Download as doc, pdf, or txt
Download as doc, pdf, or txt
You are on page 1of 8

To Design the First order low pass filter at a high cut-off frequency (FH) of 1 KHZ

with the pass band gain (AF) of 3 by using Op-Amp and also plot the frequency response
curve of LPF.

To Design the First order high pass filter at a low cut-off frequency (FL) of 2 KHZ with
the pass band gain (AF) of 4 by using Op-Amp and also plot the frequency response
curve of HPF.

To Design a 1.5KHZ active Notch filter by using Op-Amp.

To Design a wide band pass filter with FL=500 HZ and FH=5 KHZ with the pass band
gain of (AF) of 4 by using Op-Amp and also calculate the value of figure of merit(Q) and
plot the frequency response curve of Band pass filter.

To Design the Instrumentation amplifier with the over all gain (Go) of 3 by using Op-
Amp.

To Design an Integrator by using Op-Amp to integrate an input signal that varies in


frequency from 1 KHZ to about 10 KHZ and also plot the integrator response curve.

To Design a Differentiator by using Op-Amp to differentiate an input signal that varies in


frequency from 1 KHZ to about 20 KHZ and also plot the differentiator response curve.

To Design the Inverting and Non-Inverting amplifier by using Op-Amp with the gain of
4, and apply both AC and DC to it and tabulate the Gain and also plot the frequency
response curve of AC.

To Design the First order low pass filter at a high cut-off frequency (FH) of 3 KHZ
with the pass band gain (AF) of 3 by using Op-Amp and also plot the frequency response
curve of LPF.

To Design the First order high pass filter at a low cut-off frequency (FL) of 5 KHZ with
the pass band gain (AF) of 4 by using Op-Amp and also plot the frequency response
curve of HPF.

To Design a 2KHZ active Notch filter by using Op-Amp.

To Design a 4 KHZ active Notch filter by using Op-Amp.

To Design the Inverting and Non-Inverting amplifier by using Op-Amp with the gain of
3, and apply both AC and DC to it, and tabulate the Gain for various input signals and
also plot the frequency response curve of AC.

To Design the First order low pass filter at a high cut-off frequency (FH) of 3 KHZ
with the pass band gain (AF) of 3 by using Op-Amp and also plot the frequency response
curve of LPF.
To Design the First order high pass filter at a low cut-off frequency (FL) of 5 KHZ with
the pass band gain (AF) of 4 by using Op-Amp and also plot the frequency response
curve of HPF.

To Design the differential amplifier with the gain of 3 by using Op-Amp.

To Design a wide band pass filter with FL=300 HZ and FH=3 KHZ with the pass band
gain of (AF) of 4 by using Op-Amp and also calculate the value of figure of merit(Q) and
plot the frequency response curve of Band pass filter.

To Design a wide band reject filter with FL=5 KHZ and FH=500 HZ and plot the
frequency response curve of Band reject filter.

To Design a wide band reject filter with FL=7.5 KHZ and FH=750 HZ and plot the
frequency response curve of Band reject filter.

a. To Design the 3 input inverting summing amplifier with the gain of 3 by using Op-
Amp.
b. To Design the differential amplifier with the gain of 3 by using Op-Amp.

To Design and set up the circuit to solve the following equation,


Y=2/3(A+B+C)

To Design and set up the circuit to solve the following equation,


Y=4/3(A+B+C)
To generate the following wave form within the frequency range of 300 HZ-3 KHZ
(don’t use oscillator Ckt),

v
t

To generate the Triangle-wave form within the frequency range of


1.5 KHZ-15 KHZ.

a. To Design the 3 input non-inverting summing amplifier with unity gain by using Op-
Amp.
b. To Design the differential amplifier with the gain of 3 by using Op-Amp.
To generate the following wave form within the frequency range of
300 HZ-6 KHZ (don’t use oscillator Ckt),
V

To generate the following wave form within the frequency range of 500 HZ-5 KHZ
(don’t use oscillator Ckt),

v
t

To generate the following wave form within the frequency range of


500 HZ-10 KHZ (don’t use oscillator Ckt),

To generate the Spike-wave form within the frequency range of


500 HZ-10 KHZ.

To generate the Spike-wave form within the frequency range of


1.5 KHZ-30 KHZ.

To Design the phase shift oscillator of Fo =500 HZ by using Op-Amp.

To Design the wien bridge oscillator of Fo =1.5 KHZ by using Op-Amp.


To Design the triangular wave generator of Fo =2 KHZ with Vo (PP) =7V by using Op-
Amp.

