Professional Documents
Culture Documents
Getac F110 Series Service Manual R01
Getac F110 Series Service Manual R01
Getac F110 Series Service Manual R01
Service Manual
Tablet PC
_____________
Information in this publication is subject to change without notice. © 2016 Getac
Inc. All rights reserved.
cover.
Caution: Whenever you service the computer, you must first power down
the computer and unplug all peripheral devices, removing the power cord
and battery.
Recommended Tools
4. Sleeve
3 Block Diagram.................................................................................... 20
4 Diagnosis.............................................................................................. 21
6 Disassembly/Reassembly.................................................................... 41
7 Firmware Upgrade............................................................................. 90
8 Exploded View.................................................................................... 92
The new F110 is fully -rugged tablet, high - portability industrial tablet
computer. It can be used in the vehicle, field, and office. The tablet computer
also can connect with a docking to extend the capability of I/O devices.
The F110 design Intel Skylake platform, the Skylake (processor, PCH) is
designed for a one-chip platform as opposed to the traditional three-chip
platforms (processor, GMCH, and ICH).
The F110 will support the Intel® Core™ Skylake Processor, Skylake is the
next generation of 64-bit, multi-core mobile processor built on 14-nanometer
process technology, and Skylake build-in MCH supported DDR3L(1600MHz),
GMCH(UMA video control IC). F110 use low power consumption unit
(15W).
4G CARD
Bluetooth module
8MCCD
Digitizer
Webcam,
The Mobile Intel® Series 8 chipset provides extensive I/O support. Functions
and capabilities include:
• PCI Express* Base Specification, Revision 3.0 support for up to eight ports
with transfers up to 8 GT/s
• ACPI Power Management Logic Support, Revision 4.0a
• Enhanced DMA controller, interrupt controller, and timer functions
• Integrated Serial ATA host controllers with independent DMA operation on
up to six ports
• USB host interface with two EHCI high-speed USB 2.0 Host controllers and
two rate matching hubs provide support for up to eight USB 2.0 ports and
one xHCI provides support for up to four SuperSpeed USB 3.0 ports.
• Integrated 10/100/1000 Gigabit Ethernet MAC with System Defense
• System Management Bus (SMBus) Specification, Version 2.0 with
additional support for I2C devices
• Supports Intel® High Definition Audio (Intel® HD Audio)
• Supports Intel® Rapid Storage Technology (Intel® RST)
• Supports Intel® Active Management Technology (Intel® AMT)
2
F110 provide one NGFF PCIE(USB- bus) slot for 4G module use. The
newest The EM7355 provides LTE, CDMA, and GPS connectivity for portable
and handheld computers, point-of-sale devices, telemetry products and other
machine-to-machine and vertical applications over several radio frequency
bands. (The modem is DC-HSPA+, HSPA+, HSDPA, HSUPA, WCDMA,
GSM, GPRS, and EDGE capable with functionality pending future firmware
support.)
A full set of software drivers and utilities are available to allow advanced
operating systems such as Windows 8 to take full advantage of the hardware
capabilities.
In F110, there are enough IO expanding capabilities for end user to use.
One DC jack for system power supply
One USB3.0 external ports
One Smart Card slot
One MIC/Headphone 4 pole combo jack
One RJ45 connector
Two battery connector
One 24-pin POGO connector for dock station
One DDR3L-SODimm 204-pin slot (internal)
One NGFF card slot (internal) for wireless module
One NGFF card slot (internal) for 4G modem module
One SIM card slot (internal)
One HDMI
10
11
12
13
16
17
18
19
20
21
4.2.1 No Power
When the power button is pressed, nothing happens, no fan activity is heard
and power indicator is not light up. Make sure that Power profile switch is
switched on.
22
23
24
25
26
Either an error message is shown, can not access the SSD or can not find
Operating System.
27
28
29
30
When the power button is pressed, power is OK, FAN doesn’t work.
31
32
33
34
35
38
39
40
Instructions
41
2. Pull the ribbon strip to lift the battery pack off the compartment.
42
3. Open the RFID Module. Disconnect the cable, then remove the RFID
Module.
43
44
45
4. Remove one STANDOFF (377102030001) lock the SSD Card, then remove
the SSD Card.
46
47
48
6. Disconnect the cable, Remove the holder, then remove the Battery Trans
Board.
49
50
51
52
53
54
14. Find the smart card FPC cable on the back of mother board. Disconnect the
smart card FPC cable
15. Disconnect the CMOS battery cable and then remove it from mother board
55
11. Pull the retaining clips outwards (1) and remove the Memory (2) on Mother
Board.
56
57
58
59
60
61
62
3. Open the Finger Print Module. Disconnect the cable, then remove the Finger
Print Module.
63
64
65
66
67
2. Set the RFID Module to the Part C. Fix the RFID Module using the seven
screws (371101610421) and one screw (371102010382)
68
2. Set the cover to the RFID Board. Fix the cover using the ten screws
(371102010382).
69
2. Set the PLATE to the part C. Fix the PLATE using the three screws
(371102010014).
70
2. Set the PLATE to the part C. Fix the PLATE using the three screws
(371102010014).
71
2. Set the PLATE to the part C. Fix the PLATE using the three screws
(371102010014).
72
2. Fix the Part A and the Part C using the sixteen screws (7970I69B3050).
73
2. Fix the holder using the four screws. Connect the cable.
74
2. Set the holder to the F110 Option Bay. Fix the holder using the two screws
(371102010383).
75
76
3. Fix the Rear Camera Module using the one screw (370102010409), and stick
the Mylar.
4. Set the holder to the MB. Fix the holder using the two screws
(7970I6402050).
77
2. Set the MB to part C. Fix the MB Board using the five screws
(371102010382). Connect the cables and antennas to the MB.
78
4. Set the holder to the MB. Fix the holder using the two screws
(7970I6402050).
5. Set the holder to the MB. Fix the holder using the two screws
(7970I6402050).
79
80
2. Set the antenna to the Part C. Fix the antenna using the two screws.
81
4. Set the WLAN antenna to the Part C. Fix the WLAN antenna using the two
screws.
82
2. Set the LCD holder to the Part C. Fix the LCD holder using the fifteen
screws (371102010432) and three screws (371101610320).
3. Set the Holder to the MB. Fix the Holder using the two screws
(7970I6402050).
84
85
87
88
2. Set the IO cover to the Part C. Fix the IO cover using the two screws
(37110201025A).
3. Close the IO cover. Slide the lock outward to the locked position.
89
CAUTION: Do not power down the system during the BIOS/KBC update
process! The system will reboot automatically when the BIOS/KBC update
process is completed.
5. The system will reboot automatically when the BIOS/KBC update process is
completed. check if BIOS/KBC version is correct and if BIOS/KBC is
updated successfully.
90
91
92
3
1
1 1
3 3
8
1
7
1
4 4
6
1
5 5
23-Dec-2015
5
1
2
1
6 6
+
TOL -
DATE MATERIAL SEE NOTES
23-Dec-2015 TREATMENT PROJECTION
RANGE Pla Met Ins Por Cab Pac Gas PCB
0~6 0.1 0.1 0.1 0.2 0.5 1 0.5 0.1 UNIT MM SCALE 1.00 DRAWING NAME EXP-SYS-ASSY-F110G3
4
6~30 0.1 0.1 .15 .25 1 1 0.5 0.1
1 DRAWN DESIGNED CHECKED APPROVED MATERIAL NO.
30~80 0.1 .15 0.2 0.3 2 1.5 1 0.1 MF TBD R 00
80~180 .15 .15 .25 0.3 2 2 1 .15
180~315 .15 0.2 0.3 0.4 2.5 2 1 .15 23-Dec-2015 23-Dec-2015
A B C D E F G H SHEET NO. 1 of 1
model name: MAIN-STRU-ASSY-F110G3 file name: EXP-SYS-ASSY-F110G3
5
2
7
1
8
1
3 1 3
1
2
1
4 4
11-Dec-2015
3
4 2
1
TOL +
- DATE MATERIAL SEE NOTES
11-Dec-2015 TREATMENT PROJECTION
5 RANGE Pla Met Ins Por Cab Pac Gas PCB 5
0~6 0.1 0.1 0.1 0.2 0.5 1 0.5 0.1 UNIT MM SCALE 1.00 DRAWING NAME BATT-DOOR-ASSY
6~30 0.1 0.1 .15 .25 1 1 0.5 0.1
DRAWN DESIGNED CHECKED APPROVED MATERIAL NO. MF TBD R
30~80 0.1 .15 0.2 0.3 2 1.5 1 0.1 00a
80~180 .15 .15 .25 0.3 2 2 1 .15
180~315 11-Dec-2015 11-Dec-2015
.15 0.2 0.3 0.4 2.5 2 1 .15
ITEM CONTENTS OF CHANGE RVS CHK APV M/D/Y 315~800 0.2 0.3 0.4 0.5 3 3 2 .15
Technology Corp.
