Professional Documents
Culture Documents
Iso 18084 2005
Iso 18084 2005
STANDARD 18084
First edition
2005-10-01
Reference number
ISO 18084:2005(E)
© ISO 2005
ISO 18084:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
Contents Page
Foreword............................................................................................................................................................ iv
1 Scope ..................................................................................................................................................... 1
2 Normative references ........................................................................................................................... 1
3 Nomenclature ........................................................................................................................................ 1
4 Dimensions and tolerances ................................................................................................................. 3
4.1 Punches ................................................................................................................................................. 3
4.1.1 Upper punches...................................................................................................................................... 3
4.1.2 Lower punches...................................................................................................................................... 6
4.2 Dies......................................................................................................................................................... 9
4.3 Positioning of punch with key in relation to machine turret and tablet shape to be
executed .............................................................................................................................................. 11
5 Designation ......................................................................................................................................... 11
5.1 Designation of punches ..................................................................................................................... 11
5.2 Designation of dies............................................................................................................................. 12
6 Marking ................................................................................................................................................ 12
6.1 iTeh STANDARD PREVIEW
Marking of punches ............................................................................................................................ 12
6.2 Marking of dies.................................................................................................................................... 12
7
(standards.iteh.ai)
Material ................................................................................................................................................ 12
Annex A (normative) Detail of punch head....................................................................................................
ISO 18084:2005 13
https://standards.iteh.ai/catalog/standards/sist/e2406be2-489c-468a-8233-
f10b77cab623/iso-18084-2005
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 18084 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 8, Tools for
pressing and moulding.
iTeh STANDARD PREVIEW
(standards.iteh.ai)
ISO 18084:2005
https://standards.iteh.ai/catalog/standards/sist/e2406be2-489c-468a-8233-
f10b77cab623/iso-18084-2005
1 Scope
This International Standard specifies the main dimensions, tolerances and characteristics of punches and dies
for all kinds of tablets.
This International Standard deals with measures that are relevant for the interchangeability of the press
punches between the different tableting machines of various manufacturers.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
iTeh STANDARD PREVIEW
ISO 2768-1:1989, General tolerances — Part 1: Tolerances for linear and angular dimensions without
individual tolerance indications
(standards.iteh.ai)
ISO 18084:2005
3 Nomenclature
https://standards.iteh.ai/catalog/standards/sist/e2406be2-489c-468a-8233-
f10b77cab623/iso-18084-2005
See Figures 1 and 2.
Key
1 upper punch 13 die groove 25 neck-to-head radius
2 lower punch 14 protection radius or shoulder 26 inside head angle
3 die 15 chamfer or radius 27 neck
4 key 16 outer diameter 28 head
5 land 17 tip straight 29 head outer diameter
6 stem (tip to full barrel) 18 relief 30 outside head angle
7 barrel-to-stem chamfer 19 barrel-to-stem radius 31 head flat
8 cup depth 20 working length of the tip 32 key orientation angle
9 tip face 21 overall length 33 upper punch face key position
10 blended land 22 barrel 34 barrel diameter
11 face 23 working length
12 bore 24 barrel-to-neck radius
4.1 Punches
See Figure 3, Table 1 and Annex A for the detail of the punch head.
See Figure 4, Table 1 and Annex A for the detail of the punch head.
Dimensions in millimetres,
surface roughness values in micrometres
General tolerance: ISO 2768-m
Key
1 dust cup place
Dimensions in millimetres,
surface roughness values in micrometres
General tolerance: ISO 2768-m
Key
1 dust cup place