Professional Documents
Culture Documents
GM8806A-PL User Manual
GM8806A-PL User Manual
USER
R’’ S M A N U A L
G M 8 8 0 6 A - P L 11 0 1 0 1
48010609 22101 0
©2011,Shenzhen General Measure Technology Co.,
Ltd reserve all copyright.
Without permission from Shenzhen General Measure
Technology Co., Ltd,Any corporations or person must not
copy, spread, record or translate into other language by any
forms.
Our company reserved the right to update user’s
manual without additional notice to make perfect for
customers. Thus please visit our website or contact with our
service person to get update information.
Website:http://www.szgmt.com
GB/T 7724
Approved standard:GB/T 7724——2008
Table
1 General Information............................................................1
1.1 Function.........................................................................1
1.2 Description.................................................................... 2
1.3 Rear illustration............................................................ 3
1.4 Specification..................................................................4
1.5 Dimension..................................................................... 5
2 Wiring................................................................................... 6
2.1 Installation..................................................................... 6
2.2 Power connection........................................................ 7
2.3 Load cell connection....................................................7
2.3.1 Six wires...............................................................7
2.3.2 Four wires............................................................ 8
2.4 I/O terminals..................................................................9
2.5 Analog output connection......................................... 10
2.6 Serial port connection................................................11
3 Calibration......................................................................... 12
3.1 Instruction....................................................................12
3.2 Flow chart....................................................................13
3.3 Millivolt display........................................................... 16
3.4 Calibration without weights.......................................17
3.5 Quick zero/gain calibration....................................... 19
3.6 Parameter table..........................................................19
3.7 Parameter record....................................................... 19
4 Parameter setting............................................................. 20
4.1 Defination.................................................................... 20
4.2 Operation parameter table....................................... 22
5 Recipe setting................................................................... 25
5.1 Recipe number........................................................... 25
5.2 Recipe configuration..................................................25
5.3 Recipe parameter table.............................................26
6 Operation........................................................................... 36
6.1 Operating status.........................................................36
6.2 Batching times setting............................................... 36
6.3 Sort batching in turn.................................................. 37
6.4 Check and clear accumulative total........................ 38
6.5 Manual discharging................................................... 39
6.6 Manual zeroing...........................................................39
6.7 Restore for broken power......................................... 39
6.8 Compensation............................................................ 39
6.9 Free fall compensation..............................................40
6.10 Discharging monitor................................................ 40
6.11 Batching monitor...................................................... 40
6.12 I/O testing..................................................................41
6.13 I/O defination............................................................ 42
6.14 Display testing..........................................................45
6.15 Reset......................................................................... 46
6.16 Backup...................................................................... 47
6.17 Restore backup........................................................47
6.18 Analog calibration & self-definition........................48
6.18 .1 Analog calibration.....................................48
6.18.1
6.18..2 Analog self-definition................................50
6.18
6.19 Password.................................................................. 51
6.20 Password setting..................................................... 51
6.2
6.211 Operation mode..................................................52
7 Automatical batching........................................................53
7.1 Sketch map.................................................................53
7.2 Description.................................................................. 53
8 Serial port communication...............................................55
8.1 RS protocol................................................................. 55
8.2 RE protocol................................................................. 78
8.3 MODBUS protocol..................................................... 80
9 Error and alarm message............................................. 105
GM8806A -PL Batching controller
GM8806A-PL
1 General information
GM8804A-PL batching controller is a kind of weighing
control instruments to control automatic batching machine at
high accuracy and powerful function, which widely used in
various batching systems for concrete, bitumen, fertilizer,
feeding stuff and so on.
1.1 Function
� Small volume, unique design, easy operation;
� Suit to all of load cells at bridge-type resistance strain
gauge;
� 14 I/O
I/O( 4 input / 10 output)
� RS232/RS485 to ensure stable communication;
� Fast, moderate and slow feeding with “Jog feeding” ;
� Multi digital filter;
� Automatical modify for free fall;
� High precision 16bit DA analog output;
� Automatical compensation
� Digital calibration with or without weights;
� Password for calibration, operation parameters etc.;
� Automatic zeroing when power up;
� Automatic zero tracking.
� Three operation modes(optional).
GM8806A-PL1100101
GM8806A-PL11 -1-
GM8806A -PL Batching controller
GM8806A-PL
1.2 Description
P 1-1
Keypad
:Display value when zeroing or exit present function.
:Parameters are optional.
:Set parameter mode.
:Enter parameters or calibration or confirmation.
Status indication:
:Light in batching.
/ :Both SP1 and SP2 light in fast feeding;SP1 SP1
SP2 light in slow feeding.
light in moderate feeding;SP2
:Light in discharging.
:Light for zero when weight is among 0±1/4d 1/4d.
:Light for stability when weight is in stable range.
Display:
Main display
display:6digits, display weight and parameters.
Sub-display
Sub-display:6digits, display G.W. and parameters.
Set point display
display:1 digit, display batching numbers.
-2- GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
P 1-2
1 I/O input terminals
2 I/O output terminals
3 Load cell terminals
4 Serial port / analog terminals
5 Power connection
6 Fuse socket
GM8806A-PL1100101
GM8806A-PL11 -3-
GM8806A -PL Batching controller
GM8806A-PL
1.4 Specification
Common:
AC90V
Power supply:AC90V 260V 50Hz (or 60Hz) ± 2%
AC90V~260V
Inside
Filter:Inside
-10
Working temperature:-10 40
-10~40
40℃
90%R.H without dew
Max humidity:90%R.H
About 10W
Power consumption:A
105
Dimension:105
105××151
151××57mm
Analog:
DC5V 300mA (Max)
Load cell power:DC5V
10M
Input impedance:10M
10MΩΩ
0.02
Zero steady range:0.02 9mV
0.02~9mV
0.01uV/d
Input sensitivity:0.01uV/d
0.2
Gain input range:0.2 10mV
0.2~10mV
Sigma - Delta
Transfer mode:Sigma
120times
A/D conversion speed:120times
120times/sec
0.01%F.S
Non-linearity:0.01%F.S
10PPM/
Gain drift:10PPM/
10PPM/℃
1/30000
Display Precision:1/30000
Digital:
6digits red high-brightness LED
Weight display:6digits
Minus display:“-”
OFL
Overload display:“OFL
OFL”
5kinds (optional)
Decimal point:5kinds
-4- GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
1.5 Dimension
GM8806A-PL1100101
GM8806A-PL11 -5-
GM8806A -PL Batching controller
GM8806A-PL
2 Wiring
2.1 Installation
3. Install indicator in
the front of control box.
4. Insert mounting
plates on both sides
and then screw tightly.
