATION ADJUSTMENT 1. Enter to the service mode. 2. Select item 000 and set data to +000, select item 001 and set data to -006. WHITE BALANCE ADJUSTMENT 1. Receive white pattern. 2. Enter to the service mode. 3. Adjust white balance using the following items, Item 034 R drive adjustment Item 035 B drive adjustment DCS GAIN ADJUSTMENT 1. Enter to the service mode. 2. Select item 059 and set data to 100.
VERTICAL CENTRING ADJUSTMENT 1. Receive circular pattern. 2. Enter to the service mode. 3. Select Item 5 and adjust the vertical centre.
VERTICAL HEIGHT ADJUSTMENT 1. Receive circular pattern. 2. Enter to the service mode. 3. Select Item 6 and adjust the vertical height.
AUTO SETUP OPTION SETTING 1. Enter to the service mode. 2. Select item 057 and set data as follows; Value +000 : Auto search mode for UK and Ireland Value +001 : ATS mode for W. Europe countries.
HORIZONTAL CENTRING ADJUSTMENT 1. Receive circular pattern. 2. Enter to the service mode. 3. Select Item 9 and adjust the horizontal centre.
HORIZONTAL WIDTH ADJUSTMENT 1. Receive circular pattern. 2. Enter to the service mode. 3. Select Item 10 and adjust the horizontal width.
SERVICE ADJUSTMENTS-2
Please refer to the Component Locations for the adjustments and test points. VCO ADJUSTMENT 1. Receive the circular pattern. 2. Adjust the picture to obtain the best picture by using T103. VIDEO AMPLITUDE ADJUSTMENT(Europe only) 1. Receive the PAL colour bar pattern. 2. Connect oscilloscope between JT1201(+) and JT1201E(-) on the back board. 3. Adjust the video amplitude to be 1.0Vp-p0.05V by using VR1201 on the back board.
100% white level
B1 POWER SUPPLY ADJUSTMENT 1. Set VR641 to be mechanical centre before pressing the main switch. 2. Receive the circular pattern. 3. Set brightness and contrast controls to normal. 4. Connect digital V-meter to TP453 on the sub/def. board. 5. Adjust voltage to be 1370.5VDC by using VR641 on the sub/def. board.
1.0Vp-p
AFT ADJUSTMENT 1. Receive the clearest station. 2. Adjust AFT to obtain the best picture by using T102.
DOUBLE SCAN ADJUSTMENT Receive the PAL colour bar pattern. Adjustment points are on the double scan borad. [PLL ADJUSTMENT] 1. Connect oscilloscope between C7226-(TPOSC)(+) and GND(-). 2. Adjust voltage to be 2.5VDC by using T7201.
AGC ADJUSTMENT NOTE: Do not attempt this adjustment with weak signal. 1. Receive the clearest station. 2. Set AGC VR(VR101) in direction which causes snow noise to appear, then in the opposite direction until snow noise just disappears.
2.5VDC
FM DETECTOR ADJUSTMENT(UK/Ireland only) 1. Receive the monaural station of system I. 2. Connect voltmetre between TPC and TPE. 3. Adjust the voltage to be 6.00.2VDC by using T101.
DC=0
PILOT ADJUSTMENT(Europe only) 1. Receive the A2 stereo signal Carrier :5.5MHz + 5.74MHz Deviation :27kHz 2. Connect oscilloscope between TP34A(pin 5 of IC3401) and TP34E. 3. Adjust the amplitude to be maximum by using T3401.
[CLAMP ADJUSTMENT] 1. Connect voltmetre between pin 52 of IC7201(+) and pin 48 of IC7201(-). 2. Adjust voltage to be 2.0VDC by using VR7201. [OUTPUT LEVEL ADJUSTMENT-Y] 1. Connect oscilloscope between pin 6 of K73C(+) and GND(-). 2. Adjust the Y signal amplitude to be 0.7Vp-p by using VR7351.
0.7Vp-p
[OUTPUT LEVEL ADJUSTMENT-R-Y] 1. Connect oscilloscope between pin 10 of K73C(+) and GND(-). 2. Adjust the R-Y signal amplitude to be 0.7Vp-p by using VR7352.
FOCUS ADJUSTMENT By using FOCUS VR, adjust focus control for well defined scanning lines.
0.7Vp-p
[OUTPUT LEVEL ADJUSTMENT-B-Y] 1. Connect oscilloscope between pin 8 of K73C(+) and GND(-). 2. Adjust the B-Y signal amplitude to be 0.7Vp-p by using VR7353.
0.7Vp-p
SCREEN ADJUSTMENT 1. Receive the PAL colour bar pattern. 2. Connect oscilloscope between JTP47G(+) and JTP47E(-) on the CRT unit. 3. Adjust colour control to minimum, brightness to centre and contrast to minimum. 4. Adjust the black level to be 165VDC5V by using SCREEN VR on the FBT. Black level
165VDC
DC=0
HIGH VOLTAGE CONFIRMATION 1. Receive the white pattern. 2. Set brightness and contrast controls to maximum. 3. Connect digital V-meter between TP451 and TP452, and high voltage meter to CRT anode. 4. Confirm high voltage to be 28.5 1 KV at beam current 1.8, and less than 32.5 KV at 0 beam current. -13Service Manual EH1 chassis
K2K K2K
K2L K2L
TPA
IC678
T102
VR101 AGC
IC3531 IC3531
AGC AFT
TPC
T101
IC101 IC101
FM
PILOT
T3401
TP34E IC674
IC350
IC673
IC802
IC201 IC201
IC202 IC202
IC203
COMPONENT LOCATIONS
IC675
IC676
IC207
IC206
K2PL K2PL
K2Y K2Y
-14-
TP34A
VCO
K2W K2W
T103
Q103 Q101 Q102 Q104 A101 IC3451 Q114 Q3483 Q3412 IC101 IC3800 Q111 Q131 Q107 IC3401 Q115 Q112
Q3431
IC001
IC3431
IC3521 Q3484
Q3432
IC3531
IC3500
Q873
Q211 Q213
Q851
Q214
IC801
IC206
IC205
Q804
Q802
Q803
-15-
Q461
+B VOLT
IC653 Q572 Q641 Q661 Q556
Q472
TP451
Q471
SCREEN
Q402
LIVE SIDE
Q612
-16-
IC2331
IC2361 Q361
IC2351
Q364
IC2381
IC2101
IC2201
Q2108
Q2107
K20PL
K20VI
K20PO
IC2101
IC7215
IC7212
PLL
Q7359 Q7355
CLAMP
Q7338 Q7308 Q7301 Q7307 Q7306
Q7304
Q7360 Q7356
B-Y Q7352 Y
R-Y VR7353
VR7352
VR7351 IC7301
K73B
K73C
K73A
IC7205 IC7209
Q7201
IC7202
IC7208 IC7211
K1002
IC1201 Q1201 Q1202 Q1204 Q1208 Q1207 Q1002 Q1205 Q1206 JT1201E JT1201 Q1232 Q1001 K10Y Q1203
K1003
Q1231
VIDEO AMP
K10W
IC731 R-OUT
JTP47G Q721
Q711 JTP47E
K701
Q703 Q702
Q701
Q731
Prog+ Prog-
Vol+
F/M
PT SYS
A1901
Q1111
Q1131
Q1121
-20-
SPECIAL FUNCTIONS
This TV set allows you to set up the following special functions. s Maximum volume setting and prohibition of presetting ITEM-1 Sets the current volume as the maximum volume level and prohibition of presetting. SET 0 NO SET 1 YES s Start up programme position ITEM-2 Presets the programme position when the set is switched on. SET 0 Last programme position start SET 1 Programme position "1" start SET 2 Programme position "2" start SET 3 Programme position "3" start SET 4 Programme position "4" start SET 5 Programme position "5" start SET 6 Programme position "6" start SET 7 Programme position "7" start SET 8 Programme position "8" start SET 9 "AV1" start
ITEM-1
SET->0
SETTING PROCEDURE
1 2 3 4
Press and hold the button on the Remote control handset and then press the Pv button on the TV set. To select the "ITEM" number, press the F the remote control handset. To select the "SET" number,press the button repeatedly. button on or
i The setting conditions of all items can be confirmed. i Special functions are not cancelled if the TV set is switched off or the mains disconnected. i This mode is not available whilst in the AV mode.
4 4 4
0V 0V 0V
5 5 5
6 6 6
7 7 7
8 8 8
9 9 9
E C B
E C B
E C B
DC=0V
DC=0V
DC=0V
DC=0V
DC=0V
DC=0V
4 13 22 4 13
5 14 23 5 14
6 15 24 6 15
7 16
0V 11.3V
8 17
3.7V 4.6V
