Professional Documents
Culture Documents
Aruba Lab-6
Aruba Lab-6
===================================================================================
===========================
Lab 6.1: Link Aggregation between Core Switches
===================================================================================
===========================
Objectives
After completing this lab, you will be able to:
• Deploy static Link Aggregation
• Understand the nature of transient loops when creating static aggregations
• Monitor LAG interfaces in AOS-CX
=======================================================
Task 1: Pre-lab Setup:
=======================================================
Objectives
In this activity you will load Lab5-2_final checkpoint in Access-1 and Access-2,
where those two switches were interconnected to the Core switches using ports
1/1/21 and 1/1/22.
NOTE: This activity is dependent on Lab 5.2 configuration, make sure you have
completed that lab before starting the current one. Do not proceed if this is not
the case.
Steps
===================
Access-1 and Access-2
===================
1. Display the checkpoint list and confirm the Lab5-2 checkpoint is there.
********************************************************************************
T11-Access-1# show checkpoint list | include Lab5
T11-Access-2# show checkpoint list | include Lab5
=======================================================
Task 2: Configure Manual Link Aggregation
=======================================================
Steps
===================
PC-3
===================
1. Access PC-3.
===================
Core-1 (via PC-1)
===================
3. Open the SSH session to Core-1.
4. Create LAG 10 interface and apply a description. This will be used as a logical
Layer 2 connection between Cores.
Core-1(config-lag-if)# no routing
Core-1(config-lag-if)# no shutdown
7. Create a port range with interfaces 1/1/43 and 1/1/44 and make these two ports
members of LAG 10.
===================
PC-3
===================
9. Move back to PC-3.
Is the ping still running? -->no
===================
Core-2 (via PC-1)
===================
10. Move to Core-2.
===================
Core-2
===================
13. Move back to Core-2.
14. Repeat steps 4 to 8.
===================
PC-3
===================
12. Move back to PC-3
Is the ping still working ?
=======================================================
Task 3: Normalize Configuration for All Kits.
=======================================================
Objectives
You will now proceed to save your configurations and create checkpoints. Notice
that final
lab checkpoints might be used by later activities.
Steps
===================
PC-1
===================
1. Access PC-1
2. Open the “CXF LAG 10.txt” file located within CXF Student Folder on the desktop.
3. Copy the file contents into the clipboard.
===================
Core-1 and Core-2 (via PC-1)
===================
4. Paste contents on Core-1 and Core-2’s SSH sessions.
Core-1# end
Core-1# configure terminal
Core-1(config)# vlan 111-112,211-212,311-312,411-412,511-512,611-612,711-712,811-
812,911-912,1011-1012,1111-1112,1211-1212,1311-1312,1411-1412
Core-1(config-vlan-<111-112,211-212,311-312,411-412,511-512,611-612,7>)#interface
lag 10
Core-1(config-lag-if)# vlan trunk allowed 111-112,211-212,311-312,411-412,511-
512,611-612,711-712,811-812,911-912,1011-1012,1111-1112,1211-1212,1311-1312,1411-
1412
Core-1(config-lag-if)# end
Core-1# write memory
Core-2# end
Core-2# configure terminal
Core-2(config)# vlan 111-112,211-212,311-312,411-412,511-512,611-612,711-712,811-
812,911-912,1011-1012,1111-1112,1211-1212,1311-1312,1411-1412
Core-2(config-vlan-<111-112,211-212,311-312,411-412,511-512,611-612,7>)#interface
lag 10
Core-2(config-lag-if)# vlan trunk allowed 111-112,211-212,311-312,411-412,511-
512,611-612,711-712,811-812,911-912,1011-1012,1111-1112,1211-1212,1311-1312,1411-
1412
Core-2(config-lag-if)# end
Core-2# write memory
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
You have completed Lab 6.1!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
===================================================================================
===========================
Lab 6.2 Deploying LACP based Link Aggregation
===================================================================================
===========================
Objectives
After completing this lab, you will be able to:
• Deploy LACP based Link Aggregation
• Demonstrate the benefits of LACP vs Static aggregation
=======================================================
Task 1: Pre-lab Setup
=======================================================
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!1
NOTE: This activity uses the same topology you created in Lab 5.3 Task 1
configuration, if you completed that task then feel free to load Lab5-3_task1_done
checkpoints on both Access switches and move to Task 2.
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!1
Steps
===================
Access-1
===================
1. Open a console connection to Access-1. Login using admin and no password.
4. Create a port range including 1/1/27 and 1/1/28, allow VLANs 1, 711 and 712,then
enable them.
===================
Access-2
===================
7. Confirm ports 1/1/21 to 1/1/22 are down and 1/1/27 to 1/1/28 are up.
T11-Access-2(config)# show interface 1/1/21-1/1/22,1/1/27-1/1/28 link-status
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
=======================================================
Task 2: Configure LACP Link Aggregation
=======================================================
Objectives
In the current task you will deploy an aggregated link between both Access Switches
using LACP for negotiating the physical ports’ states.
Steps
===================
Access-1
===================
3. Run Active LACP and fast rate heartbeats on the link aggregation.
********************************************************************************
===================
Access-2
===================
8. Open a console connection to Access-2.
===================
PC-1
===================
13. Open a console session to PC-1.
===================
Access-1 and Access-2
===================
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
You have completed Lab 6.2!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!