P 2-1
-6- GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
P 2-2
1) 6 wires connection:
P 2-3
GM8806A-PL1100101
GM8806A-PL11 -7-
GM8806A -PL Batching controller
GM8806A-PL
2) 4 wires connection
P 2-4
-8- GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
P 2-5
P 2-6
Indicator output terminal connection:
GM8806A-PL1100101
GM8806A-PL11 -9-
GM8806A -PL Batching controller
GM8806A-PL
P 2-7
I/O tolerant definition as follows:
Output Input
Manual
OUT1 Mater ial no. 1 IN1
dischar ging
OUT2 Mater ial no. 2 IN2 Run
OUT3 Mater ial no. 3 IN3 Pause
OUT4 Mater ial no. 4 IN4 St op
OUT5 Fast feeding
OUT6 Moderat e feeding
OUT7 Slow feeding
OUT8 Discharging
OUT9 Over tolerance
OUT10 Run
2.5 Analog output connection
Analog output two kinds: voltage and electric current.
For voltage output, 0-5V/0-10V/-5-5V/-10-10V is optional
for voltage output;4-20mA/0-20mA/0-24mA is optional for
electric current output. Define terminals as follows:
- 10 - GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
P 2-8
Note : Analog output is optional function, please declare if
need when place orders.
2.6 Serial port connection
Serial port(RS485 or RS232) connection as follows:
P 2-9
RS232 connection:
P 2-10
RS485 connection:
GM8806A-PL1100101
GM8806A-PL11 - 11 -
GM8806A -PL Batching controller
GM8806A-PL
Controller 1 A A
Computer
B B
GND GND
.
.
. GND is ground of RS 4 8 5 , it can very
mu c h imp ro v e c o mmu n ic a tio n
A quality via connecting with GND by
Controller n
GND
P 2-11
3 Calibration
3.1 Instruction
GM8806A-PL batching controller need calibrate at
beginning of operation or changing any parts on weighing
system or non-suitable application for user. The calibration
can define radix point, minimum scale division, maximum
scale capacity, zero and gain, etc.
User can press to enter next or press to
save setting to only change one parameter, and then
press to exit.
- 12 - GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
Input correct
password , when
CAL ON
display “CAL ON” one
second, then enter to
set radix point
automatically.
GM8806A-PL1100101
GM8806A-PL11 - 13 -
GM8806A -PL Batching controller
GM8806A-PL
- 14 - GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
- 16 - GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
GM8806A-PL1100101
GM8806A-PL11 - 17 -
GM8806A -PL Batching controller
GM8806A-PL
- 18 - GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
4 Parameter setting
4.1 Defination
Press to select parameters, then press and
to set parameters, after that, press to save
setting.
1)Optional
Optional parameter setting
ON
Set“parameter 5 ”(ON
ON)for example:
- 20 - GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
1. Press 5”
, sub-display sparkle “5
in the left.
2. Press 3”,
till sub-display show “3
then press ,sparkle move to the
right one.
3. Press 5”,
till sub-display show“5
then press to save and finish.
GM8806A-PL1100101
GM8806A-PL11 - 21 -
GM8806A -PL Batching controller
GM8806A-PL
1 01 99
01~99 01 Scale no.
1200~57
2 9600 Baud rate
600
Communication mode:
Read/Cont are optional in
Rs/Re
3 Rs item 3.1 for Rs/Re mode;
/Bus
Rtu/Asc is optional in item
3.1 for Bus mode.
Rs/Re mode:
Read/Co READ
READ:command;
3.1 Cont
nt
CONT
CONT:continue
MODBUS communication
3.1 Rtu/Asc Rtu
mode: Rtu or Asc
- 22 - GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
Data format:
18N2 18N2
18N2: (R / C / B_r optional);
18E1 18E1
18E1: (R / C / B_r optional);
18O1
18O1:(R / C / B_r optional);
18O1
4 18N1 18E1
18N1
18N1: (R / C / B_r optional);
17N2
17E1 17N2
17N2: (RR / C optional);
17O1 17E1
17E1: (RR / C optional);
17O1:(R
17O1 R / C optional).
Zeroing range(01%~99% of
7 01 99
01~99 50
full capacity).
Zeroing/tare-off operation
b_zero / before batching:
11 b_zero
b_tare b_tare
b_tare:tare off;
b_zero
b_zero:zeroing.
GM8806A-PL1100101
GM8806A-PL11 - 23 -
GM8806A -PL Batching controller
GM8806A-PL
- 24 - GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
5 Recipe setting
Leading quantity of
moderate feeding for
material no.1;In faxed
1.A3 xxxxxx 000000 value,if weight ≥ target
value - leading quantity of
fast feeding,then moderate
feeding stop.
Free fall value of material
no.1;In faxed value,if
1.A4 xxxxxx 000000 weight ≥ target value – free
fall value,then slow feeding
stop.
Target value of material
1.b1 xxxxxx 000000
2.
no.2
- 26 - GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
No contrast time t3 in
moderate feeding:
When moderate feeding
within time t3, the batching
00.0 99. 9
00.0~99.
F2.3 00.5 controller don’t contrast
seconds present weight with the
value (target value - leading
quantity of moderate
feeding).
GM8806A-PL1100101
GM8806A-PL11 - 29 -
GM8806A -PL Batching controller
GM8806A-PL
Feeding mode:
ON
ON:Fast, moderate and
slow feeding individually.
Press to enter F3.1
F3.1;
F3 ON/ OF F OF F
press F4..
to enter F4
OFF
OFF:Fast, moderate and
slow feeding together.
Press or F4..
to F4
Over/under tolerance
alarm:
ON
ON:press to enter
F4 ON/ OF F OF F F4.1;press to enter F5
directly;
OFF: press or to
enter F5 directly.
GM8806A-PL1100101
GM8806A-PL11 - 31 -
GM8806A -PL Batching controller
GM8806A-PL
Discharging-controlled
switch:
ON
ON:Press to enter
F6.1
F6.1;Press to enter F7
F6 ON/OFF OFF
directly.
OFF
OFF:Press or to
enter F7 directly,Initial as
OFF..
F6.1=F6.2= OFF
Discharging mode switch:
ON
ON:Discharge directly after
batching one kind of
F6.1 ON/OFF OFF
material.
OFF
OFF:Discharge when all of
material batching finished.
Discharging-permited
switch:
ON
ON:Discharge till received
F6.2 ON/OFF OFF
discharging signal.
OFF
OFF:Discharge directly
when finish batching.
Supplement switch:
ON
ON:Press to enter
F7 ON/OFF OFF F7.1
F7.1;Press to enter F8
directly.
OFF
OFF:Press or to
enter F8 directly.
GM8806A-PL1100101
GM8806A-PL11 - 33 -
GM8806A -PL Batching controller
GM8806A-PL
Jog-feeding supplement
times for under tolerance. If
F7.1 00 99
00~99 03
the weight is still under
tolerance, then stop directly.
00.0 99. 9
00.0~99. Jog-feeding supplement
F7.2 00.5
seconds effective time.
00.0 99. 9
00.0~99. Jog-feeding supplement
F7.3 00.5
seconds alternation time.
Jog-feedingoutput time:
00.0 99. 9
00.0~99.
F8.2 00.5 Slow feeding ineffective
seconds
time tb every time.
In stop status,sub-display:
dsp_re
dsp_re:Recipe no.;
dsp_DA
dsp_DA:Analog;
sdp_DA/
F9 dsp_re rdp_s1
rdp_s1:Accumulative total
sdp_re
for present material;
rdp_s3
rdp_s3:Total feedling
value.
