Download as pdf or txt
Download as pdf or txt
You are on page 1of 3

Test Report No.

7191219811-MEC19/02-ED
dated 23 Mar 2020

Note: This report is issued subject to the Testing and Certification Regulations of the TÜV SÜD Group and the
General Terms and Conditions of Business of TÜV SÜD PSB Pte Ltd. In addition, this report is governed by the
terms set out within this report.

SUBJECT:

Testing of screed

TESTED FOR:

Saint-Gobain (Singapore) Pte Ltd


2 Venture Drive, #09-10
Vision Exchange
Singapore 608526

Attn: Mr Tan Kim Song

SAMPLE DESCRIPTION:

The following item was received on 4 Nov 2019 as shown:

Sample Size Quantity


Screed : ‘E.Mix Easi Screed Eco’ 6 kg 1 bag

The test samples were prepared by TUV SUD PSB Pte Ltd as agreed by the client:
The water/powder ratio was specified by the client as follows:

Test Sample Size Quantity


160 mm x 40 mm x 40 mm prism 6 pcs
‘E.Mix Easi Screed Eco’ with
Ring test specimen:
13.5% water/powder ratio
Ø,outer 126 mm and inner 90 mm x 18 mm thick 3 pcs

TEST METHODS:

Flexural Strength

1. Adopted ASTM C348 : 2018 Standard Test Method For Flexural Strength Of Hydraulic-Cement
Mortars

Test specimen : 160 mm x 40 mm x 40 mm prism


Span length : 100 mm
Crosshead speed : 44.5 N/s
No. of determinations : 3

Laboratory: Phone : +65-6885 1333 Regional Head Office:


TÜV SÜD PSB Pte. Ltd. Fax : +65-6776 8670 TÜV SÜD Asia Pacific Pte. Ltd.
No.1 Science Park Drive E-mail: enquiries@tuv-sud-psb.sg 1 Science Park Drive, #02-01
Singapore 118221 www.tuv-sud-psb.sg Singapore 118221
Co. Reg : 199002667R Page 1 of 3
Test Report No. 7191219811-MEC19/02-ED
dated 23 Mar 2020

Compressive Strength

2. ASTM C349 : 2018 Standard Test Method For Compressive Strength Of Hydraulic
Cement Mortars (Using Portions Of Prisms Broken In Flexure)
Cross-reference : ASTM C109/C109M : 2016a Standard Test Method For Compressive Strength
Of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens)

Test specimen : 160 mm x 40 mm x 40 mm prism


Crosshead speed : 1350 N/s
No. of determinations : 3

Shrinkage Cracking

3. Adopted ASTM C1581/C1581M : 2018a Standard Test Method For Determining Age At Cracking
And Induced Tensile Stress Characteristics Of Mortar And Concrete Under Restrained Shrinkage

Test specimen : Ring


No. of determinations : 3

CONDITIONING:

Unless otherwise specified, all test specimens were conditioned at 23 2 C, 70 15% relative humidity
and tested at 23 2 C, 65 5% relative humidity.

TEST RESULTS:

Test Unit ‘E.Mix Easi Screed Eco’


1. Flexural Strength, average MPa 11.4
2. Compressive Strength, average MPa 34.2
3. Shrinkage Cracking - No cracks

REMARKS:

1. Test age : 28-day cure minimum prior to test as specified by the client.
2. The tests were specified by the client.
The test samples for flexural and compressive strength tests were prepared on 13 Nov 2019
in the presence of Mr Tan Kim Song/Saint-Gobain (Singapore) Pte Ltd.

_____________________ ______________________
Eddie Suwand Fabien Tan
Testing Officer Engineer
Senior Associate Engineer Real Estate & Infrastructure
Mechanical Centre

Page 2 of 3
Test Report No. 7191219811-MEC19/02-ED
dated 23 Mar 2020

Please note that this Report is issued under the following terms :

1. This report applies to the sample of the specific product/equipment given at the time of its testing/calibration. The results are not used to
indicate or imply that they are applicable to other similar items. In addition, such results must not be used to indicate or imply that TÜV SÜD
PSB approves, recommends or endorses the manufacturer, supplier or user of such product/equipment, or that TÜV SÜD PSB in any way
“guarantees” the later performance of the product/equipment. Unless otherwise stated in this report, no tests were conducted to determine
long term effects of using the specific product/equipment.

2. The sample/s mentioned in this report is/are submitted/supplied/manufactured by the Client. TÜV SÜD PSB therefore assumes no
responsibility for the accuracy of information on the brand name, model number, origin of manufacture, consignment or any information
supplied.

3. Nothing in this report shall be interpreted to mean that TÜV SÜD PSB has verified or ascertained any endorsement or marks from any other
testing authority or bodies that may be found on that sample.

4. This report shall not be reproduced wholly or in parts and no reference shall be made by the Client to TÜV SÜD PSB or to the report or results
furnished by TÜV SÜD PSB in any advertisements or sales promotion.

5. Unless otherwise stated, the tests were carried out in TÜV SÜD PSB Pte Ltd, No.1 Science Park Drive Singapore 118221.

July 2011

Page 3 of 3

You might also like