Professional Documents
Culture Documents
The Installation Is Essentially Divided Into 4 Parts
The Installation Is Essentially Divided Into 4 Parts
1. Speedometer
& Accelerator Pedal
Removal
2. Connection and
installation of
the control electronics
3. Installation
of the control unit
4. Assembly/installation
of all components in the
vehicle
To the To the
A speed signal is cruise control lever speedometer
made available
at this connection.
Eg for connection to a
navigation device.
cruise control lever
The cruise
control can be switched
off completely here,
for example if the
cruise control is
defective.
After connecting the gas pedal plug, the LED, the cruise control/wiper lever and the
speedometer connection cable are connected.
Attention :
The cruise control is NOT an autopilot.
The cruise control only regulates the speed.
The cruise control does NOT have a braking function.
The driver must continue to pay attention to the traffic and, if
necessary, switch off the cruise control!
The cruise control regulates the stored speed of the smart and thus increases driving
comfort considerably.
In addition, it has a TempoMax function that prevents the stored speed from being
exceeded.
In addition, the stored speed can be changed or called up again.
lower area.
Service:
Operation is extremely simple. Pressing the cruise control button (cancel/mode) accepts and
maintains the current speed.
The stored speed of the cruise control can be changed later with the +CONT or -SET button.
Resolution 1kmh By pressing the +CONT button (continue) when the cruise control is switched
off, the last saved value is called up again.
Configuration:
For individual configuration, the cruise control can be adapted to the needs of the user.
operating unit
cruise control
On off
TempoMax
the end
cruise control:
Switch on: press the button at the end of the lever Switch
off: press the button at the end of the lever again or brake Change speed: turn the
rotating ring to plus or minus. (1mkh per switching pulse)
The cruise control function is switched off automatically when the brake is applied.
In addition, the behavior when accelerating during the cruise control function can be specified once during
commissioning. This determines whether the cruise control:
If the switch-off function is selected, the accelerator pedal must be released within the
takeover time of 2.5s. This takeover time is indicated by the red LED and green LED
displayed.
The cruise control works in the range from 25 km/h to 160 km/h.
TempoMax ( -Set ):
Switching on: With the cruise control switched off, turn the rotary ring down (- set) once.
Switching off: Press the button at the end of the lever.
Change speed: turn the rotary ring to plus or minus. (approx. 1kmh per switching pulse)
This function reliably prevents the stored speed from being exceeded, eg driving on a construction site
at 80 km/h on a motorway.
Commissioning/programming:
Display via the built-in 3-color LED or via the optionally available, external light-emitting diode
cable, as well as with the MDC on-board computer in plain text!
Here, the control electronics makes a correction for better accelerator pedal response in the lower area.
The correction can either be switched off completely (delivery status) or selected accordingly in four
further stages.
ATTENTION the 1st menu is activated first. Hold the button longer until the yellow LED flashes!!!
5. Menu button -set (immobilizer) The immobilizer is only available as a special order!
If all inputs are correct, the input menu is closed automatically, otherwise the inputs must be repeated.
The code consists of any order of the three keys and always consists of four entries.
Individual keys can also be assigned multiple times.
Eg button plus - button plus - button minus - button cruise control
To switch the immobilizer on or off, simply enter the defined order of the keys.
When the immobilizer is active, you cannot accelerate. The LED lights up red.
Note: In the case of incorrect entries, the code can be repeated after 5s.
• On ÿ
Blinks normally
ÿÿ Blinks quickly
From software version 2.1, our on-board computer can also be used instead of the
optional control LED.
The operating states of the cruise control are shown on the BC's display
!! Attention !!
After each engine start, the control diode flashes until the brake is actuated for the first time.
The function of the brake switch is checked.
If the brake switch is defective, the diode continues to flash and the cruise control cannot be
switched on!
If the control diode flashes green > red > yellow continuously, either a door/tailgate is not properly closed or
the handbrake is still on.
Attention
Only when using our on-board computer at the same time
CAN message 707 Activation for displaying the cruise control functions in the on-board computer:
Simultaneously :
Standstill > no handbrake > right door closed > press and hold the
foot brake > hold the minus button for 40 seconds >
Confirmation by rapid flashing of the LED green=active or red=not active > release the
minus button > ignition off > ignition on.
All operating states of the cruise control are now displayed in the on-board computer.