Professional Documents
Culture Documents
Masonry, Stucco & Brick Paint: Floor Coatings
Masonry, Stucco & Brick Paint: Floor Coatings
FILL LEVEL / MAX TINT SURFACE PREPARATION • Apply using a high quality 19-26 mm nap
L3407C White / Tint Base • Allow new stucco and masonry to cure for 30 roller, nylon/polyester brush or airless
3.73 L / 118 mL days before painting. sprayer (.015"-.017" spray tip). Apply a
L3410C Deep Base • Remove all loose, peeling paint. Power wash to second coat, if necessary.
3.43 L / 414 mL remove chalk. Remove dirt, grease and mildew • Maintain a wet edge to avoid lap marks. Do
stains with KILZ Concrete & Masonry Cleaner not re-spread or re-work paint.
SHEEN: < 4 @ 85° & Degreaser.
DRY TIME
COMPOSITION • On galvanized metal, use a diluted solution of 2-3 Hour Dry to Touch: 4 Hour to Recoat.
Vehicle Type: Acrylic KILZ Concrete & Masonry Cleaner & Etcher to Longer dry time required in cooler tempera-
Weight Per 3.79 L (kg): 4.8 (+/-) 0.09 prepare the surface. Rinse thoroughly and tures and higher humidity. After two weeks,
Volume Solids: 31.2% (+/-) 2% allow a minimum of 24 hours to dry. cured paint film may be cleaned with a mild,
Weight Solids: 44.4% (+/-) 2% • Cracks and gaps wider than 1.5 mm should be non-abrasive liquid detergent.
Viscosity: 95-105 KU routed open, dusted and patched with a quality
patching compound. Use an acrylic caulk
VOC (COV): <50 g/L around windows, doors and trim. Scuff sand
The addition of colourants may add VOCs. glossy surfaces.
FLASHPOINT: N/A • If chalk remains on the surface, prime with a
KILZ Premium Primer. Prime all patched areas
COVERAGE* as well as adjacent wood and metal surfaces. If
23 - 37 m2 (250 - 400 sq. ft.) per 3.79 L, previously sealed or coated, check
depending on the surface texture, porosity and manufacturer's specifications before painting.
application method. Does not include the loss
of material from spraying. APPLICATION
• Do not dilute. Intermix all cans of same
RECOMMENDED FILM THICKNESS product to ensure colour uniformity. Stir paint
At 23 m2 (250 sq. ft.) per 3.79 L: before and occasionally during application.
• Wet: 6.4 mils; Dry: 2.0 mils • For best results, apply when air and surface
At 37 m2 (400 sq. ft.) per 3.79 L: temperatures are between 10-32˚ C. Do not
• Wet: 4.0 mils; Dry: 1.3 mils use if rain or heavy dew is expected within 24
hours.
FLOOR COATINGS
MASONRY, STUCCO
& BRICK PAINT
GENERAL INFORMATION
Keep From Freezing / Read All Directions Before Opening Container
WARNING! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. Contact the National Lead Information Hotline at 1-800-
424-LEAD or log on to www.epa.gov/lead.
WARNING! Sanding or scraping pressure treated lumber may be hazardous; wear appropriate protection.
MAY IRRITATE EYES AND SKIN. Avoid contact with eyes, skin and clothing. Do not breathe fumes. Keep out of reach of children. Wear
eye protection and protective clothing. Use only with adequate ventilation.
FIRST AID
• Contains ETHYLENE GLYCOL. If swallowed, call a Poison Control Centre or doctor immediately. Do not induce vomiting.
• If in eyes, rinse with water for 20 minutes.
• If on skin, rinse well with water.
• If inhaled, move person to fresh air.
CAUTION
KEEP OUT OF REACH OF CHILDREN
DO NOT TAKE INTERNALLY