HIGH-PERFORMANCE
FIBERGLASSFILTER1.GENERAL
Check filter for any evidence of damage due to rough handling
in shipment. If filter is damaged, notify the carrier immediately.
The filter may only be used for the filtering of swimming
pool water, garden pond water or similar applications.
2.INSTALLATION INSTRUCTIONS
Please note:There can be specific needs to install filters nearby
swimming pools,garden ponds or such places.The filter should
be placed ona flat,solid foundation. Install the filter and pump
in a sheltered location, ensuring ventilation and adequate access
for servicing. Place the filter in its permanent location. Make sure
you can reach the valve easily. Then fix the piping.Use only
plastic piping. Size all piping adequately and keep the number of
elbows to a minimum.
3.O0PERATION
Look inside, move the top diffuser to one side and check the
lower distribution system for loose or broken laterals. Ensure
air bleed pipe is connected to lower distributor. Connect
valve to the filter using pipes with unions. Fill the tank to
1/3rd level with water before attempting to fill with media.
Fill the filter with the specified quantity of sand.Replace
4top diffuser and ensure correct position of air bleed pipe,
through top diffuser and connected to air bleed valve.Ensure
pressure gauge is tight fit to filter lid .Place O'ring with lid
on filter tank and tighten nuts with washers evenly. Take care,
do not over tighten.Connect the pump and return pipes to the
valve 816), turn valve to position RINSE, start the pump and
run for atleast 1 minute. :
CAUTION:
NEVER SHIFT VALVE HANDLE POSITION WHILE PUMP IS
RUNNING.NEVER DISASSEMBLE VALVE WHILE FILTER IS
UNDER PRESSURE. :
4.FILTRATION
1. Shift off the pump.
2.Shift valve handle to position ‘Filtration’ .
3. Start the pump.
4, Note here the pressure of the pressure gauge.
5.TO CLEAN (BACKWASH) THE FILTER
When the pressure rises approximately 0.5 bar above the
recommended pressure it is time to backwash.
1. Shut off the pump.
2. Shift the valve handle to "Backwash"3. Start pump and let it run until water is clean (about 3 minutes.)
4. Shut off the pump.
5, Shift valve handle to "Rinse"position.
6. Start pump and run for approximately one minute.
7. Shut off the pump.
8. Shift valve handle to position "Filtration"and start the pump.
6.MAINTENANCE
The filter needs no maintenance.
7.WINTERIZING
Protect the pump, the filter and the piping from freezing.Open
the drain and shift the valve handle to "Backwash".
8.REPLACING THE SAND
Open the drain and let the water flow out.
Remove the sand and folow instructions oultined in 4 operation.
9.WARRANTY
The manufacturer is not responsible for transport damage.
In case of damage notify carrier immediately.
Warranty:Bobin wound filter tank 3 years, filters componants 2
years, starting from the production date.SERIES-HIGH PERFORMANCE FILTER(TOP MOUNT, CLAMP)
Model | garcet | Max Kos |R8x 710M | sana kG | Valve Size
16 1.4 250 100 30, ipa}
18 1.77 250 | 130 40 1s
20 2.18 250 160 3 [ 80> ae
24 3.14 | 250 230. 1508 =|
25 3.41 [| 250 250 155 15
28 44 250 280 185 | 15°
30 4.94 250 350 200, [| 2°
32 5.58 250 390 210 | |
36 7.07 250 470 300 =
40 8.73 250 530 410 2
48 72.57 | 250 570 560 =
56 16.57 | 250. 580 1500 2
48 12.57 | 250 | 670 | 560 | 25"
756 | 16.57 | 250 680 | 1500 25°