Professional Documents
Culture Documents
Structural Pile Calculation Reports
Structural Pile Calculation Reports
For
GENEX INVESTMENT
At
Submitted By
Sanju Jain Geotech Firm (P) Ltd
Bagdol, Lalitpur, Nepal
Email: sconsortium.sanju@gmail.com
Cell 9851118335
May, 2022
GENEX INVESTMENT Project-Structural Pile Calculation reports
UTTAR DHOKA
TABLE OF CONTENTS
1. Vertical Analysis of Single Bored Pile ................................................................................ 2
DEPTH 73
28 15.2 7.6
30 21.0 10.3
31 24.6 12.1
32 29.1 14.2
33 34.5 16.9
34 41.3 20.3
35 49.9 24.6
36 60.9 30.1
37 75.0 37.1
38 93.0 46.1
39 116.1 57.7
GENEX INVESTMENT Project-Structural Pile Calculation reports
UTTAR DHOKA
40 145.4 72.3
Where
Sv = vertical stress in soil
Sh = horizontal stress in soil
Adhesion Ratio Ka
1.5
1.25
1 All Piles
Ratio Ka=Ca/C
Concrete Pile
0.75
0.5
0.25
0
0 1000 2000 3000 4000
Cohesion C, Psf
The equation is different from what shown in DM-7. This equation uses numerical integration, which is more
accurate than the empirical equation in DM-7.
c) Settlement of pile point caused by load transmitted along the pile shaft, Xps
𝐶𝑠 𝑄𝑠
𝑋𝑝𝑠 =
𝐿𝑒 𝑄𝑢𝑙𝑡
Where Le = embedded depth
qult= ultimate end bearing pressure Qs =
side resistance
𝑍
𝐶𝑠 = (0.93 + 0.16)√ 𝐶𝑝
𝐵
Typical settlement against load transfer ratios are shown in Figures 1-2 through 1-5 proposed by Reese
and O’Neal (1988). Figure 1-2 and 1-3 represent the side load transfer ratio for cohesive soils and
cohesion less soils/gravel respectively. Figure 1-4 and 1-5 represent the end bearing load transfer ratio
for cohesive soils and cohesive less soils respectively.
69 | P a g e
GENEX INVESTMENT Project-Structural Pile Calculation reports
UTTAR DHOKA
Qup = Qw + Qside
70 | P a g e
GENEX INVESTMENT Project-Structural Pile Calculation reports
UTTAR DHOKA
𝑑3 𝑌 𝑑𝑌
𝐸𝐼 3
+𝑄 =𝑃
𝑑𝑍 𝑑𝑍
Where P = shear in the pile
Where M = bending moment of the pile
𝑑𝑌
= 𝑆𝑡
𝑑𝑍
Where St = slope of the elastic curve defined by the axis of pile
𝑑2 𝑌
𝐸𝐼 ( 2 ) = 𝑀
𝑑𝑍
71 | P a g e
GENEX INVESTMENT Project-Structural Pile Calculation reports
UTTAR DHOKA
The output of Shear, moment and deflection using the nonlinear differential equations representing the behavior of
the pile -soil system to lateral (shear and moment) loading conditions in a finite difference formulation using Reese’s
p-y method of analysis is presented above in Figure 1-8. For each set of applied boundary loads the program
performs an iterative solution which satisfies static equilibrium and achieves an acceptable compatibility between
force and deflection (p and y) in every element.
72 | P a g e
GENEX INVESTMENT Project-Structural Pile Calculation reports
UTTAR DHOKA
Step 2. Reducing Soil Lateral Resistance by Applying the Deduction Factors from Step 1
Combine the reduction factors and apply them to p-y curve for lateral analysis.
Step 3. Calculate P-yt (the Lateral Capacity and Deflection) of Each Individual Piles
Calculate the lateral capacity of each pile and get P-Yt curve for all piles.
5675
BH-1
UP
MAT:-800mm Assumed for pile tip location
5950
LIFT LIFT
Total:- 4200mm
PARKING
17226 x 15030
56'6" x 49'4"
FFL: -3000
SSL: -3100
2
RAMP CLEAR
3410 MM WIDE
GRADIENT - 1:6
BH-3
PARKING PIT BELOW
BH-2 PARKING PIT BELOW
8330
1
GENEX INVESTMENT Project-Structural Pile Calculation reports
UTTAR DHOKA
77 | P a g e
SUMMARY OF RCC PILE DESIGN FOR GENEX INVESTMENT PROJECT
Lateral Lateral Helical Control
Load Load Longitudinal Rebar
Ultimate Stirrups Stirrups
Clear Ultimate Allowable Carrying Carrying
Grad Ultimate Allowable Axial Vertical
Lengt Cover Vertical Vertical Capacity of Lateral Capacity Factor of
Bored e of Uplift Load Uplift Load Stiffness Load Main
Bore h of from Load Load Pile for Stiffness from FEM Safety in Thro Thro
Pile, Ø, Conc Carrying Carrying of Pile, Carrying Thro Thro Spac Ø, Rebar
ole Pile, Main Carrying Carrying 25mm of Pile, of Pile for RCC bars bars Ø, Spacin %
mm rete, Capacity of Capacity of EA/L, Capacity bars, bars, ing, m
m Bars Capacity, Capacity, deflection KN/mm 25mm design Ø, Ø, mm g, mm
fck, Pile, KN Pile, KN KN/mm from Nos Nos mm m
(mm) KN KN under deflection mm mm
FEM, KN
Ultimate after RCC
Vertical veritificati
1 500 12 75 M25 720.12 437.97 490.430 267.980 295.000 409.062 11.847 295.000 437.970 1.50 6 20 6 25 10 175 16 1000 1.79%
1 500 14 75 M25 772.41 472.82 550.350 301.740 295.000 350.624 11.847 295.000 472.820 1.50 6 20 6 25 10 175 16 1000 1.79%
1 500 16 75 M25 826.58 508.93 612.050 336.380 295.000 306.796 11.847 335.000 479.050 1.50 6 20 6 25 10 175 16 1000 1.79%
3 600 12 75 M25 934.95 572.28 667.260 366.420 405.000 589.049 16.531 495.000 652.280 1.50 6 20 6 25 10 175 16 1000 1.24%
3 600 14 75 M25 987.47 597.66 673.120 374.810 405.000 504.899 16.531 500.000 663.120 1.50 6 20 6 25 10 175 16 1000 1.24%
3 600 16 75 M25 1052.47 641.00 748.980 418.210 405.000 441.786 16.463 515.000 667.980 1.50 6 20 6 25 10 175 16 1000 1.24%
2
Note: Young's Modulus of Concrete M25, E= 5000 𝑓𝑐𝑘 x1000, KN/m2 25,000,000.0000 KN/m
However, at least 2% of the Total number of Piles to be installed at site should be Pile load tested before Construction for its conformity
Safe Load on Piles@ 25mm displacement,tons
Safe load for uplift @ 12mm displacement, Tons
Test Shall be conducted as per IS2911-4-1985 pile load test
Vertical Load- Pile Load Test: The test load shall be maintained for 24 hours.
Initial Tests– The safe load on a single pile shall be the least of the following:
(i) 2/3rd of the final load at which the total displacement attains a value of 12 mm unless otherwise required in a given case on the basis of nature and type of structure in which case,
the safe load should be corresponding to the stated total displacement permissible.
(ii) 50% of the final load at which the total displacement equals 10% of the pile diameter in case of uniform diameter piles or 7.5% of the bulb diameter in case of under reamed piles.
Uplift Load- Pile Load Test: The test load shall be maintained for 24 hours.
The safe load shall be the least of the following:
a) 2/3rd of the load at which the total displacement is 12 mm or the load corresponding to a specified permissible lift.
b) Half of the load at which the load displacement curve shows a clear break.
