Professional Documents
Culture Documents
Lifting Lug Metso
Lifting Lug Metso
The information on this sheet is based on Crosby Shackles both Forged and Alloy, Confirm with Vendor Type being USED!
Lifting lug Info
TOTAL LIFTED LOAD 22.047 kips Considered a LIGHT Package!
PLATE THICK t= 1.000 inches tmax ≤ 2.6 inches AND, tmin ≥ 1.95 inches
HOLE DIAM DIA= 2.362 inches For Shackle Pin sized, Min Dia req'd = 3.125 inches
PLATE WIDTH b= 5.91 inches bmax ≤ 17.75 inches AND, bmin ≥ 5.905 inches
by User by SWL
A 2.38 2.38
B 3.62 3.62
C 1.62 1.62
D 1.63 1.63
E 5.75 5.75
F 1.39 1.39
G 6.88 6.88
H 7.75 7.75
J 10 10
K 3.88 3.88
L 1.54 1.54
Weight
20.8 20.8
(lbs)
reference EM/039 Rev 3 1991
Dynamic Amplification Factors (Fh) for LIGHT Packages
Offshore lift Upper Offshore LIFT Offshore lift lower
OnShore Lift
Bound Recommended Bound
4400
2200
(K
IP
S)
1100
(2200kips)
(1100kips)
220
110
(165kips)
22
reference EM/039 Rev 3 1991
DAF for module weights between the values given above, should be calculated by a
linear interpolation.
reference EM/039 Rev 3 1991
Angle 65º for single and dual lifts for differing L/B ratio's
reference EM/039 Rev 3 1991
Angle 70º for single and dual lifts for differing L/B ratio's
reference EM/039 Rev 3 1991
Angle 75º for single and dual lifts for differing L/B ratio's
reference EM/039 Rev 3 1991
Angle 80º for single and dual lifts for differing L/B ratio's
reference EM/039 Rev 3 1991
Lift Criteria Comparison- Single Crane Lifts, HEAVY LIFTS
JIP, Joint Industry Project
HEEREMA DnV MICOPERI SHELL OXY BP AMOCO CHEVERON NOBLE
BRV JIP (1991)
(1983) (1985) (1985) SOLE PIPER BRUCE CATS ALBA DENTON
PIT (1990) (1990) (1990) (1990) (1990)
A(5) B(3)
(1988)
Range of Module
>5,500 >,2200 >5,500 >5,500 >5,500 >5,500 >5,500 13,200/5,500 13,200/5,500
Weights (kips)
Weight Factor
A 1.15 1.10 1.15 1.15(1) 1.15(1) 1.15(1) 1.15 1.15 1.13 1.175 1.175
(PRE-AFC)(4)
D.A.F
B 1.10 1.10 1.10 1.10 1.10 1.10 1.10 1.10 1.10 1.15/1.20 1.15/1.20
(Slings)
Skew loads
C 1.50 1.25 1.50 1.50 1.50 1.50 1.25 1.50 1.25 1.50 1.25
Factor
C.G Shift
D 1.00 1.00 1.00 1.05(2) 1.00 1.00 1.05 1.05 1.05(2) 1.05 1.02(8)
Factor
Tilt
E 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.05 1.03(7)
Factor
F AxBxCxD 1.90 1.51 1.90 1.99 1.90 1.90 1.66 1.99 1.62 2.23/2.33 1.77/1.85
NOTES: 1. Factor not quoted, but assumed for this comparison table.
2. Factor used, but not quoted and assumed for this comparison table.
3. Skew load factor can be reduced to 1.25 min by use of curves, depending upon measured sling lengths.
4. Factor based on average of factors for structural and equipment.
5. Sling DAF varies linearly with the module weight, from 1.2 at 5,500kips to 1.15 at 13,200kips.
7. Tilt factor assumed if tilt is 1% or less.
8. Factor can be reduced to 1.02 after weighing.
Range of Module
>17,600 >2,200 >5,500 >5,500 >5,500 >5,500 22,000/13,200
Weights (kips)
Weight Factor
A 1.15 1.15 1.15 1.25 1.15 1.125 1.175
(PRE-AFC)(1)
D.A.F
B 1.10 1.10 1.10 1.10 1.10 1.10 1.10/1.15
(Slings)
C.G Shift
C 1.08 10.50 1.05 1.05 1.05 1.03 1.05
Factor
Tilt
D 1.08 1.03 1.03 1.03 1.03 1.03 1.03(4)
Factor
Yaw
E 1.00 1.05 1.05 1.00 1.05 1.05 1.00(6)
Factor
Torsion
F 1.00 1.00 1.10 1.00 1.00 1.00 1.00
Factor
Skew loads
G 1.10 1.10 1.00 1.10 1.00 1.00 1.03
Factor