Professional Documents
Culture Documents
SANS 1083-2017 - Aggregates From Natural Sources - Aggregates For Concrete
SANS 1083-2017 - Aggregates From Natural Sources - Aggregates For Concrete
ISBN 978-626-32
2362-2
SAN
NS 10
083:20
017
Edittion 2.5
SO
OUTH AFRIC
A CAN N
NATIO
ONAL
L STAN
NDAR
RD
Agg
gregattes fro
om nattural source
s es —
Agg
gregattes forr conc
crete
W
WARNING G
Th
his docum
ment refere
ences othher
documeents norm
matively.
SANS 1083:2017
Edition 2.5
Table of changes
Change No. Date Scope
Amdt 1 2002 Has been amended to correct a reference in the note to clause 4
and to update referenced standards.
Amdt 2 2006 Amended to change the designation of SABS standards to SANS
standards, to update the layout of definitions and to update the
referenced standards.
Amdt 3 2013 Amended to modify the introduction, update referenced
standards, to modify the definitions of "aggregate", "coarse
aggregate" and "fine aggregate", change the sieve grading sizes
and modify the requirements for coarse aggregate for use in
concrete.
Amdt 4 2014 Amended to update the grading of sieve sizes and referenced
standards.
Amdt 5 2017 Amended to correct the table on coarse aggregate for concrete,
and to add notes on quality verification and on tests and
guidance.
Foreword
This South African standard was approved by National Committee SABS/TC 081/SC 01,
Construction materials, products and test methods – Cement, lime and concrete, in accordance with
procedures of the SABS Standards Division, in compliance with annex 3 of the
WTO/TBT agreement.
A vertical line in the margin shows where the text has been technically modified by amendment
No. 5.
This document is referenced in the Firearms Control Act, 2000 (Act No. 60 of 2000).
Annex A forms an integral part of this document. Annexes B and C are for information only.
Compliance with this document cannot confer immunity from legal obligations.
Introduction
This standard contains requirements for aggregates derived from natural sources that yield material
of suitable characteristics and which, after normal processing (if necessary), can be safely used for
most concrete work. However, it does not cover requirements for all the properties of an aggregate.
Some of these properties could be important and, if not established to be satisfactory, could result
in the production of concrete of inferior quality, especially with regard to long-term performance.
Amdt 3
Authoritative technical literature should be consulted for guidance on the further investigation of an
aggregate to verify its suitability for use in concrete for any particular application. Such further
investigation could indicate that an aggregate that does not comply with the requirements of this
standard might nevertheless be suitable for use in any type of concrete or in concrete for specific
uses only. It is emphasized, however, that an aggregate that has been found satisfactory either
through past performance or by other means, but that does not comply with the requirements of this
standard, cannot be claimed to comply with it.
Aggregates that do not comply with the requirements of this standard should only be used after all
the consequences have been considered, and provided that the user possesses the necessary
expertise in the use of such materials.
© SABS
Licensed exclusively to Chavrone Oelofse.
Copying and network storage prohibited.
SANS 1083:2017
Edition 2.5
Contents
Page
Foreword
Introduction
1 Scope ..................................................................................................................................... 3
3 Definitions .............................................................................................................................. 4
4 Requirements ......................................................................................................................... 4
5 Documentation ....................................................................................................................... 10
Bibliography .............................................................................................................................. 16
© SABS 1
Licensed exclusively to Chavrone Oelofse.
Copying and network storage prohibited.
SANS 1083:2017
Edition 2.5
2 © SABS
Licensed exclusively to Chavrone Oelofse.
Copying and network storage prohibited.
SANS 1083:2017
Edition 2.5
1 Scope
This standard specifies requirements for fine and coarse aggregates from natural sources for use in
concrete.
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of
this standard. All standards are subject to revision and, since any reference to a standard is deemed to
be a reference to the latest edition of that standard, parties to agreements based on this standard are
encouraged to take steps to ensure the use of the most recent editions of the standards indicated below.
Information on currently valid national and international standards can be obtained from the
SABS Standards Division.
