Professional Documents
Culture Documents
INDUSTRIAL DUST CATCHER 工业除尘器
INDUSTRIAL DUST CATCHER 工业除尘器
本公司位置
合兴镇
杨 杨
新 锦 张
家
港
公 北 环 路 公 市
果
品
批
路 路 发
市 2
场
0
4
张 杨 公 路
国
北 东 道
二
西 东 市 区 环
路
南
公司地址:张家港市杨锦路合兴工业园区
电 话:0512-58512791
传 真:0512-58512792
邮 编:215626 张家港市洁皇工业吸尘器制造有限公司
ZHANG JIA GANG SHI JIE HUANG industry vacuum manufacturing CO.LTD
O-GX300X6G-L 工业吸尘器
感 谢 您 使 用 洁 皇 工 业 吸 尘 器 电 气 原 理 图
QF
为正确使用,请认真阅读和保管本使用说明书 L1
L2
简 介 L3
SB1
本产品以5.5KW三相异步电动机为动力源,采用电机、风机一
FR 3
体化结构,提高了电机的机械能的利用效率和整机寿命。具有 KM1 KM2 SB2 KM1 KM2
操作简便、耗能省、噪音低、性能稳定、经久耐用、安全可靠、 KM1 KM2
KM1
可连续工作等特点。 KM2
该机广泛适用于各行各业大面积地面、高空墙壁、悬挂设 FR RMR W 6
备、各种机台、设备配套等清洁除尘,适于纤维粉尘、药粉类
33 44
尘埃、颗粒物、金属废屑等类似物体的收集 。 KM2 KM1
PE
型 号 O-GX300X6G-L 序号 代码 名称 型号规格 数量
电 压 三相380V-50Hz 1 M 防爆三相异步电机 380V 5.5KW 1
功 率 5.5KW 2 FR 热继电器 3UA59 40-1K 1
负 压 29000Pa 3 KM1 接触器 3TB42 22-OXQO 1
风 量 370m3/h 4 KM2 接触器 3TB42 22-OXQO 1
吸管内径 Ф60mm 5 SB1 停止按钮 LAY7-11DN 1
电 源 线 10m 2.5mm2×3+1 6 SB2 启动按钮 LAY7-11DN 1
外形尺寸 1100mm×500mm×1100mm 7 RMR 三相相位判断器 1
自 重 160Kg 8 QF 断路器 DZ47-63/3p 20A 1
O-GX300X6G-L 工业吸尘器
结 构 名 称
4 5 6 7 8
注意事项 3 9
10
1.人离开或不工作时必须将电源插头拔下,切除电源。
2
2.不得吸燃着的火种。
3.不得在没有滤尘器、滤尘筒的情况下使用吸尘器,如果让灰 11
尘直接进入风机,将会产生严重问题。
1
4.不得踩踏吸尘软管,以免造成损坏。 12
5.不允许全封闭运转,要确保有足够的空气从软管中吸入风机,
以提高风机的使用寿命。因此,当吸尘器使用一段时间后, 13
滤筒细尘糊筒阻力大时,应打开筒盖用压缩空气对滤筒进行 14
反吹。储尘筒的尘埃过多后要及时清倒,吸头、吸管内的阻
塞物及时清除。 15
6. 吸尘器过载后,吸尘器内的热继电器将会自动断开电路,如 19
果出现这种情况,应拔掉电源插头,找出过载原因,在消除 18 17 16
过载源后按下热继电复位器,使吸尘器恢复正常工作。
1.风机 2.罩壳 3.把手 4.电器控制箱 5.控制按钮
6.电源线 7.出风口 8.筒盖把手 9.筒盖 10.筒盖搭扣
11.滤筒 12.过滤筒体 13.吸口 14.储尘筒搭扣
15.储尘筒 16.筒底脚轮 17.连接板 18.壳体 19.万向轮
清除灰尘
清除灰尘时必须停机进行,将搭扣扳至储尘筒落到地面上, 附备件名称图
双手握住储尘筒拉出。(清倒时应注意不要损坏储尘筒,防止
储尘筒变形。)清倒结束后,按相反步骤将储尘筒安装好。
吸尘硬管 吸尘软管
O-GX300X6G-L 工业吸尘器
使用方法
1.将储尘筒上口对准过滤筒体下口(同心),将过滤筒上的两
边搭扣扣住储尘筒,具体要求过滤筒与储尘筒密封即可。
2.检查筒盖两边搭扣是否扣紧。
直角吸 3.吸口连接软管并用抱箍箍紧,软管另一头装好吸尘硬管和需
用的吸头。
4.检查电源电压是否符合产品铭牌上规定的电压值。
5.使用的三相四线插座是否按规定接地(如下图所示)。
滤 筒 6.接上电源后,控制板上的红色指示灯应发亮。
7.按下启动按钮(Start)吸尘器即开始工作,按下停止按钮
(Stop)吸尘器即停止运转。
直 吸
接地示意图
滤尘袋
地 吸
直角弯头 接 头
本公司位置
合兴镇
杨 杨
INDUSTRIAL DUST CATCHER
新 锦 张
O-GX300-6G
家
港
公 北 环 路 公 市
果
品
批
路 路 发
市 2
场
0
4
张 杨 公 路
国
北 东 道
二
西 东 市 区 环
路
南
Zhang Jia Gang City Industrial Dust Catcher Manufacturing Co. LTD
Thank you for using Jie Huang Industrial Dust Catcher
For correct usage of this product, please read this Instruction Manual.
Introduction
This product uses a 5.5 W three-phase asynchronous motor as power source, with a motor-blower integration structure,
so that greatly improved the motor mechanical energy utilization efficiency as well as the machine life expectancy. It’s easy
to operate, with low energy consumption and noise level, proving to have stable performance, long work life, safe usage and
consistent working abilities.
This machine is widely used in various industries for cleaning dusts on large area ground, upper level walls, suspended
equipments or other machine stations and matching equipments. It’s suitable for collecting things such as fiber dust, powder
dust, granule particles, metal carbonyl debris, etc.
KM2
Power Cable:10m 2.5mm2x3+1
FR RMR W 6
Overall Dimensions:1100mmx500mmx1100mm
33 44
Weight:160kg KM2 KM1
PE
Rigid Tube Flexible Tube Rectangle Suction Head Direct Suction Head
Filter Cylinder Filter Bag Floor Suction Head Elbow Bend Connector
Application Methods
1. Align the upper opening of the storage cylinder with the lower opening of the filter cylinder (concentric), fasten the two
buckle latches on both sides of the filter cylinder with the storage cylinder, making sure the two cylinders are sealed.
2. Check the buckles on both sides of the cylinders are fastened tight.
3. Fix the suction opening to the tube with holt hoop iron, the other end of the tube should be fastened with rigid tube and
the suction head needed.
4. Check the power source voltage is consistent with the rated voltage on the name tag.
5. Check the three-phase four-line socket is grounded accordingly (as the following diagram showed).
6. After the power is on, the red light on the control panel should be lit.
7. Push the Start button on the vacuum for it to start to work, push the Stop button for it to stop.