A B C D E F SHEET No. 1 of 1
model name: TOOL-LESS-BATT-COVER-R00-1 file name: EXP-TOOL-LESS-BATT-COVER-F110
4
2 3 6 1
1 2 1
2 2
3 3
7
1
4 4
23-Dec-2015
5
1
1
1
TOL +
- DATE MATERIAL SEE NOTES
23-Dec-2015 TREATMENT PROJECTION
5 RANGE Pla Met Ins Por Cab Pac Gas PCB 5
0~6 0.1 0.1 0.1 0.2 0.5 1 0.5 0.1 UNIT MM SCALE 1.00 DRAWING NAME LCD-PLATE-ASSY-F110G3
6~30 0.1 0.1 .15 .25 1 1 0.5 0.1
DRAWN DESIGNED CHECKED APPROVED MATERIAL NO. MF TBD R
30~80 0.1 .15 0.2 0.3 2 1.5 1 0.1 00
80~180 .15 .15 .25 0.3 2 2 1 .15
180~315 .15 0.2 0.3 0.4 2.5 2 1 .15 23-Dec-2015 23-Dec-2015
ITEM CONTENTS OF CHANGE RVS CHK APV M/D/Y 315~800 0.2 0.3 0.4 0.5 3 3 2 .15
Technology Corp.
A B C D E F SHEET No. 1 of 1
model name: LCD-PLATE-ME-KIT-ASSY-F110G3 file name: EXP-LCD-PLATE-ASSY-F110G3
6
1
18
1
2
1
4
1 3
1
4 13 4
1
12
2
5 5
23-Dec-2015
15
1
6 11 6
1 20 14 +
TOL -
DATE MATERIAL SEE NOTES
23-Dec-2015 TREATMENT PROJECTION
1 1 RANGE Pla Met Ins Por Cab Pac Gas PCB
0~6 0.1 0.1 0.1 0.2 0.5 1 0.5 0.1 UNIT MM SCALE 1.00 DRAWING NAME EXP-COVER-FRONT-ASSY-F110G3
6~30 0.1 0.1 .15 .25 1 1 0.5 0.1
DRAWN DESIGNED CHECKED APPROVED MATERIAL NO. R
30~80 0.1 .15 0.2 0.3 2 1.5 1 0.1 MF TBD 00
80~180 .15 .15 .25 0.3 2 2 1 .15
180~315 .15 0.2 0.3 0.4 2.5 2 1 .15 23-Dec-2015 23-Dec-2015
A B C D E F G H SHEET NO. 1 of 1
model name: FRONT-COVER-ME-KIT-ASSY-F110G3 file name: EXP-FRONT-COVER-ASSY-F110G3
1 1
7
1
3 3
10
1
2
1
9
1
6
4 1 4
23-Dec-2015
8
3
1
2
TOL +
- DATE MATERIAL SEE NOTES
23-Dec-2015 TREATMENT PROJECTION
5 RANGE Pla Met Ins Por Cab Pac Gas PCB 5
0~6 0.1 0.1 0.1 0.2 0.5 1 0.5 0.1 UNIT MM SCALE 2.00 DRAWING NAME EXP-8M-CAMERA-ASSY-F110G3
6~30 0.1 0.1 .15 .25 1 1 0.5 0.1
DRAWN DESIGNED CHECKED APPROVED MATERIAL NO. MF TBD R
30~80 0.1 .15 0.2 0.3 2 1.5 1 0.1 00
80~180 .15 .15 .25 0.3 2 2 1 .15
180~315 .15 0.2 0.3 0.4 2.5 2 1 23-Dec-2015 23-Dec-2015
.15
ITEM CONTENTS OF CHANGE RVS CHK APV M/D/Y 315~800 0.2 0.3 0.4 0.5 3 3 2 .15
Technology Corp.
A B C D E F SHEET No. 1 of 1
model name: 8M-CAM-ASSY-F110G2 file name: EXP-8M-CAMERA-ASSY-F110G3
98
99
100
101
102
103
104
105