SANS 3001-AG1:2014, Civil engineering test methods – Part AG1: Particle size analysis of
aggregates by sieving. Amdt 3; amdt 4
SANS 3001-AG10, Civil engineering test methods – Part AG10: ACV (aggregate crushing value)
and 10 % FACT (fines aggregate crushing test) values of coarse aggregates. Amdt 3
SANS 3310-1/ISO 3310-1, Test sieves – Technical requirements and testing – Part 1: Test sieves
of metal wire cloth. Amdt 1
SANS 3310-2/ISO 3310-2, Test sieves – Technical requirements and testing – Part 2: Test sieves
of perforated metal plate. Amdt 1
SANS 6243, Deleterious clay content of the fines in aggregate (methylene blue adsorption indicator
test).
SANS 6244, Particles of diameter not exceeding 20 µm and not exceeding 5 µm and smaller,
respectively, in fine aggregate (pipette method).
© SABS 3
Licensed exclusively to Chavrone Oelofse.
Copying and network storage prohibited.
SANS 1083:2017
Edition 2.5
3 Definitions
For the purposes of this standard, the following definitions apply:
3.1
aggregate
material formed by the natural disintegration of rock, or produced by the mechanical crushing or
milling of rock Amdt 3
3.2
coarse aggregate
aggregate of particle size such (to the extent specified in the standard) that it is retained on a sieve
that has square apertures of nominal size either 4 750 µm or 5 mm as referenced in 4.1
SANS 3001-AG1:2014 Amdt 3; amdt 4
3.3
fine aggregate
aggregate of particle size such (to the extent specified in the standard) that at least 90 % of its mass
passes a sieve that has a square apertures of nominal size of 4 750 µm or 5 mm as referenced
in 4.1 of SANS 3001-AG1:2014 and is retained on a sieve that has square apertures of nominal size
75 µm Amdt 3; amdt 4
3.4
type (of aggregate)
denotes the intended use of the aggregate
4 Requirements
NOTE This clause contains the basic requirements for aggregates that are known not to contain deleterious
contaminants other than those for which limits have been laid down in this standard and that can be complied
with by normal processing, including washing with water. Aggregates derived from sources that yield material
of unknown or suspect mineralogical and performance characteristics need to be subjected to further testing.
Consult annex C for guidance on the interpretation of results so obtained. (See also the introduction to this
standard.) Amdt 1
Fine aggregate for use in concrete shall be of one of the classes given in 4.1, as required (see
annex A). Fine aggregate shall, subject to the requirements of 4.2.2 to 4.2.4, comply with the
requirements given in table 1, appropriate to the class.
4 © SABS
Licensed exclusively to Chavrone Oelofse.
Copying and network storage prohibited.
SANS 1083:2017
Edition 2.5
4.2.2 Grading
If a specific grading for a specific purpose is required, the grading limits for the fine aggregate in
respect of sieves of aperture sizes 4750 µm, 2 360 µm, 1 180 µm, 600 µm, 300 µm or 5 mm, 2 mm,
1 mm, 600 µm and 300 µm as referenced in 4.1 of SANS 3001-AG1:2014 shall be as required (see
annex A), subject to adherence to the requirement for fineness modulus (see 4.2.4). Amdt 3; amdt 4
The limit of dust content given in column 2 of table 1, in respect of a mixture (blend) of fine
aggregate (see 4.1(c)) is applicable to any mixture of which the proportional representation of the
classes in the mixture is not known. If these proportions are known, the relevant requirement given
in columns 2 and 3 of table 1 may be increased (see 4.2.3.2), using the values given in columns 2
and 3 of table 1, as follows:
xa yb
D
100
where
x is the percentage representation of material derived from the natural disintegration of rock;
The limits for dust content given in column 2 and 3 of table 1 may be increased to 10 % and 20 %
respectively, provided that
a) the fine aggregate complies with the requirement for the methylene blue adsorption value (see
table 1), or
b) the fine aggregate complies with the requirement for clay content (see table 1).
