Professional Documents
Culture Documents
Omn01ard - Jsa-Installation of Light Sensor at Top of JS and SS Skids
Omn01ard - Jsa-Installation of Light Sensor at Top of JS and SS Skids
I. JSA Information
1. JSA Title: Installation of light sensors at top of SS and JS Skids 2. JSA Location: Base camp/Field
3. JSA No: OMN01ARD47-2022-5-07 4. JSA Page No: 1 Page of
5. Date JSA Conducted: 07-05-2022 6. New Revised
7. Does a SOP already exist for this activity? 8. If yes, then SOP Name / Number:
Yes No
9. Title of Person who routinely does (or will do) the activity the JSA 10. Department of Person in Step 9:
is being conducted for Camp Electricians
11. JSA Conducted by: Reju Abraham 12. Supervisor: Anoop Joshi
2 Place proper ladder (step ladder Slip Trips Falls damage/Injury 1. Ensure all personnel assigned work at
– Aluminium) with sufficient Fall of tools height are not afraid of height and medically
height for the work. Unsafe working conditions fit for work at height.
Hit by the ladder 2. Work shall not be allowed to be carried out
standing over wooden boxes, empty barrels,
and other own arrangements.
3. Ladders with broken rugs shall not be used.
4. Placement of ladder should be in proper
securing position.
ARGAS Classification: General Use
3 One additional person to be Ergonomic hazards, Manual handling, Injuries to hand and 1. Ensure that there is always supervision. Job
appointed to hold the ladder at slip/trip hazards, Pinch points. fingers supervisor shall be present 100% till the job is
down to secure. being completed.
4 Before doing the work Log out Tag Ergonomic hazards, Manual handling, Injuries to hand and 1. Only competent electrical persons shall
out must be carried out (from slip/trip hazards, being hit by moving fingers allow to do the work.
concerned skid and from main DB) objects. Crush injury. 2. Log out Tag out training must be done.
5 The person should attach his lifeline Ergonomic hazards, Manual handling, Injuries to the personnel 1. Suitable hooks must be available at top of
in a secured place at top of the skid, slip/trip hazards, Pinch points. and damage to property the skid to attach the lifeline.
then mark the area and drill holes for 2. Only competent electrical persons shall
fix the light sensor with drill machine. allow to do the work.
3. Wear safety glasses or a face shield (with
safety glasses or goggles).
4. Keep drill air vents clear to maintain
adequate ventilation.
5. Keep drill bits sharp always.
6. Keep all cords clear of the cutting area
during use.
6 Once completed the drill, fix the Ergonomic hazards, Manual handling, Injuries to the personnel 1. Only competent electrical persons shall
sensor at top of the skid, and slip/trip hazards. Hand/finger crushed. and damage to property allow to do the work.
screwed properly. 2. The person holding the ladder from down
should take extreme care during the drill.
7 After completion of job collect all Falling objects Injuries to the personnel 1. Correct tools need to be use.
tools and equipment from the top of Falling from the ladder. and damage to property, 2. Use proper 3 point of contact.
the skid and climb down slowly 3. Tools should not throw from the top.
through the ladder to ground.
8 Remove the ladder from the skid Ergonomic hazards, Manual handling, Injury to the people and 1. Use 2 persons while carrying the ladder to
and place in a secure place in slip/trip hazards, being hit by moving damage to the property the workshop.
the workshop. objects
A. Risk Score Prior to Mitigation: High B. Risk Score Post Mitigation: Medium
C. Risk Tolerable: Yes No D, If No, describe actions:
E. JSA Accepted / Approved by: F. Job Title: Party Chief
ARGAS Classification: General Use
G. Date: H. Comments: