Professional Documents
Culture Documents
TW042 Correction UK
TW042 Correction UK
TW042 Correction UK
For this practice use EDT tablets, tractors, dashboard mock up and
training documents.
7. Where can you check the operation of the right pillar keyboard
switches ?
On the switch diagnostic menu in the console
screen.…………………...............…...................……..……………..
9. Select now TECU label code and check/set code AA, how many
choices do you have ?
Only 1 choice: 0 −> with multifunction armrest.…..……..….
12. Run through all the screens available in the diagnostic by functions
menu and mention them:
- General info - Engine speed profile
- Engine configuration - ECU temperature profile
- Engine status - Shutdown log
- SCR process - Software fingerprint log
- Air system - Injector calibration log
- Engine load profile - Digital IO
15. How can you check the operation of the air control system ?
Via the air system screen.…………………………………………
18. Compare the values between the air temperature sensor and the
intake temperature sensor, are the values equal ? Why ?
No the values are different, the air temperature sensor
measures the temperature of fresh air however intake
temperature sensor measures the temperature of mixed air
(fresh air + Exhaust Gas Recirculation). ….……………………
19. What is the status of the different actuators when the tractor is at
idle speed ?
Throttle valve: almost closed (97%), EGR valve: fully closed
(0%), wastegate: fully closed (0%) . …………………………...
22. When you have done the print screen, change the last number of
an injector code or change completely the IQA code. What
happens on the code in the window ?
The code change to AAAAAAA. ………………………………..
23. Change again the code for the injector but with the correct code.
24. Run through all the screens in the Setup and Information Screen
(SIS).
25. Set the SIS screen in basic mode pressing for 5 seconds the OK
and home button, how many screens do you have? Mention them?
3 screens available: Main screen, Instrument panel setting
screen, Error code screen. ……………………………………...
26. Return to the main screen and set the SIS screen in advanced
mode (same procedure), how many screens do you have?
16 screens. ………………………………………………………..
27. With the help of the OIB run through the SIS different menus and
adjust / set some values:
- Adjust the powershuttle sensitivity value to "+3".
- Set the engine memo A to "1500rpm".
- Adjust the speedster value to "+4".
- Set the brightness to "+2".
28. When you are on the main screen what happens if you press the
top or the low arrow of the keypad?
You can select the function displayed on the main screen.
32. With the aid of the OIB, could you describe the functioning of the
comfort lights function?
This function allows the work lights to remain on after the
ignition is switched off. When the function is active, it is
possible to activate the work lights during 15 seconds after
the ignition has been switched OFF. If no action is taken
within 15 seconds, the work lights cannot be activated. The
work lights remain activated for 60 seconds after the control
module switches are pressed. This function allows to activate
only the:
- Hand rails work lights
- Fender work lights
- Front roof work lights
- Rear roof work lights.
33. With the aid of the TSB or the EDT help file, mention what
calibration screens can be selected? What functions are available
in each screen?
- CAL1: high/low speed range , transmission , coupler
function , rear PTO , front PTO .
- CAL2: forward lever , automatic differential & 4 WD
disengagements , clear the calibration values , clear the
stored error codes .
34. How can you adjust the height of the front axle? Pressing the top
or low arrows to increase/decrease the height of the
suspended front axle and then press OK to confirm.
35. What condition you must respect to be able to adjust the height of
the front axle? Ground speed > 5 km/h.
Part 3: Use of the tractor (using OIB, TSB & EDT help file)
37. What is the procedure to set the cab suspension in high position?
Press during 5 second the cab suspension activation switch.
38. What condition must you respect to be able to set the cab in high
position?
Tractor stationary and parklock engaged. …..………………...