Professional Documents
Culture Documents
Test6-Paper1 2021
Test6-Paper1 2021
17/09/2022
I
TEST6-PAPER1
A 2 T6
1. For the formwork design IS 456-2000 suggested the deviation from specified
dimensions of footing, what is the maximum deviation allowed?
1) 25 mm 2) 50mm 3) 75 mm 4) 60 mm
3. Which of the following type of bond require at least one and half brick thick
wall of brick masonary?
1) English bond 2) Single Flemish bond
3) Double Flemish bond 4) English cross bond
5. The material used for thermal insulation of roof is _________ having thickness
__________ .
1) Double glass, 45 mm
2) Light colour white wash, 25 mm
3) Coconut pitch cement concrete, 25 mm
4) Cavity wall, 75 mm
7. Select the correctly match option of various materials / structures with their
respective slump values.
a) Lime concrete I) 65 mm
b) Arches II) 75 mm to 120 mm
c) Plastic III) 50 mm to 75 mm
d) Normal RCC IV) 90 mm to 100 mm
e) Impermeable work V) 80 mm to 150 mm
Answer Option
. a b c d e
1) IV II V III I
2) III IV I V II
3) III IV I II V
4) V III II I IV
8. __________ is the projecting stone 67 % into wall to prevent over turning and
supporting joist truss.
1) corbel 2) cornice 3) frieze 4) lacing course
9. What are the percentage of tensile strength, shear strength and bending strength
of concrete respectively in comparison to compressive strength of concrete ?
1) 10%, 15%, 20% 2) 20%, 15%, 10%
3) 10%, 20%, 15% 4) 15%, 20%, 10%
10. Thermosetting plastic is permanently hard product due to pressure and heat in
the range of
1) 343oC to 355 oC 2) 125 oC to 175 oC
3) 135 oC to 180 oC 4) 127 oC to 177 oC
12. Fire load, a fire risk criteria to classify occupancies, for a building having an
area of 80m2 with combustible material of 1400 kg having calorific value of
4000 kcal/kg will be
1) 40,000 kcal/m2 2) 60,000 kcal/m2
3) 70,000 kcal/m2 4) 80,000 kcal/m2
13. The shear force and bending moment are zero at the mid length of cantilever
beam, if it carries a
a) A point load at the middle of its length
b) Uniformly distributed load over half length from free end.
c) Uniformly distributed load over half length from fixed support.
d) Concentrated moment at the middle of its length
Answer Option
1) a and b 2) a and c 3) c and d 4) c only
14. A steel rod of cross section area 200 m2 and 1 m long is subjected to a tensile
force of 40 kN. What is the total elongation of the rod ? If modulus of elasticity
of steel is 200 GPa.
1) 0.5 mm 2) 1.0 mm 3) 1.5 mm 4) 2.0 mm
16. Euler bulking load for one end fixed and the other end free with length of
column ‘4 L’ is given by :
2π2 EI 4π2 EI π2 EI π2 EI
1) 2) 3) 4)
L2 L2 0.5 L2 4 L2
18. Euler’s formula for buckling of column does not hold good if slenderness ratio is
________ for M 20 concrete.
1) 90 to 120 2) Greater than 88
3) less than 105 4) Less than 90
20. If a prismatic bar of uniform cross section ‘A’ and length ‘ 2L’ is suspended
from top, then the elongation of bar due to its self-weight only is _________
where, E is modulus of elasticity of bar material and ‘γ’ is the density of bar
γL2 3γL2 γL2 γL2
1) 2) 3) 4)
6E 2E 2E 0.5E
21. What will be the strength of beam ‘B’ having one side horizontal if the strength
of beam ‘A’ having its one diagonal horizontal is 50% ?
1) 91% 2) 20.5% 3) 30.3 % 4) 70.5%
22. A steel bar of 7 mm is heated from 25 oC to 50oC and it is fixed at one end only.
Then the bar will induce
1) Tensile stress 2) Compressive stress
3) depend on temperature difference 4) No stress
23. A simply supported beam PQ of span 10m carries a point load W = 10 kN at ‘R’
such that PR = 7 m and QR = 3 m, maximum deflection occur ______
1) at ‘R’ 2) at centre of span
3) between Q and R 4) None of the above
24. Which of the following statements are incorrect for the frame shown in figure?
ML (L+2h)
a) Vertical deflection at ‘C’ is given by
2EI
ML2
b) Horizontal deflection at ‘C’ is given by
2EI
Mh2
c) Horizontal deflection at point ‘B’ is given by
2EI
Answer Option :
1) a and c 2) a and b 3) b only 4) c only
1) 0 2) 1 3) 2 4) -1
27. A fixed beam AB of length ‘2L’ having constant flexural rigidity EI carries two
loads ‘P’ at its one third length C and D. the maximum positive bending moment
will occur :
PL
1) at C and D and will be equal to
9
2PL
2) between C and D and will be equal to
9
2PL
3) at C and D and will be equal to
9
PL
4) between C and D will be equal to
9
28. Find the magnitude of maximum bending moment for the beam shown in figure.
20 10 8.33 5
1) 2) 3) 4)
EI EI EI EI
30. A two span continuous beam ABC is as shown in figure below. The distribution
factors at joint B for BA and BC respectively are
32. What is the force in member QR of a pin jointed frame as shown below?
1) 7 2) 6 3) 5 4) 4
1) 9 2) 8 3) 7 4) 6
36. A 3 hinged semi-circular arch of radius ‘2R’ with supports at same level carries
𝑊
a concentrated load ‘ ’ at the crown. Assuming uniform flexural rigidity, the
2
38. Find percentage change in thrust when in case of semicircular arch, subjected to
full UDL has i) No Hinge and ii) has hinge.
1) 89% 2) 80% 3) 12% 4) 20%
39. A cable of span 120 m and dip 10m carries a load of 10 kN/m of horizontal span.
The maximum tension in the cable is ________ .
40. For the beam shown in figure, the influence line diagram for moment at ‘A’ is
41. Draw ILD for the beam shown below and find the magnitude of maximum
bending moment at section x-x
L3 L2 8L3 4L2
− −
9EI 6EI 9EI 3EI
1) [ ] 2) [ ]
L2 L 4L2 2L
− −
6EI 3EI 3EI 3EI
8L3 2L2 8L3 4L2
− −
9EI 3EI 3EI 3EI
3) [ ] 4) [ ].
2L2 2L 2L2 2L
− −
3EI 3EI 3EI 3EI
EI 12 −2 EI 10 −2
1) [ ] 2) [ ]
L −2 4 L −2 4
EI 8 −1 EI 7 2
3) [ ] 4) [ ]
L −1 3 L 2 4
44. Find stiffness coefficient K11 for the frame shown in figure
45. Find flexibility coefficient f12 for the beam given as:
Answer Option :
1) a and b 2) b and c 3) a and c 4) b and d
48. In plate girder, fillet weld between flange plate and web plate is design for
1) Vertical shear only 2) Horizontal shear only
3) Vertical and Horizontal shear 4) Vertical or Horizontal shear
51. In case of Non-Industrial structure, maximum deflection of floor beam when the
structure is not susceptible to cracking is
𝐿 L L L
1) 2) 3) 4)
150 180 360 300
52. Distance between purlin on sloping roof depend on which of the following
factors ?
a) Type of roof covering c) Ventilation
b) Type of sloping roof d) Lightening
Answer Option :
1) a and b 2) c and d 3) a, c, d 4) All of the above
55. Strength of transverse fillet weld is how much percentage extra that of
longitudinal fillet weld ?
1) 25% 2) 30% 3) 33% 4) 50%
57. A column cross section 400 mm x 500 mm, 2250 mm long fixed at one end and
hinged at other end. The ratio of practical effective length to the lateral
dimension is
1) 4.5 2) 5 3) 7.5 4) 15
58. According to IS 456:2000, what is the cracking stress for M30 concrete?
1) 3.14 N/mm2 2) 3.5 N/mm2 3) 3.83 N/mm2 4) 4.0 N/mm2
59. For minimum thickness of RCC slab, what is the maximum diameter of main
reinforcement used in the slab, as per IS 456-2000?
1) 10mm 2) 12 mm 3) 16 mm 4) 20 mm
60. For the design of staircase, self-weight of waist slab is calculated as _____ kN.
Where, tread is 25 cm, riser is 15 cm and depth of waist slab is 125 mm (γ concrete
= 25 kN/m3)
1) 15.2 kN 2) 10.8 kN 3) 9.67 kN 4) 3.62 kN
61. What is the effective span of staircase, supported at each end by landing
spanning longitudinally, if the width of landing is 2.7 m, width of starting
passage is 1.5 m and going of the stair is 2.5 m?
1) 4.2 m 2) 4.25 m 3) 4.5 m 4) 4.6 m
62. In case of retaining wall, what is the maximum factor of safety below which
shear key need to be provided?(For static loading)
1) 1 2) 1.25 3) 1.5 4) 2
63. What is the effective span of staircase supported at each end by edge of the
landing slab, which spans parallel, with the risers, if width of the landings is 1.25
m and 2.75 m and going of stair is 2.5 m
1) 4.125 m 2) 4.2 m 3) 4.5 m 4) 4.025 m
64. What is the maximum percentage of steel require for design of flanged beam for
Fe 250 steel & M20 grade concrete ?
1) 0.76% 2) 0.96% 3) 1.27% 4) 1.76%
65. For high yield strength deformed bars of grade Fe 500, the permissible stress in
direct tension and flexure tension shall be _______ in working stress method.
1) 250 MPa 2) 275 MPa 3) 435 MPa 4) 475 MPa
73. The net downward force of prestressed concrete beam subjected to point load
‘2P cos θ’at center with bent tendon is given as :
π π
1) 2P Sin ( − θ) 2) 2P Cos ( − θ)
4 4
74. In which of the following system, conical serrated wedge type of anchorage
drive into female cone?
1) Lee – Mc Call system 2) Gifford Udall system
3) Magnel Blaton system 4) Freyssinet system
75. A post tensioned concrete beam is prestressed by means of cable 100 mm2 area
and stressed such that modulus of elasticity of steel is 210 MPa, then what is the
loss of stress in cable due to shrinkage of concrete as the age of concrete is 98
days at a time of transfer?
1) 4.2 x 10-2 MPa 2) 2.1 x 10-2 MPa
3) 2 x 10-4 MPa 4) 3 x 10-4 MPa
76. At the time of tensioning, after allowing all the losses, final stress should be
more than
1) 85 % 2) 45 % 3) 76% 4) None of the above
77. A system usually adopted in the mass production of pre tensioned precast
element is
1) Freyssinet system 2) Shorer system
3) Long line method 4) Central tube method
79. Independent float of an activity (i,j) is denoted by IF (i,j) The earliest occurrence
times of i and j are denoted by Ei and Ej respectively. The latest occurrence
times of i and j are denoted by Li and Lj respectively. D (i , j) indicates the
duration of the activity .Select correct option giving IF (i , j) :
1) Lj – Ei – D (i ,j) 2) Lj – Ej – D (i ,j)
3) Ej – Li – D (i ,j) 4) Ei – Lj – D (i ,j)
80. A part of quality management system, that indicates the way of preventing
mistake or defect in manufacturing product and avoiding problem when
delivering solution and service is called
1) Quality control 2) Quality of conformance
3) Quality of design 4) Quality Assurance
81. When was the labour welfare fund act to promote labour set up in India?
1) 1958 2) 1965 3) 1966 4) 1970
82. Which of the following equipment is/are used for levelling purpose ?
a) Crawler tractor c) Dragline e) Trencher g) Ditcher
b) Dozer d) Scrapper f ) Grader h) Power Shovel
Answer Options:
1) b, c, d, g 2) a, f, h 3) b, f 4) b, d, f
83. Which of the following help to identify and systematically list various Cause
that cause attribute problem ?
1) Flow chart 2) Travel chart
3) Ishikawa diagram 4) 80 / 20 rule
85. Items of ‘A’ type are identified for a project using ABC analysis Which of the
following statements are true for them?
a) Even rough quantity estimate is sufficient
b) Bulk ordering is preferred
c) Ordering on EOQ basis is not preferred.
d) Periodic review with less monitoring.
Answer option :
1) Only c 2) a, b, d
3) All of the above 4) None of the above
86. Which of the following is not a type of equipment require for hoisting?
1) Pully 2) Chain hoist 3) Dump truck 4) winch
87. Which among the following construction equipment would you recommend for
compaction of low plastic clay?
1) Smooth Wheeled roller 2) Sheep foot rollers
3) Pneumatic roller 4) Vibratory rollers
88. A construction company has annual demand of 400 M.T of steel. The annual
cost of carrying per M.T of steel is Rs. 4000 and the cost to place an order is Rs.
10000. What is the economic order quantity?
1) 50 M.T 2) 70.7 M.T 3) 100 M.T 4) 44.7 M.T
89. Which of the following IS Code represent heater, non electric light etc ?
1) IS 1643 2) IS 1646 3) IS 1647 4) None of the above
90. On repeating bisection method, number of iterations needed for the error of 10-3
is ____________
1) 4 2) 7 3) 10 4) 14
91. The curve in Simpson’s one-third rule, passing through the coordinates of a
parabolic line has a polynomial upto degree ____________ without error.
1) First order 2) Second order 3) Third order 4) Fourth order
92. Select the statement which is not correct for Bolzano method
a) It is based on Intermediate value theorem.
b) It follows linear convergence.
c) It is used for solution of non-linear equation.
d) It falls under category of bracketing that start with two initial guess. Answer
Option :
1) a, b, d 2) only c 3) c and d 4) None of the above
94. A river is 100 m wide and depth of water at different distance from one bank are
given in the table if water flows at the rate of 50m/min. Find quantity of water
flowing per second. Use trapezoidal rule
Distance (m) 0 10 20 30 40 50 60 70 80 90
Depth (m) 2 6 10 12 15 10 8 6 3 0
96. Which of the following method has more suitability than Gauss Elimination
Method ?
1) Gauss Jordan Method 2) Gauss Jacobi Method
3) Factorization Method 4) Any of the above.
1
97. By using Newton Raphson Method find the find root of 4 = x.
√69
98. In middle point method, what is the atmost guess require for 10 number of
iterations?
1) 1 2) log10 2 3) log10 4 4) log2 10
2 𝑑𝑥 1
100. Evaluate ∫1 by using prismoidal rule (Take h = )
𝑥 4