- 34 - GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
Batching compositor
switch:
ON
ON:Press to enter
F11 ON/OFF OFF F11.1
F11 .1;Press to enter
F1
F122 directly.
OFF
OFF:Press or to
F1 2
enter F12 directly.
GM8806A-PL1100101
GM8806A-PL11 - 35 -
GM8806A -PL Batching controller
GM8806A-PL
6 Operation
6.1 Operation status
1. When power on, buzzer hoot, main and sub-display
flash “8”,and instruction lights also sparkle.
2. After finished, main display
show “8806-P” , and sub-display
show “software no. ”.
3.(1)When operation parameter
no. 14=OFF or F14=ON power off in
stop status, batching controller show
present weight after display working mode and software no.
within 3 seconds.
(2)When operation parameter
14=ON and power off in running
no.14=ON
status, main display show gross weight, sub-display
show“Conti?” after display working mode and software no.
within 3 seconds. ID no. is material no. before power off,
such as right chart, material lno.3 is batching when power
off.
3” as follows:
For example, set batching times “3
- 38 - GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
Press tStio
8 times till main-display show“tStio
tStio”.
Sub-display indicate
F means IN1~IN4
Press , from left to right,
main-display when input
show“inPUt” effectively, F change
to O.
For example, F
change to O indicates
IN1 input effectively
Press to
and connect correctly.
enter I/O
input testing. OUTPUT means
testing. Main-display
show output number,
Press , sub-display show
main-display status.
oUtPUt
show“oUtPUt
oUtPUt”
Press ,sub-display
OFF change to ON
indicates OUT1 output
effectively and connect
correctly.
Press to Press to switch
enter I/O output numbers, such
output testing. as from OUT1 to
OUT2
OUT2.
GM8806A-PL1100101
GM8806A-PL11 - 41 -
GM8806A -PL Batching controller
GM8806A-PL
Input
Co d e Defi n i ti on Descri pt i on
Enter run status when impulse
I1 Start
input is effective.
Return to stop status when
I2 Stop
impulse input is effective.
Zeroing for gross weight when
I3 Zero
impulse input is effective.
Clear alarm when impulse input
I4 Clear alarm
is effective.
40.. If target value
Recipe no. 1 to 40
I5 Recipe no.
is 0, then go to next one.
GM8806A-PL1100101
GM8806A-PL11 - 45 -
GM8806A -PL Batching controller
GM8806A-PL
6.15 Reset
Reset present parameters to initial setting.
io
Reset “I/O definition (io
io)” for example:
1. In stop status, press till main
display show “init”.
3. Press io
till sub-display show“io
(I/O definition”.
SETUP
Note: “SETUP
SETUP”to backup operation
CAL
parameters; “CAL
CAL”to backup calibration
rECiPE
parameters; “rECiPE
rECiPE”to backup recipe
parameters; “ALLALL
ALL”to reset all of
parameters.
4. Press , sub-display
YES?
show“YES?
YES?”.
5. Press , sub-display
SUCCES
show“SUCCES
SUCCES”to enter next
parameters. Press to return.
- 46 - GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
6.16 Backup
User can make all of parameters backup.
ALL
Make“all of parameters (ALL
ALL)”backup for example:
1. When stop , press till main
display show bAC
bAC””.
“bAC And then
press input calibration password,
sub-display show “SET UP
UP””.
2. Press ALL
till sub-display show“ALL
(all of parameters)”
SETUP
Note: “SETUP
SETUP” operation parameters
CAL
backup; “CAL
CAL”calibration parameters
io
backup; “io
io”I/O definition backup.
rECiPE
“rECiPE
rECiPE”recipe parameters backup.
3. Press YES?
, sub-display show“YES?
YES?”,
then press to confirm and enter
next parameters. Otherwise
press to exit and return stop status.
GM8806A-PL1100101
GM8806A-PL11 - 47 -
GM8806A -PL Batching controller
GM8806A-PL
- 48 - GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
2. Press 12mA,,
to calibrate 12mA
which ID indicate from 1 to 2;
Calibrate 20mA when ID indicate
3; If no ID indication, it calibrates
maximum current.
Calibration method:
1. Please connect multi-meter with analog output terminals
correctly in calibration.
2.If the analog output value from multi-meter and terminals
are different, press , so sub-display sparkle, and then
press or to change DA digits and adjust analog
output value to be same as calibration value, after that,
press to finish.
3. If the analog output value from multi-meter and terminals
are same, press to next calibration item.
4.No need adjust DA digits to calibrate maximum analog,
only input analog value from multi-meter in the calibration.
6. Press to exit.
GM8806A-PL1100101
GM8806A-PL11 - 49 -
GM8806A -PL Batching controller
GM8806A-PL
6.19 Password
All initial passwords are :000000
000000
000000。
Note:Calibration password is same password as reset,
backup, restore, I/O definition and analog calibration. When
calibration password changed, others also changed.
Password operation as follows
1. Press to enter password.
2. Press to input password.
Note: If input wrong,sub-display
Error
show“Error
Error”, then press again. If
input wrong for three times, main display
Error4
show“Error4
Error4”and self-lock, but user can
operate again when power on again.
3. Input correct password, then
press to set parameters.
6.20 Password setting
ON
User can set password in parameters when F6.1 is“ON
ON”.
Set operation parameters password for example:
1.When operation parameter 16 set
ON
ON,press ,main display show
16.
6.11,then press , main display
show PASS
PASS, enter password.
2. Press and in turn to input
password.
Note: User must input same new
passwordtwice to set password. If not
Error
same, main display show“Error
Error”one
second and return to PASS again.
3. Once input same new password
twice, press to save and return
16.1.
GM8806A-PL1100101
GM8806A-PL11 - 51 -
GM8806A -PL Batching controller
GM8806A-PL
- 52 - GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
7.2 Description
1)When power on, indicator begin batching process.
(If setwrong parameters, indicator will show ERROR8).
Ingredient weight ≥ target value - leading quantity of fast
feeding, shut fast feeding.
GM8806A-PL1100101
GM8806A-PL11 - 53 -
GM8806A -PL Batching controller
GM8806A-PL
- 54 - GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
Here:
STX —— 1bit,start character 02H
Scale no. —— 2bits,range at 01-99
01-99,For example: 01 is
30H 31H
R —— 1bit,52H
52H
53H
S —— 1bit,53H
Ingredient no. —— 2bits
2bits,range at 00~04
00~04(30H 30H~30H
34H).. 00 means stop status.
34H
State 1 —— 1bit
GM8806A-PL1100101
GM8806A-PL11 - 55 -
GM8806A -PL Batching controller
GM8806A-PL
Bit 0 1 2 3 4 5 6 7
Before Fast Moderate Slow
1 Run Pause 1
feeding feeding feeding feeding
G/N —— 1bit
Bit 0 1 2 3 4 5 6 7
1 Net 0 0 0 0 0 1
0 Gross
Wrong response:
STX Scale no. R T N O CRC CR LF
Here:
T —— 1bit 54H
1bit,54H
Total times —— 4bits 0000~9999
4bits,0000~9999
,—— 1bit 2CH
1bit,2CH
Accumulative total —— 10bits
10bits,including decimal point
# —— 1bit 23H
1bit,23H
N —— 1bit 4EH
1bit,4EH
O —— 1bit 4FH
1bit,4FH
1 for example:
Read accumulative total command from no.1
02 30 31 52 54 36 35 0D 0A
Correct response:
02 30 31 52 54 30 30 31 30 2C 30 30 30 30 30 32 30 33 36
38 30 31 0D 0A
02 30 31 31 23 30 30 31 30 2C 30 30 30 30 30 30 37 34 34
38 32 33 0D 0A
02 30 31 32 23 30 30 31 30 2C 30 30 30 30 30 30 34 36 31
36 31 38 0D 0A
02 30 31 33 23 30 30 31 30 2C 30 30 30 30 30 30 35 34 34
34 31 39 0D 0A
02 30 31 34 23 30 30 31 30 2C 30 30 30 30 30 30 32 38 36
30 31 39 0D 0A
Means total times 10
10,accumulative total 20368 1、no.2
20368,no.1 no.2、
no.3 no.4 tatal value is:7448
no.3、no.4 7448 4616
7448,4616 5444 and 2860.
4616,5444
- 58 - GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
Correct response:
Scale Ingredient Recipe
STX R R DDDDDD CRC CR LF
no. no. parameters
Wrong response
STX Scale no. R R N O CRC CR LF
Here:
Ingredient no. —— 2bit , such as Ingredient no. 1 is 30H
31H
Recipe parameters —— 1bit
1bit,0 0:30H
30H target value,11:31H
31H
leading quantity of fast feeding,22:32H
32H
leading quantity of moderate feeding,3 3:
33H free fall value,, 4:34H near-zero value..
DDDDDD —— 6bits6bits,recipe parameter values
GM8806A-PL1100101
GM8806A-PL11 - 59 -
GM8806A -PL Batching controller
GM8806A-PL
Correct response:
STX Scale no. R F Parameters DDDDDD CRC CR LF
Wrong response:
STX Scale no. R F N O CRC CR LF
Here:
F —— 1bit 46H
1bit,46H
Parameters —— 3bits
3bits,such as feeding time delay F2.1 is
32H 31H 30H
DDDDDD —— 6bits
6bits,recipe parameter values
1 command:
Read parameter F2.1 from scale no.1
02 30 31 52 46 32 31 30 39 38 0D 0A
Correct response:
02 30 31 52 46 32 31 30 30 30 30 30 35 30 34 33 0D 0A
1 in scale no.1
Means parameter F2.1 of ingredient no.1 1 is 5.0
� Host computer read“Batching value”
Read command:
STX Scale no. R O ingredient no. 0 CRC CR LF
Correct response:
Scale Ingredient
STX R O 0 DDDDDD CRC CR LF
no. no.
Wrong response:
STX Scale no. R O N O CRC CR LF
Here:
4FH
O —— 1bit,4FH
2bits(1~4 optional),such as Ingredient
Ingredient no. —— 2bits
- 60 - GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
no 1(30H
30H 31H
31H)
0 —— 1bit 30
1bit,30
30H
DDDDDD —— 6bits
6bits,batching value
Here:
42H
B —— 1bit,42H
DDDDDD —— 6bits
6bits,batching times value
Wrong response:
STX Scale no. R N N O CRC CR LF
- 62 - GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
Here:
N —— 1bit 4FH
1bit,4FH
DDDDDD —— 6bit
6bit,receipe no.
Here:
E —— 1bit 45H
1bit,45H
6bits,if it is conti status..
DDDDDD —— 6bits
For examples:
02 30 31 52 45 35 30 0D 0A
Correct response:
02 30 31 52 45 30 30 30 30 30 31 33 39 0D 0A
conti
Means scale no. 1 is in“conti
conti?”status.
GM8806A-PL1100101
GM8806A-PL11 - 63 -
GM8806A -PL Batching controller
GM8806A-PL
Correct response:
STX Scale no. W R O K CRC CR LF
Wrong response:
STX Scale no. W R N O CRC CR LF
- 64 - GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
Here:
W —— 1bit 52H
1bit,52H
Ingredient no. —— 2bit
2bit, such as Ingredient no. 1 is 30H
31H
Recipe parameter —— 1bit 0:30H
1bit,0 30H target value 1:31H
value,1 31H
2:32H
leading quantity of fast feeding,2 32H
3:33H
leading quantity of moderate,3 33H free
fall value;; 4:34H
34H near-zero value.
DDDDDD —— 6bit,recipe parameter value
1500 for Ingredient no.1 in
For example:Write target value=1500
scale no.1
02 30 31 57 52 30 31 30 30 30 31 35 30 30 30 37 0D 0A
Correct response:
02 30 31 57 52 4F 4B 32 32 0D 0A
Means scale no. 1 has saved the weight value.
� Host computer set“Recipe parameter”
Write command:
Scale Set
STX W F DDDDDD CRC CR LF
no. parameter
Correct response:
STX Scale no. W F O K CRC CR LF
Wrong response:
STX Scale no. W F N O CRC CR LF
Here:
F —— 1bit 46H
1bit,46H
GM8806A-PL1100101
GM8806A-PL11 - 65 -
GM8806A -PL Batching controller
GM8806A-PL
Correct response:
STX Scale no. W U O K CRC CR LF
Wrong response:
STX Scale no. W U N O CRC CR LF
Note:Not permit to write command on communication
parameters.
Here:
U —— 1bit 55H
1bit,55H
3bit,such as :zeroing range 7 is
Operation parameter —— 3bit
37H 30H 30H
0 —— 1bit 31H
1bit,31H
DDDDDD —— 6bit 6bit,operation parameter value
For example:Write 30 command on operation parameter 7
1:
in scale no.1:
- 66 - GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
02 30 31 57 55 37 30 30 30 30 30 30 30 33 30 36 31 0D 0A
Correct response:
02 30 31 57 55 4F 4B 32 35 0D 0A
Means scale no. 1 has saved operation parameter 7.
� Host computer write“Recipe no.”(only in stop status)
Write command:
STX Scale no. W N DD CRC CR LF
Correct response:
STX Scale no. W N O K CRC CR LF
Wrong response:
STX Scale no. W N N O CRC CR LF
Here:
DD —— 2bits
2bits,range at 01-40
01-40,which is recipe no.
01 on scale no. 1 command:
For example: Write recipe no. =01
02 30 31 57 4E 30 31 36 31 0D 0A
Correct response::
02 30 31 57 4E 4F 4B 31 38 0D 0A
Means scale no.1 has saved recipe no.