9 18
12.1V 5.3V
7 16
2.3V 0.4V
5.1V
0V
2 11 20 29 2 2 11 2 11 2 11 2 11 2
3 12 21 30 3 3 12 3 12 3 12 3 12 3
2.4V 3.3V 5.0V 2.5V 0V 0V 2.9V 0.2V 0V 0.2V 5.0V 0.1V 0V 9.4V
4 13 22 31 4 4 13 4 13 4 13 4 13 4
5 14 23 32 5 5 14 5 14 5 14 5 14 5
4.1V 2.5V 0.1V 0V 1.1V 7.1V 1.4V 0V 5.1V 4.8V 5.1V 4.8V 5.1V 0V
6 15 24
3.8V 0V 4.0V
7 16 25
8.0V 2.5V 0V
8 17 26
9 18 27
0V 0.7V 0V
6 6 15 6
3.2V 0V 0V 5.0V
7 7 16 7
8 8 8
0.2V
0V
5.0V
0V
0V
0V
0.9
1.2V
IC350 1 9.9V 10 0V IC671 1 14.9V IC674 1 15.2V IC678 1 12.1V IC801 1 0.6V 10 0.6V 19 5.1V 28 0V 37 0.1V 46 0V IC802 1 0V
9.6V
0.3V
10.8V
12.1V
2 2 2 2 11 20 29 38 47 2 2 11 20 2 11 20 29 2 11 20 29 38 47
0V 0V 0V 0V 3.7V 3.3V 5.0V 5.0V 5.0V 0V 3.4V 2.5V 4.0V 0.1V 4.0V 4.0V 4.0V 2.4V 2.5V 2.5V 2.5V 5.1V 4.7V
3 3 3 3 12 21 30 39 48 3 3 12
2 2
0V 0V
3 3
5.1V 5.1V
2 2
0V 0V
3 3
8.0V 9.1V
4 13 22 31 40 49 4 4 13
5 14 23 32 41 50 5 5 14
6 15 24 33 42 51 6 6 15
7 16 25 34 43 52 7 7 16
8 17 26 35 44
9 18 27 36 45
8 8 17
IC3401 1 3.8V 10 2.5V 19 3.4V IC3431 1 4.1V 10 4.0V 19 4.0V 28 4.0V IC3451 1 0V 10 0V 19 0V 28 2.5V 37 0V 46 5.0V
3 12 21 30 3 12 21 30 39 48
4 13 22 31 4 13 22 31 40 49
5 14 23 32 5 14 23 32 41 50
6 15 24
7 16 25
4.0V 4.0V 0V
8 17 26
0V 3.7V 4.0V
9 18 27
6 15 24 33 42 51
7 16 25 34 43 52
8 17 26 35 44
9 18 27 36 45
IC3521 1 4.5V 10 4.5V IC3531 1 4.5V 10 0.1V 19 5.4V IC3800 1 2.5V 10 2.2V Q101 12.0V 12.0V 11.4V Q212 2.0V 8.0V 2.6V Q833 0.6V 0V 0V
2 11 2 11 20 2 11
4.5V 0V 5.2V 4.6V 4.7V 0V 2.6V Q102 12.0V 0V 12.0V Q213 2.8V 8.0V 3.4V Q835 0V 0.6V 0.1V
3 12 3 12 21 3 12
4.5V 4.6V 4.6V 0V 4.7V 0V 4.4V Q103 12.0V 0V 12.0V Q214 5.1V 0V 5.1V Q836 0V 8.0V 0.6V
4 13 4 13 22 4 13
9.0V 4.6V 4.6V 4.6V 5.3V 0V 0V Q104 5.6V 12.2V 6.2V Q801 0V 0.7V 0V Q851 2.0V 5.1V 2.6V
5 14 5 14 23 5 14
4.5V 4.6V 4.7V 5.5V 4.6V 0V 5.1V Q105 0.7V 4.3V 1.5V Q802 0V 12.0V 0V Q873 0V 0V 0.6V
4.6V
4.6V
4.5V
4.5V
6 15 24 6 15
0.2V 5.4V 9.0V 0V 2.5V Q107 9.5V 12.2V 10.2V Q803 0V 12.0V 0V
7 16
4.6V 4.7V
8 17
4.5V 4.5V
9 18
4.5V 1.9V
7 16
2.2V
2.2V
E C B
E C B
E C B
E C B
E C B
E C B
E C B
E C B
E C B
E C B
E C B
E C B
E C B
E C B
E C B
E C B
E C B
E C B
E C B
E C B
E C B
E C B
E C B
IC202-pin10 <Sandcastle>
1V/div. 20s/div.
DC=0V
DC=0V
DC=0V
DC=0V
DC=0V
DC=0V
DC=0V
DC=0V
0V
3 3
12.2V 0V
IC653 1 4
0V
2 -15.6V 5 0V
2 -14.3V
13.1V
E C B
Q401 0V 32.0V 0.5V Q556 54.7V 13.2V 53.8V Q402-C <H drive>
E C B
E C B
E C B
E C B
E C B
E C B
E C B
E C B
E C B
E C B
E C B
E C B
E C B
E C B
E C B
10V/div.
10s/div.
5V/div.
2ms/div.
2 11 20 2 11
3 12 21 3 12
4 13 22 4 13
5 14
7.0V 0V
6 15
0V
7 16
0V
8 17
4.0V
9 18
0V 6.8V
5 14
4.0V 4.0V
6 15
3.3V 4.1V
7 16
0.4V 9.1V
0V
0V
E C B
E C B
Q2313 E 0V C 6.3V B 0V
DC=0V
DC=0V
DC=0V
DC=0V
DC=0V
DC=0V
IC2311-pin7 <AFC2>
5V/div. 5s/div.
IC2371-pin7 <AFC>
1V/div. 2ms/div.
DC=0V
IC2391-pin7 <Pcct>
2V/div. 10s/div.
DC=0V
DC=0V
2 11 2 2 11 2
3 12 3 3 12 3
4 13 4 4 13 4
5 14 5 5 14 5
6 15 6 6 15 6
7 16 7 7 16 7
0V
0.1V
8 8
5.1V 0V 9 0.1V
0V
2 11 20 29 38 47
3 12 21 30 39 48
4 13 22 31 40
5 14 23 32 41
6 15 24 33 42
7 16 25 34 43
8 17 26 35 44
9 18 27 36 45