NOTE The following sequential procedure for the evaluation of a sample of fine aggregate in respect of dust
and clay content is recommended:
a) Determine the dust content and, if the value does not exceed the limits given in column 2 or 3 of table 1, as
appropriate, accept the sample.
b) If the dust content exceeds the limits given in column 2 or 3 of table 1, as appropriate, but does not exceed
the increased values provided for in 4.2.3, conduct the methylene blue adsorption test. If the sample
complies with the requirement given in table 1 for this property, accept the sample.
c) If the sample does not comply with the requirement for the methylene blue adsorption test, determine the
clay content. If the clay content does not exceed the limit given in table 1, accept the sample.
d) If the clay content exceeds the limit given in table 1, reject the sample.
© SABS 5
Licensed exclusively to Chavrone Oelofse.
Copying and network storage prohibited.
SANS 1083:2017
Edition 2.5
The fineness modulus of a fine aggregate shall not deviate by more than 0,2 from the value as
stated in respect of a delivery of fine aggregate during a contract (see 5(b)). When relevant, the
range within which the fineness modulus falls shall be as required (see annex A). However, the
fineness modulus shall in all cases fall within the limits given in table 1.
4.3.1 Coarse aggregate for use in concrete shall comply with the requirements given in table 2,
appropriate to the type and nominal size required (see annex A).
4.3.2 If the grading of any nominal size of aggregate as given in table 2 (except for aggregate of
nominal size 6,7 mm or 7,1 mm as referenced in 4.1 of SANS 3001-AG1:2014 is required to be
uniform in respect of any delivery during a contract, the supplier shall state the coefficient of
uniformity (Ua) that can be maintained for the duration of such contract from a specific source
(see 5(c)). The stated coefficient of uniformity shall be subject to a deviation as agreed upon (see
annex A). Amdt 3; amdt 4
D60
Ua
D30
where
D60 is the sieve aperture size (hypothetical) through which 60 % of the mass of the material
passes;
D30 is the sieve aperture size (hypothetical) through which 30 % of the mass of the material
passes.
NOTE The sieve aperture size of which 60 % and 30 % of the mass of the material passes can be determined
with the aid of a grading curve of the aggregate tested (using normal graph paper with enlarged scale), or can
be calculated from the results.
6 © SABS
Licensed exclusively to Chavrone Oelofse.
Copying and network storage prohibited.
1 2 3 4
Class
Fine aggregate derived from the natural disintegration Fine aggregate derived
Property of rock and any mixture (blend) of this class and fine from the mechanical Test method
aggregate derived from the mechanical crushing crushing or milling subclause
or milling of rock of rock
1
Grading, mass percentage that passes sieves ) that have 6.2
square apertures of nominal size
5 000 µm 92 – 100
4 750 µm 90 – 100
150 µm 5 – 25
1)
Dust content, material that passing a 75 µm sieve , mass 6.3
2) 2)
percentage, max. 5 10
© SABS
3)
Methylene blue adsorption value , max. 0,7 6.4
4)
Clay content , material of particle size smaller than 5 µm, 2,0 6.5
mass percentage, max.
Fineness modulus 1,2 – 3,5 6.6
5) −
Chloride content , expressed as Cl , mass percentage, Fine aggregate for 6.7
max.
concrete for prestressing : 0,01
normal reinforced concrete : 0,03
non-reinforced concrete : 0,03
Organic impurities The colour of the liquid above the fine aggregate shall not 6.8
be darker than the colour of the reference solution, except
that this requirement shall not be applicable if the fine –
aggregate complies with the requirement for soluble
deleterious impurities.
SANS 1083:2017
Amdt 3; amdt 4
Edition 2.5
7
Licensed exclusively to Chavrone Oelofse.
Copying and network storage prohibited.
Edition 2.5
SANS 1083:2017
8
Table 1 (concluded)
1 2 3 4
Class
Fine aggregate derived from the natural disintegration Fine aggregate derived
Property of rock and any mixture (blend) of this class and fine from the mechanical Test method
aggregate derived from the mechanical crushing crushing or milling subclause
or milling of rock of rock
Presence of sugar Free from sugar unless the fine aggregate complies with the 6.9
–
requirement for soluble deleterious impurities.
