Professional Documents
Culture Documents
HV Lamp
HV Lamp
一、 NOTES
CONTENTS 1. The UV lamp can't direct skin, eyes and other parts of the body in the
process of irradiation。
一、 Notes............................................................................... 2
2. To fasten on irradiation head, use light button or foot switch control
二、 System Working Surroundings..................................... 2
head work。
三、 System Configuration.................................................... 2
3. Are not allowed to budge irradiation head front lens, otherwise it will
四、SYSTEM OPERATION INTERFACE................................... 3
affect the output of uv energy。
1. Operation Interface Diagram......................................... 3
4. Please use dry towel to wipe the equipment。
2. Connection Terminal Diagram....................................... 3
5. Ensure that equipment is maintained in a dry environment。
3. Control Interface DB15 Terminal Definition................. 4
6. The equipment is in a state of irradiation, please don't set parameters。
4. LCD Screen Display Content Annotation....................... 5
7. Power or power outages soon, please don't touch the light head。
5. Instruction of Buttons.................................................... 5
8. When pull out plug plug, please ensure that the equipment switch in
五、 System Installation.........................................................6
the off state。
1. Irradiation head connection.......................................... 6
9. Without permission to remove the equipment, no warranty。
2. Foot switch connection.................................................. 6
10.Wash at least once a week irradiation head, drive outlet, in case of
3. Power connection........................................................... 6
heat dissipation is not good。
六、 Steps of the system operation...................................... 7
二、 SYSTEM WORKING SURROUNDINGS
1. Starting system............................................................... 7
1. Environment temperature:0℃--40℃
2. Irradiation........................................................................ 7
2. Environment humidity:20%--80%
2.1 SYSTEM RUNNING OPERATION..................................... 7
3. Power connection:220VAC
2.2 IRRADIATION PARAMETER SETTINGS.............................. 8
三、 SYSTEM CONFIGURATION
3. System Settings............................................................... 9
3.1 BEEPER SETUP................................................................ 10
Configuration item Model Qty/set
3.2 TEMPERATURE SENSOR SETTING.................................... 10
Controller 1 PCE
4. The total irradiation time query.................................. 11
UV Head 1 PCE
5. Irradiation temperature query.................................... 11
UV Head Connecting 1 PCE
6. System Password Setting............................................. 11
Power line 1 PCE
7. Foot switch control Irradiation.................................... 12
Food Swith 1 PCE
8. SHUTDOWN SYSTEM..........................................................12
Operating Instruction 1
EQUIPMENT WARRANTY............................................................13
1 2
Operating Instruction
LCD
Terminal Terminal
(Down) (Up)
2 3 Common ground 3 NC
time
3 4
Operating Instruction
System Settings password Password Irradiation head interfaces are connected at one end(see Figure 1), and the other
Time Time query Set PW Password Setting end connection controller interface(see Figure 2)
terminal connected to a pedal switch. 4 the terminal connection in the same way, for
5. INSTRUCTION OF BUTTONS
example as follows:
5 6
Operating Instruction
六、STEPS OF THE SYSTEM OPERATION (2)Press any channel button, the system controlled by the set parameters, 4
channel display lamp all in red(See Figure 6),LCD display irradiation time change
1. STARTING SYSTEM (See Figure 8).Irradiation time reaches the set value, the system automatically
Put through power supply, press the controller at the back of the red button(See stop.Indicator light is all green,LCD display by the automatic control of radiation
2. IRRADIATION Among them, the figure 7 M is the abbreviation of "Manual" form, namely manual control,
2.1system running operation "18" for the irradiation time. Figure 8 A is the abbreviation of "AUTO" in the form,namely
After startup, the system to enter the main menu interface(See Figure 4),there the automatic control
are 4 set options for“Work type”、“System”、“Time”、“Temp”,By the direction Simple operation process:
key to select up and down,press“OK”confirm options.The system default options for (1)Manual Control:
“Work type”。 Starting up (see figure 4)→Use the up and down the direction key choose the
(2)Automatic Control:
Starting up (see figure 4)→Using the up and down the direction key choose the
Figure 4 Main menu interface Figure 5 Work type→OK(see figure5)→MULTI(see figure 6,7)→System running→MULTI(see figure5)
After selecting“Work type”option,Press OK button,the system will appear factory →The system stop illuminate
default Settings(See Figure 5),Irradiation power for 100%,Irradiation time for 2.2 Irradiation parameter Settings
20s.Press the "MULTI" or any channel button, system can begin to illuminate. If you want to set the irradiation power and irradiation time, and can be set by
(1)Press the "MULTI", the system is not affected by the set time limit,4 channel the following method.When leaving the factory, the system has carried on the password
display lamp all in red(See Figure 6),LCD display irradiation time change(See Figure Settings,So set parameters for the first time need to enter the password.The initial
7).Press the "MULTI" again, the system will stop,Indicator light is all green,LCD display password is 666666.
initial password→OK→Using the up and down the direction key choose the Work type
→OK→Using the four direction keys set power value→MENU(Power setting has been
completed)→Using the up and down direction keys move the cursor to the time value
7 8
Operating Instruction
If set to "Open", each time you start and end illuminate will have a buzzer beep;
If set to "Close", each time start and end illuminate buzzer will not sing.
No matter what kind of situation is the setting of the buzzer, the LED don't work
Figure 9 Figure 10 properly or irradiation head overheat, buzzer will call the police.
