Professional Documents
Culture Documents
Gn5tr SN SNH Add6xblinking Psu
Gn5tr SN SNH Add6xblinking Psu
Gn5tr SN SNH Add6xblinking Psu
Conditions of Use:
(1) Please use this information only for the purpose of performing repair, maintenance and/or configuration services of the Sony products
(hereinafter the “Repair services”) under the service agreement entered into with the Sony group company (hereinafter the “Service
agreement”). Using this information for any purpose other than the purpose described foregoing is forbidden.
(2) Only the Authorized Servicer’s officers, employees or subcontractors (including their officers and employees) whose duties justify a need-to-
know and who have agreed to hold confidential this information (collectively hereinafter the ”Permitted users”) are permitted to access and 9-888-765-02
use this information. To disclose or disseminate to any person other than the Permitted users is forbidden.
(3) Destroy or erase any and all portion of this information promptly in an irrecoverable and secure fashion after achieving the purpose
described in Section (1) above. LCD TV
(4) Do not copy, replicate, reproduce, alter, translate, transmit, sell, lease, or distribute this information in whole or in part without the prior
written permission of the author.
(Notwithstanding foregoing, it is permitted to copy and distribute this information to the Permitted users.)
(5) Please notify immediately any leakage, loss, theft, misappropriation, or other misuse of this information by e-mail to the following address:
somk-gcs-tissnexim-adm@jp.sony.com
(6) In addition to the above, the terms and conditions of the Service agreement shall be applied to using this information.
Sony EMCS (M) Sdn. Bhd., SVPM
Revision of Information:
This information may be changed or updated at any time without any prior notice. Please confirm that this information is up-to-date before
using it. © 2019.03
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
REVISION HISTORY
Version Date Subject
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
MODEL LISTS
THIS SERVICE MANUAL CONTAINS COMMON INFORMATION FOR BELOW REGIONS AND MODELS:
REGION
ASIA AMERICA EUROPE CHINA JAPAN
MODEL
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
TABLE OF CONTENTS
1 SAFETY NOTES 5
3 TROUBLE SHOOTING 18
5 DIAGRAMS 116
Note: Pictures provided in this manual may have difference from actual sets.
4
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
SECTION 1
SAFETY NOTES
1-1. Warnings and Caution Whenever a TV Main board is replaced, the correct TV Model and Serial
1) CAUTION :These servicing instructions are for use by qualified service number must be reinserted into memory.
personnel only. This is a MANDATORY procedure that each service center must apply.
2) To reduce the risk of electric shock, do not perform any servicing other than
Please refer to the chapter of ADJUSTMENT in this service manual to
that contained in the operating instructions unless you are qualified to do so.
find out how to set the model number and serial number in service mode.
3) WARNING!! : An isolation transformer should be used during any service
to avoid possible shock hazard, because of live chassis. The chassis of this
receiver is directly connected to the ac power line. 1-2-1. Caution Handling of LCD Panel
The replaceable fuse could be in the neutral of the mains supply. When When repairing the LCD Panel, make sure you are grounded with a wrist
replacing the fuse, the mains shall be disconnected for de-energize the phase band.
conductors. When repairing the LCD Panel on the wall, the panel must be secured
using the 4 mounting holes on the rear cover.
(*Except AC ADAPTOR, Because it does not carry out replacing an internal
1) Do not press the panel or frame edge to avoid the risk of electric
fuse.) shock.
4) CARRYING THE TV : Be sure to follow these guidelines to protect your
2) Do not scratch or press on the panel with any sharp objects.
property and avoid causing serious injury :
• Carry the TV with an adequate number of people; larger size TVs require 3) Do not leave the module in high temperature or in areas of high
two or more people. humidity for an extended period of time.
• Correct hand placement while carrying the TV is very important for 4) Do not expose the LCD panel to direct sunlight.
safety and to avoid damages. 5) Avoid contact with water. It may cause short circuit within the module.
5) SAFETY-RELATED COMPONENT WARNING!! : Components identified
6) Disconnect the AC power when replacing the backlight (CCFL) or
by shading and ! mark on the exploded views, and in the parts list are critical
for safe operation. Replace these components with Sony parts whose part inverter circuit. (High voltage occurs at the inverter circuit at 650Vrms)
numbers appear as shown in this manual or in supplements published by Sony.
7) Always clean the LCD panel with a soft cloth material.
Circuit adjustments that are critical for safe operation are identified in this
manual. Follow these procedures whenever critical components are replaced 8) Use care when handling the wires or connectors of the inverter circuit.
or improper operation is suspected.
Damaging the wires may cause a short circuit.
6) IMPORTANT REMINDER FOR TV MAINBOARD REPLACEMENT : It
9) Protect the panel from ESD to avoid damaging the electronic circuit
is mandatory for service centers to confirm the TV‘s system information after
(C-MOS).
each repair carried out with Mainboard replacement.
5
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
10) During the repair, DO NOT leave the Power On or Burn-in period for *Do not recommend power-on in the conditions which laid face down the
more than 1 hour while the TV is face down on a cloth. Refer Figure 1 . panel, in repair activity. Refer Figure 1 .
*When transporting by hand, do not put stress on the panel and the frame
Figure 1. around the screen.
Refer to the panel handling chapter of each Service manual,
or the "Transporting" information of the Reference Guide of each model
for how to hold it.
2) OLED Screen
•Although the OLED screen is made with high-precision technology and
99.99% or more of the pixels are effective, black dots may appear or
bright points of light (white, red, blue, or green) may appear constantly on
the OLED screen. This is a structural property of the OLED screen and is
not a malfunction.
•Do not push or scratch the front filter, or place objects on top of this TV
set. The image may be uneven or the OLED screen may be damaged.
•The screen and cabinet get warm when this TV set is in use. This is not
1-2-2. Caution for OLED Panel a malfunction.
1) Handling
3) Precautions to Protect the Screen from Damage
When repairing the TV set, be sure you are grounded by using a wrist band.
Image retention
*Do not press on the panel or frame edge to avoid the risk of electric shock. OLED TV’s are susceptible to image retention (burn-in) due to the
*Do not scratch or press on the panel with any sharp objects. characteristics of the materials used. Image retention may occur if images
*Do not leave the module in high temperatures or in areas of high humidity are displayed in the same location on the screen repeatedly or over
for an extended period of time. extended periods of time. This is not a malfunction of the TV. Avoid
displaying images that may cause image retention.
*Do not expose the panel to direct sunlight.
The following are examples of images that may cause image
*Avoid contact with water. It may cause a short circuit within the module. retention:
*Disconnect the AC power when replacing. •Content with black bars either on the top and bottom and/or the left and
*Always clean the panel with a soft cloth material. right sides of the screen. (for example, Letterboxed, 4:3 screen, Standard
*Use care when handling the wires or connectors. Damaging the wires may definition)
cause a short. •Static images such as photos.
•Video games that might have static content in some part of the screen.
*Protect the panel from ESD to avoid damaging the electronic circuit.
•On-screen menus, program guides, channel logos etc.
•Static content from applications.
•On-screen tickers, such as those used for news and headlines.
6
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
Panel refresh
Panel refresh will automatically run to adjust the uniformity of the TV
screen after it has been in use for long periods of time.
Panel refresh can also be performed manually and should only be used if 1-3. Caution for Board handling
image retention is very noticeable or you see the following message: Symptom : The following problems will occur due to handling of the IC
[Panel refresh did not finish...] mounted on the board
・Solder crack due to substrate handling (stress)
Caution: ・IC breakdown due to static electricity (ESD)
•The Panel refresh function may affect the panel. As a reference, perform
the Panel refresh only once a year, do not perform it more than once a When repairing the TV at the customer‘s home or service station or
year as it may affect the usable life of the panel. Repair of defect board, please pay attention to the handling of the board
•Panel refresh takes about one hour to complete.
•A white line may be displayed on the screen during the Panel refresh, ※Substrate that needs attention for handling
this is not a malfunction of the TV. ・Main Board(B** - Board)
•Panel refresh will only work when the room temperature is between 10 ・Backend Board(D** - Board)
ºC and 40 ºC.
Pixel shift
Automatically moves the image on the screen to prevent image retention.
7
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
ESD cushion/sheet
② Do not hold/push Heat-Sink
Please use a bag containing the board or a special seat
8
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
④Regardless of Good board or Defective board, always put it ⑦Do not hold Heat-Sink when take out or install it..
on ESD cushion/sheet slowly.
9
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
<K*-55/65A9F>
④After take defective board out from TV, put it into ESD bag.
Do not place on floor mat/carpet direct. And, always put it on
ESD cushion
<K*-65Z9F>
1
0
※Caution
ESD wrist-strap to be checked daily.
Use Multi-meter to make sure resistance of ESD wrist-strap is
OK.(R=750K Ohms to 35Mega Ohms)
10
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
11
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
1-7. How to Find a Good Earth Ground The servicing of these boards requires special precautions. It is
1)A cold-water pipe is a guaranteed earth ground; the cover-plate strongly recommended to use Lead Free Solder material in order to
retaining screw on most AC outlet boxes is also at earth ground. guarantee optimal quality of new solder joints.