� Host computer write“Batching times”(only in stop
status)
Write command:
STX Scale no. W B DDDDDD CRC CR LF
Correct response:
STX Scale no. W B O K CRC CR LF
GM8806A-PL1100101
GM8806A-PL11 - 67 -
GM8806A -PL Batching controller
GM8806A-PL
Wrong response:
STX Scale no. W B N O CRC CR LF
Here:
B —— 1bit
1bit,42H
DDDDDD —— 6bits
6bits,range at 000000-009999
000000-009999,which is
batching times
1000 on scale no.1:
For example:Write batching times=1000
02 30 31 57 42 30 30 31 30 30 30 34 31 0D 0A
Correct response:
02 30 31 57 42 4F 4B 30 36 0D 0A
Means scale no. 1 has saved batching times.
� Host computer write“Restor for broken power”
Write command:
STX Scale no. W E D CRC CR LF
Correct response:
STX Scale no. W E O K CRC CR LF
Wrong response:
STX Scale no. W E N O CRC CR LF
Here:
E —— 1bit 45H
1bit,45H
1bit,range at 0 and 1,1
D —— 1bit 1 means to restore;; 0
means not to restore.
For example:Write restore 01 command on scale no.1:
02 30 31 57 45 31 30 34 0D 0A
- 68 - GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
Correct response:
02 30 31 57 45 4F 4B 30 39 0D 0A
Means the command has been saved.
� Host computer calibrate“decimal point”
Write command:
Decimal
STX Scale no. C P CRC CR LF
point
Correct response:
STX Scale no. C P O K CRC CR LF
Wrong response:
STX Scale no. C P N O CRC CR LF
Here:
C —— 1bit 43H
1bit,43H
P —— 1bit 50H
1bit,50H
Decimal point —— 1bit
——1bit
1bit,range at 0~4
1:
For example:Calibrate decimal point 3 on scale no.1:
02 30 31 43 50 33 39 37 0D 0A
Correct response:
02 30 31 43 50 4F 4B 30 30 0D 0A
Means scale no.1 has saved decimal point value.
� Host computer“Add weights to calibrate zero”
Write command:
STX Scale no. C Z CRC CR LF
Correct response:
STX Scale no. C Z O K CRC CR LF
GM8806A-PL1100101
GM8806A-PL11 - 69 -
GM8806A -PL Batching controller
GM8806A-PL
Wrong response:
STX Scale no. C Z N O CRC CR LF
Here:
Z —— 1bit 5AH
1bit,5AH
For example:Add weights to calibrate zero on scale no.1
02 30 31 43 5A 35 36 0D 0A
Correct response:
02 30 31 43 5A 4F 4B 31 30 0D 0A
Means command has been performed.
� Host computer“calibrate zero without weights”
Write command:
STX Scale no. C Y DDDDDD CRC CR LF
Correct response:
STX Scale no. C Y O K CRC CR LF
Wrong response:
STX Scale no. C Y N O CRC CR LF
Here:
Y —— 1bit 59H
1bit,59H
DDDDDD —— 6bits
6bits,which is millivolt value related zero.
Here:
4DH
M —— 1bit,4DH
DD —— 2bits,individually 1、2
2、5
5、10
10 20
10、20 50
20、50
DDDDDD —— 6bits
6bits,maximum capacity value
For example:Write division and maximum capacity
command on scale no.1
02 30 31 43 4D 30 31 30 31 30 30 30 30 32 39 0D 0A
Correct response:
02 30 31 43 4D 4F 4B 39 37 0D 0A
Means scale no.1 has saved written value.
� Host computer“Add weights to calibrate gain”
Write command:
STX Scale no. C G DDDDDD CRC CR LF
Correct response:
STX Scale no. C G O K CRC CR LF
GM8806A-PL1100101
GM8806A-PL11 - 71 -
GM8806A -PL Batching controller
GM8806A-PL
Wrong response:
STX Scale no. C G N O CRC CR LF
Here:
G —— 1bit 47H
1bit,47H
DDDDDD —— 6bit
6bit,gain value
For example:Calibrate gain 10000 command on scale no. 1
02 30 31 43 47 30 31 30 30 30 30 32 36 0D 0A
Correct response:
02 30 31 43 47 4F 4B 39 31 0D 0A
Means scale no.1 has saved 10000.
� Host computer“calibrate gain without weights”
Write command:
Correct response:
STX Scale no. C L O K CRC CR LF
Wrong response:
STX Scale no. C L N O CRC CR LF
Here:
L —— 1bit 4CH
1bit,4CH
D1D1D1D1D1D1 —— 6bits
6bits,gain millivolt value
D2D2D2D2D2D2 —— 6bits
6bits,gain weight value
For example:Calibrate gain without weights 4.110mV as
10000 on scale no. 1
02 30 31 43 4C 30 30 34 31 31 30 30 31 30 30 30 30 32 35
0D 0A
- 72 - GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
Correct response:
02 30 31 43 4C 4F 4B 39 36 0D 0A
Means scale no. 1 has saved calibration value.
� Host computer“Discharging operation”
Write command:
STX Scale no. C D CRC CR LF
Correct response:
STX Scale no. C D O K CRC CR LF
Wrong response:
STX Scale no. C D N O CRC CR LF
Here:
D —— 1bit 44H
1bit,44H
For example:Send discharging operation on scale no. 1
02 30 31 43 44 33 34 0D 0A
Correct response:
02 30 31 43 44 4F 4B 38 38 0D 0A
Means the command has been performed.
� Host computer“Running operation”
Write command:
STX Scale no. C R CRC CR LF
Correct response:
STX Scale no. C R O K CRC CR LF
Wrong response:
STX Scale no. C R N O CRC CR LF
GM8806A-PL1100101
GM8806A-PL11 - 73 -
GM8806A -PL Batching controller
GM8806A-PL
Here
R —— 1bit 52H
1bit,52H
For example:Run scale no. 1
02 30 31 43 52 34 38 0D 0A
Correct response:
02 30 31 43 52 4F 4B 30 32 0D 0A
Means the command has been performed
� Host computer“Stop operation”
Write command:
STX Scale no. C J CRC CR LF
Correct response:
STX Scale no. C J O K CRC CR LF
Wrong response:
STX Scale no. C J N O CRC CR LF
Here:
J —— 1bit 4AH
1bit,4AH
For example:Stop scale no. 1
02 30 31 43 4A 34 30 0D 0A
Correct response:
02 30 31 43 4A 4F 4B 39 34 0D 0A
Means the command has been performed.