Show in Figure10,P:55% said irradiation power set to 55%;T:55555S said irradiation If detected LED don't work properly, buzzer alarm, interface shown below:
time set to 55555s.Time set range 0~59999s,power set range 0~100%.The system default LED err
time is 20s,power is 90%. At this point, press "MENU" button to return to the main MENU.
After completion of the power set, if found by the power value does not meet the If the operating temperature of the detected radiation head more than set the alarm
requirements, the need to modify, is the first to use the cursor up and down arrow keys temperature,the buzzer will alarm,and the interface shown in figure 13.At this point,
to power value, then press "MENU" key, then the numerical changes.Finally,press‘OK’ press the "OK" or "ECS" button to return to the main menu.
NOTES:
(1)After setup complete,press "ECS" return to the main menu interface(Namely exit
the Settings state, enter the running state),According to the operation specified in
section 2.1 again,The system according to the parameters that are set to run.
(2)When the system is in operation, press the MULTI or any channel button, system Figure 12 Figure 13 Figure 14
will illuminate;If before irradiation, press the MENU key, the system into the setup 3.2 Temperature sensor setting
state, press the MULTI or any channel button at this time, the system does not illuminate. After entering the system Settings interface, select the "Sensor" option,then enter
(3)If the reboot the system, the system will run according to the last set parameters. setup interface of the temperature sensor(see figure14)Using the up and down direction
When need to modify the parameters, it can press the MENU, according to the above method key choose Settings option,press“OK”confirm option.
to set parameters. After selected the "Valid", appear alarm temperature Settings interface ( see
Enter the main menu, select the "System" option, then enter Using the four direction keys set temperature values(setup range 0~75℃)
,press
the interface of System setup(see figure11),it have “OK”button confirm setup,The system will save the Settings.
"Buzzer", "Sensor" 2 Settings,By the up And down direction After setting the alarm temperature, when the controller detected temperature of
key to select,press“OK”button confirm option,The system UV head exceeds the alarm temperature,It will close the illuminate of ongoing process,
default options for“Buzzer”. Figure 11 and after irradiation closed, irradiation head continue air cooling 35s.
setup interface of the buzzer(see figure12)Using the up and down direction key choose
9 10
Operating Instruction
As shown in figure 15 interface:among them,the H said can through the following operations.
hours(the abbreviation of Hour),M said points First of all, according to the connection method of the foot switch connected to
irradiation time,Figure 15 shows the total irradiation Figure 15 Fifth terminal connects the foot switch:after the connection,starting up,Stepped
time is 22 minutes. on the foot switch doesn't loosen,the system began to illuminate;Loosen the pedal swith,
5. IRRADIATION TEMPERATURE QUERY Sixth and seventh terminal connects the foot switch:after the connection,starting
Enter the main menu interface, select “Time” option, up,Stepped on the foot switch,system began to illuminate,To set up after the irradiation
As shown in figure 15 interface.The figure 16 shows time, the system automatically stops.If before have not reached by the irradiation time,
Irradiation temperature is 28.5℃ Figure 16 stepped on the foot switch, the system will also stop illuminate.
6. SYSTEM PASSWORD SETTING Sixth and seventh terminal connects the foot switch:after the connection,starting
At the same time press "ESC",up and down arrow keys ,There will be appear super up,Stepped on the foot switch,system began to illuminate;Stepped on the foot switch,
password is 020928,Press "OK" to enter the interface shown in figure 18,using manual, not affected by the irradiation time and the power of the setup.
‘↑’、‘↓’select“YES”,Press "OK" to enter the password Settings(see figure19), Four pair foot switch control signal, the sixth and seventh signal control effect
Using the direction keys to enter the password,press“OK”confirm setup,The system is equivalent to 1, 2, 3, 4 channel buttons;The eighth signal control effect is equivalent
After the password, if need to set up the system running parameters, need to enter the 8. Shutdown system
password before setting. At this time will be shown in figure 19 interface: Close the controller at the back of the red power switch, unplug the power supply,
closed system.
9. Announcements
1.Irradiation process, cannot use radiation head direct illuminate human skin,
eyes and other parts of the body.
Figure17 Figure 18 Figure 19 2.Fixed irradiation head working position,using the button control irradiation
Simple operation process is as follows: head work.
At the same time press "ESC",up and down arrow keys(see figure17)→enter super 3.Do not allow the budge irradiation head front lens, otherwise it will affect
password→OK(see figure 18)→select “YES”→OK(see figure19)→enter the output of uv energy.
password→OK→setting completed 4.In the case of a power outage, please use dry towel scrubbing equipment.
11 12
Operating Instruction
head. collect fees.Our company only charge cost (including shipping costs or transportation
7.Please clean up once a week irradiation head outlet and drives the dust off costs).
Equipment Warranty
failure under normal use, it is to point to in the normal service condition, with no
not human improper operation, not to the user to remove, repair by the damage caused.
High power LED light source device, since the date of purchase, one year free warranty.
Enjoy lifelong maintenance, more than a year later, to take the paid service, the company
3、Beyond allows the use of the environment (such as high temperature, corrosion, etc.)
lead to damage;
4、Due to abnormal external forces (such as falling, extrusion, knock against, impact,
5、Natural disaster or other force majeure (such as fire, flood, earthquake, lightning,
13 14