VERTICAL CAPACITY PILE CALCULATION Ø500mm-12m LONG
USING BH-1 DATA
VERTICAL ANALYSIS Figure 1
Loads:
Load Factor for Vertical Loads= 1.0
Load Factor for Lateral Loads= 1.0
Loads Supported by Pile Cap= 0 %
Shear Condition: Static
Profile:
Pile Length, L= 12.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0
Vertical capacity:
Weight above Ground= 0.00 Total Weight= 45.54-kN *Soil Weight is not included
Side Resistance (Down)= 467.421-kN Side Resistance (Up)= 444.892-kN
Tip Resistance (Down)= 252.702-kN Tip Resistance (Up)= 0.000-kN
Total Ultimate Capacity (Down)= 720.124-kN Total Ultimate Capacity (Up)= 490.429-kN
Total Allowable Capacity (Down)= 437.965-kN Total Allowable Capacity (Up)= 267.983-kN
OK! Qallow > Q
Settlement Calculation:
At Q= 437.00-kN Settlement= 0.09606-cm
At Xallow= 2.50-cm Qallow= 686.64752-kN
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
TOTAL LOADS:
Vertical Load, Q: 437.0 -kN
Load Factor for Vertical Loads: 1.0
Loads Supported by Pile Cap: 0 %
PILE PROFILE:
Pile Length, L= 12.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0.00 Batter Factor, Kbat= 1.00
SINGLE PILE:
Deduction factor due to Group Effect, R= 1.00
Vertical Load= 437.00 -kN
____________________________________________
FACTOR OF SAFETY:
FSside FStip FSuplif FSweight
2.5 2 3 1
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
ALL-PILE Version 6 CivilTech Software www.civiltech.com Licensed to
1 1
3 3
3.0 10.6 27.2 32.6 96.3 0.83 11
Silt (Phi + C)
4 4
6 6
7 7
8 8
9 9
10 10
11 11
11.0 50 3062.7 157.1 320535.8 25000 5.719
Concrete (rough)
12 12
12.0 50 1963.5 157.1 320535.8 25000 5.719 12.0 11.2 0.0 143.0 278.5 0.51 24
Pile Tip Stiff Clay
13 13
14 14
15 15
800
720
640
Compression Load, Qdw -kN
560
480
400
320
240
160
80
0
0.0 0.3 0.5 0.8 1.0 1.3 1.5 1.8 2.0 2.3 2.5 2.8 3.0 3.3 3.5 3.8 4.0 4.3 4.5 4.8 5.0
Settlement, X -cm
Total Side Tip
500 500
450 450
400 400
Compression Capacity, Qdw -kN
350 350
250 250
200 200
150 150
100 100
50 50
0 0
0 2 4 6 8 10 12 14 16 18 20 0 2 4 6 8 10 12 14 16 18 20
Foundation Depth, L -m Foundation Depth, L -m
Loads:
Load Factor for Vertical Loads= 1.0
Load Factor for Lateral Loads= 1.0
Loads Supported by Pile Cap= 0 %
Shear Condition: Static
Profile:
Pile Length, L= 12.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
The Max. Moment calculated by program is an internal force from the applied load conditions. Structural engineer has to check whether
the pile has enough capacity to resist the moment with adequate factor of safety. If not, the pile may fail under the load conditions.
PILE PROFILES:
Pile Length, L= 12.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0.00
SINGLE PILE:
Deduction factor due to Group Effect, R= 1.00
Vertical Load= 437.00 -kN
Shear= 295.00 -kN
Slope Restain, St= 0.00 -cm/-cm
Results:
Top Deflection, yt= 2.49000-cm
Max. Moment, M= 554.00-kN-m
Top Deflection Slope, St= 0.00000
Notes:
Q - Vertical Load at pile top
P - Lateral Shear Load at pile top
M - Moment at pile top
Xall - Pile top total settlement
yt - Pile top deflection
St - Pile top deflection slope (deflection/unit length)
The Max. Moment calculated by program is an internal moment of shaft due to the loading. Egineers
have to check whether the pile has enough moment capacity to resist the Max. Moment with adequate
factor of safety. If not, the pile may be damaged under the loading.
ALL-PILE Version 6 CivilTech Software www.civiltech.com Licensed to
Depth (Zp) DEFLECTION, yt -cm MOMENT -kN-m SHEAR -kN Pressure -kN/m2 Depth (Zp)
from from
Pile Top-m -5.00 0 +5.00 -1000 0 +1000 -500 0 +500 -100 0 +100 Pile Top-m
0 0
1 1
2 2
3 3
4 4
5 5
yt=0 at 5.6-m
6 6
St=0 at 6.7-m
7 7
8 8
9 9
10 10
11 11
12 12
Tip yt=-1.68E-4 Top yt=2.49E+0 Top Moment=-554.0 Top Shear=295.0
Max. yt=2.49E+0 Max. Moment=554.0 Max. Shear=300.0 Max. Pressure=53.00
Top St=1.43E-17
13 13
14 14
15 15
1 1
2 2
3 3
4 4
5 5
6 6
7 7
8 8
9 9
10 10
11 11
12 12
Lateral Slope Vertical yt Slope Max.
No. Load Restraint Load at Top at Top Moment
13 (kN) (cm/cm) (kN) (cm) (cm/cm) (kN-m) 13
1 29.5 0.0 437.0 0.1 0.00 32.7
2 88.5 0.0 437.0 0.4 0.00 131.0
14 3 148.0 0.0 437.0 0.9 0.00 245.0 14
4 206.0 0.0 437.0 1.5 0.00 365.0
5 236.0 0.0 437.0 1.8 0.00 425.0
15 6 266.0 0.0 437.0 2.1 0.00 487.0 15
7 295.0 0.0 437.0 2.5 0.00 554.0
1 1
2 2
3 3
4 4
5 5
6 6
7 7
8 8
9 9
10 10
11 11
12 12
Lateral Slope Vertical yt Slope Max.
No. Load Restraint Load at Top at Top Moment
13 (kN) (cm/cm) (kN) (cm) (cm/cm) (kN-m) 13
1 29.5 0.0 437.0 0.1 0.00 32.7
2 88.5 0.0 437.0 0.4 0.00 131.0
14 3 148.0 0.0 437.0 0.9 0.00 245.0 14
4 206.0 0.0 437.0 1.5 0.00 365.0
5 236.0 0.0 437.0 1.8 0.00 425.0
15 6 266.0 0.0 437.0 2.1 0.00 487.0 15
7 295.0 0.0 437.0 2.5 0.00 554.0
300 300
270 270
240 240
210 210
180 180
Lateral Load, P -kN
120 120
90 90
60 60
30 30
0 0
0.0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0 0 60 120 180 240 300 360 420 480 540 600
Top Deflection, yt -cm Max. Moment in Single Pile, Mmax -kN-m
700000
630000
560000
490000
p, -kN/m
420000
350000
280000
210000
140000
70000
0
0.00 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30 1.40 1.50 1.60 1.70 1.80 1.90 2.00
y, -m
Depth: 1.5, 3.0, 4.5, 6.0, 7.5, 9.0, 10.5 -m
M= 0, P= 295.00 -kN
Results:
At Shear= 295.00-kN, Top Deflection, yt= 12.50000-cm
Stiffness Kpy= 23.60-kN/-cm
At Shear= 295.00-kN, Top Slope, St= -0.03760 Slope
Stiffness Kps= -7845.74-kN/Slope
Or St= -2.15330696 Degree, Stiffness Kps= -137.00-kN/Degree
P= 0, M= 10.00 -kN-m
Results:
At Moment= 10.00-kN, Top Deflection, yt= 0.01690-cm
Stiffness Kmy= 591.72-kN-m/-cm
At Moment= 10.00-kN, Top Slope, St= -0.00020 Slope
Stiffness Kms= -49019.61-kN-m/Slope
Or St= -0.01168834 Degree, Stiffness Kms= -855.55-kN-m/Degree
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
ETABS 18.1.1 License #*1VHQUC7UK2NRLHB
Section Properties
d (mm) h0 (mm) dc (mm) Cover (Torsion) (mm)
500 403.7 96.3 65
Material Properties
Ec (MPa) fck (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
25000 25 1 500 500
Notes:
Loads:
Load Factor for Vertical Loads= 1.0
Load Factor for Lateral Loads= 1.0
Loads Supported by Pile Cap= 0 %
Shear Condition: Static
Profile:
Pile Length, L= 14.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0
Vertical capacity:
Weight above Ground= 0.00 Total Weight= 53.13-kN *Soil Weight is not included
Side Resistance (Down)= 519.708-kN Side Resistance (Up)= 497.221-kN
Tip Resistance (Down)= 252.702-kN Tip Resistance (Up)= 0.000-kN
Total Ultimate Capacity (Down)= 772.411-kN Total Ultimate Capacity (Up)= 550.348-kN
Total Allowable Capacity (Down)= 472.823-kN Total Allowable Capacity (Up)= 301.738-kN
OK! Qallow > Q
Settlement Calculation:
At Q= 472.00-kN Settlement= 0.09712-cm
At Xallow= 2.50-cm Qallow= 733.38062-kN
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
TOTAL LOADS:
Vertical Load, Q: 472.0 -kN
Load Factor for Vertical Loads: 1.0
Loads Supported by Pile Cap: 0 %
PILE PROFILE:
Pile Length, L= 14.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0.00 Batter Factor, Kbat= 1.00
SINGLE PILE:
Deduction factor due to Group Effect, R= 1.00
Vertical Load= 472.00 -kN
____________________________________________
FACTOR OF SAFETY:
FSside FStip FSuplif FSweight
2.5 2 3 1
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
ALL-PILE Version 6 CivilTech Software www.civiltech.com Licensed to
1 1
3 3
3.0 10.6 27.2 32.6 96.3 0.83 11
Silt (Phi + C)
4 4
6 6
7 7
8 8
9 9
10 10
11 11
12 12
13 13
13.0 50 3062.7 157.1 320535.8 25000 5.719
Concrete (rough)
14 14
14.0 50 1963.5 157.1 320535.8 25000 5.719 14.0 11.2 0.0 143.0 278.5 0.51 24
Pile Tip Stiff Clay
15 15
800
720
640
Compression Load, Qdw -kN
560
480
400
320
240
160
80
0
0.0 0.3 0.5 0.8 1.0 1.3 1.5 1.8 2.0 2.3 2.5 2.8 3.0 3.3 3.5 3.8 4.0 4.3 4.5 4.8 5.0
Settlement, X -cm
Total Side Tip
500 500
450 450
400 400
Compression Capacity, Qdw -kN
350 350
250 250
200 200
150 150
100 100
50 50
0 0
0 2 4 6 8 10 12 14 16 18 20 0 2 4 6 8 10 12 14 16 18 20
Foundation Depth, L -m Foundation Depth, L -m
Loads:
Load Factor for Vertical Loads= 1.0
Load Factor for Lateral Loads= 1.0
Loads Supported by Pile Cap= 0 %
Shear Condition: Static
Profile:
Pile Length, L= 14.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
The Max. Moment calculated by program is an internal force from the applied load conditions. Structural engineer has to check whether
the pile has enough capacity to resist the moment with adequate factor of safety. If not, the pile may fail under the load conditions.
PILE PROFILES:
Pile Length, L= 14.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0.00
SINGLE PILE:
Deduction factor due to Group Effect, R= 1.00
Vertical Load= 472.00 -kN
Shear= 290.00 -kN
Slope Restain, St= 0.00 -cm/-cm
Results:
Top Deflection, yt= 2.44000-cm
Max. Moment, M= 544.00-kN-m
Top Deflection Slope, St= 0.00000
Notes:
Q - Vertical Load at pile top
P - Lateral Shear Load at pile top
M - Moment at pile top
Xall - Pile top total settlement
yt - Pile top deflection
St - Pile top deflection slope (deflection/unit length)
The Max. Moment calculated by program is an internal moment of shaft due to the loading. Egineers
have to check whether the pile has enough moment capacity to resist the Max. Moment with adequate
factor of safety. If not, the pile may be damaged under the loading.
ALL-PILE Version 6 CivilTech Software www.civiltech.com Licensed to
Depth (Zp) DEFLECTION, yt -cm MOMENT -kN-m SHEAR -kN Pressure -kN/m2 Depth (Zp)
from from
Pile Top-m -5.00 0 +5.00 -1000 0 +1000 -500 0 +500 -100 0 +100 Pile Top-m
0 0
1 1
2 2
3 3
4 4
5 5
yt=0 at 5.6-m
6 6
St=0 at 6.7-m
7 7
8 8
9 9
10 10
11 11
12 12
13 13
14 14
Tip yt=-2.23E-5 Top yt=2.44E+0 Top Moment=-544.0 Top Shear=290.0
Max. yt=2.44E+0 Max. Moment=544.0 Max. Shear=292.9 Max. Pressure=52.50
Top St=-1.23E-17
15 15
1 1
2 2
3 3
4 4
5 5
6 6
7 7
8 8
9 9
10 10
11 11
12 12
Lateral Slope Vertical yt Slope Max.
No. Load Restraint Load at Top at Top Moment
13 (kN) (cm/cm) (kN) (cm) (cm/cm) (kN-m) 13
1 29.0 0.0 472.0 0.1 0.00 32.1
2 87.0 0.0 472.0 0.4 0.00 129.0
14 3 145.0 0.0 472.0 0.9 0.00 241.0 14
4 203.0 0.0 472.0 1.5 0.00 359.0
5 232.0 0.0 472.0 1.8 0.00 418.0
15 6 261.0 0.0 472.0 2.1 0.00 479.0 15
7 290.0 0.0 472.0 2.4 0.00 544.0
1 1
2 2
3 3
4 4
5 5
6 6
7 7
8 8
9 9
10 10
11 11
12 12
Lateral Slope Vertical yt Slope Max.