� Host computer“Pause operation”
Write command:
STX Scale no. C S CRC CR LF
- 74 - GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
Correct response:
STX Scale no. C S O K CRC CR LF
Wrong response:
STX Scale no. C S N O CRC CR LF
Here:
S —— 1bit 53H
1bit,53H
For example:Pause scale no. 1
02 30 31 43 53 34 39 0D 0A
Correct response:
02 30 31 43 53 4F 4B 30 33 0D 0A
� Host computer“Tare-off operation”
Write command:
STX Scale no. C Q CRC CR LF
Correct response:
STX Scale no. C Q O K CRC CR LF
Wrong response:
STX Scale no. C Q N O CRC CR LF
Here:
Q —— 1bit 51H
1bit,51H
For example:Tare off on scale no. 1
02 30 31 43 51 34 37 0D 0A
Correct response:
02 30 31 43 51 4F 4B 30 32 0D 0A
GM8806A-PL1100101
GM8806A-PL11 - 75 -
GM8806A -PL Batching controller
GM8806A-PL
Here:
O —— 1bit 4FH
1bit,4FH
For example:Clear tare on scale no.1
02 30 31 43 4F 34 35 0D 0A
02 30 31 43 4F 4F 4B 39 39 0D 0A
Correct response:02
� Host computer“Clear alarm operation”
Write command:
STX Scale no. C B CRC CR LF
Correct response:
STX Scale no. C B O K CRC CR LF
Wrong response:
STX Scale no. C B N O CRC CR LF
Here:
B —— 1bit 42H
1bit,42H
For example:Clear alarm on scale no. 1
02 30 31 43 42 33 32 0D 0A
Correct response:0202 30 31 43 42 4F 4B 38 36 0D 0A
- 76 - GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
1
For example:Zeroing command on scale no.1
02 30 31 43 43 33 33 0D 0A
02 30 31 43 43 4F 4B 38 37 0D 0A
Correct response:02
� Host computer“Manual slow feeding operation”
Write command:
STX Scale no. C A CRC CR LF
Correct response:
STX Scale no. C A O K CRC CR LF
Wrong response:
STX Scale no. C A N O CRC CR LF
Here:
A —— 1bit 41H
1bit,41H
For example:Manual slow feeding command
02 30 31 43 41 33 31 0D 0A
02 30 31 43 41 4F 4B 38 35 0D 0A
Correct response:02
Note:The command is effective one time and ineffective
next time.
GM8806A-PL1100101
GM8806A-PL11 - 77 -
GM8806A -PL Batching controller
GM8806A-PL
8.2 RE protocol
Cont
Two modes:Continue (Cont Read
Cont)/ command (Read
Read).
Support all of data format in parameters F4.5; ASCII code.
Cont
1) Continue mode (Cont
Cont)
When operation parameters 3 for RE 3.1 for Cont
RE、3.1 Cont,
indicator send data to host computer without any command.
Data format as follows:
Status , GS , Sign Value Unit CR LF
Here:
OL
Status —— 2bits,OL ST
OL:( 4FH 4CH ) overflow;ST
ST:( 53H
54H )stable US
US:( 55H 53H )unstable
, —— 1bit,list separator 2CH
47H 53H
GS —— 2bits,47H
2BH
Sign —— 1bit,2BH 、2DH
2BH(+) 2DH
2DH(-)
Value
Value—— 7bits,including decimal point,if no, the highest
bit is 0
Kg 4BH 67H
Unit —— 2bits,Kg
0DH
CR —— 1bit,0DH
0AH
LF —— 1bit,0AH
For example:Indicator sends following data format:
53 54 2C 47 53 2C 2B 30 31 31 2E 31 32 30 4B 67 0D 0A
Means :stable、positive data、present weight value is 11.
120kg
- 78 - GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
Here:
R —— 52H
E —— 45H
A —— 41H
D —— 44H
CR —— 0DH
LF —— 0AH
Response data format is same as data format in continue
mode.
For example
Command: 52 45 41 44 0D 0A
53 54 2C 47 53 2C 2B 30 31 31 2E 31 32 30 4B
Response:53
67 0D 0A
Means:stable、positive data、present weight value is 11.
120kg..
120kg
GM8806A-PL1100101
GM8806A-PL11 - 79 -
GM8806A -PL Batching controller
GM8806A-PL
Ingredient 3 in fast
.6
feeding
Ingredient 3 in
.7
moderate feeding
Ingredient 3 in slow
.8
feeding
Ingredient 4 in fast
.9
feeding
Ingredient 4 in
.10
moderate feeding
Ingredient 4 in slow
.11
feeding
Bit Meaning
.0 0:Stop 1:Run
0:Not pause
.1
1:Pause
0:Unstable
.2
1:Stable
0:None zero
.3
1:Zero
Preset state
40002 0001 0:Not overflow
2 .4
1:Overflow
0:Not minus
.5
1:Minus
.6 Before feeding
Single ingredient
.7
feeding finished
Check over/under
.8
tolerance.
GM8806A-PL1100101
GM8806A-PL11 - 81 -
GM8806A -PL Batching controller
GM8806A-PL
.9 Alarm
.10 Fix value output
.11 Discharging
.X Reserve
When weight overflow,
40003 0002
Present indicator display OFL
OFL,
weight return value
40004 0003
0xFFFFFFFF..
0xFFFFFFFF
40005 0004 Accumulate Only read,when write,
40006 0005 total times return error data address.
40007 0006 Accumulate Only read,when write,
40008 0007 total weight return error data address.
40009 0008 Ingredient 1
Only read,when write,
accumulated
40010 0009 weight return error data address.
40042 0041
40043 0042 Read zero from the
Reserve
40044 0043 address.
40045 0044
Ingredient 2
40060 0059 leading
quantity of 1.b3
40061 0060 moderate
feeding
Ingredient 3
40062 0061 leading
quantity of 1.C3
40063 0062 moderate
feeding
Ingredient 4
40064 0063 leading
quantity of 1.d3
40065 0064 moderate
feeding
40066 0065
40067 0066 Read zero from the
Reserve
40068 0067 address.
40069 0068
40070 0069 Ingredient 1
1.A4
40071 0070 free fall data
40072 0071 Ingredient 2 Note : Written
1.b4
40073 0072 free fall data value must less
than or same as
40074 0073 Ingredient 3 maximum
1.C4
40075 0074 free fall data capacity.
40076 0075 Ingredient 4
1.d4
40077 0076 free fall data
40078 0077
40079 0078 Read zero from the
Reserve
40080 0079 address.
40081 0080
GM8806A-PL1100101
GM8806A-PL11 - 85 -
GM8806A -PL Batching controller
GM8806A-PL
Note : Written
40082 0081
value must less
Near-zero
1.e0 than or same as
value
40083 0082 maximum
capacity.
The following items are two bytes and are available to read
and write (write code 0x06
0x06,read code 0x03
0x03)
0000H
0000H:00bit
bit;
0001H
0001H:11bit
0002H
0002H:22bits
bits;
40096 0095 Decimal point
0003H
0003H:33bits
0004H
0004H:44bits
(Change only in stop).
0001H
0001H:11;0002H
0002H
0002H:2 2
Minimum 0005H
0005H:5 5;000AH
000AH
000AH:10 10
40097 0096
division 00014 20
00014:20 0032H
20;0032H
0032H:50 50
(Change only in stop).
0002H 2mV/V
0002H:2mV/V
40098 0097 Sensitivity 0003H 3mV/V
0003H:3mV/V
(Change only in stop).
