Professional Documents
Culture Documents
A82V 9580 00E - MK P06 - NC P03 - Install
A82V 9580 00E - MK P06 - NC P03 - Install
INSTALLATION MANUAL
Applied Machines: C3850FS/C3850/C3350
COLOR MFP: 38 ppm/33 ppm
Product Code: A72R/A3GN/A4Y4
1. Accessory parts
< Mount kit MK-P06 >
No. Name Shape Q’ty After unpacking, be sure to get rid of the
packaging materials and keep them out
1. Mounting plate of the reach of children.
Putting the head in the plastic bag
1 involves danger of suffocation.
Note:
2. USB cable • This manual provides the illustrations of the
1 accessory parts and machine that may be
slightly different in shape from yours. In that
case, instead of the illustrations, use the
3. Wire saddle appearance of your machine to follow the
installation procedure. This does not cause any
1
significant change or problem with the proce-
dure.
4. Screw • If the mount kit MK-P06 and network interface
2 card NC-P03 are to be mounted at the same
time with the local interface kit EK-P01, mount
5. Installation
the local interface kit EK-P01 first.
manual
1 set
2. Installation procedures
(1) Turn OFF the power switch and unplug the
power cord from the power outlet.
(2) Open the packing carton of each option and take
< Network interface card NC-P03 > out the accessory parts.
(3) Remove the cord clamp if used to secure the
No. Name Shape Q’ty power cord of the main body. (One screw)
1. Network inter- (4) Unplug the power cord from the main body.
face card
1
2. Manual *
1 set
A82V-9580-00
E-1
(5) (7) Remove the rear cover. (Five screws)
<For C3850FS> Note:
Remove the rear left cover. (Two screws) Remove the screw A shown in the illustration only
if step (3) is not executed.
<For C3850/C3350>
Remove the rear left cover. (One screw) (8) Clear the stopper and remove the tray 1.
(One screw)
(6) Remove the filter from the back of the main body.
(9) Open the front door and remove the left cover.
(Two screws)
E-2
(10) <For C3850/C3350>
<For C3850FS> Remove the three screws fixing the exit tray.
a) Move the aligning plate of the finisher inside.
Note:
When moving the aligning plate, apply your finger
to the bottom plate of the aligning plate. For fear of
damage, do not hold onto the standing portion of
the aligning plate.
Connector
E-3
(14) Remove the front left cover. (17) Pass the connector of the USB cable of the net-
work interface card assy through the hole
shown in the illustration and fix the network
interface card assy to the main body. (Two sup-
plied screws)
Wire saddle
E-4
(20) To install the covers and other parts removed in 3. Setting up network interface card
steps (3) to (14), reverse the removal proce-
dure. (1) Plug the power cord into the power outlet and
turn ON the power switch.
Note:
(2) Display the Service Mode screen.
<Only for C3850FS>
(For details of how to display the Service Mode
• When reinstalling the exit tray that has been
screen, see the service manual.)
removed in step (10), fit the bosses on the right
and left ends of the exit tray into position, while (3) Touch “ .”
placing the rib on the right of the exit tray under (4) Touch “2nd network card settings.”
the control panel upper cover. (5) Touch “Installed.”
• There is no need to move the aligning plate of (6) Touch “OK.”
the finisher to the original position. (7) Touch “Close.”
(8) Turn OFF and ON the power switch.
Note:
When displayed the Service Mode screen, be sure
to turn off the power after exiting the Service Mode
screen and wait for 10 seconds or more before
turning on.
E-5