No. Load Restraint Load at Top at Top Moment
13 (kN) (cm/cm) (kN) (cm) (cm/cm) (kN-m) 13
1 29.0 0.0 472.0 0.1 0.00 32.1
2 87.0 0.0 472.0 0.4 0.00 129.0
14 3 145.0 0.0 472.0 0.9 0.00 241.0 14
4 203.0 0.0 472.0 1.5 0.00 359.0
5 232.0 0.0 472.0 1.8 0.00 418.0
15 6 261.0 0.0 472.0 2.1 0.00 479.0 15
7 290.0 0.0 472.0 2.4 0.00 544.0
300 300
270 270
240 240
210 210
180 180
Lateral Load, P -kN
120 120
90 90
60 60
30 30
0 0
0.0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0 0 60 120 180 240 300 360 420 480 540 600
Top Deflection, yt -cm Max. Moment in Single Pile, Mmax -kN-m
300
270
240
210
p, -kN/m
180
150
120
90
60
30
0
0.00 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30 1.40 1.50 1.60 1.70 1.80 1.90 2.00
y, -m
Depth: 1.8, 3.5, 5.3, 7.0, 8.8, 10.5, 12.3 -m
M= 0, P= 290.00 -kN
Results:
At Shear= 290.00-kN, Top Deflection, yt= 12.30000-cm
Stiffness Kpy= 23.58-kN/-cm
At Shear= 290.00-kN, Top Slope, St= -0.03690 Slope
Stiffness Kps= -7859.08-kN/Slope
Or St= -2.11325550 Degree, Stiffness Kps= -137.23-kN/Degree
P= 0, M= 10.00 -kN-m
Results:
At Moment= 10.00-kN, Top Deflection, yt= 0.01690-cm
Stiffness Kmy= 591.72-kN-m/-cm
At Moment= 10.00-kN, Top Slope, St= -0.00020 Slope
Stiffness Kms= -49019.61-kN-m/Slope
Or St= -0.01168834 Degree, Stiffness Kms= -855.55-kN-m/Degree
M= 0, P= 290.00 -kN
Results:
At Shear= 290.00-kN, Top Deflection, yt= 2.44000-cm
Stiffness Kpy= 118.85-kN/-cm
At Shear= 290.00-kN, Top Slope, St= 0.00000
Stiffness Kps= N/A
P= 0, M= 10.00 -kN-m
Results:
At Moment= 10.00-kN, Top Deflection, yt= 0.00000-cm
Stiffness Kmy= N/A
At Moment= 10.00-kN, Top Slope, St= 0.00000
Stiffness Kms= N/A
Notes:
Q - Vertical Load at pile top
P - Lateral Shear Load at pile top
M - Moment at pile top
Xall - Pile top total settlement
yt - Pile top deflection
St - Pile top deflection slope (deflection/unit length). Clockwise is negative
Kqx - Secant Stiffness: Vertical load vs. Vertical movement (settlement)
Kpy - Secant Stiffness: Lateral Shear vs. Lateral movement (deflection)
Kps - Secant Stiffness: Lateral Shear vs. Slope (rotation). Clockwise is negative
Kmy - Secant Stiffness: Moment vs. Lateral movement (deflection)
Kms - Secant Stiffness: Moment vs. Slope (rotation). Clockwise is negative
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
ETABS 18.1.1 License #*1VHQUC7UK2NRLHB
Section Properties
d (mm) h0 (mm) dc (mm) Cover (Torsion) (mm)
600 503.7 96.3 65
Material Properties
Ec (MPa) fck (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
25000 25 1 500 500
Notes:
Loads:
Load Factor for Vertical Loads= 1.0
Load Factor for Lateral Loads= 1.0
Loads Supported by Pile Cap= 0 %
Shear Condition: Static
Profile:
Pile Length, L= 16.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0
Vertical capacity:
Weight above Ground= 0.00 Total Weight= 60.72-kN *Soil Weight is not included
Side Resistance (Down)= 573.874-kN Side Resistance (Up)= 551.336-kN
Tip Resistance (Down)= 252.702-kN Tip Resistance (Up)= 0.000-kN
Total Ultimate Capacity (Down)= 826.577-kN Total Ultimate Capacity (Up)= 612.053-kN
Total Allowable Capacity (Down)= 508.934-kN Total Allowable Capacity (Up)= 336.385-kN
OK! Qallow > Q
Settlement Calculation:
At Q= 508.00-kN Settlement= 0.10006-cm
At Xallow= 2.50-cm Qallow= 779.01764-kN
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
TOTAL LOADS:
Vertical Load, Q: 508.0 -kN
Load Factor for Vertical Loads: 1.0
Loads Supported by Pile Cap: 0 %
PILE PROFILE:
Pile Length, L= 16.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0.00 Batter Factor, Kbat= 1.00
SINGLE PILE:
Deduction factor due to Group Effect, R= 1.00
Vertical Load= 508.00 -kN
____________________________________________
FACTOR OF SAFETY:
FSside FStip FSuplif FSweight
2.5 2 3 1
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
ALL-PILE Version 6 CivilTech Software www.civiltech.com Licensed to
8 8
10 10
12 12
14 14
20 20
22 22
24 24
26 26
28 28
30 30
900
810
720
Compression Load, Qdw -kN
630
540
450
360
270
180
90
0
0.0 0.3 0.5 0.8 1.0 1.3 1.5 1.8 2.0 2.3 2.5 2.8 3.0 3.3 3.5 3.8 4.0 4.3 4.5 4.8 5.0
Settlement, X -cm
Total Side Tip
600 600
540 540
480 480
Compression Capacity, Qdw -kN
420 420
300 300
240 240
180 180
120 120
60 60
0 0
0 2 4 6 8 10 12 14 16 18 20 0 2 4 6 8 10 12 14 16 18 20
Foundation Depth, L -m Foundation Depth, L -m
Loads:
Load Factor for Vertical Loads= 1.0
Load Factor for Lateral Loads= 1.0
Loads Supported by Pile Cap= 0 %
Shear Condition: Static
Profile:
Pile Length, L= 16.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
The Max. Moment calculated by program is an internal force from the applied load conditions. Structural engineer has to check whether
the pile has enough capacity to resist the moment with adequate factor of safety. If not, the pile may fail under the load conditions.
PILE PROFILES:
Pile Length, L= 16.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0.00
SINGLE PILE:
Deduction factor due to Group Effect, R= 1.00
Vertical Load= 508.00 -kN
Shear= 295.00 -kN
Slope Restain, St= 0.00 -cm/-cm
Results:
Top Deflection, yt= 2.49000-cm
Max. Moment, M= 554.00-kN-m
Top Deflection Slope, St= 0.00000
Notes:
Q - Vertical Load at pile top
P - Lateral Shear Load at pile top
M - Moment at pile top
Xall - Pile top total settlement
yt - Pile top deflection
St - Pile top deflection slope (deflection/unit length)
The Max. Moment calculated by program is an internal moment of shaft due to the loading. Egineers
have to check whether the pile has enough moment capacity to resist the Max. Moment with adequate
factor of safety. If not, the pile may be damaged under the loading.
ALL-PILE Version 6 CivilTech Software www.civiltech.com Licensed to
Depth (Zp) DEFLECTION, yt -cm MOMENT -kN-m SHEAR -kN Pressure -kN/m2 Depth (Zp)
from from
Pile Top-m -5.00 0 +5.00 -1000 0 +1000 -500 0 +500 -100 0 +100 Pile Top-m
0 0
2 2
4 4
yt=0 at 5.6-m
6 6
St=0 at 6.7-m
8 8
10 10
12 12
14 14
16 16
Tip yt=3.8E-6 Top yt=2.49E+0 Top Moment=-554.0 Top Shear=295.0
Max. yt=2.49E+0 Max. Moment=554.0 Max. Shear=300.0 Max. Pressure=53.00
Top St=2.15E-17
18 18
20 20
22 22
24 24
26 26
28 28
30 30
2 2
4 4
6 6
8 8
10 10
12 12
14 14
16 16
18 18
20 20
22 22
24 24
Lateral Slope Vertical yt Slope Max.
No. Load Restraint Load at Top at Top Moment
26 (kN) (cm/cm) (kN) (cm) (cm/cm) (kN-m) 26
1 29.5 0.0 508.0 0.1 0.00 32.7
2 88.5 0.0 508.0 0.4 0.00 131.0
28 3 148.0 0.0 508.0 0.9 0.00 245.0 28
4 206.0 0.0 508.0 1.5 0.00 365.0
5 236.0 0.0 508.0 1.8 0.00 425.0
30 6 266.0 0.0 508.0 2.1 0.00 487.0 30
7 295.0 0.0 508.0 2.5 0.00 554.0
2 2
4 4
6 6
8 8
10 10
12 12
14 14
16 16
18 18
20 20
22 22
24 24
Lateral Slope Vertical yt Slope Max.