No contrast time
0000H~03E7H
40100 0099 t2 of fast F2.2
(00.0~99.9
00.0~99.9
00.0~99.9)
feeding
GM8806A-PL1100101
GM8806A-PL11 - 87 -
GM8806A -PL Batching controller
GM8806A-PL
No contrast time
0000H~03E7H
40101 0100 t3 of moderate F2.3
(00.0~99.9
00.0~99.9
00.0~99.9)
feeding
No contrast time
0000H~03E7H
40102 0101 t4 of slow F2.4
(00.0~99.9
00.0~99.9
00.0~99.9)
feeding
Check
0000H~03E7H
40103 0102 tolerance F2.5
(00.0~99.9
00.0~99.9
00.0~99.9)
time t5
Fixed value 0000H~03E7H
40104 0103 F2.6
time t6 (00.0~99.9
00.0~99.9
00.0~99.9)
Discharging 0000H~03E7H
40105 0104 F2.7
time delay t7 (00.0~99.9
00.0~99.9
00.0~99.9)
Discharging
0000H~03E7H
40106 0105 monitor time F2.8
(00.0~99.9
00.0~99.9
00.0~99.9)
t8
Feeding
0000H~03E7H
40107 0106 monitor time F2.9
(00.0~99.9
00.0~99.9
00.0~99.9)
t9
Pause time t10
between fast
0000H~03E7H
40108 0107 feeding F3.1
(00.0~99.9
00.0~99.9
00.0~99.9)
moderate
feeding
Pause time t11
between
0000H~03E7H
40109 0108 moderate F3.2
(00.0~99.9
00.0~99.9
00.0~99.9)
feeding and
slow feeding
- 88 - GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
Over
0000H~0063H
40110 0109 tolerance F4.1
(0.0~9.9s)
percent
Under
0000H~0063H
40111 0110 tolerance F4.2
(0.0~9.9s)
percent
Over/under
0000H~03E7H
40112 0111 tolerance F4.4
(00.0~99.9
00.0~99.9
00.0~99.9)
alarm time
Free fall
0000H~0063H
40113 0112 compensation F5.1
(00~99)
times
Free fall
0000H~0063H
40114 0113 compensation F5.2
(00~99%)
range
Free fall 0 : 0% ; 1 :
40115 0114 compensation F5.3 100%;2:50%
100% 50%;
percent 3:25%
25%
Jog feeding 0000H~0063H
40116 0115 F7.1
times (00~99)
Jog feeding 0000H~03E7H
40117 0116 F7.2
effective time (00.0~99.9
00.0~99.9
00.0~99.9)
Jog feeding 0000H~03E7H
40118 0117 F7.3
ineffective time (00.0~99.9
00.0~99.9
00.0~99.9)
Jog feeding of
0000H~03E7H
40119 0118 slow feeding F8.1
(00.0~99.9
00.0~99.9
00.0~99.9)
effective time
Jog feeding of
0000H~03E7H
40120 0119 slow feeding F8.2
(00.0~99.9
00.0~99.9
00.0~99.9)
ineffective time
GM8806A-PL1100101
GM8806A-PL11 - 89 -
GM8806A -PL Batching controller
GM8806A-PL
0 : rdp_fi 1:
rdp_fi;1
Sub-display rdp_s1
rdp_s1;
40121 0120 F9
data when stop 2:rdp_s2
rdp_s2
rdp_s2;33:
rdp_s3
Sub-display Same as manual
40122 0121 F10
data when run setting
Ingredient
40123 0122 F11.1
compositor
40124 0123 Recipe no. 1~40
40125 0124
40126 0125
Read zero from the
40124 0126 Reserve
address.
40128 0127
40129 0128
Zero tracking 0000H~0063H
40130 0129 6
range (00~99)
0001H~0063H
40131 0130 Zeroing range 7
(01~99)
Stability 0001H~0063H
40132 0131 8
range (01~99)
0000H~0009H
40133 0132 AD filter 9
(0~9)
0000H~0009H
40134 0133 Stability filter 10
(0~9)
Ingredient
40135 0134 13 0001H~00004H
kinds
0000H~0007H
40136 0135 Analog mode 15
(0~7)
40137 0136
Read zero from the
40138 0137 Reserve
address.
40139 0138
- 90 - GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
Batching
40140 0139 0000H~270FH
times
Write:Initialization
( Change only in stop)
8800 initialize all
parameters;8801 8801
initialize calibration;
8802 initialize operation
Back up / parameters;8803 8803
40141 0140 Restore initial initialize recipe
setting parameters;8804 8804
initialize IO definition.
Back up: (The highest bit
change to 6);
Restore: (The highest bit
change to 7).
Return 0 to read.
Write:Only in stop
status. Write 1 to start
I/O testing;Write 0 to
Start / Stop
40142 0141 exit.
I/O testing
Read:1 1 for I/O testing
status.00 for none I/O
testing status.
Write: not permit.
( Change only in stop)
Read: Input IN1 ~ IN6
40143 0142 Input testing
from low bit to high bit, 1
for effective input, 0 for
ineffective input.
GM8806A-PL1100101
GM8806A-PL11 - 91 -
GM8806A -PL Batching controller
GM8806A-PL
- 92 - GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
GM8806A-PL1100101
GM8806A-PL11 - 93 -
GM8806A -PL Batching controller
GM8806A-PL
Compensation
00174 0173
switch
Jog feeding of
00175 0174 slow feeding
switch
Ingredient
00176 0175
compositor
Free fall
00177 0176
compensation
00178 0177
00179 0178
Read zero from the
00180 0179 Reserve
address.
00181 0180
00182 0181
Read:1 for effective,0
for ineffective;
00183 0182 Input state in1
Write:Not permit
(Change only in stop)
00184 0183 Input state in2 Write:Not permit
00185 0184 Input state in3 Write:Not permit
00186 0185 Input state in4 Write:Not permit
Read:From low to high
represent out1-out1 0,
out1-out10
Output state which 1 for effective,0
00187 0186
out1 for ineffective;
Write:Not permit
( Change only in stop)
Output state
00188 0187 Not permit to write
out2
- 94 - GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
Output state
00189 0188 Not permit to write
out3
Output state
00190 0189 Not permit to write
out4
Output state
00191 0190 Not permit to write
out5
Output state
00192 0191 Not permit to write
out6
Output state
00193 0192 Not permit to write
out7
Output state
00194 0193 Not permit to write
out8
Output state
00195 0194 Not permit to write
out9
Output state
00196 0195 Not permit to write
out10
Read zero from the
00197 0196 Reserve
address.
Read:Run = 1;Not run
00198 0197 Star t
=0
Read:Stop = 1;Not
00199 0198 Urgent stop
stop = 0
Read:Pause = 1;Not
00200 0199 Pause
pause = 0
Read:Zeroing = 1;
00201 0200 Zeroing
none zeroing = 0
Read:Clear = 1 ;Not
00202 0201 Clear alar m
clear = 0
GM8806A-PL1100101
GM8806A-PL11 - 95 -
GM8806A -PL Batching controller
GM8806A-PL
Clear
Read:Clear = 1;Not
00203 0202 accumulat ed
clear = 0
tot al
Read : always read
00204 0203 Select recipe
OFF( 0000H
OFF(0000H
0000H)
Manual Read:Effective
discharging/ discharging = 1;
00205 0204
dischar ging ineffective discharging
per mit =0
Lock keypad Read:keypad effective
00206 0205 (Change only =1
in stop) Keypad ineffective = 0
Tare- off Read : always read
00207 0206
input OFF(0000H)
Clear tar e Read : always read
00208 0207
input OFF(0000H)
3) Function code
01 read coil、03
codes:01 03 read register、05
05 force single coil、
16
06 preset single register、16
16( 10 Hex
Hex) preset several
registers.
