Professional Documents
Culture Documents
05 Suspension (Ok)
05 Suspension (Ok)
05 Suspension (Ok)
06
MODEL 374375, 930, 932, 933, 934, 940, 942, 943, 944, 950, 952, 953, 954, 958
with 2 driven, steel-sprung rear axles
1 Bolt
2 Bolt
3 Bracket
4 Spacer sleeve
5 Spring U-bolt
6 Spring seat
7 Rear spring
8 Rubber bushing
9 Nut
10 Nut
11 Rubber bushing
W32.20-0014-06
Modification notes
7.6.05 Spring U-bolt nut, rear spring to rear spring seat *BA32.20-N-1003-03C
Remove/install
1 Secure vehicle against rolling
2 Jack up vehicle and support vehicle frame The vehicle must be unloaded.
3 Remove rear wheels Only on side from which spring is to be AR40.10-W-1100A
removed.
4 Lift both rear axles until spring (7) is relieved Use a jack or inspection pit lift.
of load
5 Prop rear axles
6 Remove spring U-bolt (5) and spring seat (6) Installation: Use new nuts (10).
*BA32.20-N-1003-03C
*000589696300
7 Remove nuts (9) from rubber mounts (8, 11) Installation: Use new nuts (9).
*BA32.20-N-1002-03C
8 Remove bolts (1, 2) together with bracket (3)
and spacer sleeves (4)
9 Remove rear spring (7) Installation: Lightly grease mounting hole *BR00.45-Z-1020-06A
for center bolt with leaf spring grease.
10 Install in the reverse order
BA32.20-N-1003-03C Spring U-bolt nut, rear spring to rear Nm 900 900 900
spring seat
000 589 69 63 00
Ratio wrench
Repair materials
Number Designation Order number
BR00.45-Z-1020-06A Leaf-spring grease (refer to Specifications for Operating Fluids, Sheet no. -
268)
1 Shock absorber
2 Self-locking nut
3 Screw
4 Front spring
5 Nut
6 Spring U-bolt
7 Spring seat
8 Spring support
9 Screw
10 Self-locking nut
11 Stabilizer
12 Bearing cap
13 Screw
14 Screw
15 Washer
16 Plastic bearing
17 Link rod
18 Screw
19 Washer
20 Screw
21 Nut
W32.20-0001-06
Modification notes
6.3.09 Value modified: Bolt, front spring to spring bracket front Model 930, 932, 934 with front axle 730 *BA32.20-N-1002-01B
and rear Model 374.5, 950, 952, 954 with front axle
730
Remove/install
1 Secure vehicle against rolling
2 Remove air filter housing Only when removing the right front
spring.
3 Jack up vehicle and support vehicle frame
4 Lift front axle sufficiently to take load from Use a jack or inspection pit lift.
front spring
5 Detach shock absorber (1) from front axle *BA32.25-N-1001-01B
*BA32.25-N-1002-01B
6 Detach connecting rod (17) from anti-roll bar
7 Detach bearing cap (12) from spring pad (8)
8 Remove spring U-bolt (6) and spring seat (7) Installation: Replace self-locking nuts
(10).
*BA32.20-N-1001-01B
9 Unscrew nuts (5, 21) on front and rear *BA32.20-N-1002-01B
spring brackets and drive out bolts (3, 20)
using a suitable drift
10 Lower front axle and remove front spring (4) Installation: Grease mounting bore for *BR00.45-Z-1020-06A
and spring pad (8) from axle the center bolt in the spring washer (8)
lightly. When lifting the front axle, ensure that
the center bolt engages in the mounting
bore.
11 Check front spring bushes for wear and AR32.20-W-0210A
replace if necessary
12 Install in the reverse order
BA32.20-N-1001-01B Nut to spring shackle of front axle M20 1.5 Nm 500 500 500
M22 1.5 Nm - - -
Repair materials
Number Designation Order number
BR00.45-Z-1020-06A Leaf-spring grease (refer to Specifications for Operating Fluids, Sheet no. -
268)
W31.30-1006-01
Removing
1 Remove rear spring bracket (1) With HuckSpin connection:
Frame
M12 1.5 Nm 95 95 95
Stage 2 ° 90 90 90
Stage 2 ° 90 90 90
Stage 2 ° 90 90 90
Frame
M12 1.5 Nm 95 95 95
© Daimler AG, 7/2/13, G/03/13, ar32.20-w-0002a, Remove/install rear spring bracket for front spring Page 1 of 2
MODEL 374, 375, 930, 932, 933, 934, 940, 942, 943, 944, 950, 952, 953, 954, 957, 958, 970, 972, 974, 975, 976
M14 1.5 Stage 1 Nm 150 150 150
Stage 2 ° 90 90 90
Stage 2 ° 90 90 90
Stage 2 ° 90 90 90
© Daimler AG, 7/2/13, G/03/13, ar32.20-w-0002a, Remove/install rear spring bracket for front spring Page 2 of 2
MODEL 374, 375, 930, 932, 933, 934, 940, 942, 943, 944, 950, 952, 953, 954, 957, 958, 970, 972, 974, 975, 976
AR32.20-W-0003B Remove/install front spring bracket for rear spring 2.3.10
MODEL 374, 375, 930, 932, 933, 934, 940, 942, 943, 944, 950, 952, 953, 954, 957, 958, 970, 972, 974, 975, 976
1 Spring bracket
2 Washer plate
3 Bolt or HuckSpin connection
4 Nut or HuckSpin connection
W31.30-1014-01
Removing
1 Remove spring bracket (1) and spacers (2) With HuckSpin connection:
Frame
M12 1.5 Nm 95 95 95
Stage 2 ° 90 90 90
Stage 2 ° 90 90 90
Stage 2 ° 90 90 90
Frame
© Daimler AG, 7/2/13, G/03/13, ar32.20-w-0003b, Remove/install front spring bracket for rear spring Page 1 of 2
MODEL 374, 375, 930, 932, 933, 934, 940, 942, 943, 944, 950, 952, 953, 954, 957, 958, 970, 972, 974, 975, 976
BA31.30-N-1002-01A Bolt, frame sections to frame M10 1.5 Nm - - -
M12 1.5 Nm 95 95 95
Stage 2 ° 90 90 90
Stage 2 ° 90 90 90
Stage 2 ° 90 90 90
© Daimler AG, 7/2/13, G/03/13, ar32.20-w-0003b, Remove/install front spring bracket for rear spring Page 2 of 2
MODEL 374, 375, 930, 932, 933, 934, 940, 942, 943, 944, 950, 952, 953, 954, 957, 958, 970, 972, 974, 975, 976
AR32.20-W-0001A Remove/install center spring bracket for front spring 2.3.10
MODEL 374, 375, 930, 932, 933, 934, 940, 942, 943, 944, 950, 952, 953, 954, 957, 958, 970, 972, 974, 975, 976
W31.30-1005-01
Removing
1 Remove center spring bracket (1) With HuckSpin connection:
Frame
M12 1.5 Nm 95 95 95
Stage 2 ° 90 90 90
Stage 2 ° 90 90 90
Stage 2 ° 90 90 90
Frame
M12 1.5 Nm 95 95
© Daimler AG, 7/2/13, G/03/13, ar32.20-w-0001a, Remove/install center spring bracket for front spring Page 1 of 2
MODEL 374, 375, 930, 932, 933, 934, 940, 942, 943, 944, 950, 952, 953, 954, 957, 958, 970, 972, 974, 975, 976
Stage 2 ° 90 90
Stage 2 ° 90 90
Stage 2 ° 90 90
© Daimler AG, 7/2/13, G/03/13, ar32.20-w-0001a, Remove/install center spring bracket for front spring Page 2 of 2
MODEL 374, 375, 930, 932, 933, 934, 940, 942, 943, 944, 950, 952, 953, 954, 957, 958, 970, 972, 974, 975, 976
AR32.20-W-0240A Remove/install rubber mount of rear axle spring 23.11.10
MODEL 374, 375, 930, 932, 933, 934, 940, 942, 943, 944, 950, 952, 953, 954, 958
with 2 driven, steel-sprung rear axles
1 Screw
2 Screw
3 Bracket
4 Distance sleeve
5 Rear spring
6 Nut
7 Mounting plate
8 Rubber bushing
9 Rear axle
10 Spherical washer
11 Rod mount
12 Nut
13 Trailing arm
14 Screw
15 Screw
16 Nut
17 Washer
18 Screw
19 Shock absorber
W32.20-0015-06
Remove/install
1 Secure vehicle against rolling
2 Jack up vehicle and support vehicle frame Vehicle unloaded.
3 Remove rear wheels Only on side at which rubber mount is to AR40.10-W-1100A
be removed.
4 Lift rear axle (9) until rear spring is relieved Use a jack or inspection pit lift.
of load
5 Remove shock absorber (19) from link *BA32.25-N-1005-03D
bracket (11)
6 Remove trailing arm (13) from rod mount (11) *BA35.15-N-1006-03A
7 Remove rod mount (11) together with Installation: Use new bolts (14). Install
spherical washers (10) from axle housing the longer bolts at the shock absorber end.
and then remove mounting plates (7) Make sure that correct number of spherical
washers (10) is fitted and that they are
seated correctly.
*BA35.10-N-1001-03E
*BA35.10-N-1003-03B
8 Unscrew nuts (6) *BA32.20-N-1002-03C
9 Remove bolts (1, 2) together with bracket (3)
and spacer sleeves (4)
10 Lower rear axle and remove rubber mount
(8) from axle carrier
11 Install in the reverse order
© Daimler AG, 7/2/13, G/03/13, ar32.20-w-0240a, Remove/install rubber mount of rear axle spring Page 1 of 3
MODEL 374, 375, 930, 932, 933, 934, 940, 942, 943, 944, 950, 952, 953, 954, 958 with 2 driven, steel-sprung rear axles
BA32.25-N-1005-03D Nut of shock absorber to steel suspension Nm 250
link bracket
Control arm
Rear axle
Rear axle
Rear axle
© Daimler AG, 7/2/13, G/03/13, ar32.20-w-0240a, Remove/install rubber mount of rear axle spring Page 2 of 3
MODEL 374, 375, 930, 932, 933, 934, 940, 942, 943, 944, 950, 952, 953, 954, 958 with 2 driven, steel-sprung rear axles
Number Designation Models 930, 932, Model Model
933, 934 958.4 with 958.2 with
with rear axle rear axle 740.8 rear axle 741.9
748.2
© Daimler AG, 7/2/13, G/03/13, ar32.20-w-0240a, Remove/install rubber mount of rear axle spring Page 3 of 3
MODEL 374, 375, 930, 932, 933, 934, 940, 942, 943, 944, 950, 952, 953, 954, 958 with 2 driven, steel-sprung rear axles
AR32.20-W-0250A Remove/install rear spring seat bearing 17.2.06
MODEL 374, 375, 930, 932, 933, 934, 940, 942, 943, 944, 950, 952, 953, 954, 958
with 2 driven, steel-sprung rear axles
1 Plastic ring
2 Rubber bushing
3 Upper bearing shell
4 Bolt
5 Cover
6 Nut
7 Lower bearing shell
W32.20-1003-06
Remove/install
1 Remove rear spring AR32.20-W-0230B
2 Remove cover (5) *BA32.20-N-1005-03C
3 Remove upper and lower bearing shell (3 Installation: Use new bolts (4) and nuts
and 7) (6).
*BA32.20-N-1004-03C
4 Remove rubber mount (2)
5 Remove plastic ring (1)
6 Install in the reverse order
7 Retighten nuts (6) at bearing shells once *BA32.20-N-1004-03C
again
BA32.20-N-1004-03C Nut, lower bearing shell to upper M20 1.5 Nm 460 460 460
bearing shell of center bearing
© Daimler AG, 7/2/13, G/03/13, ar32.20-w-0250a, Remove/install rear spring seat bearing Page 1 of 2
MODEL 374, 375, 930, 932, 933, 934, 940, 942, 943, 944, 950, 952, 953, 954, 958 with 2 driven, steel-sprung rear axles
BA32.20-N-1004-03C Nut, lower bearing shell to upper M20 1.5 Nm 460 460 460
bearing shell of center bearing
© Daimler AG, 7/2/13, G/03/13, ar32.20-w-0250a, Remove/install rear spring seat bearing Page 2 of 2
MODEL 374, 375, 930, 932, 933, 934, 940, 942, 943, 944, 950, 952, 953, 954, 958 with 2 driven, steel-sprung rear axles
AR32.20-W-0210A Remove/install front spring bush 17.2.06
MODEL 374.5 /6, 375.3 /4, 930, 932, 933, 934, 940, 942, 943, 944, 950, 952, 953, 954, 957, 958.2 /4 with CODE (ID1) Leaf
suspension
Removing
1 Remove front springs AR32.20-W-0200A
2 Connect hydraulic hose to the hand pump Hydraulic hose *652589003323
and the hollow cylinder (22)
Hand pump *652589003321
Hollow cylinder *652589003322
3 Attach hollow cylinder (22) and Threaded spindle *652589003311
corresponding threaded sleeve (1) with the
threaded spindle (11) to the bearing bush (3)
and screw on tightly with the associated
thrust piece for pressing out (2)
Insertion and extraction tool for bearing *652589003301
bush dia. 58 mm.
Insertion and extraction tool for bearing *950589023300
bush dia. 60 mm.
Insertion and extraction tool for bearing *652589003302
bush dia. 65 mm.