No. Load Restraint Load at Top at Top Moment
26 (kN) (cm/cm) (kN) (cm) (cm/cm) (kN-m) 26
1 29.5 0.0 508.0 0.1 0.00 32.7
2 88.5 0.0 508.0 0.4 0.00 131.0
28 3 148.0 0.0 508.0 0.9 0.00 245.0 28
4 206.0 0.0 508.0 1.5 0.00 365.0
5 236.0 0.0 508.0 1.8 0.00 425.0
30 6 266.0 0.0 508.0 2.1 0.00 487.0 30
7 295.0 0.0 508.0 2.5 0.00 554.0
300 300
270 270
240 240
210 210
180 180
Lateral Load, P -kN
120 120
90 90
60 60
30 30
0 0
0.0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0 0 60 120 180 240 300 360 420 480 540 600
Top Deflection, yt -cm Max. Moment in Single Pile, Mmax -kN-m
300
270
240
210
p, -kN/m
180
150
120
90
60
30
0
0.00 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30 1.40 1.50 1.60 1.70 1.80 1.90 2.00
y, -m
Depth: 2.0, 4.0, 6.0, 8.0, 10.0, 12.0, 14.0 -m
M= 0, P= 295.00 -kN
Results:
At Shear= 295.00-kN, Top Deflection, yt= 12.70000-cm
Stiffness Kpy= 23.23-kN/-cm
At Shear= 295.00-kN, Top Slope, St= -0.03810 Slope
Stiffness Kps= -7742.78-kN/Slope
Or St= -2.18191385 Degree, Stiffness Kps= -135.20-kN/Degree
P= 0, M= 10.00 -kN-m
Results:
At Moment= 10.00-kN, Top Deflection, yt= 0.01700-cm
Stiffness Kmy= 588.24-kN-m/-cm
At Moment= 10.00-kN, Top Slope, St= -0.00021 Slope
Stiffness Kms= -48780.49-kN-m/Slope
Or St= -0.01174563 Degree, Stiffness Kms= -851.38-kN-m/Degree
M= 0, P= 295.00 -kN
Results:
At Shear= 295.00-kN, Top Deflection, yt= 2.49000-cm
Stiffness Kpy= 118.47-kN/-cm
At Shear= 295.00-kN, Top Slope, St= 0.00000
Stiffness Kps= N/A
P= 0, M= 10.00 -kN-m
Results:
At Moment= 10.00-kN, Top Deflection, yt= 0.00000-cm
Stiffness Kmy= N/A
At Moment= 10.00-kN, Top Slope, St= 0.00000
Stiffness Kms= N/A
Notes:
Q - Vertical Load at pile top
P - Lateral Shear Load at pile top
M - Moment at pile top
Xall - Pile top total settlement
yt - Pile top deflection
St - Pile top deflection slope (deflection/unit length). Clockwise is negative
Kqx - Secant Stiffness: Vertical load vs. Vertical movement (settlement)
Kpy - Secant Stiffness: Lateral Shear vs. Lateral movement (deflection)
Kps - Secant Stiffness: Lateral Shear vs. Slope (rotation). Clockwise is negative
Kmy - Secant Stiffness: Moment vs. Lateral movement (deflection)
Kms - Secant Stiffness: Moment vs. Slope (rotation). Clockwise is negative
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
VERTICAL CAPACITY PILE CALCULATION Ø600mm-12m LONG
USING BH-1 DATA
VERTICAL ANALYSIS Figure 1
Loads:
Load Factor for Vertical Loads= 1.0
Load Factor for Lateral Loads= 1.0
Loads Supported by Pile Cap= 0 %
Shear Condition: Static
Profile:
Pile Length, L= 12.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0
Vertical capacity:
Weight above Ground= 0.00 Total Weight= 65.58-kN *Soil Weight is not included
Side Resistance (Down)= 628.824-kN Side Resistance (Up)= 601.682-kN
Tip Resistance (Down)= 306.123-kN Tip Resistance (Up)= 0.000-kN
Total Ultimate Capacity (Down)= 934.946-kN Total Ultimate Capacity (Up)= 667.264-kN
Total Allowable Capacity (Down)= 572.277-kN Total Allowable Capacity (Up)= 366.423-kN
OK! Qallow > Q
Settlement Calculation:
At Q= 570.00-kN Settlement= 0.11067-cm
At Xallow= 2.50-cm Qallow= 909.28967-kN
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
OTAL LOADS:
Vertical Load, Q: 570.0 -kN
Load Factor for Vertical Loads: 1.0
Loads Supported by Pile Cap: 0 %
PILE PROFILE:
Pile Length, L= 12.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0.00 Batter Factor, Kbat= 1.00
SINGLE PILE:
Deduction factor due to Group Effect, R= 1.00
Vertical Load= 570.00 -kN
____________________________________________
FACTOR OF SAFETY:
FSside FStip FSuplif FSweight
2.5 2 3 1
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
ALL-PILE Version 6 CivilTech Software www.civiltech.com Licensed to
1 1
3 3
3.0 10.4 29.5 27.5 75.1 0.92 9
Silt (Phi + C)
4 4
6 6
7 7
8 8
9 9
10 10
11 11
11.0 60 4410.2 188.5 664662.9 25000 8.236
Concrete (rough)
12 12
12.0 60 2827.4 188.5 664662.9 25000 7.069 12.0 11.0 0.0 120.3 222.4 0.57 20
Pile Tip Stiff Clay
13 13
14 14
15 15
1000
900
800
Compression Load, Qdw -kN
700
600
500
400
300
200
100
0
0.0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0 3.3 3.6 3.9 4.2 4.5 4.8 5.1 5.4 5.7 6.0
Settlement, X -cm
Total Side Tip
600 600
540 540
480 480
Compression Capacity, Qdw -kN
420 420
300 300
240 240
180 180
120 120
60 60
0 0
0 2 4 6 8 10 12 14 16 18 20 0 2 4 6 8 10 12 14 16 18 20
Foundation Depth, L -m Foundation Depth, L -m
Loads:
Load Factor for Vertical Loads= 1.0
Load Factor for Lateral Loads= 1.0
Loads Supported by Pile Cap= 0 %
Shear Condition: Static
Profile:
Pile Length, L= 12.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
The Max. Moment calculated by program is an internal force from the applied load conditions. Structural engineer has to check whether
the pile has enough capacity to resist the moment with adequate factor of safety. If not, the pile may fail under the load conditions.
ILE PROFILES:
Pile Length, L= 12.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0.00
SINGLE PILE:
Deduction factor due to Group Effect, R= 1.00
Vertical Load= 555.00 -kN
Shear= 405.00 -kN
Slope Restain, St= 0.00 -cm/-cm
Results:
Top Deflection, yt= 2.45000-cm
Max. Moment, M= 860.00-kN-m
Top Deflection Slope, St= 0.00000
Notes:
Q - Vertical Load at pile top
P - Lateral Shear Load at pile top
M - Moment at pile top
Xall - Pile top total settlement
yt - Pile top deflection
St - Pile top deflection slope (deflection/unit length)
The Max. Moment calculated by program is an internal moment of shaft due to the loading. Egineers
have to check whether the pile has enough moment capacity to resist the Max. Moment with adequate
factor of safety. If not, the pile may be damaged under the loading.
ALL-PILE Version 6 CivilTech Software www.civiltech.com Licensed to
Depth (Zp) DEFLECTION, yt -cm MOMENT -kN-m SHEAR -kN Pressure -kN/m2 Depth (Zp)
from from
Pile Top-m -5.00 0 +5.00 -1000 0 +1000 -500 0 +500 -100 0 +100 Pile Top-m
0 0
1 1
2 2
3 3
4 4
5 5
6 6
yt=0 at 6.4-m
St=0 at 0.1-m
7 7
8 8
9 9
10 10
11 11
12 12
Tip yt=7.32E-3 Top yt=2.45E+0 Top Moment=-860.0 Top Shear=405.0
Max. yt=2.45E+0 Max. Moment=860.0 Max. Shear=408.3 Max. Pressure=52.08
Top St=1.43E-17
13 13
14 14
15 15
1 1
2 2
3 3
4 4
5 5
6 6
7 7
8 8
9 9
10 10
11 11
12 12
Lateral Slope Vertical yt Slope Max.
