Professional Documents
Culture Documents
Npcs Afouad 8kpm Gtca
Npcs Afouad 8kpm Gtca
ENGINEER NAME
A.Fouad
General Inspection:............................................................................................................................................................................................................................2
Electrical system and Control systems.............................................................................................................................................................................................2
Air systems..........................................................................................................................................................................................................................................3
Calibrations sheet...............................................................................................................................................................................................................................4
Data summary....................................................................................................................................................................................................................................5
Data summary (continued)................................................................................................................................................................................................................6
Lube Oil...............................................................................................................................................................................................................................................7
Dry Gas Seal System..........................................................................................................................................................................................................................7
Gas fuel system...................................................................................................................................................................................................................................8
Start Systems & Auxiliary motors....................................................................................................................................................................................................9
Fire and gas system............................................................................................................................................................................................................................9
Performance......................................................................................................................................................................................................................................10
Solonox set-up...................................................................................................................................................................................................................................11
Exchanged pieces..............................................................................................................................................................................................................................11
Alignment check...............................................................................................................................................................................................................................11
Boroscope inspection........................................................................................................................................................................................................................12
Vibration survey...............................................................................................................................................................................................................................14
Conclusions and recommendations................................................................................................................................................................................................16
Air systems.
1. Check air inlet filters for water carry over , pre-filter condition ______
2. Check inlet duct for rust, salt contamination, obstruction ______
3. Perform detergent wash ______
4. Inspect & replace air inlet filters as needed ______
5. If air dryer installed check its operation ______
6. If self-cleaning filters system installed, check supply pressure, manually cycle through cleaning operation ______
7. Inspect engine compressor variable vane mechanism for wear. Check for bent arms, loose linkages,
loose bushings. Ensure stop settings are correct. Check for damaged signal wires to actuator if applicable ______
Caterpillar Confidential: Green Page 3
8. Inspect bleed valve actuator mechanism for proper operation ______
9. Inspect intake and exhaust systems for damage, leaks, debris ______
Calibrations sheet.
Alarm or shutdown switch Customer tag Solar tag Plc address Settings Calibration Remark
Low lube oil pressure
Lube oil filter differential pressure
high
High lube oil pressure
Low oil tank level alarm
Low oil tank level shutdown
High oil tank pressure,AL
High oil tank pressure,SD
Low servo hyd oil pressure, AL
Low servo hyd oil pressure, SD
Low gas fuel pressure
High gas fuel pressure.
Low liquid fuel press (transfer)
High inlet air differential pressure
High start fuel flow
Flameout switch
Servo oil filter ΔP
Lube oil filter ΔP
Alarm or shutdown transmitter Customer tag Solar tag Plc address Settings Calibration Remark
Lube oil pressure
Servo hyd oil pressure
PCD pressure
Gas fuel pressure
Data summary.
System Units Description Cust. tag Solar tag Min Max Alarm Shutdown Before visit After visit
% GP speed
% PT speed
Bar PCD
kW Power
mbard Delta P air filter
ºC T1
ºC T5 average
ºC T5-1
ºC T5-2
ºC T5-3
ºC T5-4
ºC T5-5
ºC T5-6
ºC T5-7
ºC T5-8
Turbine
ºC T5-9
ºC T5-10
ºC T5-11
ºC T5-12
ºC T5-13
ºC T5-14
ºC T5-15
Caterpillar Confidential: Green Page 5
ºC T5-16
ºC T5-17
ºC T5 minimum
ºC T5 avg- T5 min
ºC T5 maximum
ºC T5 max- T5 avg
ºC Cold junction
ma Butterfly valve
ma Pilot gas valve
Actuators ma Secondary valve
ma Guide vanes
ma Bleed valve
System Units Description Cust. tag Solar tag Min Max Alarm Shutdown Before visit After visit
mm/s Accessory drive
μm Bearing 1X
μm Bearing 1Y
μm Bearing 2X
μm Bearing 2Y
Vibration μm Bearing 3X
Turbine μm Bearing 3Y
μm Bearing 4X
μm Bearing 4Y
μm Bearing 5X
μm Bearing 5Y
μm DE bearing X
Vibration μm DE bearing Y
Compressor μm DE bearing X
μm DE bearing Y
ºC Oil tank
Bar Header pressure
ºC Header temperature
Caterpillar Confidential: Green Page 6
ºC GP thrust bearing
ºC GP thrust brg- header
ºC PT thrust bearing
Lube oil ºC PT thrust brg- header
ºC Bearing 1 drain
ºC Brg 1 drain – header
ºC Bearing 2&3 drain
ºC Brg 2&3 drain - header
ºC Bearing 4&5 drain
ºC Brg 4&5 drain –header
1. Inspect fuel control system for security, leaks and proper operation. Include gas fuel control valve, fuel control
Caterpillar Confidential: Green Page 7
actuator ______
3. Remove and inspect fuel injectors for cracks, excessive oxidation or damage ______
4. Check and record T5 spread.
1. Inspect and test pre/post lube oil pump, back-up lube oil pump ______
2. Inspect starter clutch if applicable to ensure lock-up in one direction and free rotation in the other ______
3. Check DAC start system for grounds, insulation, VFD, terminals cleanliness ______
4. Record coast down and start-up timer ______
5. Add grease to electrical motor roller bearings ______
1. Check fire detectors for cleanliness and sensitivity with UV/IR. ______
Caterpillar Confidential: Green Page 8
2. Check proper working of percussion head, strobes and horn ______
3. Check fire bottle for proper charge ______
4. Check sealing of enclosure in case CO2 is released: doors, dampers… ______
5. Check calibration of gas detectors and record value displayed for 50 % LEL sample gas. ______
Performance.
T1 % of minimum speed
Atmospheric pressure % of minimum power
T5 % of minimum PCD
Inlet losses % of minimum T5
Exhaust losses
PCD
Caterpillar Confidential: Green Page 9
Power
T1 % of minimum speed
Atmospheric pressure % of minimum power
T5 % of minimum PCD
Inlet losses % of minimum T5
Exhaust losses
PCD
Power
Solonox set-up.
Bore. Face.
0 0
Boroscope inspection.
Legend: Legend:
Legend: Legend:
Legend: Legend:
Legend: Legend: