Professional Documents
Culture Documents
3.monitoring System
3.monitoring System
MONITORING SYSTEM
1. CLUSTER
The gauges panel consists of gauges and monitors as shown below, to warn the operator in case
of abnormal machine operation or conditions for the appropriate operation and inspection.
 Gauges : Indicate operating status of the machine.
 Warning lamp : Indicate abnormality of the machine.
 Pilot lamp : Indicate operating status of the machine.
ö The monitor installed on this machine does not entirely guarantee the condition of the
machine. Daily inspection should be performed according to chapter 6, MAINTENANCE.
ö When the monitor provides a warning immediately check the problem, and perform the
required action.
ÿCluster(Machine serial no. ; -#0070)
20 30
10 10 20 40 M MENU
Menu switch
0 0 30
50 BACK Back switch
mph
Km/h
NEXT Next switch
SE
E
L
C
Select switch
7-21
ÿCluster(Machine serial no. ; #0071-)
LCD
mph
Km/h
Select(Enter) key
7707A3CD02
1) SPEEDOMETER
(1) The speedometer displays the speed of machine in mph and
km/h.
77073CD03
7-22
2) FUEL GAUGE
(1) This gauge indicates the amount of fuel in the fuel tank.
(2) Fill the fuel when the indicator moves E point, refuel as soon as
possible to avoid running out of fuel.
ö If the gauge indicates below E point even though the
machine is on the normal condition, check the electric device
7807A3CD04 as that can be caused by the poor connection of electricity or
sensor.
Operating
(3) If the indicator is in the red range, turn OFF the engine, check the
range 7807A3CD05 radiator and engine.
Operating (3) If the indicator is in the red range, it means the transmission is
range 7807A3CD06 overheated. Be careful that the indicator does not move into the
red range.
7-23
6) HYD OIL TEMPERATURE GAUGE
(1) This range indicates the temperature of hydraulic oil.
Red
ÂRed range : Above 105Á C (221Á
F)
(2) Keep idling engine at low speed until the indicator is in the
operating range.
Operating (3) If the indicator is in the red range, reduce the load on the system.
range 7807A3CD08 If the gauge stays in the red range, stop the machine and check
the cause of the problem.
7) WARNING LAMP
(1) When all warning lamp or fault codes are being displayed, this
warning lamp will flash.
(2) When this warning lamp flashes, machine must be checked or
serviced as soon as possible.
77073CD09
77073CD10
7807A3CD11
77073CD12
7-24
11) PARKING BRAKE WARNING LAMP
(1) When the parking brake is actuated, the lamp lights ON.
ö Check the lamp is OFF before driving.
77073CD13
77073CD65
77073CD16
77073CD17
7-25
16) ENGINE OIL PRESSURE WARNING LAMP
(1) This lamp is comes ON after starting the engine because of the
low engine oil pressure.
(2) If the lamp comes ON during engine operation, shut OFF engine
immediately. Check engine oil level.
77073CD18
77073CD20
77073CD21
77073CD22
7-26
21) FUEL LOW LEVEL WARNING LAMP
(1) Fill the fuel immediately when the lamp is turned ON.
77073CD23
7807A3CD24
(2) Emergency
This lamp indicates the emergency steering system is active.
ö Immediately pull the machine to a convenient stop and
stop the engine.
ö The emergency steering system can be manually tested.
77073CD15
Refer to page 7-37-4.
7-27
24) LCD(Machine serial no. ; -#0070)
Cluster 1( ) LCD
1 2( ) MENU
- Display main menu
2
MENU
- Return to the normal display
BACK
3 3( ) BACK
NEXT 4 Return to the previous menu
SELECT
5 4( ) NEXT, BUZZER STOP
Move to the next selection
5( ) SELECT
7807A3CD72
Activate the currently chosen item
1
c
a e 3
2 d
b
6 4
5
7807A3CD93
Forward, reverse, neutral LCD type 1 Display symbol during AEB mode
F, R, N Forward, reverse, neutral LCD type 2 Display symbol during AEB mode
1
1, 2, 3, 4 Actual gear -
P Parking brake mode active -
a Wiper motor intermittently operating -
2 When operating intermittently, it
b -
shows an operating time interval.
c, d Up and down shifting c : Forward, d : Reverse
3 Automatic mode
e Pre-selected gear -
HOUR
7-28
(2) Display map
Normal Main menu Sub menu Activate item
Press MENU Press ACCESSORY Press ACCESSORY
Job timer
ÂPress : Display ON, OFF or RESET
ÂMeasures time in seconds.