No. Load Restraint Load at Top at Top Moment
13 (kN) (cm/cm) (kN) (cm) (cm/cm) (kN-m) 13
1 40.5 0.0 555.0 0.1 0.00 49.9
2 122.0 0.0 555.0 0.4 0.00 203.0
14 3 202.0 0.0 555.0 0.9 0.00 380.0 14
4 284.0 0.0 555.0 1.5 0.00 569.0
5 324.0 0.0 555.0 1.8 0.00 665.0
15 6 364.0 0.0 555.0 2.1 0.00 762.0 15
7 405.0 0.0 555.0 2.5 0.00 860.0
1 1
2 2
3 3
4 4
5 5
6 6
7 7
8 8
9 9
10 10
11 11
12 12
Lateral Slope Vertical yt Slope Max.
No. Load Restraint Load at Top at Top Moment
13 (kN) (cm/cm) (kN) (cm) (cm/cm) (kN-m) 13
1 40.5 0.0 555.0 0.1 0.00 49.9
2 122.0 0.0 555.0 0.4 0.00 203.0
14 3 202.0 0.0 555.0 0.9 0.00 380.0 14
4 284.0 0.0 555.0 1.5 0.00 569.0
5 324.0 0.0 555.0 1.8 0.00 665.0
15 6 364.0 0.0 555.0 2.1 0.00 762.0 15
7 405.0 0.0 555.0 2.5 0.00 860.0
500 500
450 450
400 400
350 350
300 300
Lateral Load, P -kN
200 200
150 150
100 100
50 50
0 0
0.0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0 0 90 180 270 360 450 540 630 720 810 900
Top Deflection, yt -cm Max. Moment in Single Pile, Mmax -kN-m
800000
720000
640000
560000
p, -kN/m
480000
400000
320000
240000
160000
80000
0
0.00 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30 1.40 1.50 1.60 1.70 1.80 1.90 2.00
y, -m
Depth: 1.5, 3.0, 4.5, 6.0, 7.5, 9.0, 10.5 -m
M= 0, P= 405.00 -kN
Results:
At Shear= 405.00-kN, Top Deflection, yt= 11.50000-cm
Stiffness Kpy= 35.22-kN/-cm
At Shear= 405.00-kN, Top Slope, St= -0.03060 Slope
Stiffness Kps= -13235.29-kN/Slope
Or St= -1.75270391 Degree, Stiffness Kps= -231.07-kN/Degree
P= 0, M= 10.00 -kN-m
Results:
At Moment= 10.00-kN, Top Deflection, yt= 0.00973-cm
Stiffness Kmy= 1027.75-kN-m/-cm
At Moment= 10.00-kN, Top Slope, St= -0.00010 Slope
Stiffness Kms= -96153.84-kN-m/Slope
Or St= -0.00595876 Degree, Stiffness Kms= -1678.20-kN-m/Degree
M= 0, P= 405.00 -kN
Results:
At Shear= 405.00-kN, Top Deflection, yt= 2.45000-cm
Stiffness Kpy= 165.31-kN/-cm
At Shear= 405.00-kN, Top Slope, St= 0.00000
Stiffness Kps= N/A
P= 0, M= 10.00 -kN-m
Results:
At Moment= 10.00-kN, Top Deflection, yt= 0.00000-cm
Stiffness Kmy= N/A
At Moment= 10.00-kN, Top Slope, St= 0.00000
Stiffness Kms= N/A
Notes:
Q - Vertical Load at pile top
P - Lateral Shear Load at pile top
M - Moment at pile top
Xall - Pile top total settlement
yt - Pile top deflection
St - Pile top deflection slope (deflection/unit length). Clockwise is negative
Kqx - Secant Stiffness: Vertical load vs. Vertical movement (settlement)
Kpy - Secant Stiffness: Lateral Shear vs. Lateral movement (deflection)
Kps - Secant Stiffness: Lateral Shear vs. Slope (rotation). Clockwise is negative
Kmy - Secant Stiffness: Moment vs. Lateral movement (deflection)
Kms - Secant Stiffness: Moment vs. Slope (rotation). Clockwise is negative
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
ETABS 18.1.1 License #*1VHQUC7UK2NRLHB
Section Properties
d (mm) h0 (mm) dc (mm) Cover (Torsion) (mm)
500 403.7 96.3 65
Material Properties
Ec (MPa) fck (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
25000 25 1 500 500
Notes:
Loads:
Load Factor for Vertical Loads= 1.0
Load Factor for Lateral Loads= 1.0
Loads Supported by Pile Cap= 0 %
Shear Condition: Static
Profile:
Pile Length, L= 14.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0
Vertical capacity:
Weight above Ground= 0.00 Total Weight= 76.51-kN *Soil Weight is not included
Side Resistance (Down)= 623.581-kN Side Resistance (Up)= 596.604-kN
Tip Resistance (Down)= 363.886-kN Tip Resistance (Up)= 0.000-kN
Total Ultimate Capacity (Down)= 987.468-kN Total Ultimate Capacity (Up)= 673.116-kN
Total Allowable Capacity (Down)= 597.664-kN Total Allowable Capacity (Up)= 374.814-kN
OK! Qallow > Q
Settlement Calculation:
At Q= 595.00-kN Settlement= 0.11533-cm
At Xallow= 2.50-cm Qallow= 964.73578-kN
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
TOTAL LOADS:
Vertical Load, Q: 595.0 -kN
Load Factor for Vertical Loads: 1.0
Loads Supported by Pile Cap: 0 %
PILE PROFILE:
Pile Length, L= 14.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0.00 Batter Factor, Kbat= 1.00
SINGLE PILE:
Deduction factor due to Group Effect, R= 1.00
Vertical Load= 595.00 -kN
____________________________________________
FACTOR OF SAFETY:
FSside FStip FSuplif FSweight
2.5 2 3 1
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
ALL-PILE Version 6 CivilTech Software www.civiltech.com Licensed to
1 1
3 3
3.0 10.6 27.2 32.6 96.3 0.83 11
Silt (Phi + C)
4 4
6 6
7 7
8 8
9 9
10 10
11 11
12 12
13 13
13.0 60 4410.2 188.5 664662.9 25000 8.236
Concrete (rough)
14 14
14.0 60 4410.2 188.5 664662.9 25000 7.069 14.0 11.2 0.0 143.0 278.5 0.51 24
Pile Tip Stiff Clay
15 15
1000
900
800
Compression Load, Qdw -kN
700
600
500
400
300
200
100
0
0.0 0.3 0.5 0.8 1.0 1.3 1.5 1.8 2.0 2.3 2.5 2.8 3.0 3.3 3.5 3.8 4.0 4.3 4.5 4.8 5.0
Settlement, X -cm
Total Side Tip
600 600
540 540
480 480
Compression Capacity, Qdw -kN
420 420
300 300
240 240
180 180
120 120
60 60
0 0
0 2 4 6 8 10 12 14 16 18 20 0 2 4 6 8 10 12 14 16 18 20
Foundation Depth, L -m Foundation Depth, L -m
Loads:
Load Factor for Vertical Loads= 1.0
Load Factor for Lateral Loads= 1.0
Loads Supported by Pile Cap= 0 %
Shear Condition: Static
Profile:
Pile Length, L= 14.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
The Max. Moment calculated by program is an internal force from the applied load conditions. Structural engineer has to check whether
the pile has enough capacity to resist the moment with adequate factor of safety. If not, the pile may fail under the load conditions.
