Professional Documents
Culture Documents
Bomba 426b
Bomba 426b
Page 1 of 25
Cerrar SIS
Pantalla anterior
Desarmado y Armado
416B, 426B, 428B,436B, AND 438B BACKHOE LOADERS MACHINE SYST
Número de medio -SENR5812-00 Fecha de publicación -01/06/1993 Fecha de actualización -12/10/2001
Implement Pump
SMCS - 5070-016; 5070-017; 5070-010; 5070-015
a. remove counterweight
1. Remove drain plug (1), and drain the oil from the hydraulic tank into a suitable container.
a. First, disconnect the fuel shut-off solenoid at the fuel injection pump.
b. Crank the engine until bolts (2) are in alignment with the access hole in the engine mounting
assembly. Loosen bolts (2) that hold drive shaft and hydraulic pump coupling.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 25/08/2022
426B BACKHOE LOADER 5YJ00001-02299 (MACHINE) POWERED BY 3054 E... Page 2 of 25
3. Disconnect hydraulic hoses (4) and (5) and lines (3) and (6).
5. Reverse the procedures in Steps 1 through 4 for the installation of the hydraulic pump.
End By:
a. install counterweight
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 25/08/2022
426B BACKHOE LOADER 5YJ00001-02299 (MACHINE) POWERED BY 3054 E... Page 3 of 25
NOTE: Do not move adjusting screw to maintain adjustment for later assembly.
NOTE: Do not move adjusting screw to maintain adjustment for later assembly.
NOTE: Do not move adjusting screw to maintain adjustment for later assembly.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 25/08/2022
426B BACKHOE LOADER 5YJ00001-02299 (MACHINE) POWERED BY 3054 E... Page 4 of 25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 25/08/2022
426B BACKHOE LOADER 5YJ00001-02299 (MACHINE) POWERED BY 3054 E... Page 5 of 25
37. Remove nine pistons (39) and plate (40) from cylinder block (37).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 25/08/2022
426B BACKHOE LOADER 5YJ00001-02299 (MACHINE) POWERED BY 3054 E... Page 6 of 25
The spring located within the cylinder block is under compression and
can cause bodily harm, if caution is not used, if or when the retaining
ring is removed.
40. Use a press and a 4B5273 1/2" Washer (43) to compress the spring, and remove snap ring (44)
with Tool (B).
42. Remove washer (44), spring (45) and washer (43) from cylinder block (37).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 25/08/2022
426B BACKHOE LOADER 5YJ00001-02299 (MACHINE) POWERED BY 3054 E... Page 7 of 25
NOTE: The following steps are for the assembly of the implement pump.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 25/08/2022
426B BACKHOE LOADER 5YJ00001-02299 (MACHINE) POWERED BY 3054 E... Page 8 of 25
53. Inspect and replace pin (52) if necessary and torque limiter adapter (51).
54. Remove and clean debris from in and behind the two orifices (53).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 25/08/2022
426B BACKHOE LOADER 5YJ00001-02299 (MACHINE) POWERED BY 3054 E... Page 9 of 25
56. Install plate (40) and nine pistons (39) into cylinder block (37).
58. Assemble shaft (54), swashplate (45) and cylinder block (37) on shaft (54).
60. Apply a small amount of grease to the backside of bearings (46) and install into pump housing.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 25/08/2022
426B BACKHOE LOADER 5YJ00001-02299 (MACHINE) POWERED BY 3054 ... Page 10 of 25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 25/08/2022
426B BACKHOE LOADER 5YJ00001-02299 (MACHINE) POWERED BY 3054 ... Page 11 of 25
67. Remove and clean debris out from behind orifice (55).
70. Preassemble the torque limiter as shown. Do not assemble spring (5) or plug (4) at this point.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 25/08/2022
426B BACKHOE LOADER 5YJ00001-02299 (MACHINE) POWERED BY 3054 ... Page 12 of 25
74. Apply a liberal amount of grease on post (59) and shoe (31).
77. Install torque limiter (2) without spring (5) or plug (4).
79. Install pump head (29) to pump body with pump in position as seen in photo C58933P1 Step
66 in this procedure.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 25/08/2022
426B BACKHOE LOADER 5YJ00001-02299 (MACHINE) POWERED BY 3054 ... Page 13 of 25
Start By:
1. Remove bolts (2) that hold the compensator to the valve block. Remove compensator (1).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 25/08/2022
426B BACKHOE LOADER 5YJ00001-02299 (MACHINE) POWERED BY 3054 ... Page 14 of 25
3. Remove adjustment nut (4) and the plug. Remove plug (5).
4. Remove seat (7), spring (6) and spacer (8). Remove valve spool (9).
6. Remove seat (12), spring (13) and spacer (14). Remove valve spool (15).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 25/08/2022
426B BACKHOE LOADER 5YJ00001-02299 (MACHINE) POWERED BY 3054 ... Page 15 of 25
7. Remove bolts (17), and remove valve block (16) and the gasket.
8. Remove stem (18), stem (19), pin (20) and remove valve assembly (21) from the valve block.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 25/08/2022
426B BACKHOE LOADER 5YJ00001-02299 (MACHINE) POWERED BY 3054 ... Page 16 of 25
The spring located within the cylinder block is under compression and
can cause bodily harm, if caution is not used, if or when the retaining
ring is removed.
