Professional Documents
Culture Documents
MasterSeal TC 244 PDF Industrial Processes Building Engineering 2
MasterSeal TC 244 PDF Industrial Processes Building Engineering 2
Copyright
Download now !
© © All Rights Reserved
Available Formats
PDF, TXT or read online from Scribd
Typical Properties*
Description
Mixing ratio Part A/ Part B 4 : 1 by volume.
MasterSeal® TC 244 is a solvented two component Tensile strength 10 N/mm²
Facebook
polyurethane coating which when applied to
MASTERTOP epoxy primers or coating systems
Twitter Bond strength
Permeability
3 MPa
0
produces a permanently elastic, wear, abrasion and Touch Dry 4 hours at 25ºC
UV resistant surface. It is available in gloss finish. It Over-coating Time 16 - 24 hrs at 25ºC
can be applied as coating on walls. Pot life 4 hours at 25ºC
Primary Uses
%
With its excellent elasticity, abrasion and UV
resistance MasterSeal® TC 244 is suitable for non
Chemical resistance
IsColours
this content inappropriate? Report
surfacethis Document
Suitable preparation includes light grit blasting,
grinding or captive shot blasting. Repair
surface defects using MasterBrace ADH 2200 or other
Clear or pigmented to most RAL or BS Colours. suitable repair compound from the BASF
MasterEmaco or MasterBrace.
Priming
Packaging
Stir both components of MasterTop® P 444 Primer
before combining.
MasterSeal® TC 244 is supplied in 20 Ltrs. Add part B into Part A and mix with a slow speed drill
(200-300 rpm) and paddle for 3 minutes.
MasterSeal® P 244 Primer is supplied in 4 liter packs.
For a non-slip finish, broadcast approx. 1kg/m2 of the
Coverage selected MASTERTOP SRA.
MasterSeal® TC 244 is applied as two coats at 6m2/ Note: If a smooth surface finish is required, omit the
litre per coat. MASTERTOP SRA.
Master !"#$® T% '((
Upload to Download
contact your local BASF representative.
from extremes of temperatures. In tropical climates BASF reserves the right to have the true cause of any
Ap
the plproduct
ic ati on must be stored in an air conditioned
Stir both components of MasterSeal® TC 244 before difficulty determined by accepted test methods.
environment.
combining.
Part Bmay
to Part A in
!"#$
Failure to comply with the recommended storage
Add and mix withdeterioration
a slow speed
% '(( Quality and care
All BASF Products are manufactured under a
conditions result premature of drill
the management system independently certified to
(200 - 300
product or rpm) and suitable
packaging. paddle storage
For specific attachment for
advice conform to the requirements of the quality,
OR
five minutes.
consult BASF's Technical Department. environmental and occupational health and safety
standards of ISO 9001 and BASF ESHQ
Apply MasterSeal® TC 244 by roller or recommendations.
Master T
airless spray to the primed tack free surface. Apply at
the rate of 6m2/ liter per coat in two coats allowing 16
*
Properties listed are only for guidance and are not a guarantee of
performance
Storage
download full documents.
Store under cover out of direct sunlight and protect
from extremes of temperatures. In tropical climates
the product must be stored in an air conditioned
environment.
Field service where provided does not constitute supervisory responsibility. Suggestions made by
NOTE BASF either orally or in writing may be followed, modified or rejected by the owner, engineer or contractor since
they, and not BASF, are responsible for carrying out procedures appropriate to a specific application.
Share this document Field service where provided does not constitute supervisory responsibility. Suggestions made by
BASF either orally or in writing may be followed, modified or rejected by the owner, engineer or contractor since
they,
Saudi BASF for Buil ding and not
Materials
P.O. Box 1884, Al Khobar, KSA Co.BASF,
Ltd. are responsible for carrying out procedures appropriate to a specific application.
" # $ % &
Dupont TDS_373P27680
Primer
mpedraza-1
804516_EN
Kisgyörgy Zoltán
Magazines Podcasts
Sheet Music
14_chapter 5.pdf
Varshini Varshini
Industrial Processes
Building Engineering
Industries Chemistry
Touchwood Woodorite
Primer
MuthuKumar
Floor Paint
chayanun
CC4624
Ibhar Santos Mumenthey
G 652D.pdf
Jorge Matii Zrd
ISO-17020 Inspection
Accreditation Standard by
Independant Bodies.pdf
rizzo8
Show more
About Support
Press Accessibility
Contact us Publishers
Invite friends
Social
GiPs
Twitter
Legal
Facebook
Terms Pinterest
Privacy
Copyright
Cookie Preferences
Language: English