ILE PROFILES:
Pile Length, L= 14.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0.00
SINGLE PILE:
Deduction factor due to Group Effect, R= 1.00
Vertical Load= 595.00 -kN
Shear= 400.00 -kN
Slope Restain, St= 0.00 -cm/-cm
Results:
Top Deflection, yt= 2.42000-cm
Max. Moment, M= 849.00-kN-m
Top Deflection Slope, St= 0.00000
Notes:
Q - Vertical Load at pile top
P - Lateral Shear Load at pile top
M - Moment at pile top
Xall - Pile top total settlement
yt - Pile top deflection
St - Pile top deflection slope (deflection/unit length)
The Max. Moment calculated by program is an internal moment of shaft due to the loading. Egineers
have to check whether the pile has enough moment capacity to resist the Max. Moment with adequate
factor of safety. If not, the pile may be damaged under the loading.
ALL-PILE Version 6 CivilTech Software www.civiltech.com Licensed to
Depth (Zp) DEFLECTION, yt -cm MOMENT -kN-m SHEAR -kN Pressure -kN/m2 Depth (Zp)
from from
Pile Top-m -5.00 0 +5.00 -1000 0 +1000 -500 0 +500 -100 0 +100 Pile Top-m
0 0
1 1
2 2
3 3
4 4
5 5
6 6
yt=0 at 6.4-m
St=0 at 0.1-m
7 7
8 8
9 9
10 10
11 11
12 12
13 13
14 14
Tip yt=-1.79E-4 Top yt=2.42E+0 Top Moment=-849.0 Top Shear=400.0
Max. yt=2.42E+0 Max. Moment=849.0 Max. Shear=407.1 Max. Pressure=51.67
Top St=0E+0
15 15
1 1
2 2
3 3
4 4
5 5
6 6
7 7
8 8
9 9
10 10
11 11
12 12
Lateral Slope Vertical yt Slope Max.
No. Load Restraint Load at Top at Top Moment
13 (kN) (cm/cm) (kN) (cm) (cm/cm) (kN-m) 13
1 40.0 0.0 595.0 0.1 0.00 49.3
2 120.0 0.0 595.0 0.4 0.00 200.0
14 3 200.0 0.0 595.0 0.9 0.00 375.0 14
4 280.0 0.0 595.0 1.5 0.00 562.0
5 320.0 0.0 595.0 1.8 0.00 657.0
15 6 360.0 0.0 595.0 2.1 0.00 753.0 15
7 400.0 0.0 595.0 2.4 0.00 849.0
1 1
2 2
3 3
4 4
5 5
6 6
7 7
8 8
9 9
10 10
11 11
12 12
Lateral Slope Vertical yt Slope Max.
No. Load Restraint Load at Top at Top Moment
13 (kN) (cm/cm) (kN) (cm) (cm/cm) (kN-m) 13
1 40.0 0.0 595.0 0.1 0.00 49.3
2 120.0 0.0 595.0 0.4 0.00 200.0
14 3 200.0 0.0 595.0 0.9 0.00 375.0 14
4 280.0 0.0 595.0 1.5 0.00 562.0
5 320.0 0.0 595.0 1.8 0.00 657.0
15 6 360.0 0.0 595.0 2.1 0.00 753.0 15
7 400.0 0.0 595.0 2.4 0.00 849.0
400 400
360 360
320 320
280 280
240 240
Lateral Load, P -kN
160 160
120 120
80 80
40 40
0 0
0.0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0 0 90 180 270 360 450 540 630 720 810 900
Top Deflection, yt -cm Max. Moment in Single Pile, Mmax -kN-m
300
270
240
210
p, -kN/m
180
150
120
90
60
30
0
0.00 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30 1.40 1.50 1.60 1.70 1.80 1.90 2.00
y, -m
Depth: 1.8, 3.5, 5.3, 7.0, 8.8, 10.5, 12.3 -m
M= 0, P= 400.00 -kN
Results:
At Shear= 400.00-kN, Top Deflection, yt= 11.40000-cm
Stiffness Kpy= 35.09-kN/-cm
At Shear= 400.00-kN, Top Slope, St= -0.03020 Slope
Stiffness Kps= -13245.03-kN/Slope
Or St= -1.72980678 Degree, Stiffness Kps= -231.24-kN/Degree
P= 0, M= 10.00 -kN-m
Results:
At Moment= 10.00-kN, Top Deflection, yt= 0.00970-cm
Stiffness Kmy= 1030.93-kN-m/-cm
At Moment= 10.00-kN, Top Slope, St= -0.00010 Slope
Stiffness Kms= -96153.84-kN-m/Slope
Or St= -0.00595876 Degree, Stiffness Kms= -1678.20-kN-m/Degree
M= 0, P= 400.00 -kN
Results:
At Shear= 400.00-kN, Top Deflection, yt= 2.42000-cm
Stiffness Kpy= 165.29-kN/-cm
At Shear= 400.00-kN, Top Slope, St= 0.00000
Stiffness Kps= N/A
P= 0, M= 10.00 -kN-m
Results:
At Moment= 10.00-kN, Top Deflection, yt= 0.00000-cm
Stiffness Kmy= N/A
At Moment= 10.00-kN, Top Slope, St= 0.00000
Stiffness Kms= N/A
Notes:
Q - Vertical Load at pile top
P - Lateral Shear Load at pile top
M - Moment at pile top
Xall - Pile top total settlement
yt - Pile top deflection
St - Pile top deflection slope (deflection/unit length). Clockwise is negative
Kqx - Secant Stiffness: Vertical load vs. Vertical movement (settlement)
Kpy - Secant Stiffness: Lateral Shear vs. Lateral movement (deflection)
Kps - Secant Stiffness: Lateral Shear vs. Slope (rotation). Clockwise is negative
Kmy - Secant Stiffness: Moment vs. Lateral movement (deflection)
Kms - Secant Stiffness: Moment vs. Slope (rotation). Clockwise is negative
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
VERTICAL CAPACITY PILE CALCULATION Ø600mm-16m LONG
USING BH-1 DATA
VERTICAL ANALYSIS Figure 1
Loads:
Load Factor for Vertical Loads= 1.0
Load Factor for Lateral Loads= 1.0
Loads Supported by Pile Cap= 0 %
Shear Condition: Static
Profile:
Pile Length, L= 16.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0
Vertical capacity:
Weight above Ground= 0.00 Total Weight= 87.44-kN *Soil Weight is not included
Side Resistance (Down)= 688.583-kN Side Resistance (Up)= 661.535-kN
Tip Resistance (Down)= 363.886-kN Tip Resistance (Up)= 0.000-kN
Total Ultimate Capacity (Down)= 1052.470-kN Total Ultimate Capacity (Up)= 748.977-kN
Total Allowable Capacity (Down)= 640.999-kN Total Allowable Capacity (Up)= 418.210-kN
OK! Qallow > Q
Settlement Calculation:
At Q= 640.00-kN Settlement= 0.11654-cm
At Xallow= 2.50-cm Qallow= 1025.34253-kN
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
TOTAL LOADS:
Vertical Load, Q: 641.0 -kN
Load Factor for Vertical Loads: 1.0
Loads Supported by Pile Cap: 0 %
PILE PROFILE:
Pile Length, L= 16.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0.00 Batter Factor, Kbat= 1.00
SINGLE PILE:
Deduction factor due to Group Effect, R= 1.00
Vertical Load= 641.00 -kN
____________________________________________
FACTOR OF SAFETY:
FSside FStip FSuplif FSweight
2.5 2 3 1
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
ALL-PILE Version 6 CivilTech Software www.civiltech.com Licensed to
8 8
10 10
12 12
14 14
20 20
22 22
24 24
26 26
28 28
30 30
2000
1800
1600
Compression Load, Qdw -kN
1400
1200
1000
800
600
400
200
0
0.0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0 3.3 3.6 3.9 4.2 4.5 4.8 5.1 5.4 5.7 6.0
Settlement, X -cm
Total Side Tip
700 700
630 630
560 560
Compression Capacity, Qdw -kN
490 490
350 350
280 280
210 210
140 140
70 70
0 0
0 2 4 6 8 10 12 14 16 18 20 0 2 4 6 8 10 12 14 16 18 20
Foundation Depth, L -m Foundation Depth, L -m
Loads:
Load Factor for Vertical Loads= 1.0
Load Factor for Lateral Loads= 1.0
Loads Supported by Pile Cap= 0 %
Shear Condition: Static
Profile:
Pile Length, L= 16.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
The Max. Moment calculated by program is an internal force from the applied load conditions. Structural engineer has to check whether
the pile has enough capacity to resist the moment with adequate factor of safety. If not, the pile may fail under the load conditions.