2)If the retaining screw is to be used as your earth ground, verify that it is
at ground by measuring the resistance between it and a cold-water pipe
with an ohmmeter. The reading should be zero ohms.
3)If a cold-water pipe is not accessible, connect a 60- to 100-watt trouble-
light (not a neon lamp) between the hot side of the receptacle and the
retaining screw. Try both slots, if necessary, to locate the hot side on the
line; the lamp should light at normal brilliance if the screw is at ground
potential (see Figure 3).
12
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
SECTION 2
SELF DIAGNOSTIC FUNCTION
The units in this manual contain a self-diagnostic function. If an error occurs, the Smart Core Red LED will automatically begin to flash.
The number of times the LED flashes translates to a probable source of the problem.
A definition of the Smart Core Red LED flash indicators is listed in the instruction manual for the user’s knowledge and reference.
If an error symptom cannot be reproduced, the remote commander can be used to review the failure occurrence data stored in memory to
reveal past problems and how often these problems occur.
(Supplementary 13
13 information)
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
AUD_ERR_I2C <B> Audio amp I2C communication failure Blue italic: detect at startup sequence only.
<G>: Power supply board,
TEMP_ERR_I2C <B> Temp sensor I2C communication failure <B>: Main board,
<T>: T-con board,
TU_DEMOD_I2C <B/Tu> Tuner & Demodulator I2C communication failure <LD>: LD board,
<Tu>: Tuner board,
FRCTC_ERR <B> FRC device is not finished Initial sequence <A>: Power Adapter,
<P>: Panel module,
EARC_ERR_I2C <B> eARC I2C communication failure <S>: Speaker
(Supplementary 14
14 information)
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
Self Diagnosis
SN
SELF CHECK
Back
<<
002 MAIN POWER 000000000000 000000000000 000000000000 000
003 DC ALERT 000000000000 000000000000 000000000000 000
003 AUD ERR 150101000018 150101000018 150101000018 003
003 TU DEMOD 150101000218 150101000223 150101000105 003
004 LD ERR 000000000000 000000000000 000000000000 000
005 TCON ERR 150101000504 000000000000 000000000000 001
005 P ID ERR 000000000000 000000000000 000000000000 000
005 FRCTC I2C 000000000000 000000000000 000000000000 000
006 BACKLIGHT ERR 000000000000 000000000000 000000000000 000
007 TEMP ERR 150101000200 150101000002 000000000000 002
(Supplementary 15
15 information)
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
Error count
Error Item
Format of error timestamps
YYMMDDhhmmss (in UTC)
Example: SELF CHECK
120823132523 -> Aug 23 2012 13:25:23 UTC
<<
* Only when time is set, an error timestamp
002 MAIN POWER 000000000000 000000000000 000000000000 000
is saved. 003 DC ALERT 000000000000 000000000000 000000000000 000
Smart Core Red LED 003 AUD ERR 150101000018 150101000018 150101000018 003
blinking count 003 TU DEMOD 150101000218 150101000223 150101000105 003
004 LD ERR 000000000000 000000000000 000000000000 000
005 TCON ERR 150101000504 000000000000 000000000000 001
005 P ID ERR 000000000000 000000000000 000000000000 000
Panel Operation Time clear 005 FRCTC I2C 000000000000 000000000000 000000000000 000
<7> -> <0> 006 BACKLIGHT ERR 000000000000 000000000000 000000000000 000
007 TEMP ERR 150101000200 150101000002 000000000000 002
Timestamps and Error Count clear
<8> -> <0>
Total Operation Time and Boot Count clear 00005 00414 00002
<9> -> <0> [Home]Exit
Error Error Error
timestamp for timestamp for timestamp
last recorded second last for 3rd last
•Panel Operation Time is recorded every
error recorded recorded
30 min, but Total Operation Time is recorded every 1 hr. error error
Therefore, the panel op. time might become larger than
the total op. time.
Total Operation Time [hr] – Boot Count – Panel Operation Time [hr]
(Supplementary 16
16 information)
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
Smart Core
Red LED Error Name Retry Permission Times *1 Note
blinking count Number of off/on action for MAIN_POWER
2x MAIN_POWER STDWN_RTRY_LIMIT_MAINPOWER = 1
shutdown is recorded to
STDWN_OFFON_CNT_MAIN_POWER.
DC_ALERT (5V) STDWN_RTRY_LIMIT = 2
3x
AUD_ERR STDWN_RTRY_LIMIT = 2
LD_ERR STDWN_RTRY_LIMIT = 2
4x
BCM_ERR STDWN_RTRY_LIMIT = 2
4KBE_ERR STDWN_RTRY_LIMIT = 2
8x
4KPQ_ERR STDWN_RTRY_LIMIT = 2
(Supplementary 17
17 information)
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
SECTION 3
TROUBLESHOOTING
Triage Chart
Before you make the service call…
1. Confirm the symptom from the customer.
CHASSIS: SN/SNH 43/49
2. Select that symptom from the chart.
3. Bring all the boards and cables listed for that symptom.
4. Follow the troubleshooting charts in the technical guides to isolate the board.
5. Chart Colour Code
RED DOT: Most likely defective part
BLUE TRIANGLE: Secondary possible defective part
BLACK TEXT: Board that may correct the symptom
B* Board
H* Board
Speaker
LD* Board
VBO FFC
Tcon
LCD Panel
18
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
SECTION 3
TROUBLESHOOTING
Triage Chart
Before you make the service call…
1. Confirm the symptom from the customer.
CHASSIS: SN/SNH 55/65/75
2. Select that symptom from the chart.
3. Bring all the boards and cables listed for that symptom.
4. Follow the troubleshooting charts in the technical guides to isolate the board.
5. Chart Colour Code
RED DOT: Most likely defective part
BLUE TRIANGLE: Secondary possible defective part
BLACK TEXT: Board that may correct the symptom
B* Board
H* Board
Speaker
G* Board
VBO FFC
Tcon
LCD Panel
19
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
No No
20
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
CN401 CN401
pin 18/19/20/21
“+12V_MAIN”
21
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
CN400
CN400
pin 11/13
“+12V_MAIN”
22
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
Number of STBY
Error Item Description
LED flashing
23
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
BCX/BCX2
3-time blinking
Check “+5.0V_VBUS” at OK
C431 on B-Board. Audio Error
4.959V < Voltage < 5.285V ?
NG
IC402, etc
(BCX/BCX2 Board)
(Supplementary 24
24 information)
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
BCX2
“+5.0V_VBUS” at
C431
BCX
“+5.0V_VBUS” at
C431
(Supplementary 25
25 information)
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
START
Check fuse no
F1001 Change F1001
Is fuse not opened?
yes
Check Vin no
F1001 Change adaptor
Is voltage > 18V? F1001
yes
END
(Supplementary 26
26 information)
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
START
(AC ON)
yes
yes
Check Vin
F1003 /F1004 Change adaptor
Is voltage > 18V? no
Check TCON_ON
yes Change BCX2
C1024
no board
Is voltage > 3.0V?
Check EN signal
R1060 voltage Check troubleshoot flow 2.1.4
Is voltage >2.5V? Power u-com failure yes
no
yes
END
Check Vcc
C1032 voltage Change IC1001
Is voltage >5.0V? no
yes
(Supplementary 27
27 information)
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
Board: LDK2
C1024
12.5V_TCON IC1001
C1032
F1004
F1003
R1060
(Supplementary 28
28 information)
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
P-on u-com
G-Board or LDK2 #pin10
IC401
P_ON_#2
#pin13
+1.05V_M2_A_2 (IC606), VCC3IO_EMMC
+12V_MAIN R416 #pin16 (IC2002)
12V_MON
ADC port DDC : +12V_LNB (Q409)
R437
OPWRSB
#pin2
ORESETB
GND #pin14
#pin3 DC_OFF_DET SOC Muffin 2 (IC1000)
+19.5V_12.5V #pin8 X_BL_MUTE
R430 #pin11
_MAIN DC_MON
ADC port #pin20 X_SYSTEM_RST
Tuner (CN2800)
R431
GND
(Supplementary 29
29 information)
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
START
no
no Check 12V_MON
Check VDD Check +3.3V_STBY LIne (C400, CN400 #24pin) Check +12V_MAIN Line
CL401 Voltage.
C441 Voltage. And (only for AC-ADP model) (G board or LDK2 board).
Is the voltage >2.6V?
Is the voltage >3.0V? 3.3V_DDCON (IC408)
yes
yes
no
(only for G-board model) no Type Detection Circuit problem. Check DC_OFF_DET
Check TYPE_DET Check TYPE_DET Line (R466, R467, R468). CL412 or P-on ucom #pin3 Change IC401
C437 Voltage. Check Power supply harness is >3.0V?
Is the voltage 2.6±0.2V? (CN400 #15pin,16pin).
yes
yes
no
no Check P_ON_#1
Check OPWRSB SOC CL417 or P-on ucom #pin12 Change IC401
C434 Voltage. Muffin 2 is >3.0V?
Is the voltage 0V? problem
yes
yes
(Supplementary 30
30 information)
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
Previous page
Check P_ON_#2 no
Change IC401
CL415 or P-on ucom #pin13
is >3.0V?
yes
Check P_ON_HL no
CL414 or P-on ucom #pin18 Change IC401
is >3.0V?
yes
Check ORESETB no
Change IC401
CL413 or P-on ucom #pin14
Is the voltage >3.0V?
yes
Check X_SYSTEM_RST
CL413 or P-on ucom #pin20 Change IC401
Is the voltage >3.0V?
yes
yes
END
Ucom IC401 is working OK
(Supplementary 31
31 information)
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
Board IC Ref Voltage supply Output ref. Enable pin Enable source Fuse Vcc ref.
+12V_MAIN (AC-ADP
LDK2 P-on ucom IC401 #pin10
only)
F400/
BCX/BCX2 IC402 +5.0V_VBUS C425 R456 P-on ucom IC401 #pin13 C425
*F406
F402/
BCX/BCX2 IC404 +5V_MAIN C456 R480 P-on ucom IC401 #pin13 C453
*F409
+3.3V_STBY (AC-
R464 F404/
BCX/BCX2 IC408 ADP only) C580 C589 C436
(+19.5V_12.5V_MAIN) *F407
/+3.3V_MAIN
BCX/BCX2 Q407 +3.3V_MAIN Q407 P-on ucom IC401 #pin13 - C448
F403/
BCX/BCX2 IC405 +1.8V_TU C463 IC405 #PIN5 P-on ucom IC401 #pin12 C461
*F408
BCX/BCX2 IC601 +1.5V_DDR C608 C606 R603 (3.3V or 5V) - C602
BCX/BCX2 IC602 +1.05V_M2_STBY C611 IC602 #PIN3 C610 (+3.3V _STBY) - C610
BCX/BCX2 IC603 +1.05V_M2_A_1 C613 IC603 #PIN3 P-on ucom IC401 #pin13 - C612
F600/
BCX/BCX2 IC604 +1.0V_M2 C625 R620 P-on ucom IC401 #pin12 C618
*F601
BCX/BCX2 IC605 +1.05V_M2_ST_ET C631 IC605 #PIN3 M2 IC1000 #AB34 - C630
BCX/BCX2 IC606 +1.05V_M2_A_2 C633 IC606 #PIN3 P-on ucom IC401 #pin13 - C632
VCC3IO_EMMC
BCX/BCX2 IC2002 C2016 IC2002 #PIN3 P-on ucom IC401 #pin13 - C2015
(1.8V)
(Supplementary 32
32 information)
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
yes yes
Check +5V_MAIN DDCON (IC404)
no
Is IC600 mounted?
yes
Check Enable no
IC600 #pin1 Change IC600
Is voltage >2.5V?
yes
Change DDCON
IC601
(Supplementary 33
33 information)
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
START
yes
Change DDCON IC
(Supplementary 34
34 information)
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
START
yes
IC Ref Voltage supply
no Check +3.3V_DDC_OUT
Check Vcc voltage
DDCON (IC408)
IC602 +1.05V_M2_STBY C6xx
or
Is voltage >3V?
+3.3V_STBY (G* board)
IC603 +1.05V_M2_A_1
yes
IC605 +1.05V_M2_ST_ET
Check Enable pin no 2.1.4 No Power U-Com Failure
IC606 +1.05V_M2_A_2 voltage or
Is voltage >3V? Enable source
VCC3IO_EMMC
IC2002
(1.8V) yes
Change LDO IC
(Supplementary 35
35 information)
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
2.2.1 3x Blinking
LED 3x blinking
(Audio Error)
Go to Replace LDK2
Power Off 43/49 Yes
Power off checking board
Check
OK ?
No
Go to Finish
Power On
Power on checking
Check
55/65/75
Replace B-Board
36
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
2.2.1 3x Blinking
Power Off Check
Measure the
Speaker Yes
impedance by
Replace Speaker
multi-meter
Less than 3Ω or
open (broken) ?
(1) B-Board* Yes
No
PVDD-GND short ?
(See next page)
Confirm the speaker
harness Yes
No Replace Speaker Harness
Cut or shorted
to the chassis ?
(2) B-Board* Yes
LDO out short ? No
(See next page)
Return to 2.2.1
No
Replace B-Board*
No
Change Fuse
2.2.1 3x Blinking
LDK2-Board [43/49]
38
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
2.2.1 3x Blinking
BCX-Board [55/65/75]
F3202
Q407 +3.3V_AUDIO
(1) PVDD-GND short check
Measure impedance between PVDD and GND
IC3202 R3242
at capacitor C3262.
If impedance is <100Ω NG
39
39
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
2.2.1 3x Blinking
Power On Check
Power On Check
From 2.2.1
No
Replace
LDK2-Board (43/49) Yes
or
G-Board (55/65/75)
OK ?
No Finish
40
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
No Sound
Without LED 3x
No sound only Yes Go to
Analog RF and Digital RF ? 2.2.5 No Sound Tuner
Yes Select [External Inputs]→
AV receiver is connected
[BRAVIA Sync Settings]→
to HDMI in ?
[BRAVIA Sync Control]→[off] No
No
Yes Go to
No sound only HDMI ?
2.2.6 No Sound HDMI
Yes
[Speakers] setting is Change the setting to
[Audio System] ? [TV Speakers] No
No
Yes
Headphone is connected to
Disconnect the Headphone
HP/Audio Out terminal ?
Replace
LDK2-Board/B-Board
No
No
No
Replace B-Board
Go to
Power Off Check HP/Audio out terminal or Headphone detect
GPIO may be broken
41
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
No Sound Audio
HP/Audio out
[Sound]→ [Headphone]
Headphone Volume Yes
[Headphone/Audio out] Increase Headphone Volume
is set to MIN?
is set to ?
No
Replace B-Board
No
Replace B-Board
42
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
Analog Audio
Input No Sound
Yes Go to
No sound
AV player is connected Yes Check AV cable connected Analog RF and Digital RF? 2.2.5 No Sound Tuner
to Video In? to correct Jack. No sound?
No
No
Yes Go to
Yes No sound only HDMI ? 2.2.6 No Sound HDMI
[Speakers] setting is Change the setting to
[Audio System] ? [TV Speakers]
No
No
No No
Replace B-Board
43
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
No Sound with
normal picture
Yes
Only RF tuner input?
No
44
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
HDMI No Sound
Check Source Source equipment Yes Plug in "Stereo mini jack cable" from TV to for
DVI
equipment output have Analog Audio In Audio transmission and Change “HDMI/DVI Audio
type (Stereo mini jack) ? Source” to Auto or Analog Audio In
HDMI No
Change Source output to "HDMI" mode.
(DVI mode not support Audio)
Check and Reset Source [NG] No Sound Check Sound by [OK] Output Sound Refer to section
equipment Setting other same model TV 2.2.2 No Sound Audio
Escalate to Designer
END
45
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
5-times blinking
NG
Change Change
BCX/BCX2 Panel (T-con)
NG OK
Check OK
Replace G/LD*Board OK
“+12.5V_TCON”**
G/LD* Board broken
on BCX/BCX2
NG
BCX/BCX2 is Panel (T-Con) is
OK broken broken
OK
Replace the Harness
Between G/LD* Board Harness is
and BCX/BCX2 broken
NG
OK
Replace LVDS/ V-By-One FFC
the V-By-One FFC is broken
NG
+12.5V_TCON**
G/LD* Board: G board or LD board OK voltage: 11V-13.5V
NG voltage: anything below 11V
46
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
BCX (4K- 55” / 65” / 75”) BCX2 (2K and 4K- CPH2 43”/49” & SN/SNH 43”/49”)
12.5V_T
CON
check
point +12.5V_TCON
47
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
R3013
F2000
CN2000
F2001
LEDVCC2 LEDVCC1
49
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
6x Blinking
Check BL_ERR No
CN6401 pin 8 Change Main Board Main board broken
Voltage ≥ 3V?
Yes
No
Change PSU PSU broken
6x Blinking?
Yes
Panel broken
TV Business Division 50 50
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
Pin 8: BL_ERR
TV Business Division 51 51
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
No Picture
NG NG OK
Got Any Normal Check Smart Core Replace
Replace Replace TCON board
Display? (Horizontal/ LED Indication the V by One FFC
the main Board TCON Board NG
Vertical line) No (5x Blinking) No Harness
Yes Yes OK OK
V by One FFC NG
Check Other Refer 5x Blinking Main board NG
Harness NG
Portion: Troubleshooting manual
52
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
NG
Check RF source cable
Change RF cable and antenna
and antenna, OK?
OK
OK
53
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
Digital
Terrestrial Satellite
/Cable
NG
Check Tuner power line 12V LNB Voltage
12V at JL2822 = 12V? Checking
OK
54
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
(Back View)
For Tuner Power Lines
FB280
3
55
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
(Back View)
For Tuner Power Lines
JL2800 =
3.3V
JL2801 = JL2822 =
1.8V 12V
JL2807 =
3.3V
56
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
(Top View)
For Tuner I2C line
C2803
R2802
R2806
R2805
C2804
R2804
R2801
57
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
OK OK OK MOSFET
Check LNB power line Check POWER_ON signal line
Check fuse F2800/F2801* Q408/Q409
+12V_MAIN at R495 = 12V? at R446 = 3.3V?
broken
NG NG NG
G-board
OK
58
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
(Top View)
12V LNB Voltage line
R446
Q408
R495
(Back View)
12V LNB Voltage line
Q40
9
F2800
F2801
59
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
OK
OK
60
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
Digital Tuning 1
Notes: for all tuners except JP-ISDB
- Parts for IFOUT_N line : FB2801, C2807, C2826
For TW-DVB and LA-ISDB - Parts for IFOUT_P line : FB2802, C2808, C2825
- Parts for IFAGC line : R2838, C2827
For AM-ATSC
NG
Confirm ANT or Cable connection A A : Insert correct signal in correct terminal.
OK
Sound is normal?
No sound
Check IC1000 (SoC)
NG
Check SoC(IC1000) and Tuner module
Check Tuner module connection (BCX2)
Change NG parts
61
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
(Top View)
IFOUT & IFAGC line
R2838 C2827
C2807 FB2801
C2808
FB2802
C2825 C2826
62
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
Digital Tuning 2
Cable OK
Sound is normal?
No sound
Refer to Digital Tuning 1
Check IC1000 (SoC) Notes:
On Service - Parts for TU1_TS_DATA0 line : R2847.
CASE B - Parts for TU1_TS_CLK line : R2844, R2815,R2866
mode display
TS_LOCK ? - Parts for TU1_TS_VALID line : R2845.
- Parts for TU1_TS_SYNC line : R2846.
UEC ?
- CASE A : TS _LOCK = LOCK and UEC constant
CASE A - CASE B : TS _LOCK = UNLOCK or UEC is increasing
Change Tuner module
(Refer to Note tuner )
A : Insert correct signal in correct terminal.
Check part mounting condition for digital data line
OK
“TU1_TS_DATA0, TU1_TS_CLK,
TU1_TS_VALID, TU1_TS_SYNC”
NG
Check IC1000 (SoC)
Change NG parts
63
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
(Top View)
TS1 line
R2845
R2844
R2847
R2846
R2815
64
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
[NG] No picture
[NG] No picture
[NG] Connector abnormal [OK] Picture recovered
Physical appearance check HDMI Connector Broken.
On HDMI connector Replace & Re-verify
[NG] No picture
[NG] No picture
65
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
END
66
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
HDCP
Failure Analysis
END
67
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
+5V Power
Failure Analysis
[NG] Impedance ≠ 0Ω
END
68
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
I2C
Failure Analysis
Check impedance of
[OK] Impedance≈ 47kΩ
Check I2C GPIO Line [OK] Impedance ≈ 56kΩ ±5%
Resistor during AC OFF impedance to Ground
RB3603(HDMI1), RB3604(HDMI2) during AC OFF
RB3601(HDMI3), RB3602(HDMI4) HDMI Connector : Pin15&16
END
69
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
TMDS
Failure Analysis
[NG] No Picture
Replace Broken
Resistor and Re-verify Replace B-Board
and Re-Verify
[OK] Picture recovered
END
70
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
Pin 19
R3601 R3661
Pin 1 Pin 19 Pin 1 Pin 19
R3660
RB3611
L3615
RB3612
L3616 L3619
Pin 1 L3618 L3617 L3620 RB3609
RB3610
RB3607
R3658 R3659 RB3608
Pin 19
RB3605
RB3604
RB3606
L3613
L3614
Pin 1
71
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
Video (Rear)
L36:CVBS3P
Composite
CVBS3P
G16:GPIO66
VIDEO2_DET
M2
IC1000
72
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
Video
No Picture
NG (Vpp: 0 V)
Check wave between ** Check condition of parts NG
[VD2621/R2610/
C2633 and IC1000
C2606/R2611]
OK (Vpp: 1 V) OK
73
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
Video
No Picture
OK (Vpp: 1 V) OK
74
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
55/65/75 : BCX
AT35:GPIO56
VIDEO_DET
Video/Component
(Rear)
N35:SOY0
SCART_FB/COMP_Y
M35:CVBS2P
CVBS2P
Component/Composite
M38:Y0P
SCART_SB/COMP_Y
L38:PB0P M2
SCART_SG/COMP_PB
SCART_SR/COMP_PR
L37:PR0P IC1000
A16:SD_CLK
CR_DET
75
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
Component
No Picture Video
No Picture
NG NG (Vpp: 0 V)
Check if input OSD
is GREY OUT
* Check J2600 Connector, Check if input OSD NG * Check J2600 OK (Vpp: 3.3 V)
CR_DET at R2650 Connection,
OK if it is highlighted is GREY OUT
VIDEO_DET
OK if it is highlighted At R2626
Y : 1V OK
OK (Vpp: 3.3 V)
OK NG (Vpp: 0 V)
NG (Vpp: 0 V)
Check VIDEO_DET signal
Path at R2626
Pb : 0.7V
OK (Vpp: 3.3 V)
OK
Muffin [IC1000] J2600 Connectivity J2600 Connector Muffin [IC1000] J2600 Connector J2600 Connectivity
Parts Broken Problem Problem Parts Broken
Problem Problem Problem Problem
76
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
43/49 : BCX2
CR_DET
A16:SD_CLK
L38:PB0P
SCART_SG/COMP_PB
Video/Component L37:PR0P
SCART_SR/COMP_PR
(Rear)
PbPr
M35:CVBS2P
CVBS2P
M38:Y0P
Composite/Y
SCART_SB/COMP_Y
N35:SOY0
M2
SCART_FB/COMP_Y
IC1000
AT35:GPIO56
VIDEO_DET
77
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
Component
No Picture Video
No Picture
OK (Vpp: 3.3 V)
** Check condition of parts:
Y0P : [VD2620/D2601/R2606/
C2603/R2604] NG Check wave NG (Vpp: 0 V) ** Check condition of parts NG
Check wave between NG PB0P : [VD2622/R2603/C2601/ between C2611/R2653 [D2601/VD2620/R2606/
(Y:C2602/C2627), (Pb:C2605), R2607]
(Pr:C2607)and IC1000 and IC1000 C2603/R2619]
PR0P : [VD2621/R2610/C2606/
R2611]
OK (Vpp: 1 V) OK
S0Y : [R2642]
Pr : 0.7V OK
OK
Muffin [IC1000] J2600 Connectivity J2600/J2601 Muffin [IC1000] J2600 Connector J2600 Connectivity
Parts Broken Problem Problem Parts Broken
Problem Problem Connector Problem Problem
78
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
Muffin
Refer to IC troubleshooting for further
[IC1000]
Problem
investigation
J2600/J2601
Connector
Problem
Change Connector
J2600
Connectivity
Problem
79
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
80
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
R2626 Details
R2650 R2626 R2653 VD2621
VD2620
VD2621
VD2622
81
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
82
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
VD2620
R2662
VD2622 R2650
83
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
Non-Detect Detect
Destination Input Signal
(Typical) (Typical)
VIDEO2_DET
WW (Except 0V 3.3V
Video IC1000 G16-GPIO66
UC)
VIDEO_DET
Video / 0V 3.3V
IC1000 AT35-GPIO56
UC Only Component
CR_DET
0V 3.3V
IC1000 A16-SD_CLK
WW UC Only
Video Video / Component
Component/Composite
Composite
84
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
Non-Detect Detect
Destination Input Signal
(Typical) (Typical)
VIDEO2_DET
WW (Except 0V 3.3V
Video IC1000 G16-GPIO66
UC)
VIDEO_DET
Video / 0V 3.3V
IC1000 AT35-GPIO56
UC Only Component
CR_DET
0V 3.3V
IC1000 A16-SD_CLK
WW UC Only
Video Video / Component
PbPr
Composite
Composite/Y
85
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
[Network Set-up]
>[Wired Set-up]
on the TV
B Board
CHK1 CHK2 CHK3 CHK4
Any scratches NO Check Ethernet OK Check OK Check CMF OK
along Connector pins Pulse Transformer IC1000 problem.
Soldering
TX+/-, RX+/- Soldering soldering Change B-board
L3400
lines? J3400 T3400,T3401
YES NG NG NG
Change
Change B-board Change Pulse Trans Change CMF
Ethernet Connector
86
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
CHK1
TX+/-
RX+/-
CHK4
L3400
BCX CHK3
T3401 T3400
CHK2
J3400
87
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
CHK1
TX+/-
RX+/-
CHK4
L3400
BCX2 CHK3
T3401 T3400
CHK2
J3400
88
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
Yes Yes
NG
*1 Hardware defect suspected. Check with another Wi-Fi
Access Point
Go to the next page module
OK
WiFi module
89
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
Check harness
NG OK
connection is OK Connect properly Loose harness
between Wi-Fi and
BCX/BCX2
OK NG
OK
OK If Wi-Fi malfunction happens,
・Wi-Fi module
Wi-Fi module Main Harness ・Harness between WiFi and BCX/BCX2
・BCX/BCX2 board
are suspected.
90
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
Please refer
Home > Settings > OK Check BT antenna OK Voice Remote manual
Bluetooth Settings Connection is OK Or
Can read
Near discoverable Bluetooth Speaker/Headphone/Headset operation manual
Bluetooth Device
NG NG
else
OK
Loose BT antenna
Connect properly connection
NG
Check harness NG OK
connection is OK Connect properly Loose harness
between BT and BCX/BCX2
OK
NG
NG Change harness NG
Change BT module Change BCX/BCX2
Between BCX/BCX2
board
Board and BT
OK OK
91
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
START
Do a Factory Setting
OK
Confirm USB Detection OK?
NG
NG No 5V
Check 5V at JL3420
Picture and Sound OK
(USB port1)
Have 5V but No detection
OK NG
* Confirm USB file
format
OK Change to supported USB format
Sound NG
Sound OK Main IC (IC1000) problem
OK
Change B-Board
END
92
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
START
Do a Factory Setting
OK
Confirm USB Detection OK?
NG
NG No 5V
Check 5V at JL3420
Picture and Sound OK
(USB port1)
Have 5V but No detection
OK NG
* Confirm USB file
format
OK Change to supported USB format
Sound NG
Sound OK Main IC (IC1000) problem
OK
Change B-Board
END
93
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
START
Do a Factory Setting
OK
Confirm USB Detection OK?
NG
NG No 5V
Check 5V at JL3422
Picture and Sound OK
(USB port3)
Have 5V but No detection
OK NG
* Confirm USB file
format
OK Change to supported USB format
Sound NG
Sound OK Main IC (IC1000) problem
OK
Change B-Board
END
94
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
USB 1 port
JL3420
USB 2 port
JL3424
95
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
USB 1 port
JL3420
USB 2 port
JL3424
BCX2
USB 3 port
JL3422
96
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
Valid key No
Check service menu for
CI+ Credentials CI+ Key
Check any pin on No
Invalid key CI Slot is bend or
broken.
Insert CICAM and Yes
Yes
Check CI 5V
at PIN 17/18/51/52
Invalid Key *2 Insert CICAM and Yes
Change B Board Connector CN2200 NG No Check CI Detection
Change B Board at Pin 36/67
No Yes
IC2200 NG *3 Check Resistor
Change B Board Part mounting
END
97
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
1 6 8
2 7
BCX
4 5
3
Ref. No. Location Ref. No. Location Card Detect CI 5V Card Detect
RB2205 1 RB2215 6 PIN: PIN: 17/18/51/52 PIN:
RB2206 2 R2200 7 67 36
RB2209 3 R2203 8
RB2210 4 R2204 9
RB7011 5
98
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
1 6 8
2 7
BCX2
4 5
3
Ref. No. Location Ref. No. Location Card Detect CI 5V Card Detect
RB2205 1 RB2215 6 PIN: PIN: 17/18/51/52 PIN:
RB2206 2 R2200 7 67 36
RB2209 3 R2203 8
RB2210 4 R2204 9
RB7011 5
99
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
OK OK
Connection Results Connection Results
END
Cable Connection Test
Failed Failed
OK
Check cable B board
NG
IR Blaster Cable
B Board
CHK1 CHK2 CHK3
Detection OK, OK OK OK
JL3001 & JL3002, Press ENTER key,
JL3000, pull-down? END
Pull up? JL3003, have pulse?
NO NO NO
Change B-board
100
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
CHK1
JL3000 CHK2
CHK2
JL3001
JL3001
JL3002
JL3002
BCX
CHK3
CHK3
JL3003
JL3003
101
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
BCX2
CHK3
JL3003
102
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
Check harness
OK
connection between Harness connection
Side key buttons error
B-board and switch issue
module
NG
Change harness
OK
between B-board to B-board to switch module
switch module harness issue
harness
NG
OK
Change switch
Switch module issue
module
NG
NG
Resistor value Check resistor value
Parts issue
on B-board
[BCX/BCX2]
R1108 : 0 [ohm] OK In case that power key error
R1049 : 47k [ohm]
R1222 : 4.7k [ohm]
NG
Check resistor value
on B-board
Resistor value
In case that buttons error except power key
[BCX/BCX2]
R1028 : 4.7k [ohm] OK
R1107 : 0 [ohm] Main device issue
R1050 : 20k [ohm] Change B-board
R1051: 22k [ohm]
103
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
Check harness
OK
connection between Harness connection
B-board and issue
SmartCore
NG
Change harness OK
B-board to SmartCore harness
between B-board to
issue
SmartCore harness
NG
OK
Change SmartCore SmartCore issue
NG
OK
Check resistor value
Parts issue
on B-board
Resistor value
[BCX/BCX2] NG
R1110 : 0 [ohm]
R1259 : 47k [ohm] Change B-board
R1217 : 4.7k [ohm] Main device issue
* R1110 may be not mounted
104
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
OK
Change SmartCore SmartCore issue
NG
OK
Check resistor value
Parts issue
on B-board
Resistor value
[BCX/BCX2]
R1109 : 0 [ohm] NG
R1052 : 150k [ohm]
* R1109 may be not mounted Change B-board
Main device issue
105
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
SECTION 4
SERVICE ADJUSTMENT
When finished the operation of service mode , please AC Plug OFF/ON the TV set
*If you don’t do AC plug OFF/ON, remain the Service Mode App and user can see the Service Mode after RC ON.
4
Service Mode
Model Information >>
Self diagnosis History >>
1 Video / Audio >>
Panel / PQ >>
General Setting >>
Tuner >>
2 Wifi/ BT >>
(Supplementary 106
106 information)
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
1) In Service Mode, select “Model Information”, press “Enter” or → button to enter Status Information
Main Micro
Service Mode Model SW Version: PKG2.011.0010NAB
NVM Version: 0001 UC2
Model Information >> Boot Version: V1.000
Self diagnosis History >> Status Information >> PQ Version: 102100006
AQ Version: AQ1.100
Video / Audio >> Model Information >> <Ext>
exFRC: 00.00.00.00
Panel / PQ >> Model Number Setting >>
CameraVID: 0
General Setting >> SERIAL NUMBER EDIT CameraPIC: 0
CameraFW: 0
Tuner >> 4k BE
MLFW: SF1.002
Wifi /BT >> MAFW: SF0.360
SDB Service Menu >> ADSP SF0.501
NDAT SD0.370
PDAT SD0.370
BDAT SD1.011
BCM SD-------
FDAT SD0.002
[</>] Set [Home]Exit UDAT SD0.000
[</>] Set [Home]Exit BDIX SD0.370
107
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
data correct
• Serial Number can be set ONLY ONCE
5) Press “→” or “←” button to select YES
Service Mode
or NO. Select YES if input data is >>
Status Information >>
correct. Select NO if input data is Model Information >>
Model Number Setting >>
incorrect. Press <Enter> to save Serial Number Edit 9 9 9 9 9 9 9
108
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
Service Mode
into EEPROM. SERIAL NUMBER EDIT is Model Number Setting <[ KDL-40X500B
>> ]>
grayed out and the serial number that has Serial Number Edit 9999999
that has been input is displayed. User can Model Information >>
109
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
button
3) Press “↑” or “↓” arrow key to scroll Product
[</>] Set [Home]Exit
Name Candidate.
(e.g. KDL-40X500B CO1,KDL-40X500C
BR6) [MODEL_NUMBER_SETTING]
110
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
4.6 WB Adjustment
Panel / PQ
b.
Back <<
WB Adjustment >>
WB/Mura/CUC data transfer >>
c.