To Design the Astable multivibrator with free running frequency


Fo=2 KHZ by using Timer(555), also determine the positive pulse width(tc) and
negative pulse width(td) in 75 % duty cycle and also plot the input and output waveform.

To Design the monostable multivibrator with tp=0.5ms by using Timer (555) and also
plot the input and output wave form

To Design the square wave generator with free running frequency


Fo=5 KHZ using Op-Amp, also determine the positive pulse width(tc) and negative pulse
width(td) in 35 % duty cycle and also plot the input and output waveform.

To Design and setup the circuit to generate 500 HZ sine-wave form and convert it into
square waveform.

To Design and setup the circuit to generate 2 KHZ sine-wave form and convert it into
square waveform.

To Design the phase shift oscillator of Fo =200 HZ by using Op-Amp.

To Design the wien bridge oscillator of Fo =2.5 KHZ by using Op-Amp.

To Design the triangular wave generator of Fo =2 KHZ with Vo (PP) =7V by using Op-
Amp.

To Design the monostable multivibrator with tp=0.5ms by using Op-Amp and also plot
the input and output wave form

To Design the monostable multivibrator with tp=0.75ms by using Op-Amp ) and also
plot the input and output wave form

To Design the Astable multivibrator with free running frequency


Fo=2 KHZ by using Timer(555), also determine the positive pulse width(tc) and
negative pulse width(td) in 75 % duty cycle and also plot the input and output waveform.

To Design the monostable multivibrator with tp=0.5ms by using Timer (555) and also
plot the input and output wave form

To Design the square wave generator with free running frequency


Fo=5 KHZ using Op-Amp, also determine the positive pulse width(tc) and negative pulse
width(td) in 35 % duty cycle and also plot the input and output waveform.
To Design and setup the circuit to generate 500 HZ sine-wave form and convert it into
square waveform.

To Design and setup the circuit to generate 2 KHZ sine-wave form and convert it into
square waveform.

To Design and set up the Binary Weighted DAC circuit using OP-Amp.

To Design and set up the Binary R-2R Ladder DAC circuit using OP-Amp.

To Design and set up the Binary Weighted DAC circuit using OP-Amp.

To Design and set up the Binary R-2R Ladder DAC circuit using OP-Amp.

To Design and setup the circuit for the following plot,


15 V

-1.75 V 1.75 V
-15 V

To Design and setup the circuit for the following plot,

12 V

3V

-12 V
To Design and setup the circuit for the following plot,

9V

-2.5 V

-9 V

To Design and setup the circuit for the following plot,

12 V
.
-3 V 1.5 V

To Design and setup the circuit


-12 V for the following plot,

12 V

-1.25 V 2.75 V

-12 V

To Design and setup the circuit for the following plot,

12 V

-2.5 V 3.5 V

-12 V
To Design and setup the circuit for the following plot,

12 V

-3.5 V 1.75 V

-12 V

To Design the Low-Voltage Regulator with output voltage (Vo) of 3V and output current
(Io) 0f 1 mA, using variable voltage regulator LM 723, and also plot the line regulation.

To Design the High-Voltage Regulator with output voltage (Vo) of 15V and output
current (Io) 0f 1 mA, using variable voltage regulator LM 723, and also plot the line
regulation.

To Design the Low-Voltage Regulator with output voltage (Vo) of 4.3V and output
current (Io) 0f 1 mA, using variable voltage regulator LM 723, and also plot the line
regulation.

To Design the High-Voltage Regulator with output voltage (Vo) of 11.5V and output
current (Io) 0f 1 mA, using variable voltage regulator LM 723, and also plot the line
regulation.

To Design and set up the Pulse width modulator and demodulator circuit.

To Design and set up the Pulse width modulator and demodulator circuit.

To Design and set up the Pulse width modulator and demodulator circuit.

To Design and set up the PPM modulator.

To Design and set up the PPM modulator.

To Design and set up the PPM modulator.

To Design and set up the PAM modulator and demodulator circuit.

To Design and set up the PAM modulator and demodulator circuit.

To Design and set up the PAM modulator and demodulator circuit.


To design and set up the circuit to generate the following waveform,

0.5 ms 1 ms

To design and set up the circuit to generate the following waveform,

1 ms 2 ms
To design and set up the Half wave and Full wave Rectifier circuit using OP-Amp.

To design and set up the Half wave and Full wave Rectifier circuit using OP-Amp.

To design and set up the Half wave and Full wave Rectifier circuit using OP-Amp.

You might also like