Soluble deleterious impurities The strength of specimens made with the fine aggregate shall 6.10
be at least 85 % of that of the specimens made with the same
fine aggregate after it has been washed, except that this
–
© SABS
1 2 3 4 5 6 7 8 9 10
Requirement
Test method
Property Nominal size of aggregate
subclause
mm
Grading1), mass percentage of material that passes sieves2) of nominal aperture size,
75,0 53,0 37,5 26,5 19,0 13,2 9,5 6,7
mm 6.2
75,0 100 100
53,0 0 – 50 85 – 100 100
50,0 0 – 43 70 – 85 98 – 100
37,5 0 – 25 0 – 50 85 – 100 100
28,0 0–7 0 – 28 15 – 55 90 – 100
26,5 0–5 0 – 25 0 – 50 85 – 100 100
20,0 0–7 0 – 28 15 – 55 90 – 100
19,0 0–5 0 – 25 0 – 50 85 – 100 100
14,0 0–7 0 – 28 15 – 55 90 – 100
© SABS
SANS 1083:2017
10 % FACT value, of less than 13,2 mm and more than 9,5 mm fraction (dry), kN, min. Coarse aggregate for use in concrete subject to surface abrasion, structural elements of reinforced or prestressed
concrete (or both): 110 6.12
Flakiness index, max. 35 6.13
1) Other gradings are permitted if so required (see annex A). Such a grading shall be specified in terms of the appropriate nominal sizes specified in the table.
Edition 2.5
2) Complying with SANS 3310-1 or SANS 3310-2.
3) Optional alternative to the 10 % FACT value.
Amdt 3; amdt 5
9
Licensed exclusively to Chavrone Oelofse.
Copying and network storage prohibited.
SANS 1083:2017
Edition 2.5
5 Documentation
The following information shall appear on the documents that accompany each delivery of
aggregate or that pertain to each bin or stockpile of aggregate:
b) in the case of fine aggregate, the nominal value for fineness modulus and the maximum chloride
(Cl-) content, as relevant; and
c) in the case of coarse aggregate, the nominal size, the coefficient of uniformity (when relevant),
the proportional blend of nominal sizes (when relevant), and whether the coarse aggregate is
suitable for use in concrete subject to surface abrasion.
6.1 Inspection
Visually examine each delivery of aggregate to ensure that the description of the aggregate
complies with the requirements given in the order or contract and that the aggregate has not been
contaminated with foreign matter.
10 © SABS
Licensed exclusively to Chavrone Oelofse.
Copying and network storage prohibited.
SANS 1083:2017
Edition 2.5
© SABS 11
Licensed exclusively to Chavrone Oelofse.
Copying and network storage prohibited.
SANS 1083:2017
Edition 2.5
Annex A
(normative)
Notes to purchasers
A.1 The following requirements shall be specified in tender invitations and in each order or
contract:
b) the grading limits in respect of aperture sizes 4 750 µm, 2 360 µm, 1 180 µm, 600 µm and
300 µm or 5 mm, 2 mm, 1 mm, 600 µm and 300 µm as referenced in 4.1 of
SANS 3001-AG1:2014, if a specific grading is needed for a specific purpose (see 4.2.2);
Amdt 4
c) when relevant, the range within which the fineness modulus shall fall (see 4.2.4);
A.2 The following requirements shall be agreed upon between the supplier and the purchaser:
a) a permissible variation of the stated coefficient of uniformity (see 4.3.2 and 5(c);
b) the history of the particular aggregate type and source regarding alkali-silica reactivity and, if
available, the latest test results (see C.2.2(k)).
12 © SABS
Licensed exclusively to Chavrone Oelofse.
Copying and network storage prohibited.
SANS 1083:2017
Edition 2.5
Annex B
(informative)
B.1 When a purchaser requires ongoing verification of the quality of aggregates, it is suggested
that, instead of concentrating solely on evaluation of the final product, he also direct his attention to
the manufacturer’s quality system. In this connection it should be noted that SANS 9001 covers the
provision of an integrated system. Amdt 1
B.2 If no information about the implementation of quality control or testing during manufacture is
available to help in the assessing of the quality of a consignment, and a purchaser wishes to
establish by inspection and testing of samples of the final product whether a consignment of the
aggregates complies with this standard, a sampling plan based on applicable statistical principles
should be agreed upon between the supplier and purchaser.
a) such a sampling plan applies only to ready-for-use aggregates sampled in accordance with an
agreed procedure, and
b) if, in terms of the sampling plan, the procedures given in SANS 195 are to be used, a clear
statement should be made as to the objective of the sampling as described in the method.