Insertion and extraction tool for bearing *950589013300
bush dia. 75 mm.
4 Press out bearing bushing
Install
5 Insert new bearing bushing (3) in the The chamfered side of the bearing bush
corresponding conical sleeve (4) and slide must face towards the spring eye.
forwards using the suitable thrust piece for
pressing in (5)
Insertion and extraction tool for bearing *652589003301
bushes dia. 58 mm.
Insertion and extraction tool for bearing *950589023300
bushes dia. 60 mm.
Insertion and extraction tool for bearing *652589003302
bushes dia. 65 mm.
Insertion and extraction tool for bearing *950589013300
bushes dia. 75 mm.
6 Attach hollow cylinder (22) to the front Hollow cylinder *652589003322
spring and screw the conical sleeve (4)
tightly onto the threaded spindle (11)using
the suitable thrust piece for pressing in (5)
Threaded spindle *652589003311
7 Draw in bearing bushing (3) Through the cutout (arrow) in the conical
sleeve (4) check whether the bearing
bushing is pressed in fully.
8 Install front spring AR32.20-W-0200A
© Daimler AG, 7/2/13, G/03/13, ar32.20-w-0210a, Remove/install front spring bush Page 1 of 2
MODEL 374.5 /6, 375.3 /4, 930, 932, 933, 934, 940, 942, 943, 944, 950, 952, 953, 954, 957, 958.2 /4 with CODE (ID1) Leaf suspension
652 589 00 33 01 652 589 00 33 02 652 589 00 33 11 652 589 00 33 21
Removal and installation tool Removal and installation tool Threaded spindle Hand pump
© Daimler AG, 7/2/13, G/03/13, ar32.20-w-0210a, Remove/install front spring bush Page 2 of 2
MODEL 374.5 /6, 375.3 /4, 930, 932, 933, 934, 940, 942, 943, 944, 950, 952, 953, 954, 957, 958.2 /4 with CODE (ID1) Leaf suspension
AR32.25-W-0110A Remove/install rear shock absorber 17.10.12
MODEL 374, 375, 930, 932, 933, 934, 940, 942, 943, 944, 949, 950, 952, 953, 954, 957, 958
Upper attachment point on frame, shown Lower attachment point on link bracket, Lower attachment point on air bellows
on model 944 with steel suspension support, with air suspension
Remove/install
© Daimler AG, 7/2/13, G/03/13, ar32.25-w-0110a, Remove/install rear shock absorber Page 2 of 2
MODEL 374, 375, 930, 932, 933, 934, 940, 942, 943, 944, 949, 950, 952, 953, 954, 957, 958
AR32.25-W-0105A Remove/install front shock absorber 8.4.09
MODEL 374, 375, 930, 932, 933, 934, 940, 942, 943, 944, 950, 952, 953, 954, 957, 958, 970, 972, 974, 975, 976
1 Top bolt
2 Self-locking nut (top)
3 Shock absorber
4 Bottom bolt
5 Self-locking nut (bottom)
W32.25-0001-06
Remove/install
Notes on self-locking nuts and bolts AH00.00-N-0001-01A
1 Detach shock absorber (3) at bottom *BA32.25-N-1001-01B
2 Detach shock absorber (3) at top *BA32.25-N-1002-01B
3 Install in the reverse order
© Daimler AG, 7/2/13, G/03/13, ar32.25-w-0105a, Remove/install front shock absorber Page 1 of 1
MODEL 374, 375, 930, 932, 933, 934, 940, 942, 943, 944, 950, 952, 953, 954, 957, 958, 970, 972, 974, 975, 976
AR32.35-W-2050A Remove/install front stabilizer bar 5.10.11
MODEL 374, 375, 930, 932, 933, 934, 940, 942, 943, 944, 950, 952, 953, 954, 958
steel-sprung front axle
1 Hexagon bolt
2 Washer
3 Plastic bearing
4 Link rod
5 Hexagon bolt
6 Washer
7 Hexagon bolt
8 Bearing cap
9 Stabilizer
W32.35-0001-06
Modification notes
25.2.05 Bolt of bearing cap to spring pad Model 375.3/4, 930, 932, 933, 934, 944, 950, *BA32.35-N-1001-02A
952, 953, 954
18.5.05 Bolt of bearing cap to spring pad Model 375.3/4, 930, 932, 933, 934, 940, 942, *BA32.35-N-1001-02A
943, 944, 950, 952, 953, 954
Bolt of stabilizer to link rod Model 375.3/4, 930, 932, 933, 934, 940, 942, *BA32.35-N-1002-02A