PILE PROFILES:
Pile Length, L= 16.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0.00
SINGLE PILE:
Deduction factor due to Group Effect, R= 1.00
Vertical Load= 640.00 -kN
Shear= 405.00 -kN
Slope Restain, St= 0.00 -cm/-cm
Results:
Top Deflection, yt= 2.46000-cm
Max. Moment, M= 860.00-kN-m
Top Deflection Slope, St= 0.00000
Notes:
Q - Vertical Load at pile top
P - Lateral Shear Load at pile top
M - Moment at pile top
Xall - Pile top total settlement
yt - Pile top deflection
St - Pile top deflection slope (deflection/unit length)
The Max. Moment calculated by program is an internal moment of shaft due to the loading. Egineers
have to check whether the pile has enough moment capacity to resist the Max. Moment with adequate
factor of safety. If not, the pile may be damaged under the loading.
ALL-PILE Version 6 CivilTech Software www.civiltech.com Licensed to
Depth (Zp) DEFLECTION, yt -cm MOMENT -kN-m SHEAR -kN Pressure -kN/m2 Depth (Zp)
from from
Pile Top-m -5.00 0 +5.00 -1000 0 +1000 -500 0 +500 -100 0 +100 Pile Top-m
0 0
2 2
4 4
6 yt=0 at 6.4-m 6
St=0 at 7.8-m
8 8
10 10
12 12
14 14
16 16
Tip yt=-4.6E-5 Top yt=2.46E+0 Top Moment=-860.0 Top Shear=405.0
Max. yt=2.46E+0 Max. Moment=860.0 Max. Shear=412.5 Max. Pressure=52.08
Top St=1.07E-17
18 18
20 20
22 22
24 24
26 26
28 28
30 30
2 2
4 4
6 6
8 8
10 10
12 12
14 14
16 16
18 18
20 20
22 22
24 24
Lateral Slope Vertical yt Slope Max.
No. Load Restraint Load at Top at Top Moment
26 (kN) (cm/cm) (kN) (cm) (cm/cm) (kN-m) 26
1 40.5 0.0 640.0 0.1 0.00 49.9
2 122.0 0.0 640.0 0.4 0.00 203.0
28 3 202.0 0.0 640.0 0.9 0.00 380.0 28
4 284.0 0.0 640.0 1.5 0.00 569.0
5 324.0 0.0 640.0 1.8 0.00 666.0
30 6 364.0 0.0 640.0 2.1 0.00 762.0 30
7 405.0 0.0 640.0 2.5 0.00 860.0
2 2
4 4
6 6
8 8
10 10
12 12
14 14
16 16
18 18
20 20
22 22
24 24
Lateral Slope Vertical yt Slope Max.
No. Load Restraint Load at Top at Top Moment
26 (kN) (cm/cm) (kN) (cm) (cm/cm) (kN-m) 26
1 40.5 0.0 640.0 0.1 0.00 49.9
2 122.0 0.0 640.0 0.4 0.00 203.0
28 3 202.0 0.0 640.0 0.9 0.00 380.0 28
4 284.0 0.0 640.0 1.5 0.00 569.0
5 324.0 0.0 640.0 1.8 0.00 666.0
30 6 364.0 0.0 640.0 2.1 0.00 762.0 30
7 405.0 0.0 640.0 2.5 0.00 860.0
500 500
450 450
400 400
350 350
300 300
Lateral Load, P -kN
200 200
150 150
100 100
50 50
0 0
0.0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0 0 90 180 270 360 450 540 630 720 810 900
Top Deflection, yt -cm Max. Moment in Single Pile, Mmax -kN-m
300
270
240
210
p, -kN/m
180
150
120
90
60
30
0
0.00 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30 1.40 1.50 1.60 1.70 1.80 1.90 2.00
y, -m
Depth: 2.0, 4.0, 6.0, 8.0, 10.0, 12.0, 14.0 -m
M= 0, P= 405.00 -kN
Results:
At Shear= 405.00-kN, Top Deflection, yt= 11.60000-cm
Stiffness Kpy= 34.91-kN/-cm
At Shear= 405.00-kN, Top Slope, St= -0.03080 Slope
Stiffness Kps= -13149.35-kN/Slope
Or St= -1.76415229 Degree, Stiffness Kps= -229.57-kN/Degree
P= 0, M= 10.00 -kN-m
Results:
At Moment= 10.00-kN, Top Deflection, yt= 0.00977-cm
Stiffness Kmy= 1023.54-kN-m/-cm
At Moment= 10.00-kN, Top Slope, St= -0.00010 Slope
Stiffness Kms= -96153.84-kN-m/Slope
Or St= -0.00595876 Degree, Stiffness Kms= -1678.20-kN-m/Degree
M= 0, P= 405.00 -kN
Results:
At Shear= 405.00-kN, Top Deflection, yt= 2.46000-cm
Stiffness Kpy= 164.63-kN/-cm
At Shear= 405.00-kN, Top Slope, St= 0.00000
Stiffness Kps= N/A
P= 0, M= 10.00 -kN-m
Results:
At Moment= 10.00-kN, Top Deflection, yt= 0.00000-cm
Stiffness Kmy= N/A
At Moment= 10.00-kN, Top Slope, St= 0.00000
Stiffness Kms= N/A
Notes:
Q - Vertical Load at pile top
P - Lateral Shear Load at pile top
M - Moment at pile top
Xall - Pile top total settlement
yt - Pile top deflection
St - Pile top deflection slope (deflection/unit length). Clockwise is negative
Kqx - Secant Stiffness: Vertical load vs. Vertical movement (settlement)
Kpy - Secant Stiffness: Lateral Shear vs. Lateral movement (deflection)
Kps - Secant Stiffness: Lateral Shear vs. Slope (rotation). Clockwise is negative
Kmy - Secant Stiffness: Moment vs. Lateral movement (deflection)
Kms - Secant Stiffness: Moment vs. Slope (rotation). Clockwise is negative
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
ETABS 18.1.1 License #*1VHQUC7UK2NRLHB
Section Properties
d (mm) h0 (mm) dc (mm) Cover (Torsion) (mm)
600 503.7 96.3 65
Material Properties
Ec (MPa) fck (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
25000 25 1 500 500
Notes:
F F
E E
D D
A1.01
C C
B B
A1.01
A A
Sheet Number
NOTES : PROJECT : DRAWING TITLE : Scale :-1: 50, 16, 10
Design By:-
SKJ
1 2 3 4 5 6 7 8 9
1 2 3 4 5 6 7 8 9
F F
E E
D D
C C
B B
A A
Sheet Number
NOTES : PROJECT : DRAWING TITLE : Scale :-1: 50, 16, 10
Design By:-
SKJ
1 2 3 4 5 6 7 8 9