Stop watch -
ÂPress : Start. Press again : Stop.
LATEST-DIS
Latest ÂDistance until recent times. Km
Odometer TOTAL-DIS
Total ÂTotal distance. Km
1
ÂAlarm setting. It is possible to set 3 alarms.
Alarm 2
ÂStop alarming :
3
User
ÂRaise the idle rpm to 1200rpm automatically
Alternate idle -
to warm up the engine.
Mode 1 ÂAutomatic travelling speed is applied from 1st
(1st-4th) to 4th gear. -
Auto 1/2
Mode 2 ÂAutomatic travelling speed is applied from
(2nd-4th) 2nd to 4th gear. -
Mode 1 ÂPress button once : Shift down, press button
(Down/Up) again ; shift up. -
Quick
shift Mode 2 ÂPress button every time : Shift to lower gear
(Down) respectively. -
Auto ÂON : Transmission auto condition.
Select ÂOFF : Transmission semi-auto condition.
Aux-sw
Clutch ÂON : Clutch cut-off is activated. -
Cut-off ÂOFF : Clutch cut-off is cancelled.
Cooling fan Forward ÂForward active -
Control Reverse ÂReverse activeø
øReverse mode cleans out quickly dirt and dust on radiator and cooler by reverse rotation of cooling fan.
7-29
Main group Sub group Meaning Display on LCD display
Adjustment Unit ÂChoose between metric and inch unit display.
TOTAL-DIS TOTAL-DIS
Km Mile
Monitor display. C V
ÂPress : Display ON or OFF.
Fault ÂError code display.
-
Code ÂConsult a Hyundai dealer to error code.
Engine
ÂEngine coolant temperature display. COOLANT
Monitor C
ÂPress : Display ON or OFF.
7-30
(3) Machine fault code
When selecting the fault code menu, it shows all of the fault codes which mean abnormal
conditions of present time.
77073CD60
7-31
LCD(Machine serial no. ; #0071-)
1 LCD
2( ) Right, Buzzer stop
Move to the next selection
1
3( ) Select(Enter)
Activate the currently chosen item
2 4( ) Escape
3 Return to the previous menu
4 5( ) Main, Menu
5 - Display menu
7707A3CD04
- Return to the main display
2
TYPE 1 TYPE 2
1
4
c
a
3 e 5
b
d
7
6
8 9
7707A3CD10
7-32
(2) Display map
7707A3CD11
1
ÂAlarm setting. It is possible to set 3 alarms.
Alarm 2
ÂStop alarming :
3
User ON
Alternate ÂRaise the idle rpm to 1200rpm automatically
idle to warm up the engine. -
OFF
Mode 1 ÂAutomatic travelling speed is applied from 1st
(1st-4th) to 4th gear. -
Auto
select Mode 2 ÂAutomatic travelling speed is applied from
(2nd-4th) 2nd to 4th gear. -
Mode 1 ÂPress button once : Shift down, press button
(Down/Up) again ; shift up. -
Quick
shift Mode 2 ÂPress button every time : Shift to lower gear
(Down only) respectively. -
Auto ÂON : Transmission auto condition.
select ÂOFF : Transmission semi-auto condition.
Aux-sw
Clutch ÂON : Clutch cut-off is activated. -
cut-off ÂOFF : Clutch cut-off is cancelled.
Fan Forward ÂForward active
control Reverse ÂReverse activeø
øReverse mode cleans out quickly dirt and dust on radiator and cooler by reverse rotation of cooling fan.
7-33
Main group Sub group Meaning Display on LCD
Adjustment MKS Total 50.7 Km
Unit ÂChoose between metric and inch unit display.
ENG Total 31.5 Mile
Wiper Intermittence ÂWhen using the intermittent function of wiper
motor, it regulates operation time.
Alternate RPM ÂRegulate idle rpm.
ÂPress : Adjust idle rpm increments -
(or decrement) by 25rpm.
Pulse
ÂPress : Modification. -
AEB ÂIt controls the disk interval of the transmission,
automatically.
Model ÂIt is set at the factory, so there's no need to
-
change.
ENG/KOR ÂEnglish : Display in English.
-
ÂKorean : Display in Korean.
Display 1/2 ÂType 1 : Indicate with the symbol.
ÂType 2 : Indicate with a letter. ,
7-34
(3) Machine fault code
When selecting the fault code menu, it shows all of the fault codes which mean abnormal
conditions of present time.
3 's FAULT 71
34 71 72 TCU Communication Error
7707A3CD36
7-35
(4) Transmission warning