Professional Documents
Culture Documents
Assignment 1
Assignment 1
Correct Answer: c
Detailed Solution: Slide no. 17, Lecture no. 01
______________________________________________________________________________
QUESTION 2:
What does ISST stand for?
1
a. Indian Standard Steel Strip Section
b. Indian Standard Steel Sheet Section
c. Indian Standard Steel Strap Section
d. None of the above
Correct Answer: a
Detailed Solution: Slide no. 18, Lecture no. 01
NPTEL Online Certification Courses
Indian Institute of Technology Kharagpur
QUESTION 3:
Stainless steel is manufactured by adding foreign materials like
1
a. zinc, nickel, and copper
b. nickel and zinc
c. zinc and chromium
d. nickel and chromium
Correct Answer: d
Detailed Solution: Slide no. 5, Lecture no. 02
QUESTION 4:
Due to uneven heating and cooling during manufacturing process of structural steel, which stress
is generated?
1
a. Flow stress
b. Residual stress
c. Fatigue stress
d. Structural stress
Correct Answer: b
Detailed Solution: Slide no. 11, Lecture no. 02
NPTEL Online Certification Courses
Indian Institute of Technology Kharagpur
QUESTION 5:
Increase in the carbon content of steel will result in:
1
a. Increase in its strength
b. Decrease in its ductility
c. Increase in both strength and ductility
d. Both (a) and (b) options are correct
Correct Answer: d
Detailed Solution: Slide no. 5, Lecture no. 02
QUESTION 6:
What should be the maximum permissible lateral deflection for the case of inter story drift in an
ordinary building having story height of 3 m under the action of wind load?
2
a. 12.00 mm
b. 10.00 mm
c. 9.23 mm
d. 8.57 mm
Correct Answer: b
Detailed Solution: Slide no. 14, Lecture no. 03
Floor height = 3 m
𝑠𝑡𝑜𝑟𝑦 ℎ𝑒𝑖𝑔ℎ𝑡 3000
Max. permissible lateral deflection for the case of inter story drift = = = 𝟏𝟎 𝐦𝐦
300 300
NPTEL Online Certification Courses
Indian Institute of Technology Kharagpur
QUESTION 7:
In case of staggered pitch, pitch may be increased by:
1
a. 50%
b. 30%
c. 20%
d. 10%
Correct Answer: a
Detailed Solution: Clause 10.2.3.4 of IS 800:2007
NPTEL Online Certification Courses
Indian Institute of Technology Kharagpur
QUESTION 8:
Consider a typical stress-strain curve of a structural steel specimen shown in figure. What is the
name of the zone specified as ‘DE’?
U
fu
C F
fy
B D E
f A
Stress (MPa)
ε Strain (%)
2
a. Strain hardening
b. Strain softening
c. Yield plateau
d. Elastic zone
Correct Answer: c
Detailed Solution: Slide no. 13, Lecture no. 02
QUESTION 9:
The centre-to-centre distance of adjacent rivets or bolt holes measured in the direction of stress is
called:
1
a. Pitch
b. Nominal diameter
c. Edge distance
d. Gauge distance
NPTEL Online Certification Courses
Indian Institute of Technology Kharagpur
Correct Answer: a
Detailed Solution: Slide no. 16, Lecture no. 04
QUESTION 10:
According to IS 800:2007, what should be partial safety factor for material whose resistance is
governed by yielding?
1
a. 1.00
b. 1.10
c. 1.25
d. 1.50
Correct Answer: b
Detailed Solution: Slide no. 12, Lecture no. 03
QUESTION 11:
According to IS 800:2007, what is the appropriate load combination for DL (Dead Load) and ER
(Erection Load) in case of limit state of strength? (LL = Live Load)
1
a. 1.0 DL + 1.0 ER
b. 1.2 DL + 1.2 (0.9) LL
c. 1.2 (0.9) DL + 1.2 LL
d. 1.5 DL + 1.5 ER
Correct Answer: c
QUESTION 12:
According to IS 800:2007, what should be the diameter of bolt hole if diameter of bolt is 22 mm?
a. 25 mm
b. 24 mm
c. 23 mm
d. 22 mm
Correct Answer: b
Detailed Solution:
QUESTION 13:
Riveted connection has following advantages:
Correct Answer: a
QUESTION 14:
Calculate the nominal diameter of rivet if its gross diameter is 28 mm.
a. 28.0 mm
b. 27.0 mm
c. 26.5 mm
d. 26.0 mm
Correct Answer: d
QUESTION 15:
Name the connection shown in the figure.
Correct Answer: c
NPTEL Online Certification Courses
Indian Institute of Technology Kharagpur
QUESTION 16:
The reduction in area due to bolt holes can be minimized by:
1
a. arranging bolts in zig-zag form
b. arranging bolts in chain form
c. arranging bolts in linear form
d. None of the above
Correct Answer: a
************END***********