Professional Documents
Culture Documents
13.7.5 DSC Bus Check: 13.8 Memory/Storage Status
13.7.5 DSC Bus Check: 13.8 Memory/Storage Status
State Confirmation
<Procedure>
1. Press [Memory Bus Check].
2. Select either [Scanner -> Memory], [Memory -> PRT], or both.
3. Press the Start key to start the check procedure.
4. The check result will be displayed.
13.7.7 Format
• Clear the data from the MFP storage.
NOTE
▪ Data stored in the firmware space and backup space are not cleared.
▪ The movie data needs to be reinstalled as necessary since this data will be deleted by format.
Physical format
1. Touch [Format] -> [Physical Format].
2. Press the Start key to start the formatting sequence.
3. The sequence will be automatically terminated as it is completed.
4. Turn off the main power switch and turn it on again more than 10 seconds after.
NOTE
▪ After termination of physical formatting, start the sequence of logical formatting.
Logical format
1. Touch [Format] -> [Logical Format].
2. Press the Start key to start the formatting sequence.
3. The sequence will be automatically terminated as it is completed.
4. Turn off the main power switch and turn it on again more than 10 seconds after.
13.8 Memory/Storage Status
• To display the condition and amount of the memory and MFP storage.
13.9 Load Check
• To check each device (electric component) for proper condition by individually activating the load associated with the device.
• To identify faults at the time of troubleshooting.
NOTE
Take note of the following during the load check mode.
• No malfunction is detected and no count is taken of consumables life and related items.
• Two or more devices (motors, clutches, solenoids, and fans) cannot be checked simultaneously.
• Detection of proper installation of various types of units and waste toner box does not function. During the check procedure,
therefore, make sure that the unit in question is installed correctly or yet to be installed.
<Procedure>
1. Open the front door, lower front door or the right door.
2. Touch [Start Load Check].
3. Close the door opened on step 1.
4. Referring to the load check list, enter a check code.
5. Referring to the load check list, enter a multi code.
6. Press the Start key.
• When pressing the Start key, the specified load is activated. The Start key blinks in orange.
7. Check the load operation and output of signals.
8. Press the Stop key to stop the check operation and check the result.
NOTE
▪ Depending on the type of load being activated, after the lapse of the specified time or after the transition to the specified
state, the corresponding device automatically stops working.
▪ When ‘NG’ is displayed, check the wiring and connectors.
9. To check another load or signal output, repeat steps 4 to 8.
10. Turn OFF the main power switch and turn it ON again more than 10 seconds after.
NOTE
▪ To exit from the load check mode, be sure to turn off and on the main power switch.
At the point when you display [Service Mode] -> [State Confirmation] -> [Load Check], the machine enters into load check mode.
Regardless of whether load check is actually performed or not, the main power switch must be turned off and on to exit from load
check mode.
I-62
bizhub 306i/266i/246i/226i I SERVICE MODE > 13. State Confirmation
26 1 - Registration roller high speed Drives the registration clutch during rotating -
the main motor stably.
28 1 - Manual bypass paper feed roller Drives the bypass paper feed clutch during -
high speed rotating the main motor stably.
101 - Tray 1 paper feed roller high Drives the tray 1 paper feed clutch during -
speed rotating the main motor stably.
105 - Tray 2 paper feed roller high Drives the tray 2 paper feed clutch during -
speed rotating the main motor stably.
109 - Tray 3 paper feed roller high Drives the tray 3 paper feed clutch during -
speed rotating the main motor stably.
121 - Tray 4 paper feed roller high Drives the tray 4 paper feed clutch during -
speed rotating the main motor stably.
125 - Tray 5 paper feed roller high Drives the tray 5 paper feed clutch during -
speed rotating the main motor stably.
32 1 M4 Polygon motor high speed Drives the motor at the specified speed. -
40 1 M2 Main motor high speed Drives the motor at the specified speed. -
42 1 FM3 Toner suction fan Drives the specified fan. -
2 FM1 Suction fan
3 FM2 Cooling fan
43 2 M5 Toner supply motor Drives the toner supply motor. -
60 33 M1 Document feed motor speed1/ • Drives the motor at the specified speed. Only when DF-633 is
normal rotation (300dpi • Stop rotating when pressing the Stop key. mounted.
Monochrome)
34 Document feed motor speed2/
normal rotation (600dpi
Monochrome)
35 Document feed motor speed3/
normal rotation (300dpi Color)
36 Document feed motor speed4/
normal rotation (600dpi Color)
38 Document feed motor speed1/
reverse rotation (300dpi
Monochrome)
39 Document feed motor speed2/
reverse rotation (600dpi
Monochrome)
40 Document feed motor speed3/
reverse rotation (300dpi Color)
41 Document feed motor speed4/
reverse rotation (600dpi Color)
145 CL1 Paper feed clutch • Drives the specified clutch.
146 CL2 Registration clutch • Stop rotating when pressing the Stop key.
84 1 M3 Switchback motor high speed Drives the motor at the specified speed and -
(paper exit) direction.
4 Switchback motor high speed
(paper reverse)
85 1 M6 AD motor high speed Drives the motor at the specified speed. -
I-63