◆ 01 read coil
Inquiry:Regulate coil start and quantities.
Response:
a) Every coil state in response message is corresponding
1=ON
to every data in data area;1=ON 0=OFF
1=ON;0=OFF
0=OFF。The LSB in
- 96 - GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
01 01 00 28 00 04 BD C1
Inquiry command:01
01 01 01 02 D0 49
Correct response:01 49(Coil 43- 40 related
0- 0- 1- 0)
state:0-
B. ASCII communication mode
mode:
Inquiry command:
Function Start Coil LRC
Start Address Stop
code address quantities parity
1byte 2byte 2byte 4byte 4byte 2byte 2byte
GM8806A-PL1100101
GM8806A-PL11 - 97 -
GM8806A -PL Batching controller
GM8806A-PL
Correct response:
Function Account Data LRC
Start Address Stop
code byte area parity
1byte 2byte 2byte 2byte 2byte 2byte 2byte
Inquirycommand: 3A 30 31 30 31 30 30 32 38 30 30 30 34
44 32 0D 0A
3A 30 31 30 31 30 31 30 32 46 42 0D 0A
Correct response:3A
(Coil 0- 0- 1- 0)
Coil 43- 40 related status:0-
� 03 read register
Inquiry:Regulate to read register start address and register
quantities.
Response:Regulate read register byte quantities, every
register relate 2bytes respectively;Message also has data
from every read register.
For example:read register 0007 0008
0007、0008
0008。
A. RTU communication mode
mode:
Inquiry command:
Inquiry
Function Start CRC
Address register
code address parity
quantity
1byte 1byte 2byte 2byte 2byte
Correct response:
Function Account Register Register CRC
Address
code byte (0007) data (0008) data parity
1byte 1byte 1byte 2byte 2byte 2byte
- 98 - GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
01 03 00 07 00 02 75 CA
Inquiry command:01
01 03 04 00 00 00 05 3A 30
Correct response:01 30(Register
0007
0007、0008 0(Hex
0008 respective data:0 Hex 0000H)、5
0000H
Hex:0000H 5(Hex
Hex
Hex:
0005H
0005H)
B. ASCII communication mode
mode:
Inquiry command:
Inquiry
Function Start LRC
Start Address register Stop
code address parity
quantity
1byte 2byte 2byte 4byte 4byte 2byte 2byte
Correct response:
Register Register
Function Account LRC
Start Address (0007) (0008) Stop
code byte parity
data data
1byte 2byte 2byte 2byte 2byte 2byte 2byte 2byte
Inquirycommand: 3A 30 31 30 33 30 30 30 37 30 30 30 32
46 33 0D 0A
3A 30 31 30 33 30 34 30 30 30 30 30 30
Correct response:3A
30 35 46 33 0D 0A register 0007
0A(register 0008 respective data :
0007、0008
0(Hex
Hex 0000H
Hex:0000H
0000H)、5
5(Hex
Hex 0005H
Hex:0005H
0005H)
◆ 05 force single coil
Force:Regulate force coil address;and one normal item in
force data area,regulate requested coil ON/ OFF state:
FF00 for ON
ON,0000H for OFF
OFF,other data is ineffective to coil.
GM8806A-PL1100101
GM8806A-PL11 - 99 -
GM8806A -PL Batching controller
GM8806A-PL
01 06 00 09 00 05 99 CB
Preset command:01
01 06 00 09 00 05 99 CB
Correct response:01 register 0009
CB(register
data 5(Hex
data:5 Hex 0005H))
0005H
Hex:0005H
B. ASCII communication mode
mode:
Preset command:
Preset
Function Preset LRC
Start Address register Stop
code data parity
address
1byte 2byte 2byte 4byte 4byte 2byte 2byte
GM8806A-PL1100101
GM8806A-PL11 - 101 -
GM8806A -PL Batching controller
GM8806A-PL
Correct response:
Preset
Function Preset LRC
Start Address register Stop
code data parity
address
1byte 2byte 2byte 4byte 4byte 2byte 2byte
3A 30 31 30 36 30 30 30 39 30 30 30 35 45
Presetcommand:3A
42 0D 0A
3A 30 31 30 36 30 30 30 39 30 30 30 35
Correct response:3A
0A(register 0009 data: 5(Hex
45 42 0D 0A Hex 0005H))
0005H
Hex:0005H
◆16
16 10 hex
16(10 hex)) Preset several registers
Preset:Regulate to preset register start address and preset
value.
Response:Return address, function code, start address and
preset register quantity.
For example:Preset 2 registers in weighing indicator 01:
start register is 0030. Preset value is 0001H and 7318H
A. RTU communication mode
mode:
Preset command:
Function Start Register Account Preset CRC
Address
code address quantity byte data parity
1byte 1byte 2byte 2byte 1byte 4byte 2byte
Correct response:
Function Start Register CRC
Address
code address quantity parity
1byte 1byte 2byte 2byte 2byte
01 10 00 1E 00 02 04 00 01 73 18 07 D5
Preset command:01
- 102 - GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
01 10 00 1E 00 02 21 CE
Correct response:01
B. ASCII communication mode
mode:
Preset command:
Function Start Register Account Preset LRC
Start Address Stop
code address quantity byte data parity
1byte 2byte 2byte 4byte 4byte 2byte 8byte 2byte 2byte
Correct response:
Function Start Register LRC
Start Address Stop
code address quantity parity
1byte 2byte 2byte 4byte 4byte 2byte 2byte
Preset command:3A 3A 30 31 31 30 30 30 31 45 30 30 30 32
30 34 30 30 30 31 31 43 39 36 31 38 0D 0A
Correctresponse: 3A 30 31 31 30 30 30 31 45 30 30 30 32
43 46 0D 0A
4) MODBUS communication error message
When weighing indicator check other error message
except parity code( CRC or LRC)
LRC),indicator will send
message to host computer, the highest in function code is 1,
which means function code from weighing indicator to host
computer is added 128 based on function code from host
computer(For example: read register command 03H will be
changed to 83H
83H).
Error code:
02
02: error data address;Received data address is not
permitted by weighing indicator.
03
03: error data;Inquiry data is not permitted by weighing
indicator.
GM8806A-PL1100101
GM8806A-PL11 - 103 -
GM8806A -PL Batching controller
GM8806A-PL
0040
For example:Host computer read coil (0040
0040) by function
code 03.
Error message format:
1)RTU communication mode:
Address Function code Error code CRC parity
- 104 - GM8806A-PL11
GM8806A-PL1100101
GM8806A -PL Batching controller
GM8806A-PL
GM8806A-PL1100101
GM8806A-PL11 - 105 -