943, 944, 950, 952, 953, 954
Bolt of connecting rod to bearing bracket Model 375.3/4, 930, 932, 933, 934, 940, 942, *BA32.35-N-1003-02A
943, 944, 950, 952, 953, 954
Remove/install
1 Remove connecting rods (4) *BA32.35-N-1003-02A
*BA32.35-N-1002-02A
2 Detach bearing cap (8) from spring pad and *BA32.35-N-1001-02A
remove anti-roll bar (9)
3 Install in the reverse order
© Daimler AG, 7/2/13, G/03/13, ar32.35-w-2050a, Remove/install front stabilizer bar Page 1 of 1
MODEL 374, 375, 930, 932, 933, 934, 940, 942, 943, 944, 950, 952, 953, 954, 958 steel-sprung front axle
AR32.35-W-2210E Remove/install anti-roll bar on rear axle 15.1.10
MODEL 374, 375, 655, 656, 657, 658, 659, 930, 932, 933, 934, 940, 942, 943, 944, 950, 952, 953, 954, 958
bei stahlgefederter Hinterachse
1 Link rod
2 Washer
3 Screw
4 Stabilizer
5 Bearing bushing
6 Bearing cap
7 Screw
W32.35-1033-06
Modification notes
Remove/install
1 Secure stabilizer to prevent it from falling
2 Detach bearing covers (6) from link brackets *BA32.35-N-1001-03D
and press anti-roll bar (4) out of bearing
3 Unscrew bolts (3) with washers (2) on *BA32.35-N-1007-03D
connecting rods (1)
4 Remove anti-roll bar (4) with connecting rods
(1)
5 Check bearing bushings (5) of stabilizer bar If worn:
for wear
Replace bearing bushings. AR32.35-W-2210-04A
Hand pump *652589003321
Hydraulic cylinder *652589003322
Hydraulic hose *652589003323
Threaded spindle *652589003311
Insertion and extraction tool for bearing *652589003301
bushing dia. 58 mm.
Insertion and extraction tool for bearing *950589023300
bushing dia. 58 mm.
Insertion and extraction tool for bearing *652589003302
bushing dia. 65 mm.
Insertion and extraction tool for bearing *950589013300
bushing dia. 75 mm.
6 Check connecting rod bearing bushings (1) If worn:
for wear
Replace bearing bushings. AR32.35-W-2210-02A
Hand pump *652589003321
Hydraulic cylinder *652589003322
Hydraulic hose *652589003323
Threaded spindle *652589003311
Insertion and extraction tool for bearing *652589003301
bushing dia. 58 mm.
Insertion and extraction tool for bearing *950589023300
bushing dia. 58 mm.
© Daimler AG, 7/2/13, G/03/13, ar32.35-w-2210e, Remove/install anti-roll bar on rear axle Page 1 of 3
MODEL 374, 375, 655, 656, 657, 658, 659, 930, 932, 933, 934, 940, 942, 943, 944, 950, 952, 953, 954, 958 bei stahlgefederter Hinterachse
Insertion and extraction tool for bearing *652589003302
bushing dia. 65 mm.
Insertion and extraction tool for bearing *950589013300
bushing dia. 75 mm.
7 Install in the reverse order
BA32.35-N-1001-03D Bolt of stabilizer bearing bracketing M12 1.5 Nm 100 100 100 100
to link bracket
M20 1.5 Nm - - - -
BA32.35-N-1007-03D Bolt, connecting rod (pull rod) to anti- M16 1.5 Nm 270 270 270 270
roll bar and bearing bracket
M20 1.5 Nm - -
BA32.35-N-1007-03D Bolt, connecting rod (pull rod) to anti- M16 1.5 Nm 270 270
roll bar and bearing bracket
© Daimler AG, 7/2/13, G/03/13, ar32.35-w-2210e, Remove/install anti-roll bar on rear axle Page 2 of 3
MODEL 374, 375, 655, 656, 657, 658, 659, 930, 932, 933, 934, 940, 942, 943, 944, 950, 952, 953, 954, 958 bei stahlgefederter Hinterachse
652 589 00 33 22 652 589 00 33 23 950 589 01 33 00 950 589 02 33 00
Hollow cylinder Hydraulic hose (complete) Press-in/out tool Removal and installation tool
© Daimler AG, 7/2/13, G/03/13, ar32.35-w-2210e, Remove/install anti-roll bar on rear axle Page 3 of 3
MODEL 374, 375, 655, 656, 657, 658, 659, 930, 932, 933, 934, 940, 942, 943, 944, 950, 952, 953, 954, 958 bei stahlgefederter Hinterachse