Professional Documents
Culture Documents
4516 Curved Stop & 4519 Straight Stop: Please Read Carefully!
4516 Curved Stop & 4519 Straight Stop: Please Read Carefully!
Parts List
Part Desc. . . . . Qty Part Desc. . . . . Qty
4516A Curved Arm. . . . . . . . . 1 WS001 1/4" Washer. . . . . . . . . . 1
or WN001 1/4" Washer. . . . . . . . . . 1
4519A Straight Arm. . . . . . . . . 1 MT012 5/8" Screw. . . . . . . . . . . 1
Identify and verify that you have all the parts listed. Read the WB001 3/16" Washer . . . . . . . . 2
instructions at least once, familiarizing yourself with the parts and 4519B Stop Block. . . . . . . . . . . 1 NUT004 10-24 Nut . . . . . . . . . . . 2
assembly options, before beginning assembly. This stop is designed 4519P Pivot Pin. . . . . . . . . . . . 1 NUT010A Locknut. . . . . . . . . . . . . 1
to be used on the top of our Ultra Track aluminum extrusion. 4519C Cursor . . . . . . . . . . . . . . 1 MA002 10-24 Set Screw. . . . . . 1
5540 Knob. . . . . . . . . . . . . . . . 1 5786 3/32" Allen Wrench . . 1
There are four basic ways to assemble the stop, depending on HB050 1-1/2" hex bolt. . . . . . . 1
whether you want the stop arm on the left or right side of the stop body,
and whether or not you'll be using a 3/4" sub-fence on the Ultra Track.
A: If you're not using a 3/4" sub-fence, mount the B: If you are using a 3/4" sub-fence, the rounded
stop arm to the stop block so the T-slot in face of the stop edge of the stop block (opposite from the T-slot side)
block faces the front of the track. See two Straight Stops should face the front of the track. See two Straight Stops
shown on left in fig. 2 and stop block in fig. 1. shown on right in fig. 2 and stop block in fig. 1.
NUT004
If you're using the stop on our Ultra Track with a 3/4" sub-fence and
F you're using our Ruler Bar too, you'll want to attach the cursor to the 4519C
back of the stop body. Install the two 3/16" washers (WB001) on the 5/8"
screw (MT012), insert the screw thru the hole in the cursor (4519C) and start WB001 x2
a nut (NUT004) on the end of the screw. Slide the nut in the T-slot of the stop
body, adjust the cursor position on the Ruler Bar and tighten the screw.
MT012
1
Attach the assembled Stop to the top of the Ultra OPTIONAL ACCESSORIES
Track by sliding the bolt head in the T-slot of the Ultra The optional 4523 Micro Adjuster attaches to
track. Position where desired and tighten the knob. either stop and allows up to 5/8" of fine adjustment.
The optional 4517 Extension attaches to the Straight
You can read the stop position by sighting along Stop arm and provides support for wide mitered boards, etc.
the outside edge of the stop arm and either a scale on The optional 4824, 4836 & 4848 Ruler Bar attaches
our optional Ruler Bar, or a scale placed on a 3/4" sub- to the back upper T-slot of the Ultra track and provides
fence or the upper front face of the Ultra Track. an adjustable scale for reading the stop position.
5 23
4 ro
ic r
M ste
19 ju
5
4 ft Ad
519
4 ht
Le nt g
Ri nt:
ou ou c e &
5 19 M M n
4 ht 516 b fe ter
g 4 ft Su oin
Ri unt Le nt: P
o
M ou c e &
M n
b fe ter
Su oin
P
45
Ex17 S
te top
ns
io
n