[</>] Set [Home]Exit
Back <<
R WB Gain <[ 0 ]>
Service Mode G WB Gain <[ 0 ]>
a. B WB Gain <[ 0 ]>
Model Information >>
R WB Offset <[ 0 ]>
Self Diagnosis History >>
G WB Offset <[ 0 ]>
Video/Audio >>
>>
B WB Offset <[ 0 ]>
Panel/PQ
General Setting >>
Tuner >>
111
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
Back <<
WB/Gamma data transfer <[ 0. SoC to T-con ]>
Mura data transfer <[ 0. SoC to T-con ]>
Panel / PQ
CUC data transfer <[ 0. SoC to T-con ]>
Back <<
WB Adjustment >> [Start]
WB/Mura/CUC data transfer >>
4) Result OK or NG will be
displayed after performance of
HDD is checked
113
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
2) Select “AAA” by pressing “↑” or “↓” [</>] Set [Home]Exit [</>] Set [Home]Exit
then pressing “Enter” or “→” button to
enter inside. HDD Re-Register
114
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
[Home]Exit
115
SYS SET
2022/09/22 04:50:40 (GMT+09:00)
SECTION 5
DIAGRAMS
* depend on
destinations. Video signal RGBW LEDs Center Key
Audio signal
Light Sens. L/R Keys
Control Bus
IR Rx
* IR In
BCX2 board Panel
* BCAS/CI Flash
Power Micro
Vx1 8-lane MEMC/Tcon
* RF eMMC (STM8S103F2U6) 4K/60p (NT71953)
3G(IC1000)
I2C
2-ch
USB3.0
I2S
SP
SP
USB2.0
Temp Sensor
(I2C)
Ethernet
S/PDIF
Optical S/PDIF
Out
HP/Line Out WiFi/BT
IRB Micro UART
USB HS (J20H088.00)
* IR Blaster (S3F80P5X9R)
* RS232C UART
(Supplementary 116
information) SYS SET
2022/09/22 04:50:40 (GMT+09:00)
SECTION 5
DIAGRAMS
* depend on
destinations. Video signal RGBW LEDs Center Key
Audio signal
Light Sens. L/R Keys
Control Bus
IR Rx
* IR In
BCX board Panel
* BCAS/CI Flash
Power Micro
Vx1 8-lane MEMC/Tcon
* RF eMMC (STM8S103F2U6) 4K/60p (NT71953)
* RS232C UART
(Supplementary 117
information) SYS SET
3 key Source
CN3800 To B-board T-con To source board
CN203
BCX2
BAX_FBoard
GND 1 51 GND T-con Board From T-con board Board
1-474-647-12 HUS_GND 1 15 #30 VBTX7P 2 50 RxP7 Board
HUS_KEY_AD 2 12 #30 VBTX7N 3 49 RxN7
HUS_POWER_KEY 3 14 #30 GND 4 48 GND
1-822-693-11 1-821-900-11 VBTX6P 5 47 RxP6 PANEL 60P FFC FFC 60P
JAM SZ15-03WLR SZ15-03HGR VBTX6N 6 46 RxN6 PANEL 60P FFC
GND 7 45 GND
8
SN/SNH 43’/49’
VBTX5P 44 RxP5
VBTX5N 9 43 RxN5
GND 10 42 GND Hirose: TF06L-60S-0.5SH
VBTX4P 11 41 RxP4 LSM: GF05G-60S-MB-E2000 Hirose: TF06L-60S-0.5SH
CN1000 VBTX4N 12 40 RxN4 Yeonho: 05002HR-H60Y LSM: GF05G-60S-MB-E2000
2022/09/22 04:50:40 (GMT+09:00)
BT
Antena
J110
GND Ground 1
PSJ
LDK2Board
Board GND Ground 2
PWR Power V12 IN 3
PWR Power V12 IN 4
PWR Power V12 IN 5
CN3001 CN401 1-822-322-11
1-844-642-11 1-844-642-11 JST SM05B-PASS-TBT(LF)(SN)
MOLEX 41pin MOLEX 41pin
RGATE2 41 1 RGATE2
GND/CUR_MON 40 2 GND/CUR_MON
PWM0(BLINKING) 39 3 PWM0(BLINKING)
IP_REF(DC_DIMMER) 38 4 IP_REF(DC_DIMMER)
FB_REF 37 5 FB_REF
BL_ERR 36 6 BL_ERR
MAIN_PWR(POWERON) 35 7 MAIN_PWR(POWERON)
BL_ON/ICSPCLK 34 8 BL_ON/ICSPCLK
TCON_ON 33 9 TCON_ON
NC 32 10 NC
REG_19V 31 11 REG_19V
REG_19V 30 12 REG_19V
REG_19V 29 13 REG_19V
REG_19V 28 14 REG_19V
REG_19V 27 15 REG_19V
REG_19V 26 16 REG_19V
GND 25 17 GND
REG_12V 24 18 REG_12V
REG_12V 23 19 REG_12V
REG_12V 22 FFC 41 pins 20 REG_12V
REG_12V 21 21 REG_12V
TCON_VCC12V 20 22 TCON_VCC12V
TCON_VCC12V 19 23 TCON_VCC12V
TCON_VCC12V 18 24 TCON_VCC12V
TCON_VCC12V 17 25 TCON_VCC12V
TCON_VCC12V 16 26 TCON_VCC12V
GND 15 27 GND
X_DAMP_MUTE 14 28 X_DAMP_MUTE
X_DAMP_RESET 13 29 X_DAMP_RESET
X_AMP_ERR_DET 12 30 X_AMP_ERR_DET
SDATA0 11 31 SDATA0
GND 10 32 GND
LRCLK 9 33 LRCLK
GND 8 34 GND
BCLK 7 35 BCLK
GND 6 36 GND
SDATA1 5 37 SDATA1
GND 4 38 GND
MCLK 3 39 MCLK
+3.3V_AUDIO 2 40 +3.3V_AUDIO
RGATE1 1 41 RGATE1
J1000
1-843-369-13
19.5V 1 AC
0V 2
NC 3 Adapter
Header: 104127-0620 (MOLEX)
Housing: 104128-0610 (MOLEX)
CN2000 3 A1 LED1
1-820-294-11 4 A2 LED2
LED_VCC1a 1 A3 AWG30 1 A3 VCC1a
LS Bar A
LED_VCC1b 2 A4 2 A4 VCC1b
LED1 3 A1 5 A5 LED3
LED2 4 A2 6 A6 LED4
LED3 5 A5
LED4 6 A6 Header: 104127-0620 (MOLEX)
LED5 7 NC Housing: 104128-0610 (MOLEX)
LED7 8 B1 8 B1 LED5
LED8 9 B2 9 B2 LED6
LED9 10 B5 14 B3 VCC2a
LS Bar B
LED10 11 B6 15 B4 VCC2b
LED11 12 NC 10 B5 LED7
LED12 13 NC 11 B6 LED8
LED_VCC2a 14 B3
LED_VCC2b 15 B4
CN4002
1-842-566-12
L+ 1 1
L- 2 2
R+ 3 1
R- 4 2
1-842-593-11
PBVP04V-S
1-535-807-31
JST SPS-01T-187*
SPEAKER L+ 1 1 #24
Front L- 2 2 #24
Lch 1-780-577-11
JST WSPS-01T-110B*
1-535-807-31
JST SPS-01T-187*
SPEAKER R+ 1 3 #24
Front R- 2 4 #24
Rch 1-780-577-11
JST WSPS-01T-110B*
118
SYS SET
3 key Source
BAX_F CN3800 To B-board To source board
CN203
BCX Board GND 1 51 GND T-con Board From T-con board Board
1-474-647-12 HUS_GND 1 15 #30 VBTX7P 2 50 RxP7
HUS_KEY_AD 2 12 #30 VBTX7N 3 49 RxN7
HUS_POWER_KEY 3 14 #30 GND 4 48 GND
1-822-693-11 1-821-900-11 VBTX6P 5 47 RxP6 PANEL 68P FFC FFC 68P
JAM SZ15-03WLR SZ15-03HGR VBTX6N 6 46 RxN6 PANEL 68P FFC
GND 7 45 GND
VBTX5P 8 44 RxP5
VBTX5N 9 43 RxN5
GND 10 42 GND Deren: 0.5pitch 68pin 1.8H FPC
VBTX4P 11 41 RxP4 Deren: 0.5pitch 68pin 1.8H FPC
CN1000 VBTX4N 12 40 RxN4
7 1 WIFI_STBY_3.3V GND 13 39 GND
14 2 X_WIFI_BT_RST VBTX3P 14 38 RxP3
1 3 SC_STBY_3.3V VBTX3N 15 37 RxN3
13 4 X_WIFI_WAKEUP GND 16 36 GND
SN/SNH 55’
15 5 WIFI_GND VBTX2P 17 35 RxP2
12 6 X_BT_WAKEUP VBTX2N 18 34 RxN2
9 7 WIFI_GND GND 19 33 GND
Main Harness NC 8 3D_LR VBTX1P 20 32 RxP1
8 9 WIFI_GND VBTX1N 21 31 RxN1
NC 10 X_BT_WAKE2 GND 22 30 GND
4 11 WIFI_GND VBTX0P 23 29 RxP0
2 12 KEY_AD VBTX0N 24 28 RxN0
2 13 5V_MAIN GND 25 VBO FFC 51P 27 GND
3 14 POWER_KEY VBTXLOCKN0 26 26 LOCKN
1 15 WIFI_GND VBTXHTPDN0 27 25 HTPDN
11 16 SC_OPT_SENSE GND 28 24 GND
2022/09/22 04:50:40 (GMT+09:00)
BT
Antena
PSJ Board
G PSU
Board
CN6401
1-842-551-11
SJM20-28WLB/JAM CN400
NC 1 NC NC 30 STBY_3.3V
DC_DIMMER 2 26 #26 NC 29 FB_REF
BL_ON 3 22 #26 #26 6 28 BLINKING
PWM_DIMMER 4 27 #26 #26 4 27 PWM1_DIMMER
STBY_3.3V 5 24 #22 #26 2 26 DC_DIMMER
BLINKING 6 28 #26 NC 25 PWM2_DIMMER
AC_OFF_DET 7 NC #22 5 24 STBY_3.3V_IN
BL_ERR 8 21 NC 23 PWM3_DIMMER
POWER_ON 9 20 #26 #26 3 22 BL_ON
GND 10 19 #22 #26 8 21 BL_ERR
GND 11 18 #22 #26 9 20 POWER_ON
GND 12 17 #22 #22 10 19 GND
REG12V 13 16 #22 #22 11 18 GND
REG12V 14 15 #22 #22 12 17 GND
REG12V 15 14 #22 #22 13 16 REG_19V_12V
REG12V 16 13 #22 #22 14 15 REG_19V_12V
REG12V 17 12 #22 #22 15 14 REG_19V_12V_Audio
REG12V 18 11 #22 #22 16 13 REG_12V
GND 19 10 #22 #22 17 12 REG_19V_12V_Audio
GND 20 9 #22 #22 18 11 REG_12V
TCON_GND 21 8 #22 #22 19 10 GND
GND 22 NC #22 20 9 GND
TCON_GND 23 7 #22 #22 21 8 GND
TCON_ON 24 3 #26 #22 23 7 GND
TCON_VCC12V 25 4 #22 NC 6 DC_DET_VTH/LD_MODE_SW
TCON_VCC12V 26 2 #22 NC 5 GND
TCON_VCC12V 27 NC #22 25 4 T-CON_VCC12V
TCON_VCC12V 28 NC #26 24 3 T-CON_ON
SJM20-28HG #22 26 2 T-CON_VCC12V
1-842-598-11 NC 1 VPP_PIC
1-843-925-11 1-843-917-11
PBDP-30V-S JST SM30B-PBDSS-TF
CN6101
SFP79-02WLB JAM
1-822-908-11
AC-N 1
AC-L 2 AC pigtail
CN6801
1-822-360-11
53426-0510 Molex
NC 1 To LS
+OUT1 2
NC(No land) 3
NC(No land) 4 To LS
-OUT1 5
CN3202
1 1 SP_MAIN_LP
2 2 SP_MAIN_LN
1 3 SP_MAIN_RP
2 4 SP_MAIN_RN
1-842-593-11 1-842-566-12
PBVP04V-S SM04B-PBVSS-TB(LF)(SN)(PS)
1-535-807-31
JST SPS-01T-187*
SPEAKER L+ 1 1 #24
Front L- 2 2 #24
Lch 1-780-577-11
JST WSPS-01T-110B*
1-535-807-31
JST SPS-01T-187*
SPEAKER R+ 1 3 #24
Front R- 2 4 #24
Rch 1-780-577-11
JST WSPS-01T-110B*
1-CN5 1 Ca
LS Bar A1
1-A2 2 An
2-A1 1 Ca
LS Bar A2
1-A3 2 An
2-A2 1 Ca
LS Bar A3
1-A4 2 An
2-A3 1 Ca
LS Bar A4
1-A5 2 An
2-A4 1 Ca
LS Bar A5
1-A6 2 An
2-A5 1 Ca
LS Bar A6
1-A7 2 An
2-A6 1 Ca
LS Bar A7
1-A8 2 An
2-A7 1 Ca
LS Bar A8
1-A9 2 An
2-A8 1 Ca
LS Bar A9
1-A10 2 An
2-A9 1 Ca
LS Bar A10
1-CN2 2 An
JST SFKR-02V-2
119
SYS SET
3 key Source
BAX_F CN3800 To B-board To source board
CN203
BCX Board GND 1 51 GND T-con Board From T-con board Board
1-474-647-12 HUS_GND 1 15 #30 VBTX7P 2 50 RxP7
HUS_KEY_AD 2 12 #30 VBTX7N 3 49 RxN7
HUS_POWER_KEY 3 14 #30 GND 4 48 GND
1-822-693-11 1-821-900-11 VBTX6P 5 47 RxP6 PANEL 68P FFC FFC 68P
JAM SZ15-03WLR SZ15-03HGR VBTX6N 6 46 RxN6 PANEL 68P FFC
GND 7 45 GND
VBTX5P 8 44 RxP5
VBTX5N 9 43 RxN5
GND 10 42 GND Deren: 0.5pitch 68pin 1.8H FPC
VBTX4P 11 41 RxP4 Deren: 0.5pitch 68pin 1.8H FPC
CN1000 VBTX4N 12 40 RxN4
7 1 WIFI_STBY_3.3V GND 13 39 GND
14 2 X_WIFI_BT_RST VBTX3P 14 38 RxP3
1 3 SC_STBY_3.3V VBTX3N 15 37 RxN3
SN/SNH 65’
13 4 X_WIFI_WAKEUP GND 16 36 GND
15 5 WIFI_GND VBTX2P 17 35 RxP2
12 6 X_BT_WAKEUP VBTX2N 18 34 RxN2
9 7 WIFI_GND GND 19 33 GND
Main Harness NC 8 3D_LR VBTX1P 20 32 RxP1
8 9 WIFI_GND VBTX1N 21 31 RxN1
NC 10 X_BT_WAKE2 GND 22 30 GND
4 11 WIFI_GND VBTX0P 23 29 RxP0
2 12 KEY_AD VBTX0N 24 28 RxN0
2 13 5V_MAIN GND 25 VBO FFC 51P 27 GND
3 14 POWER_KEY VBTXLOCKN0 26 26 LOCKN
1 15 WIFI_GND 27
2022/09/22 04:50:40 (GMT+09:00)
VBTXHTPDN0 25 HTPDN
11 16 SC_OPT_SENSE GND 28 24 GND
3 17 SC_GND GND/SA_MODE 29 23 AGING_MODE
Smart Core 12 18 SC_SIRCS SPI_CS 30 22 SPI_CS
10 19 SC_MAIN_3.3V SPI_CK 31 21 SPI_CLK
CN001 4 20 SC_LED_AMBER PANEL_BINT/X_WP 32 20 B_INT (High:Write / L/Open: Protect)
STBY3.3V 1 3 #30 9 21 SC_GND SCL 33 19 SCL
HCI-L 5V_MAIN 2 13 #30 5 22 SC_LED_PWM_W SDA 34 18 SDA
GND 3 17 #30 NC 23 KEY_GND SPI_DI 35 17 SPI_DO
LED_AMBER 4 20 #30 8 24 SC_LED_PWM_G SPI_DO 36 16 SPI_DI
LED_PWM_W 5 22 #30 NC 25 (TS_SCL) 3D_SYNC_OUT 37 15 3D_MEMC
LEY_STBY_PWM_R 6 28 #30 7 26 SC_LED_PWM_B SPI_EN 38 14 SPI_EN
5.2 Connector Diagram
BT
Antena
PSJ Board
G PSU
Board
CN6401
1-842-551-11
SJM20-28WLB/JAM CN400
BLINKING 1 28 NC 30 STBY_3.3V
PWM1_DIMMER 2 27 #26 NC 29 FB_REF
DC_DIMMER 3 26 #26 #26 1 28 BLINKING
PWM2_DIMMER 4 NC #26 2 27 PWM1_DIMMER
STBY3.3V 5 24 #22 #26 3 26 DC_DIMMER
NC 6 NC NC 25 PWM2_DIMMER
BL_ON 7 22 #22 5 24 STBY_3.3V_IN
BL_ERR 8 21 NC 23 PWM3_DIMMER
POWER_ON 9 20 #26 #26 7 22 BL_ON
GND 10 19 #22 #26 8 21 BL_ERR
GND 11 18 #22 #26 9 20 POWER_ON
GND 12 17 #22 #22 10 19 GND
REG12V 13 16 #22 #22 11 18 GND
REG12V 14 15 #22 #22 12 17 GND
REG12V 15 14 #22 #22 13 16 REG_19V_12V
REG12V 16 13 #22 #22 14 15 REG_19V_12V
REG12V 17 12 #22 #22 15 14 REG_19V_12V_Audio
REG12V 18 11 #22 #22 16 13 REG_12V
GND 19 10 #22 #22 17 12 REG_19V_12V_Audio
GND 20 9 #22 #22 18 11 REG_12V
GND 21 8 #22 #22 19 10 GND
GND 22 NC #22 20 9 GND
GND 23 7 #22 #22 21 8 GND
GND 24 5 #22 #22 23 7 GND
TCON_VCC12V 25 4 #22 NC 6 DC_DET_VTH/LD_MODE_SW
TCON_ON 26 3 #26 #22 24 5 GND
TCON_VCC12V 27 2 #22 25 4 T-CON_VCC12V
TCON_VCC12V 28 NC #26 26 3 T-CON_ON
SJM20-28HG #22 27 2 T-CON_VCC12V
1-842-598-11 NC 1 VPP_PIC
1-843-925-11 1-843-917-11
CN6101 PBDP-30V-S JST SM30B-PBDSS-TF
SFP79-02WLB/JAM
1-822-908-11
AC-N 1
AC-L 2
AC pigtail
CN6801
1-822-360-11
53426-0510 Molex
NC 1
+OUT1 2
NC 3
NC 4
-OUT1 5
CN3202
1 1 SP_MAIN_LP
2 2 SP_MAIN_LN
1 3 SP_MAIN_RP
2 4 SP_MAIN_RN
1-842-593-11 1-842-566-12
PBVP04V-S SM04B-PBVSS-TB(LF)(SN)(PS)
1-535-807-31
JST SPS-01T-187*
SPEAKER L+ 1 1 #24
Front L- 2 2 #24
Lch 1-780-577-11
JST WSPS-01T-110B*
1-535-807-31
JST SPS-01T-187*
SPEAKER R+ 1 3 #24
Front R- 2 4 #24
Rch 1-780-577-11
JST WSPS-01T-110B*
2 Ca
LS #1
1 An
2 Ca
LS #2
1 An
2 Ca
LS #3
1 An
2 Ca
LS #4
1 An
2 Ca
LS #5
1 An
2 Ca
LS #6
1 An
JST SFKR-02V-2
120
SYS SET
3 key Source
BAX_F CN3800 To B-board To source board
CN203
BCX Board GND 1 51 GND T-con Board From T-con board Board
1-474-647-12 HUS_GND 1 15 #30 VBTX7P 2 50 RxP7
HUS_KEY_AD 2 12 #30 VBTX7N 3 49 RxN7
HUS_POWER_KEY 3 14 #30 GND 4 48 GND
1-822-693-11 1-821-900-11 VBTX6P 5 47 RxP6 PANEL 96P FFC FFC 96P
JAM SZ15-03WLR SZ15-03HGR VBTX6N 6 46 RxN6 PANEL 96P FFC
GND 7 45 GND
VBTX5P 8 44 RxP5
VBTX5N 9 43 RxN5
GND 10 42 GND UJU: PF050-096B-C20-F
VBTX4P 11 41 RxP4 Yeonho 05002HR-H96G5(G) MOLEX: 1042679617
CN1000 VBTX4N 12 40 RxN4 UJU FF050-O96B-C15-A
7 1 WIFI_STBY_3.3V GND 13 39 GND
14 2 X_WIFI_BT_RST VBTX3P 14 38 RxP3
1 3 SC_STBY_3.3V VBTX3N 15 37 RxN3
13 4 X_WIFI_WAKEUP GND 16 36 GND
15 5 WIFI_GND VBTX2P 17 35 RxP2
12 6 X_BT_WAKEUP VBTX2N 18 34 RxN2
9 7 WIFI_GND GND 19 33 GND
SN/SNH 75’
Main NC 8 3D_LR VBTX1P 20 32 RxP1
8 9 WIFI_GND VBTX1N 21 31 RxN1
NC 10 X_BT_WAKE2 GND 22 30 GND
4 11 WIFI_GND VBTX0P 23 29 RxP0
2 12 KEY_AD VBTX0N 24 28 RxN0
2 13 5V_MAIN GND 25 VBO FFC 51P 27 GND
3 14 POWER_KEY VBTXLOCKN0 26 26 LOCKN
1 15 WIFI_GND VBTXHTPDN0 27 25 HTPDN
11 16 SC_OPT_SENSE GND 28 24 GND
3 17 SC_GND GND/SA_MODE 29 23 AGING_MODE
Smart Core 12 18 SC_SIRCS SPI_CS 30 22 SPI_CS
2022/09/22 04:50:40 (GMT+09:00)
OPT_SENSE 11 16 #30 NC 43 9 NC
SIRCS 12 18 #30 1-820-162-12 12V 44 8 12V
1-821-139-11 1-821-126-11 MOLEX 501571-3007 12V 45 7 12V
PANEL96P FFC FFC 96P PANEL 96P FFC
JAM SYT10-12WS SYT10-12HG 12V 46 6 12V
12V 47 5 12V
12V 48 4 12V
12V 49 3 12V
12V 50 2 12V UJU: PF050-096B-C20-F MOLEX: 1042679617
12V 51 1 12V Yeonho 05002HR-H96G5(G) UJU FF050-O96B-C15-A
USB Cabl e 1-842-546-22, IPEX (BM11) FI-RXE51S-HF
GND 15 5 #30 1-844-527-11, MOLEX (BM10)
Wifi/BT J20H088 RST_L 14 2 #30 FFC Direct Connector : IPEX
WOW_L 13 4
WOBT1_L 12 6 #30
J20H088 WOBT2_L 11 NC
1-458-966-11 VSYNC 10 NC
GND 9 7 #30
GND 8 9 #30
VCC 7 1 #30 CN1002
VCC 6 5 1 BLK#28 USB 5 1 WIFI_STBY_3.3V
VCC 5 1 1 RED#28 USB 3 2 WIFI_USB_M
GND 4 11 #30 USB 2 3 WIFI_USB_P
DM 3 2 1 WHT#28 USB NC 4 NC
DP 2 3 1 GRN#28 USB 6 5 WIFI_STBY_3.3V
GND 1 Shel l 1 Shi el d USB 1 Shell WIFI_GND
1-844-754-11 1-849-996-11 GA: 1-844-049-21
JAM STA12-15WH-ET (JAM) STA12-15HG ACON u-USB Plug SMK CSS5305-6H02E
BT
Antena
PSJ Board
G PSU
Board
CN6401
1-842-551-11
SJM20-28WLB/JAM CN400
BLINKING 1 28 NC 30 STBY_3.3V
PWM1_DIMMER 2 27 #26 NC 29 FB_REF
DC_DIMMER 3 26 #26 #26 1 28 BLINKING
PWM2_DIMMER 4 25 #26 #26 2 27 PWM1_DIMMER
STBY3.3V 5 24 #22 #26 3 26 DC_DIMMER
NC 6 NC #26 4 25 PWM2_DIMMER
BL_ON 7 22 #22 5 24 STBY_3.3V_IN
BL_ERR 8 21 NC 23 PWM3_DIMMER
POWER_ON 9 20 #26 #26 7 22 BL_ON
GND 10 19 #22 #26 8 21 BL_ERR
GND 11 18 #22 #26 9 20 POWER_ON
GND 12 17 #22 #22 10 19 GND
REG12V 13 16 #22 #22 11 18 GND
REG12V 14 15 #22 #22 12 17 GND
REG12V 15 14 #22 #22 13 16 REG_19V_12V
REG12V 16 13 #22 #22 14 15 REG_19V_12V
REG12V 17 12 #22 #22 15 14 REG_19V_12V_Audio
REG12V 18 11 #22 #22 16 13 REG_12V
GND 19 10 #22 #22 17 12 REG_19V_12V_Audio
GND 20 9 #22 #22 18 11 REG_12V
GND 21 8 #22 #22 19 10 GND
GND 22 NC #22 20 9 GND
GND 23 7 #22 #22 21 8 GND
GND 24 5 #22 #22 23 7 GND
TCON_VCC12V 25 4 #22 NC 6 DC_DET_VTH/LD_MODE_SW
TCON_ON 26 3 #26 #22 24 5 GND
TCON_VCC12V 27 2 #22 25 4 T-CON_VCC12V
TCON_VCC12V 28 NC #26 26 3 T-CON_ON
SJM20-28HG #22 27 2 T-CON_VCC12V
1-842-598-11 NC 1 VPP_PIC
1-843-925-11 1-843-917-11
CN6101 PBDP-30V-S JST SM30B-PBDSS-TF
SFP79-02WLB/JAM
1-822-908-11
AC-N 1 AC pigtail
AC-L 2
CN6801
1-822-361-11
53426-0610 Molex
+OUT1 1
+OUT2 2
NC 3
NC 4
-OUT1 5
-OUT2 6
CN3202
1 1 SP_MAIN_LP
2 2 SP_MAIN_LN
1 3 SP_MAIN_RP
2 4 SP_MAIN_RN
1-842-593-11 1-842-566-12
PBVP04V-S SM04B-PBVSS-TB(LF)(SN)(PS)
1-535-807-31
JST SPS-01T-187*
SPEAKER L+ 1 1 #24 --> #22
Front L- 2 2 #24 --> #22
Lch 1-780-577-11
JST WSPS-01T-110B*
1-535-807-31
JST SPS-01T-187*
SPEAKER R+ 1 3 #24 --> #22
Front R- 2 4 #24 --> #22
Rch 1-780-577-11
JST WSPS-01T-110B*
2 Ca
LS #1
1 An
2 Ca
LS #2
1 An
2 Ca
LS #3
1 An
2 Ca
LS #4
1 An
2 Ca
LS #5
1 An
2 Ca
LS #6
1 An
2 Ca
LS #7
1 An
2 Ca
LS #8
1 An
JSTSFKR-02V-2
121
SYS SET
2022/09/22 04:50:40 (GMT+09:00)