Professional Documents
Culture Documents
ASBL Installation Instructions
ASBL Installation Instructions
The information contained in this installation instruction is a quick reference guide. For detailed system information refer
to the panel manufacturer's installation manual. This instruction will not address specific programming procedures.
GENERAL DESCRIPTION
This instruction applies to the model ASBL addressable low frequency MOUNTING REQUIREMENTS
(520Hz) sounder base, which is to be connected to a DCP Signaling Line
Circuit (SLC). The ASBL is to be used with the ALG-V, ALK-V, ACA-V, BOX MOUNTING
AIE-EA, ATG-EA, ATJ-EA, ALN-V, ACC-V, and ACD-V model sensors BASE
only. The ASBL provides an audible, low-frequency alarm in the immediate 3" OCT 4" OCT 4" SQR*
vicinity. Typical applications are "sleeping areas in hotels, apartments, ALL MODELS NO NO YES
etc."
CAUTION ! CAUTION !
To ensure proper operation If this base will be installed in
connect this base to a an existing operational
SPECIFICATIONS compatible Fire Control system, inform the operator
Model ASBL Panel only. Refer to panel and local authority that the
DCP Voltage Range instructions for proper system will be temporarily out
17 - 41VDC
connection and of service. Disconnect power
DCP Loop Idle Current 154uA compatibility. to the control panel before
DCP Loop Low Frequency Alarm installing the base.
154uA
Current
Aux. Power Supply Voltage 24VDC (16 - 33VDC)
Range
Aux. Power Supply Voltage CAUTION
24VDC (16 - 33VDC) Install the bases in this instruction in accordance with
Range FWR
applicable NFPA standards, local codes, and the
Auxiliary Idle Current 2.26mA authorities having jurisdiction. Failure to follow these
140mA @ 16VDC instructions may result in failure of the sensor and
Auxiliary Low Frequency Alarm
95mA @ 24VDC bases to initiate an alarm condition. Hochiki America
Current
72mA @ 33VDC is not responsible for sensors that have been
203mA @ 16VFWR improperly installed, tested, or maintained.
Auxiliary Low Frequency Alarm
149mA @ 24VFWR For testing and cleaning information refer to NFPA-72
Current FWR
92mA @ 33VFWR for Automatic Fire Detectors for installation guidelines,
Sound Pressure Level at 10ft. 85dB testing, and maintenance.
Maximum Humidy 93%RH (non-condensing)
Use "3M" Weatherban # 606 nonflammable sealing
compound to seal field wiring conduit openings in the
Operating Temperature Rang 32°F (0°C) - 100°F (38°C) mounting back box. Compliance with this request may
Storage Temperature -22°F (30°C) - 158°F (70°C) reduce the occurrence of the "STACK EFFECT".
Base Diameter 6.6"
Base Height (without sensor) 1.34" (not including terminal block)
Weight 0.455lb
ALG-V, ALK-V, ACA-V, AIE-EA,
Compatible Sensors ATG-EA, ATJ-EA, ALN-V, ACC-V &
ACD-V
* SEE SHEET 2 OF 2 FOR SPECIFIC BACK BOX REQUIREMENTS
AUX -
AUX -
AUX -
N I M Bd 5 8 LEVEL ERUSSERP DNUOS N I M Bd 5 8 LEVEL ERUSSERP DNUOS
AUX -
AUX -
MRALA YCNEUQERF WOL MRALA YCNEUQERF WOL
N I M Bd 5 8 LEVEL ERUSSERP DNUOS
AUX -
MRALA YCNEUQERF WOL
: TNERRUC MRALA AUX, V24VDC
4 2 DET(-)
ALUGER : TNERRUC MRALA AUX, V24VDC
4 2 DET(-)
ALUGER : TNERRUC MRALA AUX, V24VDC
4 2 DET(-)
ALUGER
XAM RWF Am3 0 2 AUX, 24VFWR
XAM CD Am(-)0 4 1 XAM RWF Am3 0 2 AUX, 24VFWR (-)0 4 1
AUX +
AUX +
AUX +
XAM CD Am XAM RWF Am3 0 2 AUX, 24VFWR
XAM CD Am(-)0 4 1
AUX + FOR INSTALLATION OR MAINTENANCE AUX + FOR INSTALLATION OR MAINTENANCE AUX + FOR INSTALLATION OR MAINTENANCE
LOOP OUT AUX 24VDC (+)
AUX 24VFWR (+)
SEE DWG # HA-06-361 REV 03/18
USE ONLY WITH AIE-EA, ALG-V, ALK-V,
AUX 24VDC (+)
AUX 24VFWR (+)
SEE DWG # HA-06-361 REV 03/18
USE ONLY WITH AIE-EA, ALG-V, ALK-V,
AUX 24VDC (+)
SEE DWG # HA-06-361 REV 03/18
AUX 24VFWR (+) USE ONLY WITH AIE-EA, ALG-V, ALK-V,
ALK-V2, ALN-V, ATG-EA, ATJ-EA,
SC
SC
SC
ALK-V2, ALN-V, ATG-EA, ATJ-EA, ALK-V2, ALN-V, ATG-EA, ATJ-EA,
DCP S- ACA-V, ACC-V, ACD-V SENSORS DCP S- ACA-V, ACC-V, ACD-V SENSORS DCP S- ACA-V, ACC-V, ACD-V SENSORS
For service, return to: For service, return to: For service, return to:
Hochiki America Corporation Hochiki America Corporation Hochiki America Corporation
S
7051 Village Drive, Suite 100 7051 Village Drive, Suite 100 7051 Village Drive, Suite 100
DCP S+ Buena Park, CA 90621-2268 DCP S+ Buena Park, CA 90621-2268 DCP S+ Buena Park, CA 90621-2268
LOOP IN
AUX 24VDC
NOTE: Class X wire configuration requires the installation of short circuit isolation.
DASHED LINES DRAWN FOR CLASS A/X. DO NOT CONNECT FOR CLASS B WIRING.
MOUNTING SCREWS
(NOT SUPPLIED)
8-32, 3.5" Suggested
3"
MIN. 1-1/2" OPTIONAL TRIM RING
EXTENSION RING P/N: 1400-04540
(NOT SUPPLIED)
MOUNTING SCREWS
(NOT SUPPLIED)
FIGURE 1
DWG. # HA-06-361
MOUNTING EXPLODED VIEW (PG 2 of 2, 03/18)
PART# 1700-12120