12. Carefully compress the spring, and remove the retaining ring with Tool (A).
13. Remove the spring washer, spring (27) and the spring washer from the cylinder block.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 25/08/2022
426B BACKHOE LOADER 5YJ00001-02299 (MACHINE) POWERED BY 3054 ... Page 17 of 25
16. Remove piston and shoe assembly (31) from the pump body.
17. Remove O-ring seal (32), bearing spacer (33) and bearing (34).
18. Remove shaft (35), swashplate (36) and the yoke and bumper assembly from the pump
housing.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 25/08/2022
426B BACKHOE LOADER 5YJ00001-02299 (MACHINE) POWERED BY 3054 ... Page 18 of 25
20. Remove bearing race (38) and inner lip seal (39).
1. Install the inner and outer seals in the pump housing with Tool (A).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 25/08/2022
426B BACKHOE LOADER 5YJ00001-02299 (MACHINE) POWERED BY 3054 ... Page 19 of 25
2. Lower the temperature of the bearing race, and install it in the pump housing.
5. Follow the procedures below to provide the proper preload on the bearings.
6. Lower the temperature of the bearing race, and install it in the pump housing. Install bearing (2)
and bearing spacer (3). Do not install the O-ring at this time.
7. Install cover (4), and tighten bolts (5) to a torque of 15 to 17 N·m (11 to 13 lb ft)
8. Turn the pump housing over. Lower the temperature of the bearing race, and install it in the
pump housing. Install bearing (7) and bearing spacer (6). Do not install the O-ring at this time.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 25/08/2022
426B BACKHOE LOADER 5YJ00001-02299 (MACHINE) POWERED BY 3054 ... Page 20 of 25
9. Rotate the yoke assembly back and forth to seat the bearings.
10. Measure the distance between the spacer and housing with a depth micrometer as shown.
11. Install the proper shim (8) to have a 0.25 to 0.40 mm (0.010 to 0.016 in) axial pre-load. Install
bearing spacer (6), O-ring seal, cover and bolts. Tighten the bolts to a torque of 15 to 17 N·m (11
to 13 lb ft).
12. Turn the housing over again, and remove the other cover and bolts. Install the O-ring seal,
cover and bolts. Tighten the bolts to a torque of 15 to 17 N·m (11 to 13 lb ft).
NOTE: The yoke will be stiff but should be loose enough to be moved by hand. If the yoke can
not be moved by hand, the preload is too great. Repeat the preload adjustment until it is correct.
NOTICE
Put tape around the splines on shaft (9) to avoid damaging the shaft
seal when the shaft is installed.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 25/08/2022
426B BACKHOE LOADER 5YJ00001-02299 (MACHINE) POWERED BY 3054 ... Page 21 of 25
14. Install swashplate (10) making sure the hole in the swashplate is in alignment with pin (11).
15. Install spring washer (14), spring (12) and spring washer (15) in the cylinder block. Install
retaining ring (13) on top of spring washer (15).
17. Carefully compress the spring, and install the retainer ring with Tool (B).
18. Install piston and shoe assembly (16) in the cylinder block.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 25/08/2022
426B BACKHOE LOADER 5YJ00001-02299 (MACHINE) POWERED BY 3054 ... Page 22 of 25
19. Install the piston and cylinder block assembly in the pump housing.
20. Turn the cage shoe assembly so that key slot (17) will be in alignment when the key is
installed.
21. Remove the bolts and covers, and install key (18).
22. Install cover and bolts. Tighten the bolts to a torque of 15 to 17 N·m (11 to 13 lb ft).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 25/08/2022
426B BACKHOE LOADER 5YJ00001-02299 (MACHINE) POWERED BY 3054 ... Page 23 of 25
24. If the shaft bearing, shaft, valve block or housing was replaces, a bearing adjustment is
necessary. Use the following procedures.
25. Lower the temperature of the bearing race, and install it in the valve block with Tool (A).
27. Install the valve block on the housing, and hand tighten the bolts evenly. Measure the gap at
four positions around the housing, and take the average reading. Also measure the gasket
thickness. With this measurement, determine the spacer or spacers necessary to obtain 0.00 to
0.100 mm (0.00 to 0.0039 in) bearing end play. Remove the valve block, and install the correct
spacer or spacers.
28. Install stems (23) and (24) in the valve block. Tighten the stems to a torque of 75 to 85 N·m
(55 to 65 lb ft).
29. Install washer plate (25) on the valve block, making sure the slot in the plate is in alignment
with the pin in the valve block. Put clean grease on the plate to hold it in place.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 25/08/2022
426B BACKHOE LOADER 5YJ00001-02299 (MACHINE) POWERED BY 3054 ... Page 24 of 25
30. Install spring (28) and cylinder (27) on stem (24). Install cylinder (26) on stem (23).
31. Put clean grease on the cylinders to hold them in place for assembly.
32. Put valve block (29) in position, and install bolts (30) that hold it. Tighten the bolts to a torque
of 50 to 55 N·m (37 to 41 lb ft).
33. Install valve spool (33) and plug (35). Install spacer (32), spring (34) and seat (31).
36. Install spacer (41), spring (40), seat (39) and adjustment plug (38).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 25/08/2022
426B BACKHOE LOADER 5YJ00001-02299 (MACHINE) POWERED BY 3054 ... Page 25 of 25
38. Put compensator (44) in position on the valve block, and install bolts (45) that hold it. Tighten
the bolts to a torque of 31 to 37 N·m (23 to 27 lb ft)
End By:
Copyright 1993 - 2022 Caterpillar Inc. Thu Aug 25 07:35:54 EST 2022
Todos los derechos reservados.
Red privada para licenciados del SIS.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 25/08/2022