Professional Documents
Culture Documents
Link-Tkif Technische Daten 2020 Hb50 6p Online
Link-Tkif Technische Daten 2020 Hb50 6p Online
Infrastructure
Drifter
HB50
Drifter HB50
Drifter HB50
HB50 is a Drifter (top-hammer) especially developed for:
• Micropile drilling up to a casing diameter of 7 inches (ø178 mm)
• Overburden drilling up to an outside casing diameter of 6 inches (ø152,4 mm)
• Threaded hollow bar drilling (self-drilling anchors) up to a bar diameter of 4 inches (ø103 mm)
• Auger drilling (CFA) up to an auger diameter of 24 inches (ø600 mm)
HB50 has a standard built-in hydraulic damping mechanism to avoid blank impacts and to allow
percussion during retraction of casings and augers.
HB50 achieves optimum drilling performance in different types of soil by adjusting the impact
frequency and the impact energy; three different impact frequencies and impact energies
are available.
HB50 offers three different ways to switch between the percussion mechanism and the speed
of the rotary drive, either electrically or hydraulically or manually (by hand).
HB50 offers two different high-speed and high-pressure motors (677 ccm, 940 ccm) and two
single-speed motors (670 ccm, 677 ccm).
Rotary Drives
Motor-Version 670 ccm (single-speed)
Torque (Nm) 4,200 8,500 5,300 10,700 12,800
120
Speed (rpm) 61 29 59 29 27
(lpm)
Pressure at rotary drive 170 bar 200 bar 240 bar 280 bar
Gear 2 nd
1 st
2 nd
1 st
2 nd
1 st
2nd 1st
Torque (Nm) 5,100 10,900 6,200 13,200 7,400 15,600 8,800 18,300
090 Speed (rpm) 43 21 43 21 43 21 43 21
Oil flow rate
Torque (Nm) 4,800 10,600 5,900 12,900 7,100 15,300 8,500 18,000
120
Speed (rpm) 57 28 57 28 57 28 57 28
(lpm)
Torque (Nm) 4,100 10,100 5,300 12,500 6,400 14,800 7,800 17,500
170
Speed (rpm) 80 40 80 40 80 40 80 40
1st gear (parallel mode), 2nd gear (serial mode)
Pressure at rotary drive 170 bar 200 bar 240 bar 280 bar
Gear 4th 3rd 2nd 1st 4th 3rd 2nd 1st 4th 3rd 2nd 1st 4th 3rd 2nd 1st
Torque (Nm) 3,200 5,100 7,100 10,900 3,900 6,200 8,700 13,200 4,700 7,400 10,300 15,600 5,600 8,800 12,100 18,300
090 Speed (rpm) 64 43 32 21 64 43 32 21 64 43 32 21 64 43 32 21
Oil flow rate
Torque (Nm) 2,400 4,800 6,900 10,600 3,200 5,900 8,500 12,900 4,000 7,100 10,100 15,300 4,900 8,500 11,900 18,000
120
Speed (rpm) 85 57 43 28 85 57 43 28 85 57 43 28 85 57 43 28
(lpm)
Torque (Nm) 2,100 4,100 6,500 10,100 2,900 5,300 8,100 12,500 3,700 6,400 9,700 14,800 4,600 7,800 11,400 17,500
170
Speed (rpm) 121 80 60 40 121 80 60 40 121 80 60 40 121 80 60 40
1st gear (parallel mode), 2nd gear (parallel + 2-speed mode), 3rd gear (serial mode), 4th gear (serial + 2-speed mode)
Torque (Nm) 3,400 6,600 9,600 14,700 4,400 8,200 11,800 18,000 5,500 9,900 14,000 21,200
120
Speed (rpm) 61 41 31 20 61 41 31 20 61 41 31 20
(lpm)
Torque (Nm) 2,900 5,700 9,000 14,100 4,000 7,300 11,200 17,300 5,100 8,900 13,400 20,600
170
Speed (rpm) 87 58 43 29 87 58 43 29 87 58 43 29
1st gear (parallel mode), 2nd gear (parallel + 2-speed mode), 3rd gear (serial mode), 4th gear (serial + 2-speed mode) Intermittend mode (max. 10% per minute)
between 200 bar and 240 bar
Drifter HB50
Dimensions
Drifter HB50
HB50 drilling 152.4 mm casings 25 m deep for strand anchors Flushing head (swivel) with male thread
Materials Services
Infrastructure
TKINF.223.e.1.0,2.08-20.DS