© SABS 13
Licensed exclusively to Chavrone Oelofse.
Copying and network storage prohibited.
SANS 1083:2017
Edition 2.5
Annex C
(informative)
C.1 General
The notes in this annex are of very general nature, since specific details can best be given in
publications by authorities who possess expert knowledge of the various aspects related to
concrete and its constituents. Information about titles of relevant publications can be obtained from
the above institutions direct or from the SABS Standards Division.
Any information given in the aforementioned publications should not be construed as being
alternative or optional requirements to those given in this standard but as additional information to
assist in the assessment of aggregate for its suitability for use in concrete, especially for special
applications. The determination of properties additional to those covered in this standard should,
wherever possible, be conducted in accordance with national standard methods.
Examples of additional properties that could be considered for determination, and for which
interpretation of the results will be required, are listed below:
c) water absorption;
d) shrinkage;
14 © SABS
Licensed exclusively to Chavrone Oelofse.
Copying and network storage prohibited.
SANS 1083:2017
Edition 2.5
h) friability;
i) abrasion resistance;
j) solubility in acid;
k) alkali-silica reactivity;
l) sand equivalent.
C.3.3 Aggregate that does not comply with the requirements of this standard
If the use of aggregate that does not comply with the requirements of this standard is unavoidable,
utmost care must be taken in the assessment of all the properties of the aggregate, to ensure that
the characteristics of concrete made with the aggregates are not impaired. The long-term durability
of concrete should be considered in particular.
© SABS 15
Licensed exclusively to Chavrone Oelofse.
Copying and network storage prohibited.
SANS 1083:2017
Edition 2.5
Bibliography
SANS 195, Sampling of aggregates.
______________
16 © SABS
Licensed exclusively to Chavrone Oelofse.
Copying and network storage prohibited.
The objective of the SABS Standards Division is to develop, promote and maintain South African
National Standards. This objective is incorporated in the Standards Act, 2008 (Act No. 8 of 2008).
South African National Standards are updated by amendment or revision. Users of South African
National Standards should ensure that they possess the latest amendments or editions.
The SABS continuously strives to improve the quality of its products and services and would
therefore be grateful if anyone finding an inaccuracy or ambiguity while using this standard would
inform the secretary of the technical committee responsible, the identity of which can be found in
the foreword.
The SABS offers an individual notification service, which ensures that subscribers automatically
receive notification regarding amendments and revisions to South African National Standards.
Tel: +27 (0) 12 428 6883 Fax: +27 (0) 12 428 6928 E-mail: sales@sabs.co.za
Buying Standards
Contact the Sales Office for South African and international standards, which are available in both
electronic and hard copy format.
Tel: +27 (0) 12 428 6883 Fax: +27 (0) 12 428 6928 E-mail: sales@sabs.co.za
South African National Standards are also available online from the SABS website
http://www.sabs.co.za
Information on Standards
The Standards Information Centre provides a wide range of standards-related information on both
national and international standards. The Centre also offers an individual updating service called
INFOPLUS, which ensures that subscribers automatically receive notification regarding
amendments to, and revisions of, international standards.
Tel: +27 (0) 12 428 7911 / 0861 27 7227 Fax: +27 (0) 12 428 6928 E-mail: info@sabs.co.za
Copyright
The copyright in a South African National Standard or any other publication published by the SABS
Standards Division vests in the SABS or, in the case of a South African National Standard based on
an international standard, in the organization from which the SABS adopted the standard under
licence or membership agreement. In the latter case, the SABS has the obligation to protect such
copyright. Unless exemption has been granted, no extract may be reproduced, stored in a retrieval
system or transmitted in any form or by any means without prior written permission from the SABS
Standards Division. This does not preclude the free use, in the course of implementing the
standard, of necessary details such as symbols, and size, type or grade designations. If these
details are to be used for any purpose other than implementation, prior written permission must be
obtained.
Details and advice can be obtained from the Manager – Standards Sales and Information Services.
Tel: +27 (0) 12 428 6883 Fax: +27 (0) 12 428 6928 E-mail: sales@sabs.co.za